Professional Documents
Culture Documents
System Information Blocks (Sibs) in Lte
System Information Blocks (Sibs) in Lte
(SIBs) in LTE
Consists of MCC and MNC. The first listed one is the Primary PLMN
p-Max
Value applicable for the cell. If absent the UE applies the maximum power
according to the UE capability. If eNB configures the value more than the value
supported by the UE then UE will set the max value aupported by the UE
capability. Example UE Catagory 3 supports max 23 db
cellReservedForOperatorUse
trackingAreaCode
cellIdentity
cellBarred
intraFreqReselection
q_RxLevMin
q_RxLevMinOffset
SIB 1 (2)
freqBandIndicator
schedulingInfoList
si_Periodicity
Periodicity of the SI-message in radio frames (SI will be transmitted within the
specified radio frame)
sib_MappingInfo
carries the List of the SIBs mapped. SIB2 is always present in the first element of
schedulingInfoList
si_WindowLength
specifies that a SIB should be transmitted somewhere within the specified window
length. Value is in ms. This window starts at the starting sub-frame of the
mentioned si_periodicity. SIBs can be received in any of the sub-frame as
mentioned in the WindowLength.
systemInfoValueTag
radioResourceConfig
numberOfRA_Preambles
preamblesGroupAConfig_exist
powerRampingParameters
powerRampingStep
preambleInitialReceivedTargetPower
ra_SupervisionInfo
preambleTransMax
ra_ResponseWindowSize
mac_ContentionResolutionTimer
maxHARQ_Msg3Tx 4
SIB 2 (2)
bcch_Config
modificationPeriodCoeff
pcch_Config
defaultPagingCycle
Default paging cycle, used to derive T. Value rf32 corresponds to 32 radio frames
nB
is used as one of parameters to derive the Paging Frame and Paging Occasion
prach_Config
used to specify the PRACH configuration in the system information and in the
mobility control information
rootSequenceIndex
prach_ConfigIndex
mentions the:
Preamble format: 0-4 (For frame structure 1 preamble format is 0-3 and for frame
structure 2 it is 0-4)
SFN: whether it will be EVEN no. frmae OR any frame
subframe number: carrier the subframe no. within the SFN
(Look for the table in TS36.211 - Table 5.7.1-2)
highSpeedFlag
zeroCorrelationZoneConfig
SIB 2 (3)
pdsch_Config
pusch_Config
used to specify the common PUSCH configuration and the reference signal
configuration for PUSCH and PUCCH
pucch_Config
soundingRS_UL_Config
uplinkPowerControl
used to specify parameters for uplink power control in the system information
and in the dedicated signalling
ue_TimersAndConstants
Timer values
freqInfo
timeAlignmentTimerCommon
used to control how long the UE is considered uplink time aligned. Value in
subframes
SIB3 (2)
intraFreqCellReselectionIn
Cell re-selection information common for intra-frequency cells
fo
Minimum required RSRP for cell reselection. value -70 - 22 dbm, Actual
q_RxLevMin
value=signalled value*2
# used to trigger intrafreq. measurements
# specifies the Srxlev threshold (in dB) for intra-frequency measurements.
# If the field s-IntraSearchP is present, the UE applies the value of ss_IntraSearch
IntraSearchP instead. Otherwise if neither 09s-IntraSearch nor sIntraSearchP is present, the UE applies the (default) value of infinity for
SIntraSearchP.
is used to09 indicate whether all the neighbouring cells use 09Antenna Port
presenceAntennaPort1 1. When set to TRUE, the UE may assume that at least two cell-specific
antenna ports are used in all neighbouring cells.
used to provide the information related to MBSFN and TDD UL/DL
neighCellConfig
configuration of neighbour cells.
# specifies the cell reselection timer value
t_ReselectionEUTRA
# defines time to trigger for cell reselection
# The parameter can be set per E-UTRAN frequency
# max. allowed UL transmit power for intra-frequency neighbouring E-UTRA
p_Max
cells. If absent the UE applies the maximum power according to the UE
capability
q-OffsetCell
specifies the offset between the two cells. Value -24 - +24dB
csg_PhysCellIdRange
intraFreqNeighCellList List of intra-frequency neighbouring cells with specific cell re[1-16 instances]
selection parameters
threshX-Low
allowedMeasBandwidth
cellReselectionPriority
neighCellConfig
q-OffsetFreq
interFreqBlackCellList
followingARFCNs
ARFCN groups
cellReselectionPriority
absolute priority of the GERAN layer. Value 0 to 7, whereas 0 is the lowest priority
ncc_Permitted
q_RxLevMin
p_MaxGERAN
threshX_High
threshX_Low
# Threshold (in dB) used by UE for cell re-selection to a HIGHER priority frequency
# The Srxlev of the candiate cell is greater then threshX_High
# Value 0 to 31 dB. Actual value= Signaled value * 2
# Threshold (in dB) used by UE for cell re-selection to a LOWER priority frequency
# Cell re-selection is allowed only when Srxlev of the candiate cell is greater then
threshX_Low and RSRP of serving cell is less than the value of ThreshServingLow
singalled within SIB3
# Value 0 to 31 dB. Actual value= Signaled value * 2
hnb-Name
messageIdentifier
serialNumber
warningType
warningSecurityInfo
messageIdentifier
serialNumber
warningMessageSegmentType
[last/not last]
messageIdentifier
serialNumber
warningMessageSegmentType