Professional Documents
Culture Documents
Acer x223w SG
Acer x223w SG
ACER_LCD_X223W_SM072301V1
Service
Model ID: R22ANUW-M1
Service Manual
Table of Contents
Important Safety Notice------------------------------------------------------------------------------------- 01
01. Product Specification--------------------------------------------------------------------------------- 02
02. OSD Menu-----------------------------------------------------------------------------------------------08
03. Exploded Diagram ------------------------------------------------------------------------------------- 10
04. Assembly and Disassembly Procedures-----------------------------------------------------------12
05. Troubleshooting----------------------------------------------------------------------------------------20
06. Schematics and Layouts------------------------------------------------------------------------------ 30
Published by LITE-ON Service Printed in Taiwan All rights reserved Subject to modification
23th-Jul-2007
ACER X223W
Go to cover page
Product Anouncement:
This product is certificated to meet RoHS Directive and
Qualified Repairability:
Proper service and repair is important to the safe,
reliable operation of all series products. The service
providers recommended by vender should being
aware of notices listed in this service manual in order
to minimize the risk of personal injury when perform
service procedures. Furtermore, the possibile existed
improper repairing method may damage equipment or
products. It is recommended that service engineers
should have repairing knowledge, experience, as well
as appropriate product training per new model before
performing the service procedures.
NOTICE:
! To avoid electrical shocks, the products should be
connect to an authorized power cord, and turn off the
master power switch each time before removing the
AC power cord.
! To prevent the product away from water or explosed
in extremely high humility environment.
! To ensure the continued reliability of this product,
use only original manufacturers specified parts.
! To ensure following safty repairing behavior, put the
replaced part on the components side of PWBA, not
solder side.
! To ensure using a proper screwdriver, follow the
torque and force listed in assembly and disassembly
procedures to screw and unscrew screws.
degree of 220 C.
ACER X223W
1. Product Specification
Go to cover page
1.1 SCOPE
This document defines the design and performance
The interface board will house the flat panel control logic ,
appropriate power to the whole board and LCD flat panel , and
OFF control over the whole monitor and control for DPMS LED
Signal Input
SPEC
Analog :
H : 30kHz~81kHz
V : 56Hz~76Hz
Frequency
(Analog)
Pixel clock
165MHz (Max)
Video Input
Analog
Display Pixels
Sync Signal
Signal Input
Digital :
H : 30kHz~81kHz
Frequency
(Digital)
V : 56Hz~76Hz
Pixel clock
165MHz (Max)
Video Input
0.7Vp-p
Analog
0.7Vp-p
Input Impedance 75
Connector
Input connector
Audio Jack
(OPTIONAL)
Power Consumption
AC in 100V~240V
User's Control
Front
OSD
Factory
19
1.3 ELECTRICAL
This section describes the electricalrequirement of the
Display Pixels
AC Input
Pre-Defined Timing
User
Plug and Play
electrical sub-system.
9
VESA DDC2Bi
Power Saving
VESA DPMS
H 1kHz, V 1 Hz
Figure 1
Monitor Block Diagram
CCFT Drive
Power Board
DC 5V
DC 5.3V (Audio)
AC to DC Adapter,
DC to DC Converter,
DC to AC Inverter.
Inverter control
Audio Source
Host Computer
AC - IN
(Option)
Audio
AM P.
(Option)
1W*2
Speaker
Interface Board
Flat Panel Controller, DDC
Function
Key Board
ACER X223W
Go to cover page
C o n n e c to r
P in
A s s ig n m e n t
D SU B
P in
S ig n a l
P in
S ig n a l
P in
S ig n a l
R e d -V id e o
R e d -G N D
11
N C
G re e n -V id e o
G re e n -G N D
12
D D C -S D A
B lu e -V id e o
B lu e -G N D
13
H -S Y N C
4
5
N C
D D C -G N D
9
10
+5V
S y n c -G N D
14
15
V -S Y N C
D D C -S C L
C o n n e c to r P in D e s c rip tio n
D -S U B P in D e s c riptio n
P in
N ame
1
R e d - V id e o
2
G re e n- V id e o
3
B lue - V id e o
4
GN D
5
DDC -GN D
6
Red-G N D
7
G re e n- G N D
8
B lue - G N D
9
+5V
10
S ync - G N D
11
GN D
12
DDC _SDA
13
H-SYN C
14
V-SYN C
15
DDC -SC L
D e s c riptio n
R e d vid e o signa l inp ut.
G re e n vid e o signa l inp ut.
B lue vid e o signa l inp ut.
G ro und
D D C gro und fo r the V E S A D D C 2 B i func tio n.
A na lo g signa l gro und fo r the R e d vid e o .
A na lo g signa l gro und fo r the G re e n vid e o .
A na lo g signa l gro und fo r the B lue vid e o .
+ 5 V inp ut fro m ho st syste m fo r the V E S A D D C 2 B i func tio n.
S igna l gro und
G ro und
S D A signa l inp ut fo r the V E S A D D C B 2 i func tio n.
H o rizo nta l signa l inp ut fro m the ho st syste m .
V e rtic a l signa l inp ut fro m the ho st syste m .
S C L signa l inp ut fo r the V E S A D D C 2 B i func tio n.
DVI-I / DVI-D (If using DVI-D cable, C1, C2, C3, C4, C5 is NC)
Pin
1
2
3
4
5
6
7
8
9
10
Signal
Pin
11
12
13
14
15
16
17
18
19
20
RX2RX2+
GND
NC
NC
SCL
SCA
Analog V-Sync (NC)
RX1RX1+
Signal
GND
NC
NC
5V
GND
HP
RX0RX0+
GND
NC
Pin
21
22
23
24
C1
C2
C3
C4
C5
Signal
NC
GND
RXC+
RXCAnalog Red (NC)
Analog Green (NC)
Analog Blue (NC)
Analog H-Sync (NC)
GND
Name
RX2RX2+
GND
NC
NC
SCL
SDA
Description
TMDS link #0 channel#2 differentialpair
TMDS link #0 channel#2 differentialpair
GNDfor no link share
NC
NC
Clock line for DDC interface
Data line for DDC interface
Analog
V-sync for analoginterface
8
V-Sync
9 RX1- TMDS link #0 channel#1 differentialpair
10 RX1+
11 GND
12 NC
NC
13 NC
NC
14 5V
15 GND
Pin
16
17
18
19
20
21
22
Name
HP
RX0RX0+
GND
NC
NC
GND
Description
Hot plugging
TMDS link #0 channel#0 differentialpair
TMDS link #0 channel#0 differentialpair
GNDfor no link share
NC
NC
Clock shield
23 RXC+
24 RXCAnalog
C1
Red
Analog
C2
Green
Analog
C3
Blue
Analog
C4
H-Sync
Analog
C5
GND
AnalogRed signal
AnalogGreensignal
AnalogBlue signal
H-sync for analoginterface
AnalogGND
Symbol
Item
Min Normal Max Unit
Remark
Fh
Scanning Horizontal Frequency
30
81 kHz
Minimum range
Fv
Scanning Vertical Frequency
55
76 Hz
Minimum range
Vih
Hi Level Input
2.0
5.0 V
Note 1)
Vil
Low Level Input
0
0.8 V
Note 1)
Video
RGB Analog Video Level
0.0
0.7
1.0 V
75 to Ground
1) Schmitt-Triggers Input , Supported 3.3V device H(&V) sync output from PC.
ACER X223W
Go to cover page
1.3.2.6 Abnormal Signal Immunity
CONTENT
AUDIO VOLUME
BRIGHTNESS
CONTRAST
AUTO CONTRAST
CLOCK
PHASE
H-POSITION
The indication screen is horizontally moved right and left (1 Pixels pitch).
V-POSITION
AUTO ADJUST
COLOR BALANCE
OSD POSITION
OSD LANGUAGE
Select the language used for the OSD menu among English , French ,
Italian , Deutsch and Spanish.
OSD DURATION
POWER-SAVE
Back light of the LCD panel is cut when the signal is not input (AC line
power consumption 2W or less).
INFORMATION
Table 1
Function
LED Color
Full Power
Blue color
Sleep
Orange color
is displayed.
Key
MENU
>
<
Speaker Volume/Plus
(with Audio)
Auto
Empowering
ACER X223W
Go to cover page
1.3.4.3 Mode Recognition Pull-in
screen.
standard.
1.3.6 DC - AC Inverter Requirements
see Note.(4) )
H -Sync
(K H z)
31.469
31.469
35
B and W idth
(M H z)
28.322
25.175
30.24
37.861
37.5
31.5
31.5
31.234
25.175
Item
No
R esolution
1
2
3
102
103
182
4
5
173
109
104
35.156
36
116
37.879
40
117
48.077
50
10
110
800 x 600 (75H z)
46.875
49.5
+
+
11
108
832 x 624 (74.55H z)
49.722
57.28
12
118
1024 x 768 (60H z)
48.363
65
13
157
1024 x 768 (70H z)
56.476
75
14
141
1024 x 768 (75H z)
60.023
78.75
+
+
15
126
1152 x 864 (75H z)
67.5
108
+
+
16
161
1280 x 960 (60H z)
60
108
+
+
17
179
1280 x 1024 (60H z)
63.981
108
+
+
18
131
1280 x 1024 (75H z)
79.976
135
+
+
19
1680 x1050(60H z)
65.3
146.25
+
N O TE : (1) 76 FV 86 : m onitor can display but doesn't guarantee.
(2) fV < 55, or fV > 86 : w arning invalid m ode.
(3) Factory m odel :
A fter w e first burn the code into the flash, every preset-m odel w e run first m ust do auto-adjusting.
Then it'll not do auto-adjust again w hen w e changed preset-m ode back including A C on/off D C on/off.
The only w ay that preset-m ode do auto-adjust again is press '' Internal Factory R eset''.
(4) U ser m ode :
The code should m em orize 9 tim ing m ode exclusive of preset-m odes as use m ode and do auto-adjusting.
W hen user set a new m ode that is not am ong previously. It'll do auto-adjusting then be solved to user m odes.
The new m ode w ill overw rite the first m em orized user m odes.
The user m odes be cleared is sam e as Factory m ode. Just do '' Internal Factory R eset''.
(5) Internal Factory R eset and O SD Factory R eset behavior.
The operating range shall be from 90 to 132 and 195 to 265 AVC
sinusoidal for all models specified.
Power Consumption
Power consumption for the monitor shall be less than 46W over the
specified voltage and frequency ranges. In suspend or sleep mode
the power consumption will be less than 2W.
Line Fuse
The power supply shall start and function properly when under full
load, with worst case conditions of input voltage, input frequenct,
operating temperature, and cold backlight lamps.
Inrush Current
Under Voltage
The power supply shall contain protection circuitry such that the
application of an input voltage below the minimum specified in this
table shall not cause damage to the power supply unit nor cause
failure of the input.
Line Transient
The power supply shall operate within IEC 801-4 ( 1KV) and IEC
801-5 ( 2KV) for the domestic U.S. version. The UPS power
supply shall operate and comply with CE mark.
ACER X223W
Go to cover page
1.3.8 Display Communications Channel
Temperature--------------------------
10
> 24 hours
1.4.5 Defects
1.4.5.1 Visual Inspection
measurements .
1.4.5.2 Display Degradation
all video timings from the CPU that meet the timing
manufacturer .
are as follows :
ignored.
ACER X223W
Go to cover page
1.4.5.5 Defect Terminology
1.5
Optical Characteristics
defects.
Inspection Spec.
Spots or lines that appear dark in the display patterns and are
usually the result of contam ination. D efects do not vary in
size or intensity (contrast) w hen contrast voltage is varied.
C ontrast variation can be achieved through the use of varying
gray shade patterns.
Polarizer Scratch
W hen the unit lights, lines appear light (w hite) w ith display
patterns dark and do not vary in size. Physical dam age to the
polarizer that does not dam age the glass
Polarizer D ent
W hen the unit lights, spots appear light (w hite) w ith display
patterns dark and do not vary in size. Physical dam age to the
polarizer that does not dam age the glass.
R ubbing Line
N ew ton R ing
M ottling
D im Line
C ross Lines O ff
W hen the unit lights, lines in both the m inor and m ajor axis
do not appear.
Bright / D ark D ot
Acceptable Number
Minimum Separation
< 0.1mm
Non countable
N/A
0.1 mm ~ 0.3 mm
10
15 mm
0.31 mm ~ 0.5 mm
10
15 mm
0.51 mm ~ 1.25 mm
5
15 mm
1.26 mm ~ 2.5 mm
3
25.4 mm
2.51 mm ~ 3.75 mm
3
25.4 mm
Greater than 3.75 mm
NONE
Not applicable
Note : Allowable distance between spots of two sizes is the minimum separation
number for the smaller spot. Therefore, if there are two spots, 1.30mm and 0.4mm
in diameter, they must be at least 15mm apart.
ACER X223W
2 OSD Menu
Go to cover page
2.1 MAIN OSD MENU
Outline:
M a in
M enu
Ic o n
Sub
Menu
Ic o n
Sub Menu
Ite m
N /A
W a rm
N /A
Cool
D e s c r ip t io n
S e t t h e c o lo r t e m p e r a t u r e t o
w a r m w h it e .
S e t t h e c o lo r t e m p e r a t u r e t o
c o o l w h ite .
U s e r /R e d
U s e r /G r e e n
A d ju s t s R e d /U s e r /G r e e n
G r e e n /B lu e in t e n s it y .
U s e r /B lu e
N
N
N
N
N
N
N
N
/A
/A
/A
/A
/A
/A
/A
/A
E n g lis h
D e u ts c h
F r a n c a is
E spanol
Ita lia n o
H . P o s it io n
V.
P o s it io n
OSD
T im e o u t
N /A
A u t o C o n f ig
N /A
A n a lo g
N /A
D ig it a l
N /A
D D C /C I
s w itc h
N /A
In f o r m a tio n
N /A
R eset
N /A
E x it
M u lti- la n g u a g e s e le c tio n .
A d ju s t t h e h o r iz o n t a l
p o s it io n o f th e O S D .
A d ju s t t h e v e r t ic a l p o s it io n
o f th e O S D .
A d ju s t t h e O S D t im e o u t.
A u t o A d ju s t th e H /V
P o s itio n , F o c u s a n d
C lo c k o f p ic tu r e .
( O n ly A n a lo g In p u t M o d e l)
S e le c t in p u t s ig n a l fr o m
a n a lo g (D -S u b )
( O n ly D u a l In p u t M o d e l)
S e le c t in p u t s ig n a l fr o m
d ig it a l ( D V I)
( O n ly D u a l In p u t M o d e l)
S e le c t th e D D C /C I O N o r
OFF
S h o w t h e r e s o lu t io n , H /V
f r e q u e n c y ,S N a n d
in p u t p o r t o f c u r r e n t in p u t
t im in g .
C le a r e a c h o ld s ta tu s o f
A u t o - c o n f ig u r a tio n
a n d s e t th e c o lo r
te m p e r a tu r e to W a r m .
S a v e u s e r a d ju s tm e n t a n d
O S D d is a p p e a r .
A d ju s tm e n t
R ange
N /A
N /A
R e s e t V a lu e
T h e c o lo r
t e m p e r a t u r e w ill b e
s e t to c o o l.
0 -1 0 0
100
0 -1 0 0
100
0 -1 0 0
100
N /A
T h e la n g u a g e w ill
b e s e t t o E n g lis h
0 -1 0 0
50
0 -1 0 0
50
1 0 -1 2 0
10
N /A
N /A
N /A
N /A
N /A
N /A
N /A
T h e D D C /C I s w itc h ,
d e f a u lt is O N in
m o n ito r .
N /A
N /A
N /A
N /A
N /A
N /A
ACER X223W
Go to cover page
10
ACER X223W
Go to cover page
3.1 Packing Exploded Diagram
3. Exploded Diagram
ACER X223W
Go to cover page
3.2 Product Exploded Diagram
11
ACER X223W
12
Go to cover page
4.1 Assembly procedures:
Connect the cable between power board(P802)
S1
S5
board(P306)
Connect the FFC cable into interface board
P301
P802
FFC
P306
S2
S6
base.
S3
S7
1
S4
13
ACER X223W
Go to cover page
Use a Phillips-head screwdriver screwed the No.1~4
S8
S10
noticed
S7
S11
S12
S8
1
S9
S13
ACER X223W
14
Go to cover page
S14
S18
attached.
S19
Assemble the stand upper side to the rear cover
S15
S16
S20
S17
tapes.
ACER X223W
Go to cover page
S21
USERS MANUAL
STAND
S22
DVI CABLE
POWER CABLE
D-SUB CABLE
FEATURE LABEL
VISTA LABEL
15
ACER X223W
16
Go to cover page
4.2 Disassembly procedures
S1
S4
FEATURE LABEL
VISTA LABEL
S2
USERS MANUAL
STAND
S3
DVI CABLE
POWER CABLE
the accessories.)
S5
D-SUB CABLE
S6
S7
ACER X223W
17
Go to cover page
Unhook the key function board from rear bezel,
S8
S9
S10
S11
ACER X223W
18
Go to cover page
S12
S15
S13
S16
S14
S17
1
2
ACER X223W
Go to cover page
Use a Phillips-head screwdriver unscrewed the
S18
S19
P802
P301
FFC
P306
19
ACER X223W
20
5. Troubleshooting
Go to cover page
5.1 No.display of screen (Screen is black, color of LED is
amber)
No
When a signal isn't being inputted, it is
indicated with "No Signal Input". it is
indicated with "Out Of Range" at the
time of the frequency that it can't be
distinguished.
Yes
NG
OK
ACER X223W
5. Troubleshooting (continued)
Go to cover page
5.2 Nothing display on screen (screen is black, color of LED is
blue)
Is backlight lit?
NG
OK
Is backlight lit?
NG
OK
NG
Failure Point
NG
OK
OK
Next
Page
21
22
ACER X223W
5. Troubleshooting (continued)
Go to cover page
5.2 Nothing display on screen (screen is black, color of LED is
blue) continued
Continue
NG
OK
NG
OK
OK
Check the I301 pin2
if voltage is 5V
NG
Failure Point
1) FB301 is open.
2) C309, C310 is short.
OK
NG
OK
NG Failure Point
1) Printer wire between R307
and I305 pin85 is failure
2) I305 is failure.
Failure Point
I301 is failure.
OK
Failure Point
NG
Failure Point
NG
OK
OK
Failure Point
Check the P304 all
LVDS signals.
I305 is failure
Failure Point
NG
OK
Failure Point
1) The LVDS cable broke between
P304 and LCD module.
2) LCD module is failure.
5. Troubleshooting (continued)
ACER X223W
Go to cover page
5.3 Checking the back light unit
Failure Point
NG
OK
Failure Point
NG
OK
Failure Point
1) Back light unit of LCD module is
failure.
2) Inverter Cable is disconnected
23
24
ACER X223W
5. Troubleshooting (continued)
Go to cover page
5.4 Abnormal screen for VGA
NG
Failure Point
OK
1) No R, G, B video signals output from
host computer, check computer.
2) Video signal cable disconnection.
NG
OK
NG
OK
Failure Point
In the case of the Red signal. (A Green and
Blue signal is the same path, too.)
1) Printed wire broke between P302 pin1
and I306 pin23.
2) Video cable is failure.
3) FB303,FB304, R309 is open.
4) R311 is short or open.
5) C315 is short or open.
Failure Point
Printed wire broke between I305 and P304.
ACER X223W
5. Troubleshooting (continued)
Go to cover page
5.5 Abnormal OSM display adjust problem
NG
Failure Point
1) Function key wire disconnection.
2) Function key wire is failure.
3) Function key board is failure.
OK
NG
OK
Failure Point
I305 is failure.
Failure Point
1) Printed wire broke among P306 pin4, pin5; R369 and I305
pin90.
2) Printed wire broke among P306 pin5,R372, and I305 pin89.
3)C386,C388 ,C389,C390 are short.
25
26
ACER X223W
5. Troubleshooting (continued)
Go to cover page
5.6 Abnormal plug and play operation for VGA
NG
OK
Failure Point
The host machine is not communicatiog in DDC2B
mode.
Failure Point
The Video cable is failure.
NG
Failure Point
1) Printed wire broke between I303 pin8, D308
and P302 pin9.
2) D309, C329 is short.
3) D308 is failure.
OK
NG
Failure Point
OK
The Video cable is failure.
Failure Point
OK
I303 is failure.
Failure Point
1) Printed wire broke among I305 pin30, pin31,
R328,R330 and P302 pin12, 15 .
2) I303 maybe failure.
3) R326, R327 are open.
4) R328 or R330 or C330 or C331 is open or
short.
5. Troubleshooting (continued)
ACER X223W
Go to cover page
5.7 Checking the interface circuit of sync signal
5.7.1 Checking the control circuit of horizontal sync pulse
NG
Failure Point
OK
Video cable is failure.
NG
Failure Point
OK
Failure Point
Process "Checking the resolution change IC
movement" section.
27
28
ACER X223W
5. Troubleshooting (continued)
Go to cover page
5.8 Checking the resolution change IC movement
NG
NG
OK
OK
OK
Failure Point
NG
Check if D328 pin1 is low.
NG
OK
Failure Point
OK
Failure Point
NG
OK
Failure Point
I306 failure.
1) Printed wire broke between I305 pin37, pin38, pin39, pin40 and
I306 pin1, pin2, pin5, pin6.
2) I306 failure.
5. Troubleshooting (continued)
ACER X223W
Go to cover page
5.9 Checking the DC/DC converter circuit
OK
NG
Failure Point
1) Power wire disconnection.
2) Power board is failure.
NG
Failure Point
OK
1) Printed wire broke between P301 pin5,
pin6, and I302 pin3.
NG
OK
Failure Point
I302 is failure.
OK
NG
Failure Point
NG
OK
Failure Point
1) Printed wire broke between I302 pin 2. 4,
Q306 pin1 and I305 VCTRL pin.
2) FB311, FB312, FB313, FB314, FB315, are
open.
Failure Point
D326 is failure.
29
AC
110/220V
Input
Power &
Invertor
Board
P301
Power Con.
VCTRL
1.8v
Flash EPROM
SST 25VF010A
PMC 25LV010A
I306
Q305
I302
DC-DC
5v-3.3v
+5V
Brightness,Inv_On/Off
Backlight
LVDS
Panel Con.
P304
LCD Module
AUO M220EW01-V2/V0
M201EW02-V8/V9
CPT CLAA201WA04A
SEC LTM220M1-V0/L01
VLCD
I305
Scaler
10
R,G,B,Hs,Vs
RC
Reset
X301
XTAL
14.318MHZ
11
I303
DDC
24LC02B
12
P306
Key
Con.
12
VGA_DDC_CLK,
VGA_DDC_DAT
11
Analog
Video
Input
P302
Digital
Video
Input
P303
10
D-SUB
DVI-D
TMDS
TSUMU58BWHL-LF
I304
DDC
24LC02B
DVI OPTION
DVI_DDC_SCL,
DVI_DDC_DAT
PCB No.
13
Function
Key
Board
13
6832190100P01
ACER X223W
Go to cover page
30
L
G
1
3
F801
2.5AL250V
R802
SCK103
T802
LINE FILTER
R801
C801
0.33U/275V
I801
C820
1000P/250V
C807
10UF/50V
BEAD
L809
C819
0.22U/275V
A
2
1M
1/4W
MGF
C808
SG5841J
1000P/250V
5
4
BRI
C812
1000P
GND-1
ON_OFF
10K
R113
R102
30.1K 1%
GND
ZD801
22D
D807
RL206
D805
RL206
4
2
GND
C106
0.047uF
D808
RL206
R824
33K 1%
GND
C108
220P
R818
0.51/1W
R829
NA
R812
100K/2W
D801
X
GND-1
T801
ER28
Q105
C945 22 MOF
R131
Q106
A733
GND
D804
1N4937
L803
BEAD/6mm
C810
100P
1KV X7R
R811
0.39/2W
R134
1K
R132
1K
GND-1
GND
Q104
2N7000
R830
243K
D803
1N4007
C806
0.01U/1KV
R133
22 MOF
Q803
7N65C
R807
3.3
R804
+
C805
2M
100U/450V 1/4W
MGF
GND-1
D806 1N4148
1
2
C830
4700P/1KVX7R
D812
RL206
R814
C104
330P
R107
6.8K
R118
31.6K 1%
33.2K 1%
R827
C827
0.01UF/PEM
R823
270
R813
100/MOF
1K
R825
150K 1%
R106
GND
I803
AP431 1%
22/MOF
R826
1K
R104
510K 1%
GND
GND
GND
C828
4.7U/50V
10
11
12
13
14
15
16
I802
LTV817
R815
200/MOF
C809
4700P/1KVX7R
C825
1000P/250V
GND-1
C811
220P
DRV2
PGND
I101
DRV1
CT
GNDA
VDDA
TIMER
DIM
SSTCMP
LCT
ISEN
VSEN
ENA
NC
OVPT
NC
C103
2.2uF/50V
GND
2
3
P801
GND
R808
30.1K 1%
+5V
R105
20
C101
0.1uF
R103
30.1K 1%
OZ9938
GND
4
2
3
1
R833
30.1K 1%
C110
1
GND
C132
1000P
10
8
7
GND
8
R831
X
C816
1000P
GND
D2
D2
D2
C134 +
10
C851
0.1UF
+5V
T101
D105
D104
1N4148
1
2
T102
D107
1N4148
1N4148
D811
24C
GND
GND
GND
5V
5V
5V
5V
BRI
ON_OFF
GND
R817
1K
BRI
GND
R126
3.65K 1%
R125
3M 1/4W
C123
10P/6KV
C109
0.022UF
X7R
GND
R115
3.65K 1%
R116
3M 1/4W
C117
10PF/6KV
GND
ON_OFF
11
4
5
6
10
EEL19-B
1
2
3
+
C823
1000UF/16V
GND
R137
100K
1
2
3
11
4
5
6
10
EEL19-B
D109
D110
1N4148
1
2
1N4148
1N4148
D108
1
R138
100K
R140
100K
R139
100K
R120
13K
GND
GND
10
C817
330U/35V
GND
L802
10U
+
C824
1000UF/16V
C127
330UF/35V
+
C128
330UF/35V
330UF/35V
GND
C135
330UF/35V
GND
+
C818
330U/35V
GND
+
C822
1000UF/16V
Q107
S2
D2
S2
D1
D1
D1
AOP609
G2
G1
G2
D1
GND
R130
402 1%
S1
C131
0.022UF
X7R
G1
AOP609
Q108
S1
GND
100V X7R
C821
1000P
500V X7R
D809
ER1002FCT
C129
220UF/35V
D810
SB1060F
R832
X
+22V
GND
GND
D113
1N4148
D112
1N4148
GND
C130
220UF/35V
R128
13K
2
1
2
C133
1000P
GND
R136
10K
C102
22uF/50V
2.2uF/50V
GND
C111
1000P
GND
R135
1M
GND
R101
10K
C105
1000P
GND
12
R828
51K
GND
P802
1
2
3
4
5
6
7
8
9
10
R117
100K 1%
R119
13K 1%
R122
13K 1%
R121
100K 1%
GND
R111
402 1%
F101
3A
C116
5PF/3KV
C115
470P
X7R
GND
GND
C113
0.1UF
13
+22V
GND
D103
1N4148
GND
C114
0.1UF
D115
1N4148
GND
13
P101
2P
P102
2P
P103
2P
P104
2P
6832192600P01
D102
1N4148
C125
5P/3KV
C120
470P
X7R
GND
2 D114
1N4148
12
PCB No.
1
2
1
2
1
2
1
2
ACER X223W
Go to cover page
31
VDD
VLCD
VCC5V
VCC5V
VCC5V
VCC3V3
VLCD
VCC5V
POWER
VCC5V
VDD
DDC_WPn
RX2+
RX2RX1+
RX1RX0+
RX0RXC+
RXC-
HDCP_CTRLn
DVI_DETn
DVI_DDC_DAT
DVI_DDC_CLK
PANELVCC_EN
VCC3V3
VLCD
2.POWER
BKLT_EN
BKLT_ADJ
VCC5V
DDC_WPn
VGA_DDC_DAT
VGA_DDC_CLK
VGA_DETn
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSYNC
VSYNC
6.3 ACER_LCD_X223W_SCHEMATICS_INTERFACE_TOP
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSYNC
VSYNC
VGA_DETn
VGA_DDC_DAT
VGA_DDC_CLK
DDC_WPn
DDC_WPn
RX2+
RX2RX1+
RX1RX0+
RX0RXC+
RXC-
HDCP_CTRLn
DVI_DETn
VCC5V
DVI_DDC_DAT
DVI_DDC_CLK
VCC3V3
BKLT_EN
BKLT_ADJ
PANELVCC_EN
SCALER TSUMU58BWHL-LF
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSYNC
VSYNC
VGA_DETn
VGA_DDC_DAT
VGA_DDC_CLK
DDC_WPn
RX2+
RX2RX1+
RX1RX0+
RX0RXC+
RXC-
HDCP_CTRLn
DVI_DETn
DVI_DDC_DAT
DVI_DDC_CLK
VCC5V
VCC3V3
BKLT_EN
BKLT_ADJ
PANELVCC_EN
5.SCALER TSUMU58BWHL-LF
LVACKP
LVACKM
LVA0P
LVA0M
LVA1P
LVA1M
LVA2P
LVA2M
LVA3P
LVA3M
LVBCKP
LVBCKM
LVB0P
LVB0M
LVB1P
LVB1M
LVB2P
LVB2M
LVB3P
LVB3M
LED_G
LED_A
ADC1_IN
ADC2_IN
VOLUME
AUDIO_EN
LVACKP
LVACKM
LVA0P
LVA0M
LVA1P
LVA1M
LVA2P
LVA2M
LVA3P
LVA3M
LVBCKP
LVBCKM
LVB0P
LVB0M
LVB1P
LVB1M
LVB2P
LVB2M
LVB3P
LVB3M
LED_G
LED_A
ADC1_IN
ADC2_IN
10
AUDIO_EN
VOLUME
10
11
12
VCC3V3
VLCD
LVACKP
LVACKM
LVA0P
LVA0M
LVA1P
LVA1M
LVA2P
LVA2M
LVA3P
LVA3M
LVBCKP
LVBCKM
LVB0P
LVB0M
LVB1P
LVB1M
LVB2P
LVB2M
LVB3P
LVB3M
LED_G
LED_A
ADC1_IN
ADC2_IN
12
VDD
AUDIO
AUDIO_EN
VOLUME
7.AUDIO
11
PCB No.
13
VLCD
VDD
13
VCC3V3
6832190100P01
ACER X223W
Go to cover page
32
P301
TP1
BACKLIGHT_ADJ
BACKLIGHT_EN
VDD
9
8
7
6
5
4
3
2
1
JWT-A2001WV2-9P
VDD
TP5
100uF/16V
C303
C302
0.1uF
2K4
VDD
Su scon UK 3000hrs
VCC5V
100uF/16V
C307
VCC5V
C306
VCC5V
0.1uF
TP2
C305
TP3
C304
0.1uF(NC)
0.1uF
C308
47K
R304
TP7
R301
R303
100(22K)
1K
DC
PULSE
I301
AO3419/3401
2
Su scon UK 3000hrs
C310
TP11
C309
47K
R305
10uF/16V
Q301
MMBT3904
VCC3V3
TP14
C314
VCC3V3
0.1uF
R306
10K
TP10
Su scon UK 3000hrs
0.1uF
TP13
2
PBY160808T-600Y-S
C301
R307
FB301
0.1uF
TP12
R308
VOUT
SOT-223
VIN
TAB
I302
ADJ
100uF/16V
VCC5V
PANELVCC_EN
3
1
AIC1084_33PM
VCC5V
R302
R301
NC
R302
10
C301
100
4K7
1K(NC)
NC
22K
PBY160808T-600Y-S
0.1uF
FB302
TP4
TP6
VLCD
11
BKLT_ADJ
TP9
BKLT_EN
C312
TP8
C311
VLCD
12
BKLT_ADJ
BKLT_EN
VLCD
13
Case_GND
Hole4
8
7
6
5
Case_GND
8
7
6
5
Hole3
8
7
6
5
Case_GND
8
7
6
5
Hole2
13
Case_GND
12
Hole1
11
0.1uF
10
0.1uF
6832190100P01
4
3
2
1
4K7
VCC5V
C313
100uF/16V
PCB No.
4
3
2
1
PANELVCC_EN
4
3
2
1
4
3
2
1
3
1
ACER X223W
Go to cover page
33
TP15
D302
MMBD7000
C320
0.1uF
TP16
D303
MMBD7000
VCC5V
TP35
D305
47
47
C321
0.1uF
MMSZ5232B
TP37
R328
R330
TP40
FB303
TP17
FB305
4K7
VCC5V
FB307
R320
SBK160808T-110Y-S
SBK160808T-110Y-S
SBK160808T-110Y-S
VCC5V
R319
47K
C325
SBK160808T-451Y-S
0.1uF
FB309
3
N
P
2
TP165
7
TP166
TP167
FB304
FB306
FB308
SBK160808T-600Y-S
SBK160808T-600Y-S
SBK160808T-600Y-S
C327
VGA_RIN
VGA_GIN
100pF
VGA_BIN
R324
R313
2K4
75_1%
C326
R312
100pF
75_1%
R323
R311
2K4
75_1%
TP38
D307
TP41
MMSZ5232B
1
2
3
4
D306
24C02
VCC
WP
SCL
SDA
I303
VCC_VGA
8
7
6
5
TP50
TP51
A0
A1
A2
GND
MMSZ5232B
TP43
C329
VCC_VGA
D309
D308
BAT54C
R327
VGA_DDC_CLK
VGA_DDC_DAT
R326
C331
C328
47pF
0.1uF
C330
MMSZ5232B
47pF
12K
D311
12K
MMSZ5232B
D310
MMSZ5232B
0.1uF
TP44
P
1
SBK160808T-451Y-S
VCC5V
FB310
VGA5V
D301
MMBD7000
VCC5V
TP46
TP49
VGA_RED
VGA5V
VGA_GREEN
VGA_CONn
VGA_BLUE
VGA_HSYNC
VCC5V
VGA_CONn
VGA_HSYNC
VGA_VSYNC
VGA_SCL
VGA_SDA
VGA_SDA
VGA_SCL
VGA_VSYNC
MMSZ5232B(NC)
D304
C319
0.1uF
P302
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
CONNECTOR DB15
10
TP18
TP23
TP30
R309
R310
68
100
11
TP19
C315
C316
47nF
47nF
47nF
TP24
C317
1nF
TP21
TP26
C318
68
470
R314
R315
47nF
47nF
C322
TP31
C323
12
TP20
TP22
TP25
TP27
TP29
TP32
TP34
RIN
GNDR
GIN
SOG
13
RIN
GNDR
GIN
SOG
GNDG
BIN
GNDB
VGA_DETn
HSYNC
VSYNC
DDC_WPn
VGA_DDC_CLK
VGA_DDC_DAT
13
6832190100P01
GNDG
BIN
GNDB
VGA_DETn
HSYNC
VSYNC
DDC_WPn
PCB No.
12
VGA_DDC_DAT
VGA_DDC_CLK
4K7
R331
TP48
TP42
TP39
47nF
TP33
2K4
R329
C324
TP28
100
68
R316
R317
100
470
R318
R321
470
TP36
HSYNC_IN
R322
R325
4K7
Q302
MMBT3904
11
TP47
VSYNC_IN
TP45
10
17
16
ACER X223W
Go to cover page
34
VCC3V3
1
VCC3V3
FB311
PBY160808T-301Y-S
Su scon UK 3000hrs
C349
C348
0.1uF
TP81
C347
0.1uF
VDVI
C346
0.1uF
C365
C366
C367
0.1uF
C368
4
FB312
0.1uF
C381
TP99
TP97
VPLL
C352
C351
0.1uF
TP82
C350
0.1uF
VMPLL
1uF
TP91
C374
0.1uF
37
38
39
40
80
52
53
FB313
VDVI
VMPLL
C355
C354
0.1uF
TP83
C353
0.1uF
VPO
8
FB314
81
54
55
58
59
60
61
62
63
64
65
67
68
69
70
71
72
73
74
77
78
C358
TP84
C357
0.1uF
VAD
C356
1uF
41
42
VGA_DETn
VOLUME
DDC_WPn
PANELVCC_EN
BKLT_ADJ
AUDIO_EN
TP103
R361
R362
4K7(NC)
TP105
10
VCC3V3
FB315
C361
C362
C363
12
C360
TP85
C359
0.1uF
11
VPO
PBY160808T-301Y-S
0.1uF
VCTRL
TP89
Q305
MMBT2907A
1N4148/NC
D326
S1A
D325
0.1uF
0.1uF
D327
R356
TP90
20K(NC)
ADC1_IN
ADC2_IN
TP88
13
R351
50
C370
4.7uF/16V
R352
10uF/16V
C371
VCC1V8
2K
6832190100P01
13
VCC3V3
10uF/16V
C372
1N4148
C375
10K
R355
VCC5V
100
R353
1uF(NC)
TP96
0.1uF
C377
1
2
3
4
PCB No.
12
24C16
A0
A1
A2
GND
ADC1_IN
ADC2_IN
0.1uF
VCC
WP
SCL
SDA
I307
C376
C382
8
7
6
5
0.1uF
0.1uF
VCC3V3
R360
11
SCL
SDA
4K7
TP104
R359
TP106
4K7
VCC5V
Su scon UK 3000hrs
10
47
47
DVI_DETn
HDCP_CTRLn
LED_G
LED_A
BKLT_EN
VGA_DETn
VOLUME
DDC_WPn
PANELVCC_EN
BKLT_ADJ
AUDIO_EN
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
LVA3P
LVA3M
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
1uF
TP87
C369
0.1uF
35
47
48
85
86
CHIP_STBYn
BKLT_EN
ADC1_IN
ADC2_IN
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
87
88
89
90
LED_G
LED_A
VCC3V3
I2C_SCL
I2C_SDA
R357
DVI_DETn
HDCP_CTRLn
44
43
91
92
93
94
95
99
36
45
46
LVA3P
LVA3M
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
PBY160808T-301Y-S
VCC3V3
VCC1V8
VCTRL
LVA3P
LVA3M
LVACKP
LVACKM
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
GPIO_P23
NC
NC
GPIO_P47
GPIO_P46
GPIO_P10/I2C_MCL
GPIO_P11/I2C_MDA
GPIO_P07
GPIO_P15
GPIO_P16/PWM1
GPIO_P12
GPIO_P13
GPIO_P14/PWM0
GPIO_P00/SAR0
GPIO_P01/SAR1
GPIO_P02/SAR2
GPIO_P03/SAR3
GPIO_P22/PWM0
GPIO_P24/PWM2
GPIO_P45/PWM1
GPIO_P25
GPIO_P27/PWM3
TSUMU58BWHL-LF
RIN0P
RIN0M
GIN0P
GIN0M
SOGIN0
BIN0P
BIN0M
HSYNC0
VSYNC0
DDCA_SDA/RS232_TX
DDCA_SCL/rs232_RX
R+
RG+
GB+
BCK+
CKDDCD_SDA
DDCD_SCL
REXT
REFP
REFM
SDO
CSZ
SCK
SDI
RST
XIN
XOUT
BYPASS
MODE[0]
MODE[1]
1uF
VPLL
VAD
VPLL
PBY160808T-301Y-S
VCC3V3
I305
26
SPI_SDO
SPI_CSn
SPI_SCK
SPI_SDI
84
25
RESET
96
XOUT
TP101
BYPASS
TP102
97
TP100
XIN
TP95
15
23
22
20
19
21
18
17
27
28
30
31
22pF
0.1uF
TP92
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSYNC
VSYNC
VGA_DDC_DAT
VGA_DDC_CLK
22pF
390_1%
3
4
6
7
9
10
12
13
100
1
C383
C380
X301
14.318MHZ
C379
R354
RX0+
RX0RX1+
RX1RX2+
RX2RXC+
RXCDVI_DDC_DAT
DVI_DDC_CLK
PBY160808T-301Y-S
VCC3V3
C364
0.1uF
RIN
GNDR
GIN
GNDG
SOG
BIN
GNDB
HSYNC
VSYNC
VGA_DDC_DAT
VGA_DDC_CLK
RX0+
RX0RX1+
RX1RX2+
RX2RXC+
RXCDVI_DDC_DAT
DVI_DDC_CLK
TP94
TP98
R358
10uF/16V
C378
VCC5V
SPI_SCK
SPI_SDI
0.1uF
C373
VCC3V3
0.1uF
TP86
10uF/16V
8
7
6
5
0.1uF
I306
CE#
SO
WP#
GND
D328
100K
RESET
1N4148
R389
2K4/NC
VCC5V
Su scon UK 3000hrs
PM25LV010A/SST25VF010A
VCC
HOLD#
SCK
SI
10uF/16V
1
2
3
4
VCC5V
C404
0.1uF/NC
TP168
34
A
VCC1V8
TP93
SPI_CSn
SPI_SDO
VCC5V
I309
VCC
RST
GND
STLMIC810MU/NC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
2
5
11
29
33
50
57
76
79
83
VDDC
51
66
82
VDDC
VDDC
VDDC
32
49
56
75
VDDP
VDDP
VDDP
VDDP
24
AVDD_33
16
AVDD_33
98
AVDD_33
8
14
AVDD_33
AVDD_33
ACER X223W
Go to cover page
35
LVA0P
LVA0M
LVA1P
LVA1M
LVA2P
LVA2M
LVACKP
LVACKM
LVA3P
LVA3M
LVA0P
LVA0M
LVA1P
LVA1M
LVA2P
LVA2M
LVACKP
LVACKM
LVA3P
LVA3M
TP107
TP125
TP109
TP123
TP111
TP121
TP119
TP113
TP117
TP115
R363
4K7
TP128
R366
4K7
KEY_MENU
LVB0P
LVB0M
LVB1P
LVB1M
LVB2P
LVB2M
LVBCKP
LVBCKM
LVB3P
LVB3M
R369
100
LVB0P
LVB0M
LVB1P
LVB1M
LVB2P
LVB2M
LVBCKP
LVBCKM
LVB3P
LVB3M
VCC3V3
KEY_AUTO
100
KEY_E
R372
KEY_LEFT
0.
694V(15Kohm)
0.
498V
1.
14V(30Kohm)
0.
846V
1.
641V(56Kohm)
TP108
TP126
TP110
TP124
TP112
TP122
TP118
TP116
TP114
TP120
VCC3V3
C389
0.1UF
C390
R365
0.1UF
56K_1%
C388
R364
0.1UF
56K_1%
C386
0.1UF
TP130 TP131
10
VLCD
LED_Blue
LED_Amber
KEY_ADC2
KEY_ADC1
10
11
LVB0M
LVB0P
LVB1M
LVB1P
LVB2M
LVB2P
LVBCKM
LVBCKP
LVB3M
LVB3P
LVA0M
LVA0P
LVA1M
LVA1P
P306
LVA2M
LVA2P
LVACKM
LVACKP
LVA3M
LVA3P
VLCD
VLCD
1
2
3
4
5
6
12
JWT-A2001WV2-06
12
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
13
P304
CVILUX-CF25302D0R0
13
TP127
TP136
11
LED_A
LED_G
ADC2_IN
KEY_RIGHT
0.
694V(15Kohm)
ADC1_IN
KEY_POWER
1.
14V(30Kohm)
TP137
1.
641V(56Kohm)
0.
498V
LED_A
LED_G
ADC2_IN
ADC1_IN
ADC2_IN
ADC1_IN
0.
846V
6832190100P01
PCB No.
ACER X223W
Go to cover page
36
100
100
56K_1%
30K_1%
15K_1%
R605
R606
R607
C602
0.1uF(NC)
R601
R600
R602
R603
R604
C601
0.1uF(NC)
56K_1%
30K_1%
15K_1%
10
10
11
LEDBLUE
12
D601
LED
LEDORANGE
S604
Menu KEY
SW PUSHBUTTON
S606
E KEY
SW PUSHBUTTON
S605
AUTO/EXIT KEY
SW PUSHBUTTON
S601
POWER KEY
SW PUSHBUTTON
S603
LEFT KEY
SW PUSHBUTTON
S602
RIGHT KEY
SW PUSHBUTTON
11
12
7
8
JWT-CN125WR0-6PS
1
2
3
4
5
6
P601
PCB No.
13
13
6832192500P01
ACER X223W
Go to cover page
37
10
11
12
13
13
12
11
10
PCB No.
ACER X223W
Go to cover page
38
10
11
12
13
13
12
11
10
PCB No.
ACER X223W
Go to cover page
39
10
11
12
13
13
12
11
10
PCB No.
ACER X223W
Go to cover page
40