Professional Documents
Culture Documents
Power Supply PWM Supervisor: Esquiloesperto
Power Supply PWM Supervisor: Esquiloesperto
Esquiloesperto
(Messias-BH.)
ATX 2005
POWER SUPPLY PWM SUPERVISOR
Power Supply Pulse Width Modulation Integrated Circuit Controller
Specs
(English version)
version 1.0
April, 2012
ATX 2005
Specification: v-1.0
Page 02
General Description
The integrated circuit ATX-2005 is a pulse width modulation (PWM) controller, which can be used in the
power supplies' secondary side, ready to provide the total voltage and load switching control.
ATX-2005 has all inside functions for protection and control, undervoltage/overvoltage detection, output
voltage status monitor (PG), external remote control (REM)... and more.
The ATX-2005 is able to set the power supply's behavior in order to reduce the external devices usage to
get required control. The undervoltage (UVP) and overvoltage (OVP) modules assist the 3.3V, 5V, and
12V voltage levels. The PP function is set to monitor power and negative voltages, and a built-in shunt
regulator module (the 431 shunt regulator) is built to make the PWM's correct level control, providing a
stable output voltage through a group of amplifiers that monitor the feedback pattern. Besides, the antinoise filter prevents malfunction caused by outer interference.
Features
RI External resistor to settle down the internal reference current, noise immunity and delay time
protection
Built-in shunt regulator to provide stable output voltage (431 Shunt Regulator)
Pin Assignment
ATX 2005
Specification: v-1.0
Page 03
Pinning
Pin
Symbol
Function
Description
VCC
Source
REM
Input
V3.3
Input
V5
Input
5V voltage monitor
PP
Input
V12
Input
O1
Output
O2
Output
PG
Output
10
FB
Output
11
VREF
Input
12
GND
Ground
13
COMP
Output
14
NEG
Input
15
SS
Input
16
RI
Input
Limiting Values
Item
Supply
voltage
Power
dissaption
Operating
temperature
Storage
temperature
Symbol
Conditions
Min.
Typ.
Max.
Unit
VCC
4,5
5,5
Pd
--
1000
--
mW
-10
--
+70
-65
--
+150
ATX 2005
Specification: v-1.0
Page 04
Electrical Characteristics
TA temperature = 25 C, main voltage VCC = 5V
Voltage protection levels (V33, V5, V12, PP)
Item
Overvoltage
Protection
Undervoltage
Protection
Undervoltage
Detection
Undervoltage
Delay Time
Symbol
Conditions
Min.
Typ.
Max.
Unit
V33
V5
V12
PP
V33
V5
V12
V33
V5
V12
PG low
PG low
PG low
PG low
PG low
PG low
PG low
PG low
PG low
PG low
3.9
5.6
13.4
2.3
2.0
3.0
5.9
2.6
4.1
9.6
4.1
6.0
14.0
2.6
2.4
3.6
7.1
2.9
4.45
10.3
4.4
6.4
14.4
2.8
---3.1
4.7
10.7
V
V
V
V
V
V
V
V
V
V
Td1
Remon On/Off
150
250
350
ms
Symbol
Conditions
Min.
VIH
---
1.8
VIL
---
tdb-rem
---
tdb-remoff
---
22
Typ.
Max.
Unit
V
28
0.8
34
ms
ms
Symbol
Conditions
Min.
Typ.
Max.
Unit
ILEAKAGE
Output = 5v
--
--
uA
DCmax
Duty cycle
(max.)
84
--
93
Symbol
Conditions
Min.
Typ.
Max.
Unit
IPGL
PG=5V
--
--
uA
Td
--
100
220
400
ms
VOL
IPGO=10mA
--
0.2
0.4
ATX 2005
Specification: v-1.0
Page 05
Shunt Regulator (VREF FB)
Item
Reference voltage
for Shunt Reg.
Output Sink
Current
Symbol
Conditions
Min.
Typ.
Max.
Unit
VREF
IFB = 0.5mA
2.45
2.50
2.55
IOUT
VFB > 3V
10
--
--
mA
Min.
Typ.
Max.
Unit
Symbol
Conditions
--
0.5V~3.5V
--
0 dB
Item
Symbol
Conditions
Min.
Typ.
Max.
Unit
Soft Start
charge current
ICH
RI=75K
8.0
9.5
11.0
Close Loop
Voltage gain
Cross over
crossing point
--
65
--
310
--
dB
--
KHZ
Soft-start (SS,RI)
Reference:
Internal Control Circuit Diagram
ATX 2005
Specification: v-1.0
Page 06
Package Outline