APC-1-410L
FabriPulse’
Model B
Pulse-Jet Fabric
Dust Collector
elFabriPulse’
Fabric Dust Collectors...The Problem Solvers
FabriPulse pulse-jet fabric dust
collectors are used by industry
throughout the world to remove
particulate from process and general
ventilation air as well as to recover
valuable resources from many
manufacturing processes. As a
standard of the industry, FabriPulse
FabriPulse Assembly
dust collectors have long been
one of the most diverse product
lines available for air pollution
control. The Model B FabriPulse
collector adds a new dimension of
versatility, allowing you to select the
best size and design to solve your
dust control problem.
TWO INLET CHOICES FOR
OPTIMUM CLEANING
EFFICIENCY
The Model B FabriPulse collector
design offers either top entry or
hopper entry to meet the needs of
your particular applications.
For a fine dust (such as talc), on
applications with light dust concen-
trations and with higher air-to-cloth
ratios, top entry is the proven
method. Pioneered by AAF, top
entry generates a downtlow of air
throughout the collector. Because
the air flow is downward, it aids
rather than impedes the migration of
fine particulate towards the hopper.
For both methods of entry, precise
baffling in the Model B FabriPulse
collector helps distribute air evenly
throughout the unit for maximum
leaning efficiency of each bag.
cut-away View of Hoppa nat
For applications with a heavy,
coarse dust (such as sand) and high
dust loads which require air-to-cloth
ratios of 6:1 or less, hopper entry is
the usual choice, Heavy particulate
in the lower velocity air stream
associated with low air-to-cloth ratios
naturally gravitates to the hopper.oO
Pulse-Jet Cleaning for Effective Fabric Reconditioning
The filter bags in the FabriPulse dust
collector are reconditioned with
pulses of compressed air which are
initiated by either a solid-state
electronic timer or an electronic
differential pressure switch. Small
bursts of high pressure air are directed
from the surge tank through the
Pulse pipe and exit the pulse pipe
orifices as jets of air at sonic
velocity. The jet of air expands as it
travels from the ortice to the venturi,
inducing more cleaning air into the
jet stream. The venturi acis to seal
the top of the bag, allowing a shock
wave to form and travel to the
bottom of the bag. Horizontal
pressure is formed inside the bag,
expanding the fabric and dislodging
the dust from the outside of the bag.
The bag receives a secondary
cleaning as the pulse of air bounces
back up in the bag. Pulse-jet
cleaning provides effective on-line
reconditioning of the fabric without
interrupting the air flow through the
collector. Since pulse-jet collectors
operate at higher filtering velocities,
they are much smaller than
corresponding fabric collectors which
are cleaned by either mechanical
shaking or low pressure reverse air.
Poeun cs
sng a2 rade
ites rare ois Berry, arg
Feary
wt
ie
sera FeConstructed For Lower Cost Installation and Maintenance
MODULAR CONSTRUCTION
The Model B FabriPulse dust
collector features modular con
struction consisting of a top plenum,
housing and hopper section. The
top plenum contains the tube sheet
with its pulse-cleaning system and is
manufactured to precise quality and
‘engineering standards.
To minimize leakage, housings and
hoppers feature all-welded construc-
tion 12 gauge or heavier reinforced
steel plate. For smaller sizes the
housing and hopper may be ordered
as a single welded subassembly.
On large sizes the housing and hop-
pers normally ship as separate mod-
ules that can be welded or bolted
together on-site.
MAINTENANCE EASE
Top access to filter bags and pulse
hardware makes servicing the
FabriPulse collector easy. Pulse
pipes, serving 12 bags per valve,
Pc
Exploded View of FabriPulse Components
Cut-Away View of FabriPulse
Collector interior
are joined to large pulse valves by a
quick disconnect device and can be
readily removed. The venturi and
cage form an integral assembly
requiring no tools for removal.
CONVENIENT BAG
REMOVAL
‘The FabriPulse collector bag sealing
method utilizes a collapsible stain-
less steel patented Snap-Band sewn
into the end of the filter bag for easy
insertion and removal. The bag is,
removed by collapsing the snap-band
and lifting the bag out of the tube
sheet. Replacement is done easily
‘Bag, Cage and Venturi Assembly
by suspending the bag through the
tube sheet opening. Then collapse
the snap-band and insert it into the
tube sheet, allowing it to expand into
position. Slide the cage and venturi
assembly down into the bag.Broad Choice of Standard Options
HOPPERS
The FabriPulse collector is available
with all-welded pyramid hoppers on
all sizes and designs. A trough
hopper is available on size 132
and larger.
LEG EXTENSIONS
Standard leg height provides a 4 tt.
clearance from the hopper outlet to
the base.
Leg extensions in 6-inch increments
providing up to &-foot hopper clear-
ance are available.
NEMA 9 CONTROLS
Solenoid pilot boxes and control
panel with NEMA 9 rating are
available,
Technical Data
EQUIPMENT SIZE
12-48-770
Tota
square fet
otmecia
Number
tease
Bag
rena
RESISTANCE ACROSS
COLLECTOR
A fairly constant pressure drop
across the collector is maintained
because of the continuous cleaning
of the bags. The pressure drop will
vary with the velocity of air through
the media (or air-to-cloth ratio),
temperature of the gas stream, dust
loading, fineness and characteristics
of the dust, and the type of fabric
used. In most cases, pressure
drop will range from 3 inches to
7 inches, wg)
HIGH TEMPERATURE
CONSTRUCTION
For elevated gas temperatures, high
temperature gasketing and factory-
installed insulation are available.
EXPLOSION VENTS
Explosion vents for positive or nega~
tive pressure systems are available.
PRESSURE DEMAND
CONTROLS
Minimizes compressed air usage
and maximizes bag life by initiating
bag cleaning only when the pressure
drop across the bag-house reaches
a preset level
Explosion Vent
AIR-TO-CLOTH RATIO ‘Typleal Al-To-Cloth Ratios
‘The volume (CFM) per square foot ——
of fabric is a function of the quantity, ws noose
physical properties and chemical | | awnine a0
properties of the dust encountered. | | Seth “
Ratios normally will vary between | | trnen a
Sed Fonts, ran tos
COMPRESSED AIR tnsoiie a
REQUIREMENTS Postes 74
Normally only % to 1 SCFM of clean, en, ioe
dry, compressed air will be required | | Sou oeemens 2
for each 1,000 CFM of dust-laden =— one
ShyorGonr rons racmanser
air. The actual compressed air
requirements will vary with the dust
loading, air-to-cloth ratio, etc.
SIZING OF COLLECTOR (TYPICAL EXAMPLE) —
Application: Collection of coal dust generated by material handling conveyors.
Expected Inlet Dust Concentration : § grains/t?
Air Volume: 12,000 acim at 75°F db
Air-to-Cloth Ratio: Because the inlet dust loading is moderately heavy, we will
select an air-to-cloth ratio of 9:1 (3 fpm).
Required Cloth Area:
Gas Flow
Filtering Velocity ~
Equipment Selection: Based on the above, the proper selection would be a
12-84-1347 FabriPulse Collector with 1, 347 ft of cloth.
000
9 feimin
1,339 ft of cloth
5Other FabriPulse Dust Collector Designs
FabriPulse DESIGN P
FabriPulse Design P collector responds to the need to the convenience and efficiency of top-bag removal
protect maintenance personnel from severe weather from inside the protective plenum. Because the
conditions while servicing the dust collector. Guard-rails plenum serves as the clean-air outlet chamber, the
are replaced with a roof-top access plenum extending outlet duct can be cut into any side or into the top
over the top of the unit, affording maintenance personnel of the plenum.
FabriPulse DESIGN M
‘The FabriPulse Design M collector uses unique,
small diameter bags (with builtin venturis and
expanders) to pack a large fabric area into a very
small space. Unlike cartridge collectors, the
Design M collector normally operates at air-to-
cloth ratios of 3:1 to 10:1. The collector is
shipped fully factory-assembled with bags
installed on most sizes for fast, easy installation,
Factory pre-wiring, as shown, is optionalT)
Ise ASSEMBLY, MODEL B
FabriPul
(HOUSING INLEFabriPulse ASSEMBLY, MODEL B, DESIGN P (HOUSING INLET)
SnyderGenerel
In Canada, write: SnyderGeneral Canada, Ine.
For more information on
|AAF Air Pollution Control Products
Call 1-800-678-4356
{Ask for Department 1830 for the namo of
your nearest AAF Sales Representative
P.0.BOX 35690
6969 fanada Highway Suite 142 Bt. Laurer
LOUISVILLE, KENTUCKY 40232-5690
‘Quebec HAT 1V8