Tasues
€ > @ Ai www.gowelding.com/wp/asme-multihtm
toes SE HowWelgeuito of Petonlzarinks ) Windons ) Wandowe Meds (3 lnporado dolE C) Fabiation Welk. C) Nove guia
Approximate deposit thickness of each pracess should be recoreed OW/200,2
T= 2610
CMAN, orn [== (Gta) = én
ag [aa *{Snom)= 200m
Base Metal approval range for the above welded joint is 4.76mm To 52mm Ref QW451.1
Ifthe joint is made of more than one welding process then the maximum deposited thickness each process in the above
‘example is (2 x Deposited Weld Metal t):» GTAW 12mm and SMAW 52mm (This is because t= T for this process as
t> 19.4mm QW451.1)
Ifthe SMAW deposit in the above qualification was less than 19.1mm, assume 18mm and GTAW 8mm then to weld a
joint 52mm thick with 8mm GTAW and 44mm SMAW is not permitted as maximum SMAW deposit would be 36mm.
‘You can delete the SMAW and qualify an all GTAW weld 4.76 mm To 12mm thick or delete the GTAW and weld SMAW
4.7mm to 52mm thick, providing all the essential, non essential and supplementary variables are applied to the WPS.
(Note the procedure allows the SMAW to be used as a rot run but not the welder qualification.)
When tested the deposited weld metal of each process must be included in the tension and bend test specimens and
impacts where applicable. Note itis acceptable for the impact test for the GTAW to contain some SMAW in the test
specimen.€ > @ Ai www.gowelding.com/wp/asme-multihtm
toes SE HowWelgeuito of Petonlzarinks ) Windons ) Wandowe Meds (3 lnporado dolE C) Fabiation Welk. C) Nove guia
PICK and MIX QW200.4 b [Note restrictions in QW451.1 notes (1)]
This applies to test coupons 13mm and thicker and welding processes SMAW, SAW, GTAW, GMAW. A WPS.
consisting of several processes can be created from different POR’s, but the maximum thickness of base metal covered
by this WPS can't exceed 2 x the thickness of the thinnest test coupon used for each PQR and each process can't
exceed 2 x its deposited thickness. This applies even if all the processes used for that coupon are not required in this
WPS. However the base metal thickness of the POR used for the root does not have to be considered ifthe WPS is
single sided QW200.4 b
Note test coupons 38mm and above approve deposited weld metal and also base metal thickness up to 200mm max
QW451.1. (QW403,7 Processe GTAW,SMAW,GMAW,SAW)
canes
Coe So (Sa
Can the proposed POR be made from the above example + POR 2 + POR 3.
Consider individual deposited thi 2xt
GTAW 12mm > 6mm. SMAW 80mm > 38mm, GMAW 6mm > 20mm All OK
Consider Plate thickness 2x
Hi asweswesoeMop — ~ hiosaciodes os downoatn€ 2 @ Ai wwwngowelding.com/wp/asme-multihtm
tops BE Howl gauito ss Peonalarinks [) Windows O) Wadows Meis (2 Inporado dE) Fabcation Welds.) Nowa guia
Note test coupons 38mm and above approve deposited weld metal and also base metal thickness up to 2UUmm max
QW451.1. (QW403.7 Processe GTAW,SMAW,GMAW,SAW)
Ceo Ceo Se
Can the proposed PQR be made from the above example + PR 2 + POR 3.
Consider indi aed thi
GTAW 12mm > 6mm. SMAV 60mm > 38mm. GMAW 66mm > 20mm All OK
Consider Plate thickness 2x T
SMAW 60mm <65mm Fail. GMAW 66mm > 65mm OK. GTAW not considered.
‘SMAW procedure can't be used for proposed PAR
Ifyou want to weld a 30mm plate and your welder qualifications only go up to 15mm use two welders. You can't use
‘one welder with two different qualifications for the same process
+ Back
Hi asweswesoeMop — ~ hiosaciodes os downoatn