Test Databank Print
D:\TestGen\CSWIP 2006 Questions Set 10 .mdb
What is the annealing temperature of plain carbon steel less that 0.2% carbon
content?
A. 900c to 1100¢
B. 850c to 950
C, 600c to 750c
D. 400c to 550¢
E.
Correct Answer: B
Reference:
Media Type:
Media Location:
Question ID: 10
The solution annealing of some metallic alloys may require?
‘A. Slow cooling
B. Slow cooling at room temperature
C. Rapid cooling with frozen carbon dioxide
D. Rapid cooling rate
E.
Correct Answer: D
Reference:
Media Typ
Media Location:
Question 1D: 20
In sub critical annealing the steel is heated to what temperature below the lower
critical temperature?
A. 723¢
B. 800c
C. 850¢
D. 900c
E.
Correct Answer: A
Reference:
Media Typ
Media Location:
Question ID: 30Page
The term annealing generally means to bring the metal, or alloy to its?
A. Hardest and ductile natural condition
B. Softest and most ductile natural condition
C. Hardest and tempered condition
D. Softest and quenched condition
E.
Correct Answer: B
Reference:
Media Type:
Media Location:
Question 1D: 40
In normalizing the steel is removed from the furnace and?
A. Allowed to cool in still air
B. Controlled cooling in the oven
C. Allowed to cool rapidly in cooled air
D. To achieve normalizing we should quench the steel after removing it from the
oven
gE.
Correct Answer: A
Reference:
Media Type:
Media Location:
Question ID: 50
When we normalize stee! what will be the affect on the stee!?
A. Softness and ductility will increase
B. Softness and ductility will decrease
C. Softness will not be affected when we normalize steel
D. This will add more carbon content to steel
ae
Correct Answer: B
Reference:
Media Type:
Media Location:
Question ID: 607 When we normalize steel! what will be the affect on the steel?
‘A. Toughness and impact strength will improve
B. Toughness and impact will be give the metal less strength
C. Toughness will improve
D. Impact values will improve
E,
Correct Answer: A
Reference:
Media Type:
Media Location:
Question 1D: 70
8 When we normalize stee! what will be the affect on the steel?
A. Strength and hardness are decreased
B. Strength and hardness are increased
C. Normalizing steel will have no affect on hardness
D. Normalizing steel will have no affect on strength
E
Correct Answer: B
Reference:
Media Type:
Media Location:
Question ID: 80
9 For plain carbon steel ,the steel must have a sufficiently high carbon content to be
hardened by thermal treatment which is generally considered as?
‘A. More than 0.3%
B. More than 0.1%
C. More than 0.01%
D. More than 0.2%
7
Correct Answer: A
Reference:
Media Type:
Media Location:
Question 1D: 90
Page10 Which is considered the quickest cooling media?
A. Water
B. Oil
C. Brine
D. All are equal when cooling
E.
Correct Answer: c
Reference:
Media Type:
Media Location:
Question ID: 100
11 Tempering is a sub critical heat treatment process that used only after?
A. Normalizing
B. Annealing
C. Hardening
D. Softening
E.
Correct Answer: c
Reference:
Media Type
Media Location:
Question ID: 110
12 When carrying out tempering to steel ,we do which of the following?
A. Re-balance the steel
B. Un-balance the steel
C. Tempering will have little affect on the steel
D. None of the above
E.
Correct Answer: A
Reference:
Media Type:
Media Location:
Question ID: 120
Page 413 The process of tempering starts at around what temperature?
A. 2206
B. 150C
c. 2006
D. 100¢
E.
Correct Answer: A
Reference:
Media Type:
Media Location:
Question ID: 130
14 Tempering will increase the level of ?
A. Hardness
B. Toughness
C. Carbon content
D. All of the above
E.
Correct Answer: B
Reference:
Media Type
Media Location:
Question 1D: 140
15 The purpose of stress relieving is to ?
A. Relieve external elastic stress
B. Relieve internal elastic stress
C. To give the material extra hardness
D. To give the material extra toughness
E.
Correct Answer: B
Reference:
Media Type:
Media Location:
Question ID: 15016 Which types of steel sometimes require special heating curves?
A. Stainless steels
B. Copper alloy steels
C. Austenitic steels
D. Creep resistant steels
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 160
17 When a steel will not return to it original dimensions due to yield this is expressed
as?
A. Plastically deformed
B. Elastically deformed
C. Normally deformed
D. All of the above
E
Correct Answer: A
Reference:
Media Type:
Media Location:
Question ID: 170
18 When we heat steel the higher the temperature will produce?
A. Less elastic strain
B, More elastic strain
C. The heat will have no effect on elasticity
D. Elastic strain is never converted into plastic strain
E.
Correct Answer: B
Reference:
Media Type:
Media Location:
Question 1D: 180
619 We use pre-heating to achieve which of the following?
A. To control the structure of the weld metal in the HAZ on cooling
B. To improve diffusion of gas molecules through an atomic structure
C. To control the effects of expansion and contraction
D. All of the above
E.
Correct Answer: D
Reference:
Media Type:
Media Location:
Question ID: 190
20 Martensite is produced by the entrapment of a carbon solution at which
temperatures?
A. Below 300C
B. Above 350C
C. Above 400C
D. Above 500C
E.
Correct Answer: A
Reference:
Media Type:
Media Location:
Question 1D: 200
Page