Professional Documents
Culture Documents
Irvine, CA 92618
USA
VertX
December 2010
Document Number: 6080-901 Rev G.2
Contents
Introduction
............................................................................................................................................ 3
............................................................................................................................................ 5
Step 1 Connect........................................................................................................................................... 6
1.1
1.2
1.3
Mounting Instructions.......................................................................................................... 6
1.4
1.5
Wiring VertX........................................................................................................................ 7
1.6
Modem .............................................................................................................................. 12
1.6.1
1.6.2
Step 2 Contact.......................................................................................................................................... 13
2.1
2.2
Installation......................................................................................................................... 13
Use ................................................................................................................................... 14
17
Trouble-shooting ............................................................................................................................ 17
System Status ................................................................................................................................. 17
Supplemental Configuration ............................................................................................................ 17
Configure......................................................................................................................................... 17
System Time ................................................................................................................................... 17
Update System................................................................................................................................ 17
Network Defaults Jumper ................................................................................................................ 18
Firewall .......................................................................................................................................... 18
Contact Information.................................................................................................................................. 19
Regulatory
.......................................................................................................................................... 20
December 2010
Page 2 of 24
Introduction
HIDs VertX open platform is flexible and scalable to permit economic and high performance access control
solutions for a wide range of applications. The VertX units interconnect through different sub-networks and
protocols to a standard TCP/IP network with the capability of a variety of applications.
For example, the VertX Access Controllers are a cost-effective method for two-way communication using
Ethernet between a computer and a V1000 or V2000. In addition, the V1000 can communicate through a
RS-232 serial port and a multi-drop RS-485.
Parts List
Description
Quantity
1 V2000
or
1 V1000 and
any combination of
(up to 32) interface
panels.
- Mounting screws
8 ea V1000/V2000
4 ea V100-Series
Note: One or more VertX Interface panels are required when installing a V1000 controller.
Note: A modem and RS-232 Serial modem cable must be purchased separately, if your installation includes a
modem.
Product Specifications
Description
Specification
Power Supply
12-16VDC
1 Amp
V1000 -210mA
V2000 - 625mA (with two R40 iCLASS Readers)
V100 - 450mA (with two R40 iCLASS Readers)
V200 - 60mA
V300 - 75mA
32-122F (0-50C)
Humidity
5% to 95% non-condensing
December 2010
Page 3 of 24
Cable Specifications
Cable Type
Length
Specification
RS-485 *
RS-232
Input Circuits *
Output Circuits *
Wiegand
Ethernet
Power Supply
+12 VDC IN
----
December 2010
Page 4 of 24
Overview
The following outlines what is required to install VertX controllers and panels.
December 2010
Page 5 of 24
Step 1 Connect
1.1
1.2
V1000 or V2000
1. Verify the battery jumper is installed in the ON position
(or OUT position on old covers), P15 connector
(V1000).
2. If installing a V1000 - Verify the termination jumper is in
the Out position when there are no panels attached to
the port. If there are downstream interface panels
attached then the termination jumper should be in the In
position. The V1000 is shipped with jumpers in the Out
positions
1.3
Mounting Instructions
1. The controllers and interface panels should always be
mounted in a secure area.
2. Mount using the four mounting screws (provided) or
other appropriate fasteners. Place the fasteners in the
corner holes of the base.
3. The VertX devices can be stacked with or without the cover. Do not remove the plastic base. Make
sure you position the VertX devices in such a way as to provide room for wiring, air-flow and cable
runs.
1.4
Terminating
Jumper
December 2010
Page 6 of 24
1.5
Wiring VertX
CAUTION: Connectors on the VertX devices are positioned to be mirror images and are not
interchangeable once the installation is complete. Therefore, you cannot unplug a
connector from one side and plug it into the corresponding connector on the other side.
1. Network Connection: Connect the VertX V1000/V2000 to the network using a standard Cat5
network patch cable. Connect one end of the Cat5 network patch cable to the J1 (RJ-45) connector
on the V1000/V2000 and the other end to the network connection point (network jack, hub, switch,
or router) on your site.
2. Serial (RS-232) Adapter cable (P/N 70007)
The Serial Adapter cable is a six inch adapter that converts the 9 pin MTA header to a standard DB-9 male
connector. This adapter is to be utilized for attaching a standard RS-232 serial modem cable (not included)
to the VertX controller. This will allow one of the approved external modems (listed in 1.6.1 Modem Setup
Requirements, page 12) to be attached to the VertX V1000.
The table shows the P17 pin settings.
Pin #
P17
DCD
RX
TX
DTR
GND
DSR
RTS
CTS
RI
3. Power and Alarm input connections (All VertX units): Connect power by providing 12VDC to the
P7 connector. +12VDC goes to Pin 1 and ground to Pin 2. Batt
Pin #
P7
Fail, AC Fail, and Tamper switch inputs are wired as shown in
the table. Connect the Bat Fail and AC Fail inputs to battery
1
+12VDC
low/failure and AC failure contacts provided on the power
2
Ground
supply. Connect the Tamper input to a tamper switch on the
enclosure.
3
Bat Fail 4
Bat Fail +
AC Fail -
AC Fail +
Tamper -
Tamper +
December 2010
Page 7 of 24
Pin #
P1
P4
Reader Power
Shield Ground
Ground
Hold
Data 0 / Data
Beeper
Data 1 / Clock
Red LED
Data Return
Green LED
Green LED
Data Return
Red LED
Data 1 / Clock
Beeper
Data 0 / Data
Hold
Ground
10
Shield Ground
Reader Power
PCB
Pin #
V1000 P3
V1000 P4
(port 1 and 2)
PCB
Pin #
Not in use
Not in use
Shield
Shield
Not in use
Not in use
Not in use
Not in use
Shield
Shield
Not in use
10
Not in use
10
(port 3 and 4)
CAUTION: The V1000 RS-485 Ports 1 & 2 (P1) are a common bus and therefore cannot have
panels with duplicate Interface Addresses assigned. The same is true of the V1000 RS-485,
Ports 3 & 4 (P4). For example, two panels, both with Interface Address 0 (factory default),
cannot be connected to Ports 1 and/or 2 (P1).
December 2010
Page 8 of 24
It is recommended to wire the RS-485 to the In position of the P9 terminal block of the V100-Series
panel. This is especially important when the RS-485 communication is in a daisy chain
configuration. If the RS-485 is wired In and Out, and power is lost, or the P9 terminal block is
unplugged on a V100-Series panel, RS-485 communications will be lost to downstream V100-Series
panels.
Output
number
V2000
V1000
P3 Pins 1/2/3
1
Strike(lock)
Relay 1
P3 Pins 4/5/6
Aux Relay 1
V100
V200
V300
P3 Pins 2/3/4
P1 Pins 1/2/3
P6 Pins 3/2/1
P1 Pins 4/5/6
P3 Pins 1/2/3
P14 Pins 3/4/5
Strike (lock)
Relay 1
P3 Pins 4/5/6
Aux Relay 1
P6 Pins 6/5/4
P6 Pins 6/5/4
Strike (lock)
Relay 2
Strike (lock)
Relay 2
P6 Pins 3/2/1
P6 Pins 3/2/1
Aux Relay 2
Aux Relay 2
December 2010
P1 Pins 7/8/9
P2 Pins 1/2/3
Page 9 of 24
Output
number
V2000
V1000
V100
V200
V300
P2 Pins 4/5/6
P2 Pins 7/8/9
P4 Pins 9/8/7
P4 Pins 6/5/4
P4 Pins 3/2/1
10
P5 Pins 9/8/7
11
P5 Pins 6/5/4
12
P5 Pins 3/2/1
CAUTION: Some magnetic locks exhibit both high inrush current when activated and a high
instantaneous break voltage when de-energized due to magnetic field collapse. It is
recommended you use of a snubber circuit across the controlling relay terminals to protect the
controlling relay contacts. Go to support.hidglobal.com, see Solution 891 - How do I wire a High
In-Rush Current locking device to VertX/Edge/Edge Solo?.
8. Input Connections (All VertX devices) Input connections are analog inputs used for a combination of
specific functions such as Request-to-Exit (REX), Door monitor, etc. They can also be used as general
purpose monitoring. Connect one side of the switch or contact to the + (plus) lead and the other to the
(minus) lead. The following table shows where the inputs are located. Pin numbers shown on the cover
use the convention +/.
The default REX input configuration is normally open (NO) unsupervised (no EOL resistors).
However, the default door switch (DS) configuration is Normally Closed (NC), unsupervised (no
EOL resistors).
All other input points are defaulted for NO switches and are unsupervised (no EOL resistors).
Configure any input as NO or NC, as well as unsupervised or supervised. They can be configured for
supervisory resistors of 1K 6K Ohm. The setup of supervised inputs should be done during configuration
of the VertX devices via the host
Example: Input 1, V1000 is: P14 Pin1 is + and Pin 2 is -.
December 2010
Page 10 of 24
Input
number
1
2
3
4
5
6
7
V2000
V1000
P2 Pins 1/2
Door Monitor
P2 Pins 3/4
REX input
V100
P2 Pins 1/2
Door Monitor
P2 Pins 3/4
REX input
P5 Pins 4/3
P7 Pins 8/7
P5 Pins 4/3
Door Monitor
Tamper
Door Monitor
P5 Pins 2/1
P7 Pins 6/5
P5 Pins 2/1
Rex Input
AC Fail
Rex Input
P7 Pins 8/7
P7 Pins 4/3
P7 Pins 8/7
Tamper
Batt Fail
Tamper
P7 Pins 6/5
P7 Pins 6/5
AC Fail
AC Fail
P7 Pins 4/3
P7 Pins 4/3
Batt Fail
Batt Fail
V200
V300
P1 Pins 1/2
P6 Pins 2/1
P1 Pins 3/4
P3 Pins 1/2
P1 Pins 5/6
P1 Pins 7/8
P1 Pins 9/10
AC Fail
P7 Pins 4/3
P2 Pins 3/4
P4 Pins 10/9
10
P4 Pins 8/7
11
P4 Pins 6/5
12
P4 Pins 4/3
13
P4 Pins 2/1
14
P5 Pins 6/5
15
P5 Pins 4/3
16
P5 Pins 2/1
19
P7 Pins 6/5
P2 Pins 1/2
P2 Pins 5/6
18
Tamper
Batt Fail
17
P7 Pins 8/7
P7 Pins 8/7
Tamper
P7 Pins 6/5
AC Fail
P7 Pins 4/3
Batt Fail
December 2010
Page 11 of 24
1.6
Modem
The VertX controller will automatically answer incoming calls when an external serial modem is attached to
the RS-232 port 1.
1.6.1
External Modem (not included). The modem must be selected from the following approved HID modem
list:
o Zoom V.90 56 K Fax Modem, Model 2949 (external modem uses phone jack)
o U.S. Robotics V.92 56K Fax Modem, Model 5686 (external modem uses phone jack)
o Telular GSM 850/1900, Model 1C02A160 (external cellular modem)
1.6.2
December 2010
Page 12 of 24
Step 2 Contact
Contact the VertX controller through two methods.
2.1
Virtual Port
Discovery Client
The Discovery Client provides a technician with a method of locating all of the VertX controllers that are
connected to a network. Controller information is displayed providing the ability to blink the VertX controller
Comm LED and configure the unit by launching a browser pointed at the Configuration GUI of the targeted
controller. When the Discovery Client is launched, a discover command is issued and the Configuration GUI
screen is populated with the results. Also provided is the ability to refresh the Configuration GUI screen on
command.
Use this feature when the VertX controllers and network have been installed and are operational, but before the
VertX controller(s) has been configured. At this point, all of the controllers on a network will have the same host
name and unknown IP addresses (assuming a DHCP environment). In this scenario, the only mechanism
available to configure a controller is the serial debug port or by only placing one controller on the network at a
time. The Discovery Client provides an easy to use mechanism to configure controllers.
2.1.1
Installation
An operating system of Windows XP with .NET Framework v2.0 installed is a requirement for the Discovery
Client to function properly.
1. The Discovery Client can be downloaded by placing the following path in an Internet browser.
http://www.hidcorp.com/downloads/DiscoveryClient.zip
2. The File Download dialog will display, click Open
3. When the contents of the zip file display, double-click setup.exe
4. If a security warning is received, click Run
5. From the Discovery Client Welcome page, click Next
6. Select the Installation folder and who should have access to the Discovery Client, click Next
7. Confirm the installation location, click Next
8. Click Close
December 2010
Page 13 of 24
2.1.2
Use
The following provides information on how to access and use the Discovery Client.
1. Enable VertX controllers on the network
2. Click Start > Programs > VertX Tool Box > Discovery GUI to access the Discovery Client
3. Returned is a list of controllers attached to the network. If there is more than one controller listed,
controllers can be identified using the MAC Address label on the unit
4. If unsure of a controllers physical location click Blink ON to start the Comm LED blinking on the
controller. Note the name on the button will change to Blink OFF. When verification of the controller
is complete, click Blink OFF
5. Click Configure Unit to open the Basic Configuration page of that controller
6. Go to Step 3 Configure, page 15
2.2
Virtual Port
Contact a VertX controller by directly connecting the computer to the controller using an Ethernet cable. By
default, every controller is configured to respond to a fixed address: 169.254.242.121.
1. Ensure you are running a Windows 2000 or XP computer
2. Disconnect your Windows computer from its hub or network
3. Connect the Windows computer to the controller with an Ethernet cable
4
5. Enter ipconfig /renew -- wait for DHCP to timeout (approximately 60 sec). The computer will
acquire a 169.254.x.x address
6. Access a web browser and enter 169.254.242.121 into the Address field. The controller is now
accessible through this Virtual Port
December 2010
Page 14 of 24
Step 3 Configure
This section describes the communications configuration that enables the controller to communicate with the
host software.
There are three methods of communication possible on a V1000 controller:
Dynamic Host Configuration Protocol (DHCP) TCP/IP Addressing
Static TCP/IP Addressing (see Configuration Checklist, page 21 for a list of criterion needed for a Static
TCP/IP configuration)
Modem (see Configuration Checklist, page 21 for a list of criterion needed for a modem configuration)
Enter only the configuration that relates to your sites specific installation.
3.1
VertX Communications
The VertX communications configuration is provided through a browser-based application called the
Configuration GUI (Graphic User Interface).
3.1.1
3.1.2
Select the Connection Selection radio button to establish your systems specific communication type.
Choices include:
Network
Modem
December 2010
Page 15 of 24
3.1.3
Enter the Host Name, and the Here I Am Interval collected on the Configuration Checklist, page 21.
3.1.3.1
Controller Login Password
During your first instance of accessing the Configuration GUI, you must change the password (located at the
bottom of the screen). Enter a new password, and reenter the password in the second field.
Note: This step is not necessary during any consecutive Configuration GUI sessions. However on consecutive
sessions the password may be changed.
Once configuration changes have been made, click Submit, and the Confirmation page (see 3.1.4
Confirmation, page 16) will display.
3.1.4
Confirmation
Once configuration changes are complete and submitted, the Confirmation screen will display. Verify that the
changes submitted are accurate, and click Save. If the changes submitted are not accurate, click Cancel and
adjust the settings appropriately.
Step 4 Communicate
Now that the controller is connected, contacted and configured, contact the host to test the system.
December 2010
Page 16 of 24
Appendices
Trouble-shooting
System Status
System Status provides a technician with a method of validating the VertX installation, field wiring and installed
devices. Perform the System Status at any time after the VertX controller has been installed and power is
available. In addition, a technician may perform a system status as many times as necessary.
Upon startup, the System Status page will discover all connected and powered V100-Series devices attached
to the controller and displays the inputs, outputs, and host status.
Reference the Legend to determine the meaning of the different images.
By clicking Add Unconfigured you can configure the V1000 for the attached panels and readers. The
assumption is that two readers are attached to any V100 interface panel and that both readers are Wiegand
card only. Once the configuration is complete, the VertX software will refresh.
Once the page refreshes, a Restore Previous button becomes available.
The Restore Previous button enables the technician to use the previously saved configuration.
Supplemental Configuration
Supplemental Configuration provides the ability to view and configure system inputs and outputs
These buttons provide navigation to the following functionality:
Configure - configure inputs, outputs and door characteristics for a V1000, V100, V200, and V300
System Time - update System Time
Update System updates the interface boards firmware
Configure
Configure provides the ability to view and modify system inputs and outputs and door characteristics.
Upon successful validation, the Save button will write modified values to the interface board.
System Time
System Time provides the ability to view and set the date, time, and time zone values on the controller.
Upon initialization, Date, Time, Time Zone and TZ fields will be populated with the current system settings. The
date displayed (non-text box) will be updated approximately every 30 seconds.
The Time Zone field provides a drop-down menu. One of the options in the Time Zone drop-down menu is
Custom Time Zone. If Custom Time Zone is selected, the TZ text box will be enabled. Otherwise, the TZ is
associated with the Time Zone field.
Update System
Update System allows the user to update the firmware on the interface board. During a download the interface
board image flashes between grey and yellow. When a download completes the image color changes to green
for successful or red for failure. If the download fails, a tool tip with the error status code may be viewed by
hovering the mouse over the image in question.
Initially, all of the interface boards will be selected for a download to commence.
Note: Depending on the VertX controller and system, it may take several minutes to completely download.
December 2010
Page 17 of 24
1. Place a jumper over the right two pins of the P9 debug port.
2. Reboot the controller to change all of the network configuration settings back to the factory defaults.
3. After the LED turns amber, remove the jumper from the P9 debug port. Upon removing the jumper it
takes approximately 60 seconds for the controller to reset. Once the reset is complete, the LED will
return to green.
CAUTION: During the process of rebooting the controller, all network configuration information will
be overwritten and returned to the original defaults.
4. Configure the controller for your installation parameters. See 3.1 VertX Communications, page 15.
Firewall
If the VertX controller is being installed where it communicates through a firewall, then the firewall may need to
be configured to allow TCP data transfer on the specified port(s).
1. Before starting, ensure that any pop-up blocker software is disabled on the computer.
2. Open the following ports on the firewall.
connection_port(4070)TCP outbound.This port must be open on the Host computer.
CAUTION: If the firewall is not configured properly the controller may not communicate with the host.
December 2010
Page 18 of 24
Contact Information
Americas
HID Global (California, USA)
support: support_na@hidvertx.com
sales: sales@hidvertx.com
main: (949) 598-1600
sales: (800) 210-4744
telephone: 1-800-237-7769
fax number: (949) 598-1690
Asia-Pacific
HID Asia Pacific Ltd. (Hong Kong)
support: support_APAC@hidvertx.com
sales: salesapac@hidvertx.com
telephone:
(852) 3160 9802
fax number: (852) 3160 4809
December 2010
Page 19 of 24
Regulatory
December 2010
Page 20 of 24
Phone Number
IT contact
Sales / PM
Hardware
Name
Source
Part Number
Ethernet Cable
Computer with Web Browser
Hub (Optional)
Modem (Optional)
VertX Modem Cable (Optional)
HID
70007
VertX IP Address
Subnet Mask
Default Gateway
Network Broadcast
Domain Name
VertX Host Name
FTP Enabled
Yes
No
Telnet Enabled
Yes
No
Yes
No
OR
OR
or
.
2
.
December 2010
Page 21 of 24
Intentional Blank
December 2010
Page 22 of 24
Contact:
Installed Location:
MAC Address:
Modem Model:
RS232 Port #:
Hostname:
IP Address:
Tamper:
Input 1:
AC Fail:
Input 2:
Phone #:
BATT Fail:
Relay 1:
Relay 2:
Interface
Interface
Interface
Reader
Monitor
Control
V300 Output
V200 Input
V100 Door /
Tamper:
AC Fail:
Reader 1:
BATT Fail:
Reader 2:
Door Switch 1:
REX 1:
Door Switch 2:
REX 2
Strike Relay 1:
Aux Relay 1:
Strike Relay 2:
Aux Relay 2:
Input 1:
Input 2:
Input 3:
Input 4:
Input 5:
Input 6:
Input 7:
Input 8:
Input 9:
Input 10:
Input 11:
Input 12:
Input 13:
Input 14:
Input 15:
Input 16:
Relay 1:
Relay 2:
Relay 1:
Relay 2:
Relay 3:
Relay 4:
Relay 5:
Relay 6:
Relay 7:
Relay 8:
Relay 9:
Relay 10:
Relay 11:
Relay 12:
Input 1:
Input 2:
December 2010
Page A1
2003 - 2010 HID Corporation. All rights reserved.
Interface
Interface
Interface
Reader
Monitor
Control
V300 Output
V200 Input
V100 Door /
Tamper:
AC Fail:
Reader 1:
BATT Fail:
Reader 2:
Door Switch 1:
REX 1:
Door Switch 2:
REX 2
Strike Relay 1:
Aux Relay 1:
Strike Relay 2:
Aux Relay 2:
Input 1:
Input 2:
Input 3:
Input 4:
Input 5:
Input 6:
Input 7:
Input 8:
Input 9:
Input 10:
Input 11:
Input 12:
Input 13:
Input 14:
Input 15:
Input 16:
Relay 1:
Relay 2:
Relay 1:
Relay 2:
Relay 3:
Relay 4:
Relay 5:
Relay 6:
Relay 7:
Relay 8:
Relay 9:
Relay 10:
Relay 11:
Relay 12:
Input 1:
Input 2:
December 2010
Page A2
2003 - 2010 HID Corporation. All rights reserved.