Professional Documents
Culture Documents
By makeiteasy
Disclaimer: This document is intend to show the way how to unlock a Huawei EC150 USB
Modem / or a CDMA Mobile device. Methods presented here are tested on a specific models and
wont work or no need to work on all models. Do the unlocking process at your own risk. I am
not responsible for any damage cause to the device or loss.
For unlocking Huawei EC150 youll need the following Tools & Softwares:
1. DFS 3.3.0.7 - CDMA Reprogram, flashing software.(www.cdmatool.com)
2. IDM UltraEdit v.17.0.XXX (www.ultraedit.com)
3. EC150Update_11.104.04.00.114.B416.exe Firmware Update (Incase you need to update
the firmware, Not necessary if you dont want to update)
4. CDMA Workshop 2.7.rar Reprogram, Flashing (www.cdma-ware.com) (www.filecrop.com)
5. EC150 Drivers (to install the device without operators dashboard)
6. Mobile_Partner_11.302.09.01.539_Voice_USSD Dashboard for setting up the connection.
Preface: The Standard freeware and tools that available on the internet wont work on this
device because this device has no IMEI Number instead of that it has a MEID number. So you
cannot calculate the unlock code based on an MEID. The Standard methods presented for
Huawei USB Modems wont work on this device. You cannot able to update the firmware without
SPC Code. So I hereby presented the other way used to read the code from the memory dump.
Fig 1.1
Note: Normally EC150 will connect to the system by using the following 3 COM Ports.
a. Modem Device
b. Application Interface
c. PC UI Interface (this one is used to run the operators application.)
We are not going to use the PC UI Interface port here to unlock the device.
5. Install DFS 3.3.0.7 on your PC and disconnect your Internet connection. (If any)
Because the DFS 3.3.0.7 checks for an online account, there is no need to run the DFS
online and the demo mode is enough for this process.
Fig 1.2 The DFS User Interface without connecting any device
to detect the
1.2. After that you see a connection icon to connect or disconnect a specific port. Mouse Roll
or Double click on the port you want to connect.
1.3. Below that you see a button named SPC
& send SPC codes to the device.
used to type
1.5.
1.7. On the Right side of the application window you see Reset icon which is used to
change the mode of the device.
a. Offline D Device is offline Dead mode
b. Offline A Device is offline Active Mode
c. Reset Device will disconnect and will automatically connect again.
d. FTM File Transfer Mode (for CDMA Mobile phones)
e. Radio on Turn on Radio Frequency
f. Radio off - Turn off Radio Frequency
g. Power off Device will shutdown (Unplug the device and Plug it Again)
h. Data Mode Device will go online.
i. Rebuild Restore Device to Factory Settings.
1.8.
You can see various Tabs that used to READ, WRITE and Reprogram the Device
1.9.
On below of the application you see a message box which shows you the response of
the device & ports.
1.10. After Connecting a port the software will try to retrieve the device information and
show it to you on the front panel.
6. Connect the Huawei Mobile Connect - Application Interface Port (See Fig 1.3)
7. Go to Memory Tab and change the Type to CEFS and press Read. The Software started
to read the memory
8. Send a false code (any six digits) to the Device by using the SPC Button.
9. The device will show you an error BAD SPC UNLOCK FAILED and the device will go to
offline for few seconds. During this period the software will read the SPC Code.
10. Immediately Press the Save Buffer Button. (Choose a path to save that memory dump
file)
11. Save that dump file to your hard disk. Most of the case the file size should be 228 KB
12. Open the file with data analyzer and press Analyze
13. Now the Data Analyzer will analyze the data and show you the Results in the result text
box. Youll see the contents in the Data monitoring page.
14. Click on SPC1 and press the memory address listed right to the SPC1.
Fig (1.3)
15. The first six digits is the SPC code of your USB Modem. Note down the ASCII Value.
16. Type it on the SPC and send it to the device (See fig 1.4)
Fig 1.4
17. Now you see the DEVICE UNLOCKED Message on the bottom of the message box.
Now youre Done Unlocking the device. Reprogram the device with other tabs presented on
the software.
3. The six digit hexadecimal value next to this string is the SPC code. (See fig 2.1)
Fig 2.1
ENJOY SURFING!!!