Professional Documents
Culture Documents
FS-1350DN: Service Manual
FS-1350DN: Service Manual
SERVICE
MANUAL
Published in October 2008
842H4010
2H4SM060
First Edition
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF
USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
It may be illegal to dispose of this battery into the municipal waste stream. Check with your local
solid waste officials for details in your area for proper disposal.
ATTENTION
IL Y A UN RISQUE DEXPLOSION SI LA BATTERIE EST REMPLACEE PAR UN MODELE DE
TYPE INCORRECT. METTRE AU REBUT LES BATTERIES UTILISEES SELON LES INSTRUCTIONS DONNEES.
Il peut tre illgal de jeter les batteries dans des eaux dgout municipales. Vrifiez avec les fonctionnaires municipaux de votre rgion pour les dtails concernant des dchets solides et une mise
au rebut approprie.
Revision history
Revision
Date
Replaced pages
Remarks
Safety precautions
This booklet provides safety warnings and precautions for our service personnel to ensure the safety of
their customers, their machines as well as themselves during maintenance activities. Service personnel
are advised to read this booklet carefully to familiarize themselves with the warnings and precautions
described here before engaging in maintenance activities.
DANGER: High risk of serious bodily injury or death may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
WARNING: Serious bodily injury or death may result from insufficient attention to or incorrect compliance
with warning messages using this symbol.
CAUTION: Bodily injury or damage to property may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
Symbols
The triangle ( ) symbol indicates a warning including danger and caution. The specific point
of attention is shown inside the symbol.
General warning.
Warning of risk of electric shock.
indicates a prohibited action. The specific prohibition is shown inside the symbol.
General prohibited action.
Disassembly prohibited.
indicates that action is required. The specific action required is shown inside the symbol.
General action required.
Remove the power plug from the wall outlet.
Always ground the copier.
1.Installation Precautions
WARNING
Do not use a power supply with a voltage other than that specified. Avoid multiple connections to
one outlet: they may cause fire or electric shock. When using an extension cable, always check
that it is adequate for the rated current. .............................................................................................
Connect the ground wire to a suitable grounding point. Not grounding the copier may cause fire or
electric shock. Connecting the earth wire to an object not approved for the purpose may cause
explosion or electric shock. Never connect the ground cable to any of the following: gas pipes,
lightning rods, ground cables for telephone lines and water pipes or faucets not approved by the
proper authorities. ............................................................................................................................
CAUTION:
Do not place the copier on an infirm or angled surface: the copier may tip over, causing injury. .......
Do not install the copier in a humid or dusty place. This may cause fire or electric shock. ................
Do not install the copier near a radiator, heater, other heat source or near flammable material.
This may cause fire. .........................................................................................................................
Allow sufficient space around the copier to allow the ventilation grills to keep the machine as cool
as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ...........
Always handle the machine by the correct locations when moving it. ...............................................
Always use anti-toppling and locking devices on copiers so equipped. Failure to do this may cause
the copier to move unexpectedly or topple, leading to injury. ...........................................................
Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is accidentally ingested, drink a lot of water to dilute it in the stomach and obtain medical attention immediately. If it gets into the eyes, rinse immediately with copious amounts of water and obtain medical
attention. ......................................................................................................................................
Advice customers that they must always follow the safety warnings and precautions in the copiers
instruction handbook. .....................................................................................................................
Always remove the power plug from the wall outlet before starting machine disassembly. ...............
Always follow the procedures for maintenance described in the service manual and other related
brochures. .......................................................................................................................................
Under no circumstances attempt to bypass or disable safety features including safety mechanisms
and protective circuits. .....................................................................................................................
Always check that the copier is correctly connected to an outlet with a ground connection. .............
Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it
is dirty, clean it to remove the risk of fire or electric shock. ..............................................................
Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may
damage eyesight. ...........................................................................................................................
Handle the charger sections with care. They are charged to high potentials and may cause electric
shock if handled improperly. ............................................................................................................
CAUTION
Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are
safely secured so they will not be caught in rotating sections. ..........................................................
Use utmost caution when working on a powered machine. Keep away from chains and belts. ........
Handle the fixing section with care to avoid burns as it can be extremely hot. ..................................
Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause
abnormally high temperatures. ........................................................................................................
Do not remove the ozone filter, if any, from the copier except for routine replacement. ....................
Do not pull on the AC power cord or connector wires on high-voltage components when removing
them; always hold the plug itself. .....................................................................................................
Do not route the power cable where it may be stood on or trapped. If necessary, protect it with a
cable cover or other appropriate item. .............................................................................................
Treat the ends of the wire carefully when installing a new charger wire to avoid electric leaks. ........
Run wire harnesses carefully so that wires will not be trapped or damaged. ....................................
After maintenance, always check that all the parts, screws, connectors and wires that were
removed, have been refitted correctly. Special attention should be paid to any forgotten connector,
trapped wire and missing screws. ...................................................................................................
Check that all the caution labels that should be present on the machine according to the instruction
handbook are clean and not peeling. Replace with new ones if necessary. ......................................
Handle greases and solvents with care by following the instructions below: .....................................
Use only a small amount of solvent at a time, being careful not to spill. Wipe spills off completely.
Ventilate the room well while using grease or solvents.
Allow applied solvents to evaporate completely before refitting the covers or turning the power switch on.
Always wash hands afterwards.
Never dispose of toner or toner bottles in fire. Toner may cause sparks when exposed directly to
fire in a furnace, etc. .......................................................................................................................
Should smoke be seen coming from the copier, remove the power plug from the wall outlet immediately. ............................................................................................................................................
3.Miscellaneous
WARNING
Never attempt to heat the drum or expose it to any organic solvents such as alcohol, other than the
specified refiner; it may generate toxic gas. .....................................................................................
2H4
CONTENTS
1-1 Specifications
1-1-1 Specifications..........................................................................................................................................1-1-1
1-1-2 Parts names............................................................................................................................................1-1-3
(1) Overall ...............................................................................................................................................1-1-3
(2) Operation panel.................................................................................................................................1-1-4
1-1-3 Machine cross section ............................................................................................................................1-1-5
1-2 Installation
1-2-1 Installation environment ..........................................................................................................................1-2-1
1-2-2 Unpacking ...............................................................................................................................................1-2-2
(1) Removing the tapes ..........................................................................................................................1-2-3
1-2-3 Installing the expanded memory (option)................................................................................................1-2-4
1-2-4 Installing the memory card (optional)......................................................................................................1-2-5
1-4 Troubleshooting
1-4-1 Paper misfeed detection .........................................................................................................................1-4-1
(1) Paper misfeed indication ...................................................................................................................1-4-1
(2) Paper misfeed detection condition ....................................................................................................1-4-1
1-4-2 Self-diagnostic function...........................................................................................................................1-4-2
(1) Self-diagnostic function .....................................................................................................................1-4-2
(2) Self diagnostic codes ........................................................................................................................1-4-3
1-4-3 Image formation problems ......................................................................................................................1-4-7
(1) Completely blank printout..................................................................................................................1-4-8
(2) All-black printout................................................................................................................................1-4-8
(3) Dropouts............................................................................................................................................1-4-9
(4) Black dots..........................................................................................................................................1-4-9
(5) Black horizontal streaks. ...................................................................................................................1-4-9
(6) Black vertical streaks.......................................................................................................................1-4-10
(7) Unsharpness. ..................................................................................................................................1-4-10
(8) Gray background.............................................................................................................................1-4-10
(9) Dirt on the top edge or back of the paper........................................................................................1-4-11
(10) Undulated printing at the right edge (scanning start position). ........................................................1-4-11
1-4-4 Electric problems ..................................................................................................................................1-4-12
1-4-5 Mechanical problems ............................................................................................................................1-4-14
2H4
(1) Detaching and refitting the fuser unit...............................................................................................1-5-16
(2) Switching the fuser pressure ...........................................................................................................1-5-18
1-5-8 PWBs ....................................................................................................................................................1-5-19
(1) Detaching and refitting the control PWB .........................................................................................1-5-19
(2) Detaching and refitting the power source PWB...............................................................................1-5-22
(3) Detaching and refitting the high voltage PWB.................................................................................1-5-24
1-5-9 Others ...................................................................................................................................................1-5-28
(1) Detaching and refitting the main motor ...........................................................................................1-5-28
(2) Detaching and refitting the laser scanner unit .................................................................................1-5-29
(3) Detaching and refitting the eraser lamp (PWB)...............................................................................1-5-31
(4) Direction of installing the left cooling fan motor and right cooling fan motor ...................................1-5-32
1-6 Firmware
1-6-1 Downloading firmware ............................................................................................................................1-6-1
(1) Firmware files ....................................................................................................................................1-6-1
(2) Downloading the firmware from the USB memory ............................................................................1-6-2
(3) Downloading the firmware from the memory card.............................................................................1-6-4
2-4 Appendixes
2-4-1 Appendixes .............................................................................................................................................2-4-1
(1) Wiring diagram ..................................................................................................................................2-4-1
(2) Repetitive defects gauge...................................................................................................................2-4-2
2H4
1-1 Specifications
1-1-1
Specifications
1-1-1
2H4
Controller ........................................ PowerPC 440F5/500 MHz
Supported OS ................................. Windows 2000 Service Pack 2 or later, Windows Server 2003, Windows XP,
Windows Vista, Mac OS X 10.x
Interface.......................................... Hi-Speed USB: 1
Network: 1 (10BASE-T/100BASE-TX)
KUIO-W slot: 1
PDL................................................. PRESCRIBE
Dimension (W D H) ................... 375 393 267 mm
14 3/4 15 1/2 9 7/8"
Weight (without toner container) ..... 12 kg/26.5 lb
Power source.................................. 120 V AC, 60 Hz, 7.5 A
220 to 240 V AC, 50/60 Hz, 3.9 A
Power consumption ........................ 120 V AC model
Maximum: 910 W
During printing: 532 W
During standby: 11 W (EcoFuser ON), 67 W (EcoFuser OFF)
220 - 240 V AC model
Maximum: 967 W
During printing: 484 W
During standby: 12 W (EcoFuser ON), 75 W (EcoFuser OFF)
Options ........................................... Expanded memory, Paper feeder 2
Operating noise* ............................. During printing: LpA = 54 dB (A)
During standby: LpA = 30 dB (A)
During sleep mode: Immeasurably low.
*In accordance with ISO7779 (Bystander position, sound pressure level at the front)
1-1-2
2H4
1-1-2
Parts names
(1) Overall
3
2
4
8
10
16
12
11
7
5
9
13
15
14
Figure 1-1-1
1.
2.
3.
4.
5.
6.
7.
8.
Top cover
Paper stopper
Top tray
Operation panel
Right side cover
Cassette
Front cover
MP tray
9.
10.
11.
12.
13.
14.
15.
16.
Sub tray
Optional interface slot cover
USB interface connector
Network interface connector
Rear cover
Power cord connector
Power switch
USB memory slot
1-1-3
2H4
(2) Operation panel
Figure 1-1-2
1.
2.
3.
4.
5.
6.
7.
8.
9.
1-1-4
Ready indicator
Data indicator
Attention indicator
Message display
Cursor keys
GO key
CANCEL key
OK key
MENU key
2H4
1-1-3
12
10
13
Light path
Paper path
Paper path
(option)
Figure 1-1-3
1.
2.
3.
4.
5.
6.
Cassette
MP tray
Paper feed/conveying
section
Toner container
Developing unit
Main charger unit
7.
8.
9.
10.
11.
12.
13.
Drum unit
Laser scanner unit
Transfer/separation section
Fuser section
Paper exit section
Top tray
Duplex/conveying section
1-1-5
2H4
1-1-6
2H4
1-2 Installation
1-2-1
1.
2.
3.
4.
5.
6.
Installation environment
Temperature: 10 to 32.5C/50 to 90.5F
Humidity: 15 to 80%RH
Power supply: 120 V AC, 12 A
220 - 240 V AC, 7.2 A (Average)
Power source frequency: 50 Hz 0.3%/60 Hz 0.3%
Installation location
Avoid direct sunlight or bright lighting. Ensure that the photoconductor will not be exposed to direct sunlight or
other strong light when removing paper jams.
Avoid locations subject to high temperature and high humidity or low temperature and low humidity; an abrupt
change in the environmental temperature; and cool or hot, direct air.
Avoid places subject to dust and vibrations.
Choose a surface capable of supporting the weight of the machine.
Place the machine on a level surface (maximum allowance inclination: 1).
Avoid air-borne substances that may adversely affect the machine or degrade the photoconductor, such as mercury, acidic of alkaline vapors, inorganic gasses, NOx, SOx gases and chlorine-based organic solvents.
Select a well-ventilated location.
Allow sufficient access for proper operation and maintenance of the machine.
Machine front: 500 mm/19 11/16"
Machine rear: 200 mm/7 7/8"
Machine right: 300 mm/11 13/16"
Machine left: 300 mm/11 13/16"
Machine top: 200 mm/7 7/8"
200 mm
7 7/8"
300 mm
11 13/16"
300 mm
11 13/16"
200 mm
7 7/8"
500 mm
19 11/16"
Figure 1-2-1
1-2-1
2H4
1-2-2
Unpacking
120 V AC model
14
15
16
13
11
10
12
1
Figure 1-2-2
1.
2.
3.
4.
5.
6.
7.
8.
1-2-2
Printer
Outer case
Bottom pad L
Bottom pad R
Machine cover
Top pad L
Top pad R
Accessory spacer
9.
10.
11.
12.
13.
14.
15.
16.
Toner container
Plastic bag
Power cord
Rear right pad
Plastic bag
Installation guide
EEA information leaflet
Operation guide
2H4
(1) Removing the tapes
<Procedure>
1. Remove three tapes.
Tape
Tape
Tape
Figure 1-2-3
1-2-3
2H4
1-2-3
<Procedure>
1. Turn off printer power switch.
Caution: Do not insert or remove expanded
memory while printer power is on.
Doing so may cause damage to the printer
and the expanded memory.
2. Remove the right side cover.
3. Remove the tape.
Tape
Figure 1-2-4
4. Open the memory slot cover.
5. Insert the expanded memory into the memory socket so that the notches on the memory align with the corresponding protrusions
in the slot.
6. Close the memory slot cover.
7. Refit the right side cover.
8. Print a status page to check the memory
expansion (See page P.1-3-2).
If memory expansion has been properly performed, information on the installed memory
is printed with the total memory capacity has
been increased. Standard memory capacity
128 MB.
Memory socket
Expanded
memory
Figure 1-2-5
1-2-4
2H4
1-2-4
<Procedure>
1. Turn off printer power switch.
Caution: Do not insert or remove memory
card while printer power is on.
Doing so may cause damage to the printer
and the memory card.
2. Open the rear cover.
3. Remove two screws and then remove the
optional interface slot cover.
Rear cover
Screw
Optional interface
slot cover
Screw
Figure 1-2-6
4. Insert the memory card into the memory
card slot. Push it in all the way.
5. Secure the optional interface slot cover by
using two screws.
6. Close the rear cover.
7. Format the memory card before use.
Screw
Optional interface
slot cover
Figure 1-2-7
1-2-5
2H4
1-2-6
2H4
1-3 Maintenance Mode
1-3-1
Maintenance mode
The printer is equipped with a maintenance function which can be used to maintain and service the machine.
Message display
Ready
Report Print
>
Adjust/
Maintenance
>
>Restart
Printer
Press the or key several times
until [>Service >] is displayed.
>Service
>
>>Print
Status Page
>>Print Network
Status Page
>>Print
Test Page
>>Write data
>>Developer
1-3-1
2H4
(2) Contents of maintenance mode items
Maintenance items
Description
Printing a status page for service purpose
Description
Prints a status page for service purpose. The status page includes various printing settings and service cumulative.
Purpose
To acquire the current printing environmental parameters and cumulative information.
Procedure
1. Enter the maintenance mode [>>Print Status Page].
2. Press the OK key. [Print Status Page?] will be displayed.
3. Press the OK key. [Processing] will be displayed.
Two pages will be printed.
Completion
>>Print
Status Page
[XXXXXXXX][XXXXXXXX][XXXXXXXX[XXXXXXXX]
2008.09.27
Controller Information
Memory Status
Standard Size
Option Slot
Total Size
500.0 KB
500.0 KB
10000.0 KB
Time
Local Time Zone
Time Server
+01:00_Amsterdam
10.183.53.13
Y6
Installed Options
Paper feeder 2
Paper feeder 3
Memory Card
Installed
Installed
Installed
Toner coverage
Average(%) / Usage Page(A4/Letter Conversion)
K: 1.00
/ 1111111.00
Last Page (%) 1.00
FRPO Status
Default Pattern Switch
Default Font Number
FRPO parameters
B8
C5*10000+C2*100+C3
0
00000
[XXXXXXXXXXXXXXXX]
1-3-2
2H4
Maintenance items
Description
Details of service status page 1
No.
Items
Description
System version
System date
TIme server
Paper feeder 1
Paper feeder 2
FRPO setting
1-3-3
2H4
Maintenance items
Description
Service status page 2
2008.09.27
[XXXXXXXX][XXXXXXXX][XXXXXXXX[XXXXXXXX]
Engine Information
NVRAM Version
MAC Address
XXXXXXXXXXX
00.00.00.00.00.00
1/2
100/100
0/0/0/0/0/
0/0/0/0/0/
0/0/0/0/0/0/0/0/
0000000/0000000/0000000/0000000/0000000/0000000/
F00/U00/0/0/0/0/30/ABCDE/
0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/
0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/
0203040508090A0B0C0D0F101112131415161718191A1B1C1D1E1F202122235E
12345678/11223344/00001234abcd567800001234abcd5678/01234567890123456789012345678901/0008/00/07
XXXXXXXX
FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/
FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/
FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/
FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/
FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/
FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/
FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/
FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/FFFFFFFFFFFFFFFF/
00/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
00000000/00000000/00000000/00000000/
[ABCDEFGHIJ][ABCDEFGHIJ][ABCDEFGHIJ]
[XXXXXXXXXXXXXXXX]
1-3-4
2H4
Maintenance items
Description
Details of service status page 2
No.
Items
NV RAM version
Description
_ Bb 04B29 _ Bb 04B29
(a) (b)
(c) (d) (e)
(f)
(a) Consistency of the present software version and the database
_ (underscore): OK
* (Asterisk): NG
(b) Database version
(c) The oldest time stamp of database version
(d) Consistency of the present software version and the ME firmware
version
_ (underscore): OK
* (Asterisk): NG
(e) ME firmware version
(f) The oldest time stamp of the ME database version
Normal if (a) and (d) are underscored, and (b) and (e) are identical with
(c) and (f).
Mac address
Destination information/Area
information
Margin settings
0/0
(a)(b)
0/0/0/0/0
(a)(b)(c)(d)(e)
(a) MP tray
(b) Cassette 2
(c) Cassette 3
(d) Duplex
(e) Page rotation
0/0/0/0/0
(a)(b)(c)(d)(e)
(a) MP tray
(b) Cassette 2
(c) Cassette 3
(d) Duplex
(e) Page rotation
L value settings
0/0/0/0/0/0/0/0
(a)(b)(c)(d)(e)(f)(g)(h)
Life counter
0000000/0000000/0000000/0000000/0000000/0000000/
(a) (b) (c)
(d) (e) (f)
(a) Printer
(b) MP tray
(c) Cassette 1
(d) Cassette 2
(e) Cassette 3
(f) Duplex printing
1-3-5
2H4
Maintenance items
No.
Description
Items
Description
0: Off
1: Partial lock
2: Full lock
USB information
0: Not connected
1: Full-Speed
2: Hi-Speed
Media type
Weight
0: Light
1: Normal 1
2: Normal 2
3: Normal 3
4: Heavy 1
5: Heavy 2
6: Heavy 3
7: Extra Heavy
SPD information
RFID information
Fuser
0: Hi
1: Middle
2: Low
3: Vellum
Duplex
0: Disable
1: Enable
NOTE:
Code conversion
1-3-6
2H4
Maintenance items
>>Print Network
Status Page
Description
Printing a status page for network
Description
On the status page for network, detailed network setting information is printed.
Procedure
1. Enter the maintenance mode [>>Print Network Status Page].
2. Press the OK key. [>>Print Network Status Page?] will be displayed.
3. Press the OK key. Three sheets of network status page will be printed.
Completion
>>Print
Test Page
FS-1350DN
SN:SPL8307597
Counter:1135
Figure 1-3-3
>>Write Data
1-3-7
2H4
Maintenance items
>>Developer
1-3-8
Description
Toner install mode
Description
The new developing unit is shipped from the factory with no toner contained. The developing unit can be automatically replete with toner when a toner container is installed onto it
and the printer is turned on. However, because the toner reservoir in the developing unit
has a large capacity, it requires a lengthy period of time until a substantial amount of toner
has been fed to get the printer ready. (A new developing unit needs approximately 260 g
for triggering the sensor inside.)
Purpose
To execute when the developing unit has been replaced.
Method
1. Enter the maintenance mode [>>Developer].
2. Press the OK key. [>>Developer?] will be displayed.
3. Press the OK key. [Ready] will be displayed.
4. Turn off and on the printer. [Self test] [Please wait (Adding toner)] will displayed.
The printer continually engages in this mode for a period of approximately 15
minutes, after which the printer reverts to the [Ready] state. [Ready] will displayed. Developing unit initialization is finished.
Completion
2H4
(3) Printing an event log (EVENT LOG)
Service items
Printing an event log
(EVENT LOG)
Description
Printing an event log (EVENT LOG)
Description
Prints a history list of occurrences of paper jam, self-diagnostics, toner replacements, etc.
Purpose
To allow machine malfunction analysis based on the frequency of paper misfeeds, self diagnostic errors and replacements.
Procedure
1. Connect the USB or network cable between printer and PC (network).
2. Connect the power cord.
Network interface
connector
Network cable
USB interface
connector
USB cable
Figure 1-3-4
3. Turn printer power on. Make sure the printer is ready.
4. Send the following PRESCRIBE command sequence from the PC to the printer.
!R!KCFG"ELOG";EXIT;
Note: To send a PRESCRIBE command sequence to the printer, use COMMAND
CENTER (the printer's embedded web) while the printer is connected to the PC via its
network interface.
A sheet of event log will be printed.
Completion
1-3-9
2H4
Service items
Description
Detail of event log
Event Log
Printer
Firmware Version 2H4_2000.000.000 2008.08.08
Count.
9999999
8888888
7777777
6666666
5555555
4444444
3333333
2222222
1111111
999999
888888
777777
666666
555555
444444
1
Event Descriptions
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
10. 48. 01. 88. 01. 01
#
8
7
6
5
4
3
2
1
(b)
(c)
(d)
(e)
Service Code
00. 0000
00. 0000
00. 0000
00. 0000
00. 0000
00. 0000
00. 0000
00. 0000
Maintenance Log
#
Count.
Item
Log Data Nothing...
Count.
1111111
999999
888888
777777
666666
555555
444444
1
#
5
4
3
2
1
(f)
Count.
1111111
999999
888888
777777
666666
Item
00. 00
00. 00
00. 00
00. 00
00. 00
Counter Log
(g)
J00:
0
J01:
1
J02: 11
J03: 222
J04:
1
J05:
1
J06:
1
J07:
1
J08:
1
J09:
1
J10:
1
J12: 999
J13:
J14:
J15:
J16:
J17:
J18:
J19:
J20:
J21:
J22:
J23:
J24:
1
1
1
1
1
1
1
1
1
1
1
1
J25:
J26:
J27:
J28:
J29:
J30:
J31:
J32:
J33:
J34:
J35:
J36:
1
1
1
1
1
1
1
1
1
1
1
1
(h)
C0000:
C0001:
C0002:
C0003:
C0004:
C0005:
C0006:
C0007:
C0008:
C0009:
C0010:
C0011:
0
1
2
3
4
5
6
7
8
9
10
11
C0012:
C0013:
C0014:
C0015:
C0016:
C0017:
C0018:
C0019:
C0020:
C0021:
C0022:
C0023:
12
13
14
15
16
17
18
19
20
21
22
23
(i)
T00:
M01:
10
20
[XXXXXXXXXXXXXXXX]
1-3-10
2H4
Service items
No.
Description
Items
Description
Firmware version
Count.
Event
Remembers 1 to 16 of
occurrence. If the
occurrence of the previous paper jam is less
than 16, all of the paper
jams are logged. When
the occurrence
excessed 16, the oldest occurrence is
removed.
1-3-11
2H4
Service items
No.
cont.
Description
Items
Description
(a) Cause of paper jam
10: Paper does not arrive at the registration sensor. [42] (MP tray)
10: Paper does not arrive at the registration sensor. [31] (Cassette 1)
10: Paper does not arrive at the registration sensor. [31] (Cassette 2)
10: Paper does not arrive at the registration sensor. [31] (Cassette 3)
10: Paper does not arrive at the registration sensor. [49] (Duplex conveying)
11: Paper does not pass the registration sensor. [48]
12: Paper remains at the registration sensor when power is turned on. [48]
20: Paper does not arrive at the exit sensor. [48]
21: Paper does not pass the exit sensor. [47]
22: Paper remains at the exit sensor when power is turned on. [47]
30: Paper does not arrive at the paper feeder 1s PF paper feed sensor. [32](Cassette 2)
30: Paper does not arrive at the paper feeder 1s PF paper feed sensor. [33] (Cassette 3)
31: Paper does not arrive at the paper feeder 1s PF paper feed sensor. [32] (Cassette 2)
32: Paper remains at the paper feeder 1s PF paper feed sensor when power is turned on.
[32] (Cassette 2)
40: Paper does not arrive at the paper feeder 2s PF paper feed sensor. [33] (Cassette 3)
41: Paper does not pass the paper feeder 2s PF paper sensor. [33] (Cassette 3)
42: Paper remains at the paper feeder 2s PF paper feed sensor when power is turned on.
[33] (Cassette 3)
A1: Paper does not arrive at the exit sensor. [47]
A3: Paper does not pass the exit sensor. [49]
E0: Paper misfeed occurs due to forced stop when an error occurs during printing. (such as
opening of a cover) [00]
F0 to FE: Paper misfeed by another cause. [00]
Note:
Within [ ] indicate paper misfeed locations. (Refer to figure 1-3-6 below.)
(b) Detail of jam location
Printer
Sensors
47
42
3
48
4
49
2
31
1 Registration
sensor
2 Paper sensor
3 MP paper
sensor
4 Exit sensor
5 PF paper feed sensor
6 PF paper sensor
Paper misfeed locations
32
Paper feeder 1
31 Cassette 1 (Printer)
32 Cassette 2 (Paper feeder 1)
Paper feeder 2
Figure 1-3-6
1-3-12
2H4
Service items
No.
Description
Items
cont.
Description
(c) Detail of paper source (Hexadecimal)
00: MP tray
01: Cassette 1 (Printer)
02: Cassette 2 (Paper feeder 1)
03: Cassette 3 (Paper feeder 2)
04 to 09: (d) Detail of paper size (Hexadecimal)
00: (indefinite)
01: Monarch
02: Business
03: International DL
04: International C5
05: Executive
06: Letter-R
86: Letter-E
07: Legal
08: A4R
88: A4E
09: B5R
89: B5E
0A: A3
0B: B4
0C: Ledger
0D: A5
0E: A6
0F: B6
10: Commercial #9
11: Commercial #6
12: ISO B5
13: Custom size
1E: C4
1F: Postcard
20: Reply-paid postcard
21: Oficio II
22: Special 1
23: Special 2
24: A3 wide
25: Ledger wide
26: Full bleed paper
(12 8)
27: 8K
28: 16K-R
A8: 16K-E
32: Statement-R
B2: Statement-E
33: Folio
34: Western type 2
35: Western type 4
0A: Color
0B: Prepunched
0C: Envelope
0D: Cardstock
0E: Coated
0F: 2nd side
10: Media 16
11: High quality
15: Custom 1
16: Custom 2
17: Custom 3
18: Custom 4
19: Custom 5
1A: Custom 6
1B: Custom 7
1C: Custom 8
Service Call
(Self diagnostic
error) Log
Count.
Service Code
Remembers 1 to 8 of
occurrence of self diagnostics error. If the
occurrence of the previous diagnostics error is
less than 8, all of the
diagnostics errors are
logged.
1-3-13
2H4
Service items
No.
Description
Items
Maintenance
Log
Unknown Toner
Log
Description
#
Count.
Item
Remembers 1 to 8 of
occurrence of replacement. If the occurrence of
the previous replacement
of toner container is less
than 8, all of the occurrences of replacement
are logged.
Count.
Item
Remembers 1 to 5 of
occurrence of unknown
toner detection.
Counter Log
Comprised of
three log
counters including paper jams,
self diagnostics
errors, and
replacement of
the toner container.
1-3-14
First byte
01: Fixed (Toner container)
Second byte
00: Black (Fixed)
(g) Jam
Example
C6000: 4
Self diagnostics error
6000 has happened four
times.
T: Toner container
00: Black
Example
T00: 1
The (black) toner container has
been replaced once.
2H4
1-4 Troubleshooting
1-4-1
Paper jam
Printer
Figure 1-4-1
(2) Paper misfeed detection condition
Registration sensor
Paper sensor
MP paper sensor
Exit sensor
PF paper feed sensor
PF paper sensor
Printer
Peper feeder 1
(Option)
Peper feeder 2
(Option)
Figure 1-4-2
1-4-1
2H4
1-4-2
Self-diagnostic function
Error code
Call service
6000:012345
Error code
Call service
F000
Attention indicator
Error code
Error.power off.
F030
Figure 1-4-3
1-4-2
2H4
(2) Self diagnostic codes
Code
Remarks
Contents
Causes
0100
0110
Defective flash
memory (U10).
Defective control
PWB.
Defective flash
memory (U10).
Defective control
PWB.
0120
Defective flash
memory (U10).
0150
Defective control
PWB.
0170
Defective control
PWB.
0420
Defective harness
between control
PWB (YC318) and
paper feeder interface connector, or
improper connector insertion.
Reinsert the connector. Also check for continuity within the connector harness. If none,
remedy or replace the harness.
Defective control
PWB.
Defective harness
between PF main
PWB (YC5) and
paper feeder interface connector, or
improper connector insertion.
Reinsert the connector. Also check for continuity within the connector harness. If none,
remedy or replace the harness (Refer to the
service manual for the paper feeder).
1-4-3
2H4
Code
2000
4000
4200
6000
6020
1-4-4
Remarks
Contents
Main motor error
The main motor ready input is not given
for 2 s during the main motor is ON.
Causes
Defective harness
between main
motor (CN1) and
control PWB
(YC305), or
improper connector insertion.
Reinsert the connector. Also check for continuity within the connector harness. If none,
remedy or replace the harness.
Defective drive
transmission system of the main
motor.
Defective main
motor.
Defective control
PWB.
Defective harness
between polygon
motor and control
PWB (YC319), or
improper connector insertion.
Reinsert the connector. Also check for continuity within the connector harness. If none,
remedy or replace the harness.
Defective laser
scanner unit.
Defective control
PWB.
Defective laser
scanner unit.
Defective control
PWB.
Fuser thermistor
installed incorrectly.
Broken fuser
heater lamp wire.
Defective control
PWB.
2H4
Code
Remarks
Contents
Causes
6030
6400
F000
F010
Fuser thermistor
installed incorrectly.
Broken fuser
heater lamp wire.
Defective harness
between high voltage PWB (YC202)
and control PWB
(YC311), or
improper connector insertion.
Reinsert the connector. Also check for continuity within the connector harness. If none,
remedy or replace the harness (See page 15-24).
Defective harness
between power
source PWB
(YC103) and high
voltage PWB
(YC201), or
improper connector insertion.
Reinsert the connector. Also check for continuity within the connector harness. If none,
remedy or replace the harness (See page 15-24).
Defective power
source PWB.
Defective control
PWB.
Defective harness
between operation
panel PWB (YC1)
and control PWB
(YC7), or improper
connector insertion.
Reinsert the connector. Also check for continuity within the connector harness. If none,
remedy or replace the harness (See page 15-24).
Defective control
PWB.
Defective code
ROM (flash memory).
Defective control
PWB.
1-4-5
2H4
Code
Remarks
Contents
Causes
F020
Defective main
memory (RAM) on
the control PWB.
Defective
expanded memory
(DIMM).
F030
Defective control
PWB.
F040
Defective control
PWB.
F050
Defective control
PWB.
Defective control
PWB.
F186
1-4-6
2H4
1-4-3
(1)Completely blank
printout.
(2)All-black printout.
(3)Dropouts.
ABC
123
(6)Black vertical
streaks.
(7)Unsharpness.
ABC
123
(4)Black dots.
ABC
123
(8)Gray background.
ABC
123
ABC
123
(5)Black horizontal
streaks.
ABC
123
This vertical
line should
be straight.
1-4-7
2H4
(1) Completely blank printout.
Print example
Causes
Open the top cover and check that the drum unit and developing unit are correctly seated. Investigate that the terminals
between the main charger unit and the drum unit are not in
loose contact (See page 1-5-12 and 1-5-11).
Poor contact of developing bias termi- Check the high voltage PWB visually and correct or replace if
nal (spring) and high voltage output
necessary (See page 1-5-24).
terminal B (J401, J402, J403) on the
high voltage PWB.
Poor contact of transfer bias terminal
(spring) and transfer bias terminal T
(J201, J202, J203) on the high voltage PWB.
Defective laser scanner unit.
1-4-8
Causes
Open the top cover and check that the drum unit and developing unit are correctly seated (See page 1-5-12).
Investigate that the terminals between the main charger unit
and the drum unit are not in loose contact.
2H4
(3) Dropouts.
Print example
ABC
123
Causes
Replace the high voltage PWB or control PWB (See page 1-524 or 1-5-19).
ABC
123
Causes
Defective drum unit or developing
unit.
ABC
123
Causes
Check that the drum shaft and the grounding tab (printer) are
in good contact. Apply the grounding tab a small amount of
electroconductive grease as required.
1-4-9
2H4
(6) Black vertical streaks.
Print example
ABC
123
Causes
Remove the drum unit (See page 1-5-12). Slide the charger
cleaner (green) left and right 2 or 3 times to clean the charger
wire, then return it to its original position (CLEANER HOME
POSITION). Refer to the operation guide.
(7) Unsharpness.
Print example
Causes
Replace paper with the one that satisfies the paper specification.
Replace the high voltage PWB or control PWB (See page 1-524 or 1-5-19).
ABC
123
1-4-10
Causes
The print density may be set too high. Try adjusting the print
density. For details, refer to the operation guide.
If a developing unit which is known to work normally is available for check, replace the current developing unit in the
printer with the normal one. If the symptom disappears,
replace the developing unit with a new one (See page 1-5-11).
2H4
(9) Dirt on the top edge or back of the paper.
Print example
Causes
If the transfer roller is contaminated with toner, clean the transfer roller using a vacuum cleaner or by continuously printing a
low density page until the symptom has faded away.
ABC
123
Causes
This vertical
line should
be straight.
1-4-11
2H4
1-4-4
Electric problems
Problem
(4)Registration clutch
does not operate.
1-4-12
Causes
Check the contact between the power plug and the outlet.
Check for continuity across the coil. If none, replace the right cooling fan motor.
Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Check for continuity across the coil. If none, replace the left cooling fan motor.
Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Check for continuity across the coil. If none, replace the registration clutch.
Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Check for continuity across the coil. If none, replace the paper
feed clutch.
Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
2H4
Problem
(6)developing clutch
does not operate.
Causes
Check for continuity across the coil. If none, replace the developing clutch.
Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Broken MP paper feed sole- Check for continuity across the coil. If none, replace the MP paper
noid coil.
feed solenoid.
Defective harness between
MP paper feed solenoid
and control PWB (YC309),
or improper connector
insertion.
Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Check for continuity across the coil. If none, replace the duplex
solenoid.
Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
(10)Paper indicator is
flashing when paper
is present in the cassette.
Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness.
(8)Duplex solenoid
does not operate.
(Duplex model only)
Check for continuity across the interlock switch. If there is no continuity when the interlock switch is on, replace the power source
PWB (See page 1-5-22).
1-4-13
2H4
1-4-5
Mechanical problems
Problem
Causes/check procedures
Corrective measures
(4)Multiple sheets of
paper are fed at one
time.
(5)Paper jams.
(7)Abnormal noise is
heard.
1-4-14
2H4
1-5 Assembly and Disassembly
1-5-1
(1) Precautions
Be sure to turn the power switch off and disconnect the power plug before starting disassembly.
When handling PWBs, do not touch connectors with bare hands or damage the PWB.
Do not touch any PWB containing ICs with bare hands or any object prone to static charge.
When removing the hook of the connector, be sure to release the hook.
Take care not to get the wire caught.
(2) Drum
Note the following when handling or storing the drum.
When removing the drum unit, never expose the drum surface to strong direct light.
Keep the drum at an ambient temperature between 0 C/32 F and 40 C/104 F and at a relative humidity not higher than
90% RH. Avoid abrupt changes in temperature and humidity.
Avoid exposure to any substance which is harmful to or may affect the quality of the drum.
Do not touch the drum surface with any object. Should it be touched by hands or stained with oil, clean it.
(3) Toner container
Store the toner container in a cool, dark place.
Avoid direct light and high humidity.
1-5-1
2H4
(4) How to tell a genuine Kyocera Mita toner container
As a means of brand protection, the Kyocera Mita toner container utilizes an optical security technology to enable visual
validation. A validation viewer is required to accomplish this.
Hold the validation viewer over the left side part of the brand protection seal on the toner container. Through each window
of the validation viewer, the left side part of the seal should be seen as follows:
A black-colored band when seen through the left side window
A shiny or gold-colored band when seen through the right side window
The above will reveal that the toner container is a genuine Kyocera Mita branded toner container, otherwise, it is a counterfeit.
See through
the left window
( marking)
See through
the right window
( marking)
Validation viewer
Validation viewer
Figure 1-5-1
The brand protection seal has an incision as shown below to prohibit reuse.
Incision
Cut
Figure 1-5-2
1-5-2
2H4
1-5-2
Outer covers
Top cover
Screw
Screw
Figure 1-5-3
3.
4.
5.
6.
7.
Top cover
Hole
Boss
B hook
B hook
Top cover
Connector
A hook
Figure 1-5-4
1-5-3
2H4
(2) Detaching and refitting the right and left covers
Procedure
1. Remove the top cover (See page 1-5-3).
2. Remove the cassette (See page 1-5-6).
3. Open the front cover.
4. Unhook seven hooks and then remove the
right cover.
Hooks
Right cover
Figure 1-5-5
1-5-4
2H4
Left cover
Hooks
Figure 1-5-6
1-5-5
2H4
1-5-3
(1) Detaching and refitting the paper feed roller assembly (paper feed roller and pickup roller)
Procedure
1. Remove the cassette.
Cassette
Figure 1-5-7
2. Slide the feed shaft.
3. While pressing the lever and then remove
the paper feed roller assembly.
Feed shaft
Figure 1-5-8
1-5-6
2H4
Feed shaft
Slotted hole
Pivot
Figure 1-5-9
1-5-7
2H4
(2) Detaching and refitting the retard roller assembly
Procedure
1. Remove the cassette (See page 1-5-6).
2. Push the bottom plate down until it locks.
3. Unhook two hooks and then remove the
retard guide.
Retard guide
Hook
Hook
Cassestte
Bottom plate
Cassette
Hook
Hook
Figure 1-5-10
4. Remove the retard roller assembly.
Retard roller
Assembly
Figure 1-5-11
1-5-8
2H4
Retard roller
assembly
Projection
Spring
Figure 1-5-12
1-5-9
2H4
(3) Detaching and refitting the MP paper feed roller
Procedure
1. Open the front cover.
2. Pull the MP feed holder (lever) down ().
3. Slide the MP feed holder ().
4. Remove the MP paper feed roller ().
MP paper feed roller
Front cover
MP feed holder
(Lever)
Figure 1-5-13
5. Check or replace the MP paper feed roller
and refit all the removed parts.
When refitting the MP paper feed roller, be
sure to align the MPF feed shaft pivot with
the slotted hole on the MP paper feed roller.
Pivot
Slotted hole
Figure 1-5-14
1-5-10
2H4
1-5-4
Developing section
Top cover
Developing unit
Front cover
Figure 1-5-15
1-5-11
2H4
1-5-5
Drum section
Drum unit
Figure 1-5-16
1-5-12
2H4
(2) Detaching and refitting the main charger unit
Procedure
1. Remove the drum unit (See page 1-5-12).
2. Remove the tape.
3. While pushing on the main plate (), slide
the main charger unit ().
Tape
Main charger unit
Drum unit
Main plate
Figure 1-5-17
4. Remove the main charger unit by lifting it.
5. Check or replace the main charger unit and
refit all the removed parts.
Main charger unit
Figure 1-5-18
1-5-13
2H4
1-5-6
Transfer/separation section
Hook
Hook
Hook
Figure 1-5-19
1-5-14
2H4
Shaft
Transfer roller
Shaft
Transfer bush
Transfer bush
Transfer roller
Gear Z16
Figure 1-5-20
7. Check or replace the transfer roller and refit
all the removed parts.
Caution: When refitting the transfer roller, be
careful about following point.
Push the release lever to raise the lever
end, then insert the front of gear Z16 under
the release lever end.
Gear Z16
Release lever
Transfer bush
Transfer roller
Transfer bush
Figure 1-5-21
1-5-15
2H4
1-5-7
Fuser section
Wires
Wire clamps
Connector
(Fuser heater lamp)
Connector
(Fuser thermistor)
Figure 1-5-22
4. Remove the connector.
Connector
Figure 1-5-23
1-5-16
2H4
Rear cover
Figure 1-5-24
6. Remove two screws and then remove the
fuser unit.
7. Check or replace the fuser unit and refit all
the removed parts.
Fuser unit
Screw
Screw
Figure 1-5-25
1-5-17
2H4
(2) Switching the fuser pressure
The fuser pressure may be decreased to suppress the print quality problems such as paper creases and curls.
It must be cautioned that decreasing the fuser pressure could cause loose toner fusing.
Procedure
1. Remove the cassette (See page 1-5-6).
2. Open the duplex cover.
3. Slide the fuser lever R and L.
Normal:
Flush with the front of the machine.
Fuser pressure decreased:
Flush with the rear of the machine.
Fuser lever R
Duplex cover
Fuser lever L
Normal
Figure 1-5-26
1-5-18
2H4
1-5-8
PWBs
Control PWB
Wire clamps
Connectors
(Twelve)
Connector
Control PWB
Figure 1-5-27
1-5-19
2H4
Connectors
(Four)
Control PWB
Hook
Screw
Screws
Figure 1-5-28
1-5-20
Screws
2H4
Screw
Screw
Screw
Screw
Control PWB
Screw
EEPROM
U300
Control PWB
Figure 1-5-29
1-5-21
2H4
(2) Detaching and refitting the power source PWB
Procedure
1. Remove the left cover (See page 1-5-4).
2. Remove four connectors.
Connector
Connector
Connector
Connector
Figure 1-5-30
3. Remove four P tight screws, two screws and
ground terminal.
4. Remove the power source PWB assembly
from the high voltage PWBs connector.
Ground
terminal
Connector
(YC201)
High voltage PWB
Screws
Connector
(YC103)
P tight screws
Power source
PWB assembly
P tight screws
Figure 1-5-31
1-5-22
2H4
Screws
Screws
Figure 1-5-32
1-5-23
2H4
(3) Detaching and refitting the high voltage PWB
Procedure
1. Remove the developing unit (See page 1-511).
2. Remove the drum unit (See page 1-5-12).
3. Remove the cassette (See page 1-5-6).
4. Remove the outer covers (See page 1-5-3).
5. Remove the power source PWB (See page
1-5-22).
6. Turn the printer with the bottom side up.
7. Remove the stop ring.
8. Remove the DU holder.
Stop ring
DU holder
Figure 1-5-33
9. Pull out the DU bush.
10. Remove the DU cover assembly.
DU cover assembly
DU bush
Figure 1-5-34
1-5-24
2H4
Hook
Hook
Hook
Screws
Screws
Lower base cover
Figure 1-5-35
1-5-25
2H4
Cassette pin
Spring
Figure 1-5-36
15. Remove two connectors and then remove
the high voltage PWB.
16. Remove the cassette pin holder from the
high voltage PWB.
High voltage
PWB
Cassette pin
holder
YC202
YC203
Connector
Connector
Figure 1-5-37
1-5-26
2H4
OK
NG
Ground plate
Spring
(Developing)
Spring
(Transfer)
Spring
(separation)
Spring
(Main charger)
Bias
contact pin
High voltage
PWB
Cassette pin
Figure 1-5-38
1-5-27
2H4
1-5-9
Others
Connector
Figure 1-5-39
3. Remove the M3 screw and two M4 screws.
4. Remove the main motor.
5. Check or replace the main motor and refit all
the removed parts.
M3 Screw
Main motor
Figure 1-5-40
1-5-28
M4 screws
2H4
(2) Detaching and refitting the laser scanner unit
Procedure
1. Remove the right cover (See page 1-5-4).
2. Remove the connector from the control
PWB.
3. Release the wire clamp.
4. Draw in the connector inside.
Connector
Control PWB
Wire clamp
Connector
Figure 1-5-41
1-5-29
2H4
Screws
Screws
Figure 1-5-42
1-5-30
2H4
(3) Detaching and refitting the eraser lamp (PWB)
Procedure
1. Remove the laser scanner unit (See page 15-29).
2. Remove the connector.
3. Slide the eraser holder.
4. Unhook the hooks and then remove the
eraser holder.
Connector
Eraser holder
Hooks
Eraser holder
Hooks
Hooks
Hook
Figure 1-5-43
5. Remove the eraser lamp (PWB) from the
eraser holder.
6. Check or replace the eraser lamp (PWB)
and refit all the removed parts.
Eraser lamp (PWB)
Eraser holder
Figure 1-5-44
1-5-31
2H4
(4) Direction of installing the left cooling fan motor and right cooling fan motor
When detaching or refitting the left cooling fan motor or right cooling fan motor, be careful of the airflow direction (intake or
exhaust).
Right cooling
fan motor
Left cooling
fan motor
Intake
Exhaust
Figure 1-5-45
1-5-32
2H4
1-6 Firmware
1-6-1
Downloading firmware
Engine firmware
Master download file
DL_ENGN.2H4
S2H4_1000000024.x
Extention
Software ID
Build number
Product code
2H4= This printer
Update history
Classification (Normally: 0)
Pause (underscore)
System firmware
Master download file
DL_CTRL.2H4
2H4_3000.000.088.bin
2H4_3100.000.004.hex
Product code
2H4= This printer
Extention
Build number
Update history
Pause (underscore)
Classification (Normally: 0)
Supplement (Normally: 00)
Firmware category
30: System (Main)
31: System (BROM)
Figure 1-6-1
1-6-1
2H4
(2) Downloading the firmware from the USB memory
To download data written in a USB memory to the printer, proceed as explained in this section.
CAUTION
Downloading firmware takes several minutes. Do not turn power off during downloading. If downloading is interrupted by
an accidental power failure, etc., the control PWB may have to be replaced.
Procedure
1. Turn printer power off.
2. Insert the USB memory to the PC's USB
slot.
3. Copy the firmware files to download to the
root directory of the USB memory.
4. Remove the USB memory from the PC's
USB slot.
5. Insert the USB memory into the printer's
USB memory slot.
USB memory
slot
USB memory
Figure 1-6-2
6. Turn printer power on.
7. When message display (1) is displayed to
detect firmware in the USB memory.
8. Message display (2) is displayed during
downloading.
9. When message display (3) is displayed to
indicate downloading is finished.
Message display
(1)
supervisor mode
(2)
supervisor mode
USB data reading
(3)
2H4_1000.000.024
[E1F9]
Product code
2H4= This printer
Firmware category
10: Engine
30: System (Main)
31: System (BROM)
Supplement (Normally: 00)
Classification (Normally: 0)
Update history
Build number
Checksum
Figure 1-6-3
1-6-2
2H4
USB memory
slot
USB memory
Figure 1-6-4
1-6-3
2H4
(3) Downloading the firmware from the memory card
To download data written in a memory card (CompactFlash) to the printer, proceed as explained in this section.
CAUTION
Downloading firmware takes several minutes. Do not turn power off during downloading. If downloading is interrupted by
an accidental power failure, etc., the control PWB may have to be replaced.
Procedure
1. Turn printer power off.
2. Open the rear cover.
3. Remove two screws and then remove the
optional interface slot cover.
4. Insert the memory card into the memory
card slot.
Screw
Optional interface
slot cover
Figure 1-6-5
5. Turn printer power on.
6. Press MENU key on the printer's operation
panel and carry out the memory card formatting procedure (1).
7. When formatting is complete, turn printer
power off.
Message display
Ready
>Memory Card
>
Press arrow key.
>>Format
Press OK key.
(1)
>>Format ?
Press OK key.
Processing
(Format information is
automatically printed.)
Ready
Figure 1-6-6
1-6-4
2H4
Memory card
Figure 1-6-7
9. Insert the memory card to the PC's slot or to
the adaptor.
10. Copy the firmware files to download to the
root directory of the memory card.
11. Remove the memory card from the PC's slot
or the adaptor.
Adapter
(Memory card reader)
Memory card
To PC
Figure 1-6-8
12. Insert the memory card into the memory
card slot.
Memory card
Figure 1-6-9
1-6-5
2H4
Message display
(1)
supervisor mode
(2)
supervisor mode
CF-card reading
(3)
2H4_1000.000.024
[E1F9]
Product code
2H4= This printer
Firmware category
10: Engine
30: System (Main)
31: System (BROM)
Supplement (Normally: 00)
Classification (Normally: 0)
Update history
Build number
Checksum
Figure 1-6-10
17. Turn printer power off.
18. Remove the memory card from memory
card slot.
19. Refit the optional interface slot cover.
20. Turn printer power on.
21. Print the status page to check that the firmware version has been updated.
(See page P.1-3-7)
Screw
Option interface
slot cover
Figure 1-6-11
1-6-6
2H4
2-1 Mechanical Construction
2-1-1
Paper feed/conveying section consists of the paper feed unit that feeds paper from the cassette and the MP tray paper
feed unit that feeds paper from the MP tray, and the paper conveying section that conveys the fed paper to the transfer/
separation section.
(1) Cassette paper feed section
10
6
8
7
11
5
9
Pickup roller
Paper feed roller
Feed holder
Retard roller
Retard holder
Retard guide
(7)
(8)
(9)
(10)
(11)
Bottom plate
Bottom pad
Cassette base
Paper sensor
Actuator (paper sensor)
Control PWB
MMOTRDYN
MOTCLK
Main motor
REMOTEN
Paper feed
Clutch
Paper sensor
FEDDRN
PAPER
YC331-3
YC331-4
YC331-5
YC334-4
YC332-3
2-1-1
2H4
(2) MP tray paper feed section
6
8
1
2
3
7
11
4
12
10
13
(8)
(9)
(10)
(11)
(12)
(13)
MPF frame
MPF guide R/L
MPF base
MPF middle tray
MPF upper tray
MPF turn guide
Control PWB
MMOTRDYN
MOTCLK
Main motor
REMOTEN
MP paper
feed solenoid
MP paper sensor
YC331-3
YC331-4
YC331-5
MPFDRN
YC335-2
HANDSN
YC330-3
2-1-2
2H4
(3) Paper conveying section
2
1
4
5
3
Control PWB
MMOTRDYN
MOTCLK
Main motor
REMOTEN
Registration
clutch
REGDRN
YC331-3
YC331-4
YC331-5
YC334-2
Registration
sensor
REGN
YC337-11
2-1-3
2H4
2-1-2
Drum section
3
4
2-1-4
Drum
Drum shaft
Drum cover A
Drum cover B
2H4
(2) Main charger unit
As the drum rotates in a clean (neutral) state, its photoconductive layer is given a uniform, positive (+) corona charge dispersed by the main charger wire. Due to high-voltage scorotron charging, the charging wire can get contaminated by oxidization after a long run. Therefore, the charger wire must be cleaned at a specific interval. Cleaning the charging wire
prevents print quality problems such as black streaks.
1
2
Zener
PWB
High voltage
PWB
Drum
Figure 2-1-9 Drum unit and main charger unit block diagram
2-1-5
2H4
2-1-3
Expose section
5
1
2-1-6
2H4
10
7
8
9
6
2-1-7
2H4
2-1-4
Developing section
The latent image constituted on the drum is developed into a visible image. The developing roller contains a 3-pole (S-NS) magnet roller and an aluminum cylinder rotating around the magnet roller. Toner attracts to the magnet sleeve since it is
powdery ink made of black resin bound to iron particles. Developing blade, magnetized by magnet, is positioned approximately 0.3 mm above the magnet sleeve to constitute a smooth layer of toner in accordance with the magnet sleeve revolution.
The developing roller is applied with the AC-weighted, positive DC power source. Toner on the magnet sleeve is given a
positive charge. The positively charged toner is then attracted to the areas of the drum which was exposed to the laser
light. (The gap between the drum and the magnet sleeve is approximately 0.32 mm.) The non-exposed areas of the drum
repel the positively charged toner as these areas maintain the positive charge.
The developing roller is also AC-biased to ensure contrast in yielding by compensating the toners attraction and repelling
action during development.
1
7
2
5
Magnet sleeve
Magnet roller
Developing blade
Blade magnet
(5)
(6)
(7)
(8)
DLP screw A
DLP screw B
DLP case
Toner container
Developing
roller
Control PWB
Magnet roller
Magnet sleeve
Developing
clutch
DLPDRN
YC334-6
2-1-8
2H4
2-1-5
Transfer/separation section
The transfer/separation section consists of the transfer roller, discharger brush and paper chute guide. A high voltage generated by the high voltage PWB is applied to the transfer roller for transfer charging. Paper after transfer is separated from
the drum.
3
1
4
Transfer roller
Transfer bushes
Discharger brush
DC brush holder
Paper chute guide
High voltage
PWB
Discharger
brush
Transfer
roller
Transfer bias
Separation bias
2-1-9
2H4
2-1-6
Cleaning section
After the transferring process, the drum needs to be physically cleaned of toner which is residual after the development
process. The cleaning blade is constantly pressed against the drum and scrapes the residual toner off to the sweep roller.
The waste toner is collected at the output end of the sweep roller and sent back to the toner container, into the waste toner
reservoir.
After the drum is physically cleaned, it then must be cleaned to the electrically neutral state. This is necessary to erase any
residual positive charge, ready to accept the uniform charge for the next print process. The residual charge is canceled by
exposing the drum to the light emitted from the eraser lamp (PWB). This lowers the electrical conductivity of the drum surface making the residual charge on the drum surface escape to the ground.
Main frame
1
2
3
4
Drum unit
ERASER
Eraser
lamp
(PWB)
Drum
YC342-1
Control PWB
2H4
2-1-7
Fuser section
The toner on the paper is molten and pressed into the paper as it passes between the heat roller and the press roller in the
fuser unit. The heat roller has a heater lamp inside which continuously turns on and off by the fuser thermistor to maintain
the constant temperature onto the heat roller surface. The heat roller is resin coated by florin to prevent toner from accumulating on the roller after a long run. Care must be taken while handling the heat roller not to scratch the roller surface as
doing so may result in print problems. Fuser temperature is optimized to the paper type. The heat roller has four separators (claws) which are continuously in contact with its surface. These separators (claws) prevent the paper on which toner
has been fused from being wound around the heat roller causing paper jam. The press roller is made of the heat-resistant
silicon rubber. This roller is used to strongly press the paper towards the heat roller by means of press springs. The temperature of the heat roller is constantly monitored by the control PWB using the fuser thermistor. Should the temperature
of the heat roller exceed the predetermined value, the fuser thermal cutout is activated to effectively disconnect the heater
lamp from power.
14
8
2
13
10
16
11
15
12
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
Fuser bushes
Press springs
Press spring holders
Fuser lever L (R)
Exit sensor
Actuator (exit sensor)
Fuser guide
Fuser guide pulley
2-1-11
2H4
Fuser unit
Power
source PWB
Fuser thermal cutout
L
N
Fuser
heater
lamp
YC102-1
YC102-3
High
voltage
PWB
YC103-6
YC103-7
YC103-8
Control PWB
HEATN
SLEEP
ZCROSS
YC337-5
YC337-6
YC337-3
Fuser
thermistor
THERM
2-1-12
YC337-16
2H4
2-1-8
The paper exit section transports the paper which passed the fuser unit towards the top tray. The paper which passed
through the fuser unit turns on the actuator (exit sensor) in the fuser unit, and is led by the guide comprised of the rear
cover, frame and the FD cover guide, finally reaching the FD roller. The paper is delivered to the top tray by the rotation of
the FD roller.
2
1
4
10
Exit roller
Fuser exit pulley
Middle pulley
Rear cover
FD roller
Exit pulley
FD cover
Top tray
Exit sensor
Actuator (exit sensor)
2-1-13
2H4
Fuser unit
Control PWB
EXITN
YC333-3
Exit sensor
2-1-14
2H4
2-1-9
Duplex/conveying section
The duplex/conveying section consists of conveying path which sends the paper sent from the paper exit section to the
paper feed/conveying section when duplex printing.
10
8
9
7
3
5
DU cover B
DU holder
Middle pulley B
DU roller
DU cover A
Lower base cover
Feed roller
Feed pulley
Exit sensor
Actuator (exit sensor)
DUDR1
Duplex solenoid
DUDR2
YC343-1
YC343-3
Fuser unit
Control PWB
EXITN
YC333-3
Exit sensor
2-1-15
2H4
2-1-16
2H4
2-2 Electrical Parts Layout
2-2-1
(1) PWBs
l
4
1
5
6
8
7
Machine left
Machine inside
Machine right
2.
3.
4.
5.
6.
7.
8.
Control PWB ................................................ Main controller: Controls the software such as the print data processing
and provides the interface with computers.
Engine: Controls printer hardware such as high voltage/bias output control, paper conveying system control, and fuser temperature control, etc.
Power source PWB...................................... After full-wave rectification of AC power source input, switching for
converting to 24 V DC for output. Controls the fuser heater lamp.
High voltage PWB........................................ Generates main charging, developing bias, transfer bias and separation
charger bias.
Operation panel PWB .................................. Consists the LCD, LED indicators and key switches.
APC PWB .................................................... Generates and controls the laser beam.
PD PWB....................................................... Controls horizontal synchronizing timing of laser beam.
Zener PWB .................................................. Adjusts the drum surface potential.
Eraser lamp PWB ........................................ Eliminates the residual electrostatic charge on the drum.
2-2-1
2H4
(2) Switches and sensors
10
9
8
5
7
3
2
1
Machine left
Machine inside
Machine right
2-2-2
2H4
(3) Other electrical components
8
3
2
4
9
10
7
5
Machine left
Machine inside
Machine right
Main motor ........................................................ Drives the paper feed/conveying section and fuser unit.
Polygon motor................................................... Drives the polygon mirror.
Right cooling fan motor ..................................... Cools the interior of machine.
Left cooling fan motor ....................................... Cools the interior of machine.
Registration clutch ............................................ Controls the secondary paper feed.
Paper feed clutch .............................................. Controls the paper cassette paper feed.
Developing clutch.............................................. Controls the toner feed.
Duplex solenoid ................................................ Controls the paper conveying at the duplex conveying section.
MP paper feed solenoid .................................... Controls the MPF bottom plate of the MP tray.
Fuser heater lamp............................................. Heats the heat roller.
2-2-3
2H4
2-2-4
2H4
2-3 Operation of the PWBs
2-3-1
+24V1
FAN
ZCROSS
Zero cross
signal circuit
Power switch
SLEEP
AC input
Switching
regulator
circuit
+24V1
+24V2
Fuser heater
lamp control
circuit
Interlock
switch
HEATN
+3.3V2
THERM
Fuser unit
Fuser thermistor
Fuser
heater lamp
Fuser thermal cutout
2-3-1
2H4
YC104
YC105
YC102
YC103
YC101
Connector
YC101
Connected
to the AC
inlet
Pin
1
Signal
LIVE
I/O
I
NEUTRAL
YC102
Connected
to the fuser
heater lamp
HEATER COM
2
3
N.C.
HEATER LIVE
YC103
Connected
to the high
voltage
PWB
1
2
3
4
5
6
7
8
9
10
11
12
1
2
+24V1
SGND
FAN
THERM
+3.3V2
HEATN
SLEEP
ZCROSS
+24V2
+24V2
PGND
PGND
+24V1
FAN
1
2
+3.3V2
THERM
YC104
Connected
to the left
cooling fan
motor
YC105
Connected
to the fuser
thermistor
2-3-2
Voltage
120 V AC
220 - 240 V AC
Description
AC power input
O
I
O
I
I
I
O
O
O
O
O
120 V AC
220 - 240 V AC
120 V AC
220 - 240 V AC
120 V AC
220 - 240 V AC
24 V DC
0/24 V DC
Analog
3.3 V DC
0/3.3 V DC
0/3.3 V DC
0/3.3 V DC (pulse)
24 V DC
24 V DC
24 V DC
0/24 V DC
AC power input
24 V DC power source
Ground
Left cooling fan motor: On/Off
Fuser thermistor detection voltage
3.3 V DC power source
Fuser heater lamp: On/Off
Sleep mode signal: On/Off
Zero cross signal
24 V DC power source (via interlock switch)
24 V DC power source (via interlock switch)
Ground
Ground
24 V DC power source
Left cooling fan motor: On/Off
O
I
3.3 V DC
Analog
2H4
2-3-2
Control PWB
Control PWB
Engine
Main controller
Laser scanner
unit I/F
USB I/F
(Device)
Duplex solenoid
USB I/F
(Host)
Registration clutch
MP paper feed
solenoid
Operation
panel PWB I/F
+3.3 V
Developing clutch
MP paper feed
sensor
KUIO I/F
Main motor
Optional
paper feeder I/F
EEPROM
Optional expanded
memory (DIMM)
Exit sensor
Toner sensor
Eraser lamp
Right/Left cooling
fan motors
High voltage PWB
2-3-3
2-3-4
18
6
19
YC344
14
1
2
3
YC1
12
YC2
YC338
YC9
25
50
7
YC7
1
143
1
144
2
1
26
1 1
3
YC342
YC343
YC3
12 YC6 9
YC332
A1
A2
B1
B2
2
3
23
YC11
YC301
YC334
YC335
5
1
1
6
22
1
YC330 3 YC3401 YC341
3
1
1
2
1
YC331
24
1
5
YC337 1
YC339
YC4
A29
A30
B29
B30
2H4
3
1
YS1
U300
YC8
1
5 YC333
1
3
2H4
Connector
YC4
Connected
to the operation panel
PWB
YC7
Connected
to the operation panel
PWB
YC9
Connected
to the laser
scanner unit
YC330
Connected
to the MP
paper sensor
YC331
Connected
to the main
motor
YC332
Connected
to the paper
sensor
YC333
Connected
to the exit
sensor
YC334
Connected
to the registration
clutch,
paper feed
clutch and
developing
clutch
Pin
1
Signal
VBUS
I/O
O
Voltage
5 V DC
Description
5 V DC power source
2
3
HUSBDN
HUSBDP
I/O
I/O
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
+5V
+3.3V1
FPDAT
FPDIR
FPCLK
SGND
FPRSTN
O
O
O
O
O
O
5 V DC
3.3 V DC
0/3.3 V DC (pulse)
3.3/0 V DC
0/3.3 V DC (pulse)
3.3/0 V DC
5 V DC power source
3.3 V DC power source
Operation panel PWB data signal
Operation panel PWB communication direct signal
Operation panel PWB clock signal
Ground
Operation panel PWB reset signal
+24V3
PGND
PLGDRN
PLGRDY
PLGCLK
PDN
SGND
VDON
VDOP
OUTPEN
SAMPLEN
+3.3V2
+3.3V2
SGND
HANDSN
O
O
I
O
I
O
O
O
O
O
O
I
24 V DC
0/3.3 V DC
0/3.3 V DC
0/3.3 V DC (pulse)
0/3.3 V DC (pulse)
0/3.3 V DC (pulse)
0/3.3 V DC (pulse)
0/3.3 V DC
0/3.3 V DC
3.3 V DC
3.3 V DC
0/3.3 V DC
24 V DC power source
Ground
Polygon motor: On/Off
Polygon motor ready signal
Polygon motor clock signal
Horizontal synchronizing signal
Ground
Video data signal (+)
Video data signal (-)
Laser output enable signal
Sample/hold timing switching signal
3.3 V DC power source
3.3 V DC power source
Ground
MP paper sensor: On/Off
1
2
3
4
5
1
2
3
+24V3
PGND
MMOTRDYN
MMOTCLK
REMOTEN
+3.3V2
SGND
PAPER
O
I
O
O
O
I
24 V DC
0/3.3 V DC
0/3.3 V DC (pulse)
0/3.3 V DC
3.3 V DC
0/3.3 V DC
24 V DC power source
Ground
Main motor ready signal
Main motor clock signal
Main motor: On/Off
3.3 V DC power source
Ground
Paper sensor: On/Off
1
2
3
+3.3V2
SGND
EXITN
O
I
3.3 V DC
0/3.3 V DC
+24V3
24 V DC
24 V DC power source
2
3
REGDRN
+24V3
O
O
0/24 V DC
24 V DC
4
5
6
FEDDRN
+24V3
DLPDRN
O
O
O
0/24 V DC
24 V DC
0/24 V DC
2-3-5
2H4
Connector
YC335
Connected
to the MP
paper feed
solenoid
Pin
1
2
Signal
+24V3
MPFDRN
I/O
O
O
Voltage
24 V DC
0/24 V DC
YC337
Connected
to the high
voltage
PWB
1
2
3
+24V1
+3.3V2
ZCROSS
I
O
I
24 V DC
24 V DC power source
3.3 V DC
3.3 V DC power source
0/3.3 V DC (pulse) Zero cross signal
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
1
2
3
4
FAN
HEATN
SLEEP
MHVDR
RTHVDR
PSEL1
HVCLK
REGN
TCNT
O
O
O
O
O
O
O
I
O
0/24 V DC
0/3.3 V DC
0/3.3 V DC
0/3.3 V DC
0/3.3 V DC
0/3.3 V DC
0/3.3 V DC (pulse)
0/3.3 V DC
PWM
MCNT
THVDR
CASE
THERM
+24V3
SGND
+24V2
+24V2
PGND
PGND
O
O
I
I
O
I
I
-
PWM
0/3.3 V DC
Analog
Analog
24 V DC
24 V DC
24 V DC
-
YC340
Connected
to the toner
sensor
1
2
3
+3.3V2
TEMPTY
SGND
O
I
-
3.3 V DC
0/3.3 V DC
-
YC341
Connected
to the right
cooling fan
motor
1
2
+24V1
FAN
O
O
24 V DC
0/24 V DC
24 V DC power source
Right cooling fan motor: On/Off
YC342
Connected
to the eraser
lamp
1
2
ERASER
ERASRW
O
O
0/24 V DC
24 V DC
YC343
Connected
to the
duplex solenoid
1
2
3
DUDR1
COMMON
DUDR2
O
O
O
0/24 V DC
24 V DC
0/24 V DC
YC339
Connected
to the high
voltage
PWB
2-3-6
Description
24 V DC power source
MP paper feed solenoid: On/Off
2H4
Connector
YC344
Connected
to the
optional
paper feeder
1
Pin
1
2
3
4
5
6
Signal
+24V3
PGND
PFSI
PFSO
PFSEL
+3.3V1
I/O
O
I
O
O
O
Voltage
24 V DC
0/3.3 V DC (pulse)
0/3.3 V DC (pulse)
0/3.3 V DC
3.3 V DC
Description
24 V DC power source
Ground
Serial communication data input signal
Serial communication data output signal
Paper feeder selection signal
3.3 V DC power source
2-3-7
2H4
2-3-8
AC
input
YC-B
YC201
Cassette
switch
Registration
sensor
Fuse
YC203
YC202
YC-T
YC105
1
2
3
4
5
1
2
3
4
5
1
2
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Transfer roller
Paper
sensor
Left cooling
fan motor
+24V2
+24V2
PGND
PGND
HVSEL
1
2
3
4
5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
YC335
1
2
3
4
5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
PAPER
GND
+3.3V2
YC333
YC339
YC337
YC332
Exit sensor
MP paper
feed solenoid
+24V1
+3.3V2
ZCROSS
FAN
HEATN
SLEEP
MHVDR
RTHVDR
PSEL1
HVCLK
REGN
TCNT
MCNT
THVDR
CASE
THERM
+24V3
SGND
Fuser thermistor
1
2
YC104
YC102
+24V1
Interlock
switch
YC101
SW1
+24V2
YC103
L L
N N
YC-M
Zener PWB
+3.3V2
Power
switch
Developing roller
Drum
1
2
3
4
5
6
7
8
9
10
11
12
+24V1 1
SGND 2
FAN 3
THERM 4
+3.3V2 5
HEATN 6
SLEEP 7
ZCROSS 8
+24V2 9
+24V2 10
PGND 11
PGND 12
THERM
1
2
1
2
+24V3
MPFDRN
FAN
+24V1
1
2
3
1
2
3
3
2
1
3
2
1
1 EXITN
2 SGND
+3.3V2
3
1
2
3
Registration
clutch
Paper feed
clutch
+24V3
+3.3V2
YC341
YC301
+3.3V1
Right
cooling
fan motor
Developing
clutch
+24V1
YC331
Control PWB
YC334
24 V DC power off
at sleep mode
+24V2
+24V3
2 2
REGDRN 1 1
1
2
1
2
1
2
3
4
+3.3V2
RFCLK
RFDATA
SGND
4
3
2
1
4
3
2
1
+24V1
FAN
+24V3 2 2
FEDDRN 1 1
1
2
3
4
5
6
1
2
3
4
5
CN1
Main motor
Duplex
solenoid
YC1 YC2
YC343
YS1
YC340
Toner
sensor
YC344
+3.3V1
YC330
1
2
3
1
2
3
4
5
6
7
8
ERASER
ERASRW
1
2
1
2
+24V3
PGND
PLGDRN
PLGRDY
PLGCLK
PDN
SGND
VDON
VDOP
OUTPEN
SAMPLEN
+3.3V2
Parallel I/F
Network I/F
1
2
3
4
5
6
7
8
9
10
11
12
22
14
HUSBDP
HUSBDN
VBUS
FPRSTN
GND
FPCLK
FPDIR
FPDAT
+3.3V1
+5V
USB I/F
3
2
1
3
2
1
1
7
6
5
4
3
2
1
MP paper
sensor
7
6
5
4
3
2
1
1
2
3
1
2
3
4
5
6
YC9
7
8
9
10
11
12
YC11
YC6
YC3
YC4
YC7
HANDSN
GND
+3.3V2
YC338
DC-DC converter
+5V
1
2
3
1
2
3
4
5
6
1
2
3
4
+24V3
2 2
DLPDRN 1 1
1
2
3
1
2
3
+3.3V2
TEMPTY
SGND
1
2
3
4
5
+24V3
PGND
MMOTRDYN
MOTCLK
REMOTEN
1
2
3
4
5
1
2
3
4
5
DUDR1
1
COMMON
2
3 DUDR2
1
2
3
KUIO-LV
Expanded DIMM slot
3
2
1
3
2
1
1
2
3
4
5
6
1
2
3
4
5
6
+24V3
PGND
PFSI
PFSO
PFSEL
+3.3V1
1
2
1
2
8
9
10
1
2
3
4
5
6
7
7
6
5
4
3
2
1
5
4
3
2
1
7
6
5
4
3
2
1
YC3
PDN
SGND
NC
+3.3V1
2
1
3
4
1
USB I/F
YC1
PD PWB
YC2
Polygon motor
4
3
2
1
APC PWB
YC1
5
4
3
2
1
3
2
1
10
9
8
7
6
5
4
YC1
1
2
3
4
5
6
7
8
9
10
2-4-1
1
2
3
4
5
6
7
8
9
10
2-4 Appendixes
1 1
2 2
3 3
2H4
Appendixes
2-4-1
2H4
(2) Repetitive defects gauge
2-4-2