SEARS—__
CRAFTSMAN.
2 6677
DRILL GRINDING ATTACHMENT
Fig.
FEED NUT
Locynur
FEED
Ss
PIVOT PIN apuUSTABLE
SUIDE BRACKET
BOLT, WASHER AND
WING NUT (Not
Inelodes)
SLOTTED BASE
‘TENSION SCREW
POINT ANGLE/DRILL OVERHANG CHART
88° | 1/16 Inch Thin Sheets :
ea
68° | 50% of Drill Dia. Very Hard Materials
59° | 50% of Dri Dia, | General Purpose Drilling
‘49° | 100% of Drill Dia.| Soft Materials (ie. Copper, Wood, Plastic)
41°/ As Required | Countersinks: Wood, Hard Rubber, Fibre etc.
INSTRUCTIONS FOR:
DRILL GRINDING ATTACHMENT
96677
Your New General Drill Grinding Grinding Attachment, use only
Attachment has been carefully —_U.L., A.N.S.L., OSHA’ approved
designed and constructed from grinding machines and wheels.
the finest materials andthe latest Please read and observe the
manufacturing techniques. To ob- following instructions and safety
tainthe best results from your Drill__ precautions.
‘MOUNTING INSTRUCTIONS TROUGH
This Drill Grinding Attachment er
‘and your grinder should be fast- NY
‘ened firmly toa sturdy bench as in ~)
Fig. 1, A 48 inch hole for 2 tolt YK
should be drilled in the bench f
about 2% Inches from the front of DIVENSION FROM Fig.2
the atinding wheel. Fasten the at OVERHANG CHART
tachment to the bench using @
bolt, washer and wingnut (not in- chart for each point angle setting
cluded). Use of tool in side gring- Adjust ip rest until it extends
ing should only be done with a lightly into the flute of the dil as
wheel specifically designed for Shown in Fig. 2. Move rear bracket
side grinding and approved by
‘ANSI, OSHA
SAFETY PRECAUTIONS Fos
+ Securely fasten Dill Grinding At-
‘tachment to workbench,
UP
‘+ Wear OSHA and A.N.S.I. approv REST
2d eye protection (goggies, face
Shield) when operating this tool.
* Follow grinder manufacturer's to support back of drill n this posi-
safety recommendations, tion Tighten clamp keeping dil
flute against lip rest (Fig.
‘* Make sure all guards are in place Gonerate Drill ‘Sancing” ee
over grinaing wheel. ment automatically sets the clear-
* For side grinding, use wheel spe-__ance angie of the drill point.
cifically engineered for that
purpose.
2. With the grinder of, oosen nut
slightly and move siotted base
QRERATING INSTRUCTIONS — {ha"ri ust graes the. wheal
1. Using the pointangiearil over. (Re, ll ust grazes the whee!
hang char, choose the best point
ia ‘ammarerial ts tachment back and forth past the
ngle for the material tobe drilled. grinding wheel. If pivot is t00 free
2. Place the drill in trough. The or ‘too stiff, adjust the tension
amount that the drill point should screw slightly until the attach-
‘overhang lip rest is indicated in ment swings smoothly.4, To sharpen the first lip of drill,
turn on grinder and with slow,
short sweeps grind the drill, Ad-
vance drill gradually by using the
feed screw until the entire surface
Is ground. The clamp should be
loosened slightly while feeding
the drill forward, then reclamped
to prevent movement of the bit.
5, Turn off grinder. Do not remove
rill or change adjustment.
6. To grind the second lip of the
dill, turn attachment away from
the grinding wheel, loosen clamp
only. Rotate drill until the opposite
flute rests against the lip rest. Re-
tighten clamp,
7. Tur on gtinder and with slow,
short sweeps, grind the second
face of the drill. This method en:
sures that the two cutting edges
are the same length,
8 TURN OFF GRINDER and re-
‘move drill from the attachment.
HELPFUL HINTS
Feed drill by small amounts,
When sharpening broken dlls,
much time may be saved by
roughly shaping drills tree hand
before using attachment. Dip drill
inwater when shaping freehand to
prevent overheating (blue
appearance).
Certain drills may sharpen with
heel behind the cutting edges,
(Fig. 4). Carefully remove this hee!
free hand so that the drill will cut
freely.
menopER HEEL
Frequent sharpening makes drill
ing easier and gives better life to
your drils.
For a drill to cut easily and to siz
oth cutting edges must be the
‘same length and have the same
point angle. Also there should be a
definite clearance angle (Fig.
ee
wen Yan
RM Lf 7 _yieie
i
10
Fig.
Sold by SEARS, ROEBUCK AND CO,, Chicago, 0604 USA. PRINTED IN USA
SEARS:
CRAFTSMAN. aaa
DRILL GRINDING
ATTACHMENT
MOUNTING AND USE INSTRUCTIONS