Professional Documents
Culture Documents
AN7125
Dual Channel BTL Power Amplifier
Overview
Unit : mm
(10.0)
29.60.3
(1.27)
+0.15
R1.8
3.50.3
1.450.15
1
(1.2)
19.10.3
21.90.3
1.800.15
1.20.1
(12.5)
+0.10
0.25 0.05 2.54
0.6
20.00.3
Features
3.6
(10.0)
29.750.30
28.00.3
(1.3)
12
7.70.3
HSIP012-P-0000A
Applications
Radio-cassette
Block Diagram
REF
TSD
protection
circuit
12
10
11
GND
GND
Mute
3
GND
VCC
Standby
circuit
AN7125
Pin Descriptions
Pin No.
Description
Pin No.
Description
VCC
Pre GND
ch.2 Input
Mute
10
Standby
11
ch.1 Input
12
Symbol
Ratings
Unit
VCC
24
ICC
6.0
PD
38.5
Topr
25 to +75
Storage temperature
Tstg
55 to +150
Symbol
Range
Unit
VCC
6.0 to 18.0
Supply voltage
*1
Supply current
Power dissipation
*2
Symbol
Conditions
Typ
Max
Unit
ICQ
VIN = 0 mV
100
210
mA
VNO
0.27
0.5
mVrms
GVC
VIN = 20 mV
38
40
42
dB
THD
VIN = 20 mV
0.07
0.4
PO
THD = 10 %
10
12
Channel balance
CB
VIN = 20 mV
dB
CT
55
70
dB
350
350
mV
*1
Voltage gain
Total harmonic distortion
Channel crosstalk
*2
*1
Standby current
Muting effects
*2
*2
VOFF
RG = 6.2 k
RR
50
60
dB
ISTB
VIN = 0 mV
10
MT
VIN = 20 mV
70
80
dB
Min
AN7125
Equivalent Circuit
Function
Status
VCC :
VCC input
typ. : 12 V
ch.1 O/P :
VCC/2
Pin2
4
600
0V
30 k
ch.1 O/P :
VCC/2
Standby :
1
5
VTH = 2.8 V
30 k
100 100
STB on = 0 V/GND
5 k
5 k
10 k 2 k
2 k
8
ch.1 Input :
200
400
0V
Pin6,8
30 k
Pre GND :
Input ground pin.
0V
AN7125
Equivalent Circuit
Function
ch.2 Input :
200
400
Status
0V
Pin6,8
30 k
Mute :
VTH = 1.5 V
Mute off = 0 V
3.6 k
20 k
10
ch.2 Output :
VCC/2
Pin10
12
11
12
600
30 k
11
ch.2 Output :
ch.2 positive phase output pin
VCC/2
0V
AN7125
VCC
2200 F
4
51 k
5V
STB
Cs
Cs
0.22 F
2.2
RL
4
OUT1
0.22 F
2.2
5
10 F
8.2 k
MUTE
OUT1
Output1
3 GND
IN1
VCC
12 V
Input
7 GND
9
33 F
IN2
10
OUT2
11
Output2
GND
12
OUT2
0.22 F
2.2
RL
4
0.22 F
2.2
STB 'Off'
5V
STB 'On'
0V
Mute 'Off'
0V
Mute 'On'
5V
Applications Precautions
1. External heatsink is needed when used. External heatsink should be fixed to the chassis.
2. Fin of the IC can be connected to GND.
3. Please prevent output to VCC short and output to GND short.
4. The temperature protection circuit will operate at Tj around 150 C.
However, if temperature decrease, the protection circuit will automatically be decreased and resume
normal operation.
AN7125
Technical Information
HSIP012-P-0000A
PD Ta
80
70
62.5 W
60
50
(1)
40
30
20.8 W
20
(2)
15.6 W
(3)
10
3.0 W
(4)
0
0
25
50
75
100
125
150
10
t = 0.2 ms
IC (A)
5
t = 1.0 ms
2
t = 10 ms
1
0.5
0.2
0.1
1
10
VCE (V)
20
50
100
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative characteristics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.