Professional Documents
Culture Documents
Cafco FENDOLITE® MII - Product Datasheet
Cafco FENDOLITE® MII - Product Datasheet
www.promat-oilandgas.com
QUALITY
ASSURANCE
Promat
products
are
manufactured to stringent
quality control systems to
assure that our customers
receive materials made to
the highest standards.
Operating to these standards
means that all activities,
which have a bearing upon
quality, are set out in written
procedures.
Systematic and thorough
checks are made on all
materials and their usage.
Test equipment is subjected
to regular checks and is
referred back to national
standards.
The information given in
this data sheet is based on
actual tests and is believed
to be typical of the product.
No guarantee of results
is implied however, since
conditions of use are beyond
our control.
INTRODUCTION
Cafco FENDOLITE MII is a spray applied, single package factory controlled premix, based on vermiculite and
Portland cement.
Cafco FENDOLITE MII produces a monolithic coating able to withstand the thermal shocks experienced in a high
intensity hydrocarbon fire. Concrete structures in particular, will be protected from explosive spalling when coated
with Cafco FENDOLITE MII.
Although low in density, thus significantly reducing dead load, Cafco FENDOLITE MII is highly durable and will not
crack or spall under mechanical impact.
Cafco FENDOLITE MII is used for application on construction elements such as individual steel or concrete sections
particularly where off-site application is required. It is also suitable for use on structures and vessels in the oil, gas,
petrochemical and power industries.
Theoretical coverage
Cure
By hydraulic set
Initial set
Density (Nominal)
Combustibility
Smoke generation
Thermal conductivity
Corrosion resistance
pH value
12.0 - 12.5
Sound absorption
Fire resistance
ADVANTAGES
Proven fitness for purpose worldwide.
Over 25 years service.
Unrivalled track record.
Unequalled knowledge and experience.
Proven whole life value.
Available worldwide; supplied and installed.
Substrate preparation
The substrate must be clean, dry and free from visible moisture (including
condensation), concrete laitance, formwork release oils, loose millscale,
loose rust and any other condition preventing good adhesion.
Concrete curing agents should not be used.
Mesh reinforcement
Most fire tests conducted have been carried out without mesh
reinforcement, to demonstrate the ability of Cafco FENDOLITE MII to stay
in place under the most severe fire conditions. However, for maximum
long term in service durability, the use of lightweight mesh reinforcement
is recommended for exterior work and for interior use where vibration or
mechanical damage and the possibility of subsequent de-bonding exist.
APPLICATION
Initial steps
Methods
Cafco FENDOLITE MII may also be float or roller finished or left with
CafcoFENDOLITETG.
A hand applied patching mix is available for minor repairs. Please refer to
product data sheet of CafcoFENDOLITETG
Limitations
Cafco FENDOLITE MII may be applied when the substrate and air
temperatures are at least 2C and rising, but should not be applied if the
substrate or air temperatures are less than 4C and falling. Maximum
substrate and air temperature is 50C.
HEALTH AND
SAFETY
Adequate ventilation must be
provided during use. Avoid
contact with the skin and
eyes by using eye protection,
gloves, barrier cream and a
face mask.
If the product comes into
contact with the skin, wash
immediately with soap
and water. If the eyes are
affected, flush with plenty
of water and seek medical
attention immediately.
A safety data sheet is
available from Promat upon
request.
Promat
activities
are
conducted with due regard
to all statutory requirements
with appropriate safeguards
against exposing employees
and the public to health and
safety risks.
TOP COATING
Under certain circumstances, CAFCO TOPCOAT 200 and/or other nominated top coatings may be used as
protection from frequent wash down, long term chemical spills, or for improved resistance to fungal, algal and
bacterial growth.
PACKAGING
20kg bags.
STORAGE
Off the ground and kept dry until ready for use.
SHELF LIFE
Maximum 12 months.
ENVIRONMENTAL
Do not discharge into drains, watercourses or soil.
Not readily biodegradable.
Not expected to bioaccumulate.
Not expected to be toxic to aquatic life except at high concentrations.
All physical and mechanical values are averages based on standard production and tested according to internal procedures. The typical values are
given for guidance. The figures can change dependent on the test methods used. If a particular value is of prime importance for a specification, please
consult Promat Technical Department.
Bormstraat 24
2830 Tisselt
Tel: +32 15 718 100
Fax: +32 15 718 109
Email: info@promat-international.com
www.promat-international.com
www.promat-tunnel.com
www.promat-marine.com
www.promat-oilandgas.com
AUSTRALIA
Promat Australia Pty. Ltd.
1 Scotland Road
SA 5031 Mile End South
Tel: 1800 Promat (776 628)
Fax: +61 8 8352 1014
Email: mail@promat.com.au
www.promat-ap.com
AUSTRIA
Promat GmbH
St.-Peter-Strae 25
4021 Linz
Tel: +43 732 6912 0
Fax: +43 732 6912 3740
Email: info@promat.at
www.promat.at
Promat GmbH
RUSSIA
Promat A+B
GERMANY
Promat GmbH
SINGAPORE
Promat Building System Pte. Ltd.
BP 66 Rue de LAmmandier
78540 Vernouillet
Tel: +33 1 3979 6160
Fax: +33 1 3971 1660
Email: info@promat.fr
www.promat.fr
Scheifenkamp 16
40878 Ratingen
Tel: +49 2102 493 0
Fax: +49 2102 493 111
Email: mail@promat.de
www.promat.de
HONG KONG
Promat International (Asia Pacific) Ltd.
Room 1010, C.C. Wu Building
302-308 Hennessy Road, Wanchai
Tel: +852 2836 3692
Fax: +852 2834 4313
Email: apromath@promat.com.hk
www.promat.com.hk
INDIA
Promat (Malaysia) Sdn. Bhd. (India Representative Office)
610-611, Ansal Imperial Tower
C-Block, Community Centre
Naraina Vihar, Naraina
110028 New Delhi
Tel: +91 11 2577 8413
Fax: +91 11 2577 8414
Email: info-india@promat-asia.com
www.promat-ap.com
ITALY
Promat S.p.A.
CHINA
Promat China Ltd.
CZECH REPUBLIC
Promat s.r.o.
FRANCE
Promat S.A.S.
MALAYSIA
Promat (Malaysia) Sdn. Bhd.
NETHERLANDS
Promat B.V.
Ckalova 22/784
16000 Praha 6 - Bubenec
Tel: +420 2 2439 0811
Fax: +420 2 3333 3576
Email: promat@promatpraha.cz
www.promatpraha.cz
Vleugelboot 22
3991 CL Houten
PO Box 475
3990 GG Houten
Tel: +31 30 241 0770
Fax: +31 30 241 0771
Email: info@promat.nl
www.promat.nl
DENMARK
Promat Nordic
POLAND
Promat TOP Sp. z o.o
Kometvej 36
6230 Rdekro
Tel: +45 7020 0482
Fax: +45 7466 1020
Email: info@promat.nu
www.promat.nu
ul. Przeclawska 8
03 879 Warszawa
Tel: +48 22 212 2280
Fax: +48 22 212 2290
Email: top@promattop.pl
www.promattop.pl
SOUTH KOREA
Promat International
(Asia Pacific) Ltd.
SPAIN
Promat Ibrica S.A.
C/Velazquez, 47 - 6 izda
28001 Madrid
Tel: +34 91 781 1550
Fax: +34 91 575 1597
Email: info@promat.es
www.promat.es
SWITZERLAND
Promat AG
Stationsstrasse 1
8545 Rickenbach-Sulz
Tel: +41 52 320 9400
Fax: +41 52 320 9402
Email: office@promat.ch
www.promat.ch
UNITED KINGDOM
Promat UK Ltd.
USA
Promat Inc.