ea TUTORIAL 4: TORSION
‘Question + Vie on T0P
1S kn oF come:
— 400
:
ie ett + |, [800
thre
ae:
4 rectangular cantilevered colum whlch 4:
fervice load of 5:ku, acting horizontally ae a
ty 85 indicated
rial
Determine the maxim” eccentricity at
der that reinforcement. should not be
lear stresses on the colum.
red” to be adequ
16 bars at top and botton.
Check the shear stresses and design
Supports; “Indicate where no torsi
jonal reinforcement required at tne
inforeaneat 2 requirecENcVzsp: 2009
‘TUTORIAL 5: STEEL CONNECTIONS 1
oO DETERMINE THE NUMBER OF Meo (4.8)
bots REQUIRED FoR THE Folrowing PoKeLE
cover butt Joint.
WRAT 18 THE THICKNESS AND MINIMUM
POSSIBLE LENTTH oF THE coveR fares 7
wH? $
“yi cenern 00% 16 fe
Go) =
Cot) S00 16 tt
Se 4b0 EN
uty
cover plates ;
peo wie x 2 THER x MIN 2 Comm
(Aisume DAULED eves au sau eraes)
PROVIDE A NEAT DimENssIONED StETeH (To scare)
oF THE TowT
Papp SOAS yy 30
$
| ‘ 1
et + ) toe f
+ + +f tit +), pee \
ISO KISOKIZL 2
secrien
Ate)
sPuice cee veer
150 Wie yy
S50 TS a + + 4] p= sso kd
wet, Ht te te 2 uur,
PRILED HOLES
PLAN SAWN/ Rewer e DAEs
Ya YN
DETERMINE tHE S1ZE OF $6 BOLTS AND THICKNESS
PLATES . CHECK ANKLE CAPACITYENcvaso: 2000
TUTORIAL 6: STEEL CONNECTIONS 2
See 30 kn (se:
cet dete tuet)
ae tor
Stee oF Baits, See
Waa as
GD Meee Csunence "8 )
Bos xles qi
8 bouts ‘A’
Ag pe
eae
200 kN fan
Joy, l0e, 108 (ner)
ve oe Se OF canes Ge HUTS Ora! me 8!
Cate WD vee Pet meter
(ah
Sonn
(uery
ty .
Se
sep 80}
eucer Genes a a ele,ENov2s0: 2000
‘TUTORIAL 7: TENSION & COMPRESSION STEEL MEMBERS
+000)
, eee
3000
tooo
oe
ELEVATION OF LIFTING DEVICE.
MEMBER DESCRIPTIONS
‘A~Band B ~C: Single equal eg angles, bolted through one leg. Gr 8.8 belts, died
hoes
‘A~Dand DC: Goluran(H.) sections, al ends pinaes,& and C held inp
(8 E Beam (1-) ful fixed, pinned but held in postion, D propped on minor
‘QUESTION
41. Determine the ulimate forces inthe members.
2. Using the resistance tables inthe Red book, choose the LIGHTEST member
3. Check member sizes and bolts by calculation,
lendemess ofthe tension members
Note: Comment onENov2s0, 2000
TUTORIAL 8: STEEL BEAMS
) shows the cross section through a compound Class 2 steel colurm
‘of a pair of channels adequately battened together (shown dotted),
‘The column may be taken as pinned atthe top and ful
TAPER FAKE = 3m
Figure *1@)
Determine the maximum ultimate axial comprossive load resistance of the
‘column,
QUESTION 2
For the 457 X 191 X67 [beam shown:
—
llr
a
4. Check in A-B and B-C ifthe ultimate bending resistance is satisfactory
Loads are utimate and nat destabilizing. Which is the etical zone for
4, Check ifthe beam is satisfactory in bending.
Note: the beam's compression flange is restrained at A. 8, C-and D.