Professional Documents
Culture Documents
Knock Out Drum Compatibility Mode
Knock Out Drum Compatibility Mode
Dr.-Ing
Dr
Ing. Suherman
Teknik Kimia UNDIP
Pendahuluan
Fungsi: memisahkan campuran uap dan
cairan
Prinsip kerja: gaya gravitasi
mengakibatkan cairan jatuh ke bawah,
sedangkan uap bergerak ke atas pada
l j d
laju
desain
i minimum
i i
entrainment
t i
t
butiran cairan ke dalam uap
Separator uap-cairan juga dikenal
sebagai Flash Drum, Knock-out (KO)
Drum,, Knock-out p
pot,, Compressor
p
Suction Drum or Compressor Inlet Drum
Tipe Vertikal
Keuntungan tipe vertikal
- plot area yang diperlukan lebih kecil
-p
penghilangan
g
g p
padatan lebih mudah
- efisiensi penghilangan cairan tidak dipengaruhi oleh ketinggian
cairan, karena luasan vesel cukup membuat aliran uap tetap konstan
- umumnya volume vesel lebih kecil
Tipe Horizontal
K
Keuntungan
t
tipe
ti horisontal
h i
t l
lebih mudah untuk mengakomodasi sejumlah besar slug
cairan;
head yang diperlukan lebih kecil;
laju turunnya cairan lebih rendah, sehingga
meningkatkan
i k tk de-gassing
d
i dan
d pemecahan
h b
buih;
ih
Pemilihan Tipe
Application
Preferred orientation
Vertical
Reflux Accumulator
Horizontal
Compressor KO Drum
Vertical
Vertical
Flare KO Drum
Horizontal
Vertical
Steam Disengaging
g g g Drum
Horizontal
Working
g volume
between High Liquid
Level (HLL) and Low
Liquid Level (LLL)
HLL
LLL
HLA
LLL
1 Diameter vesel
1.
vt =
4gD p (l v )
3 v C
= Kt
l v
v
Application
Kt
Horizontal KO drum
0.25 fps
0.15 fps
0 25 fps
0.25
0.75 fps
0.33 fps
0.75 fps
Compressor suction
knockout drums
0 75 fps
0.75
7
2 Tinggi Vesel
2.
2.1 LLL = 0.2 m, for instrument 150 mm, and level instrument 50 mm
2.2. Liquid holdup = HLL-LLL
Service
Hold-up(min)
5-15
Reflux vessel
3-5
Fl
Flare
KO drum
d
Condensate Flash drum
20 30
20-30
3-5
2.3.
2
3 Jarak antara HLL dengan inlet nozzle = 0.3
03xD
D, atau minimum 0
0.3
3m
2.4 Diameter inlet nozzle (lihat sub bab 3)
2.5 Jarak antara inlet device dan TTL
a. Tanpa
T
demister,
d i t jarak
j k=0
0.7D
7D ((atau
t minimal
i i l0
0.9
9 m))
b. Dengan demister,
- jarak = 0.45D (atau minimal 0.9 m)
- plus 0
0.1
1 m untuk demister
- plus dari demister ke TTL = 0.15D (atau minimal 0.15 m)
3 Diameter Nozel
3.
3.1
3
1 Di
Diameter
t iinlet
l t nozzle,
l d
depend
d on the
th iinlet
l td
device
i d
depends
d on th
the iinlet
l t flflow
and on the type of inlet device
No inlet device:
m x vm2 = 1000
With inlet device:
m x vm2 = 1500
m = the density of mixture (MG+ML)/(QG+QL) (kg/m3)
vm = the density of mixture (QG+QL)/(1/4D2) (m/s)
3.2 Vapour outlet nozzle
G x vG2 = 3750
G = the vapour density (kg/m3)
vG = the vapour velocity (m/s)
3 3 Di
3.3
Diameter
t liliquid
id outlet
tl t , b
basis
i v=1
1m/s
/
9
10