ME 360 - Spring 2015 Test #2A
Closed book, closed notes. ‘Name?
A 3/30/15
‘Test rules: individual work only, calculators allowed, scratch paper allowed, closed-book, closed notes, 55
minutes for test time.
1. [15 pts] A first-order RC filter cirouit is shown 47K
{tothe right. Note thatthe overall capacitance is
composed of fwo capacitors in parallel, one of
e+ le whose capacitance is unknown,
feseee™ 2 4) Select a capacitor from the table below Youn —— Four
such that the time constant of the system is 0.4 0nF |-
closest to 1.5 milliseconds, JUSTIFY your
hoice of cs ite SHOW your work. >
eno apactiance. SIZE your wo The = Hane (aleoteC)= 1 Sete
.0022nF | F 0.01 uF 220F J
0.001nF | 0.0022nF | 0.00471 uP | 0,022, loc: L seis? ‘
se OIE
0.047uF | OnE [onir\ o47uF | 1.0uF Anes?
= tiger We rr pe )
b) Sketch the output waveform response on the diagram provided below for the step input shown.
Input step
x
>
Wel 4 $
Gop. @ 3 8 =~
3
7 aby= SA%
2 > Ave)
3 = ABUT
g J R16 Ie
> err fr
Horizontal sensitivity: 500 usec/div Sit
12S sec 2sv0 (o.w2)~ 140
L sme = FAive Beed - tS Lo ze
“ —— <2 Bt:
(Ce 7 FEE se BYE
ot a:
as (I-02) = (mY
OF ya Ga-yo)oure
Sear (ede owe2. [5 pts] A “device under test (DUT)" on a shaker table is driven with an amplitude of 5 g's of
vibration at 20 Hz. What is the corresponding displacement amplitude, in mm? SHOW your work.
Byes Seine = agOseket REE rok a Mec
= 125.46 Gee
alg = LOS So Cirs.06 t) we
UM = NA Coe (125.66 Y et oe
> Tae os Ager
- = bm
Bs 108 ca (rsecl > [al- TO = 51 d07 m= F
Crs y
3. [HO pts] ASpring-mass system has a mass m= 3.25kgand a spring stiffness of k =3250%,
m
Determine the natural frequency of the system and sketch a portion of the free response on the plot
below. Assume any desired amplitude and very low damping.
' Rm THe,
0.00 005 019 045 070 025 050 098 a4 045 050 = =S\ TTR Yrgec
Time, see
= Ndi
Wa
skens S
arent4. [10 points}
Part A: You are to mount a pair of strain gages on the axially loaded beam shown in the figure below.
Using the illustrated beam on the left side of the figure, indicate the locations of the two gages for
this case.
Part B: Show how you would place the two gages in the Wheatstone bridge shown above. Place the
‘gages in the correct locations and completely label the figure, indicating the state (tension or
compression) of each gage.
5. [10 pts]
Part A: You are to mount a pair of strain gages on a beam loaded in bending as shown in the figure
below. Using the illustrated beam on the left side of the figure, indicate the locations of the two gages
for this case. Note the transverse direction of the load.
Part B: Show how you would place the two gages in the Wheatstone bridge shown above. Place the
gages in the correct locations and completely label the figure, indicating the state (tension or
compression) of each gage.G=PA
6. [20 pts] Two strain gages are mounted to a hollow square tube as shown in the figure below. The
tube is loaded in axial tension. A cross-section of the square tube is also shown in the figure.
Use the numerical values given below to find the stress, the strain, and the voltage output, Vous, from
the Wheatstone bridge for this case. The distance between the gages and the end of the beam is
indicated by L.
E =30x10° Ibffin? =L=20% inch Wo=0.750 inch Vin= 10.6 volts F212
0.460 inch P =5260Ibf R= 350 ohms:
ZZ a4 ew, .
luit-b,
AJ tw, = @e-0 =
ho
P cross-section ; a
of square tube = O.3S07«
_ TUG HSE go Ss
"Base in {tte war >
et
[4190 WA 6 yt mA (BROS rns
Zao Boh fa Oe eee Ae
Ver i
oR. Lreesl Suse pres
Cav) (os #6 3)( 10.6)
A
z
= Sat x 7
f satel )
ser ingas
- Sten, In
Hr Re 1M I ig ew
2 dee Wa Jose 2
1e35 PY Vee e 2h log t he,
7. [30 pts] A DC permanent magnet motor develops 45.2 in-Tbf of torque When operated at an armature
voltage of Vs=60 volts and a speed of 1035 RPM. The manufacturer claims that the motor has a stall
torque of 8.0 N-m when operated at an armature voltage of Vs=60 volts.
‘Showing all work, determine:
a, The motor's theoretical "no-load" speed, wnt, oNnt=_ Sod eS Gee
b. ‘The motor’s theoretical back-EMF constant, ks, ker 01467 Vr se7“ped
c. The motor’s theoretical torque constant, ka, ke_O.\16t YA
d. The motor’s theoretical resistance, Rs, and Ra=__ tPF Se
e. The motor’s efficiency at 1035 RPM when operated at an armature voliage of V.=60 volts.
ne BSS %
10 | ~ ——
9
BK
:
E
z
gs
ke
2 el
1
9 |
oO 50 100 150 200 250 300 350 400
Speed, radisec Cone® 305 reMbee
& A O_o
soll QU = 40.64 > ky &Y opus
wi te? ole + Fes | res
Te Ye = Lats a sks ON
(
logs ory rae = (ae 380M a
an 10 580 frm (oF.3 v4
z > Pats TISPN A t
Vex bso Co -o.mcr 10818) pe eps SENT
LAS Pas renrheows 1572 EW
= web = SSI yyer 3IS%
tas = 6 1ME Non rb.vt A= si san~ BOY Oy