eo)
4344 Series
Hermetically Sealed Thermostat
+ Snap-action switching
pid thermal response
+ Single pole, single throw
+ Normally open or normally closed
+ Pre-set, non-adjustable calibration
+ Various mounting configurations available
+ UL recognized, fle #34618, see page 36 for details
+ CSA recognized, fle #LR24458, see page 36 for details
Description
‘The Klixon 4844 precision therm-
stat is constructed with a snap-
acting bi-metal dise which serves
as the actuating element, As the
temperature reaches a predeter-
‘mined calibration point, the dise
snaps to its reverse curvature
producing the crisp, postive
switching action inherent to
Kilixon thermostats. This feature
assures reliable, consistent
operating temperature over long.
‘eyele life. The standard thermo-
stat is copper-nickel plated with
silver contacts. Other plating
finishes are available upon
request. Gold plated contacts can
be furnished for the electrical
loads listed in the following table
to assure reliable circuit switch-
ing under low wattage conditions.
Gold plated contacts are not
suitable for higher loads.
Gold Contact Ratings
(Resistive)
{so vacioc [500 ma and below
115VAC | 200 mA and below
za0 VAC | 100 mAand below
ur most common mounting con-
figurations are depicted. Many
other varieties are available.
Leads can be welded to pin type
terminals to form an integral unit.
‘The switch can be custom pack-
‘aged into a probe, strap mount, or
immersion thermostat. Consult
the factory for special requests.
Switching Action
All thermostats are supplied with
single pole, single throw switch-
ing. The contacts ean be eon-
structed as:
Normally closed - limit type
application; contacts open on
temperature rise at a pre-
determined temperature to de-
energize the circuit. Contacts
automatically re-close as the
device cools to a pre-determined
temperature.
Normally open - fan type
application; contacts close on
temperature rise at a pre-
determined temperature to
energize the cireuit. Contacts
automatically re-open as the
device cools to a pre-determined
temperature,
‘The opening and closing temper-
atures are pre-set and non-
adjustable.
Typical Cross Section View
When neato, the intemal strosses of
the bimetal cause thedscto reverse
its ourvaure wih a snap-acton ata
fixed, preset temperature andonerate
the electrical contacts
‘Adocrease inthe ambient tempera
ture below te reset temperature of
thedisc relieve ho ntoral stresses
In the dso, The dis returns to ts
formal curvature and the contacts
‘assume their normal operating
positonPerformance Characteristics Temperature (Use table below for common operating temperatures).
Switch Action “Ambient Temperature Range:
SPST (snap-action) -80°F to +550°F, (-62.2°C to 287.8°C)
Contact Resistance Maximum ambient exposure while in the closed contact position is 200°F
0.050 ohms maximum above contact closing temperature
per MIL-STD-202, Method 307 Operating temperature
Contact Ratings (Resistive) ‘Temperature at which normally closed contacts open or normally open
sevice ASMCTROACT Ui) contact ce
‘Amperes cycles
=O] 25 [10 100000) Tolerance
55 30 15° | 50, 000 ) Allowable range above and below setpoint and reset temperatures.
so | «0 | 20 | 25000]
ss | 50 | 25 | 10000) Differential
10 | 60 | 30 | 5000) Subtract the differential from the operating temperature to determine the
Sed tac arent temperature at which the contacts will etum to the normal position
— (reset temperature).
1250 VAC, rms,
60 Cycles for 1 minute, ena | Diferentit | Tolerance operating | Diterentt | Tolerance’
anys perature rempeatre| |
per MIL-STD-202, Method 301 iia eC eee eee es * [ec |r [¢ [a [ac
-e | sa] 0 [is7| 10 7g,)a89 | 30 [v7] 8 | aa
Vibration Resistance -40 |-400] 30 | 167] 10 ze0'}iot4] 30 |167| 8 | a4
5-2000 He, 206, 16 |-261| 0 [167] 10 200 |r100] 30 |167/ 8 | 44
per MIL-STD-202, Method 204, Lo |-azal 2 |i] 5 240 [11561 30 |167| 9 | 44
wo [2p [tir] 5 20 fiers] 30 [167] 8 | 44
on D, (anmonitared
ee ’ 2 167) 20} 141) 5 260 1267] 30 | 167] 8 | 44
po gw far} a faal 5 zm jso2| 30 | 157| 6 | 44
2006, 6 milisesnds {wep api] ao as PET] eae
per MIL-STD-202, Method 213 eo fise| 2 [as] 5 soo |rwsa| 20 |167| 9 | 44
ro faa| a [ara] 5 sno |isaa| 40 [222] 2 | 67
Hermeticity wo |2s7| 2 [a] 5 seo |isoo| «0 | 222] 2 | 67
1X 10° atm co/see. max, go [322] 20 [a] 5 930 |165.6] 40 | 222] 12 | 67
per MIL-STD-202, Method 112, oo |578| 20 |1ta| 5 eo firs] 40 | 222] 2 | 67
Condition C no |43] 20 faa] 5 azo |i767| 40 | 222] 12 | 67
solo] 20 {isl 5 a7 |ivos| 40 | 2221 12 | 67
Salt Spray Figo Psee yao Pants 00 fool 40" [222] 12 | 67
per MIL-STD-202, Method 101, | 140 |600] 20 | 1111 5 425 farea| 40 |222| 12 | 67
epee 160 | 58] 20 |nia] 5 460 [2z2a| 40 |222| 12 | 67
ico |711| 0 [oi] 5 a7 [ouss| 70 | 69 | 25 | 199
Weight imo [77] 2 frit] 500 Jeen.0] 70] 389] 25 [199
Peaeanit Asgrams | 100 [022] 20 | rts | 5 525 [araa| 70 | 269] 25 | 199
aur . ” 59 | 199 78] 20/114) 5 550 |2e78| 70 | 389) 25 | 139
with bracket 59 rams | op [eva | 20 [111 | &
Consul factory if desired operating temperature does not appear inthe table.
erin + an adtinal 23°F tolerance is equied fr overmoled vices
#720 VA, 110-600 VAG, break but
not make, ungrounded cup Qualifications
'360 VA, 600 VAC, make and ULICSA recognition
break ungrounded cup see page 36 for details
125 VA Pilot Duty,24-240 vac, Plating
Copper-nickel
make and break, grounded or
ungrounded cup
“Atti rating, slab asa controtccut
{temperature iin doce fr hazartious
locaton motors and generators.
(other finishes available upon request)Common Mounting Configurations
Terminal Dimensions
4344632
Ore.
‘ine be maximo torque
oi fron |
4344-176"
Bow Coping #152 oF gu,
face
i
v
% | sera
M52 F sim amber expose)
hn addtional 2°F tolerance is required for overmolded devices.
‘Standard Lead Connections
Leads ar avalale neat esis rubber neoprene, sooner and Teton" n #18 gaug sanded
Wie in strc incerant eng of 41 36"
Other gauges and lengths avaiable upon request.
“Tademark of 1 Dupont de Nemows and Ca
Line terminal is marked for
grounded AC line voltage
applications.
Dimensions are in inches.