Professional Documents
Culture Documents
Led Codes
Led Codes
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
Machine Coord
SpindleOn
MistOn
FloodOn
Jog Cont.
Jog Incr.
WorkOffsets Display.
Feed OverRide
Simulation On
Emergency Input Active
A axis Diam. Comp.
B Axis Diam Comp.
C Axis Diam Comp.
Softlimits on.
THC On
Spindle Accelerating
Spindle Decelerating
ToolPath On
Tool Offset in effect
Work Offset in effect
Throttle used for Override
Throttle used for Jog speed
BackLash on.
AutoLimits override in effect
Limits switches disenganged
Input#4 single step engaged
Torch OK active
Torch Up Active
Torch Down Active
Units/Rev Mode
Units/Min Mode
X Scaling Active
Y Scaling Active
Z Scaling Active
A Scaling Active
B Scaling Active
C Scaling Active
Jog Follow Active
Absolute Coord mode.
Incremental Coord Mode
Threading Sync Active
LaserTriggering Active
Z Inhibit Active
Ignoring Tool Change M6
Continuous Velocity Mode.
Repeat runs holding
Exact Stop Mode.
MPG Jog Mode
Continuous Jog Mode
X Axis MPG mode
Y Axis MPG mode
Z Axis MPOG mode
A Axis MPG Mode
B Axis MPG Mode
C Axis MPG Mode
Optional Stop M1 enabled
Block Delete mode enabled
Offline Active
Actual Spindle speed in Use.
Waiting for thread trigger point
70
71
72
73
74
75
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
Plunging Disabled
Spindle Speed Stable
IJ Mode Abs
IJ Mode Incremental
TeachFile is open
G92 in effect
OUTPUT4 Active
OUTPUT5 Active
Output6 Active
Engine in Pause state
Tangental control in effect
Single Step mode active
Jog Enabled
CV Feedrate descriminator enabled
Enhance pulseing Off
X Axis Enabled
Y Axis Enabled
Z Axis Enabled
A Axis Enabled
B Axis Enabled
C Axis Enabled
Diameter Mode enabled
MultiSlot Spindle Input enabled
HotKeys Enabled
Units/Minute mode
Units/Rev Mode
Running in Reverse
X MPG enabled MPG #2
Y MPG Enabled MPG #2
Z MPG enabled MPG #2
A MPG Enabled MPG #2
B MPG enabled MPG #2
C MPG Enabled MPG #2
Dual MPG Taper Mode enabled
Dual MPG Jog Mode enabled
MPG Velocity Mode
G96 mode in effect
Coordinate system Rotated
Rapid Speed OverRide
Formula corrections on.
Partial move holding
Running in Reverse
Feedrate Bypass Enabled
Front toolpost active
Rear Toolpost active
Spindle running in CCW
MPG Velocity mode selected)
MPG Vel/Step mode enabled
MPG Single Step enabled
MPG Multistep enabled
External XJog++ active
External XJog-- Active
External YJog++ active
External YJog-- Active
External ZJog++ active
External ZJog-- Active
External AJog++ active
External AJog-- Active
Toolpath Zoom locked on
Toolpath PanState locked on
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
999
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
A Homed
B Homed
C Homed
Dwell in effect
Joystick On
Softlimits On
Machine Coorindates On
Exact Stop Condition
Work Offsets in Effect
Incremental Jog
Continous Jog
OUTPUT1 Active
OUTPUT2 Active
OUTPUT3 Active
OUTPUT4 Active
Probe Input Active
Index Input Active
LimitOverRide Input Active
X++ Limit Active
X-- Limit Active
X Home Active
Y++ Limit Active
Y-- Limit Active
Y Home Active
Z++ Limit Active
Z-- Limit Active
Z Home Active
A++ Limit Active
A-- Limit Active
A Home Active
B++ Limit Active
B-- Limit Active
B Home Active
C++ Limit Active
C-- Limit Active
C Home Active
Enable1 Active
Enable2 Active
Enable3 Active
Enable4 Active
Enable5 Active
Enable6 Active
OUTPUT1 Active
OUTPUT2 Active
OUTPUT3 Active
DigTrigger output Active