Professional Documents
Culture Documents
Item
Page
ANSI/AWWA Compact & Full Body Pipe Fittings:
Mechanical & Flange Joint C153.3-9
Mechanical & Plain End C153..3-5,8
Mechanical & Swivel Joint C153.3,4,6
Mechanical Joint Offsets, Wyes, Reducers C153.4,8
Mechanical Joint Sleeves, Caps, Plugs C1539,10
Mechanical Joint Tapped Tees C153...9
Swivel by Swivel Hydrant Joint C153..5,7
Plain End by Plain End Joint C153..8
Mechanical & Flange Joint C110 Full Body......13-22
Mechanical & Plain End Joint C110.13-15,19
Mechanical & Swivel Joint C110.....22
Mechanical Joint Sleeves, Caps, Plugs C110.20,21
Mechanical Joint Offsets, Wyes, Crosses C110..18,21
Mechanical Joint Tapped Tees C110.16
Mechanical by FIPT Joint, Reducers C110..14,19
Plain End by Plain End Joint C11019
Swivel by Swivel Hydrant Joint C110....23
Flange by Flange Joint C110.30-33
Flange by Flare Joint, Reducers, Wyes C110....33-35
Flange by Flange Joint w/Base C110..35,36
Flanged Sludge Shoe C110.36
Flanges Threaded and Blind C110...36
Push on & Flange Joint Compact...24,25,27-29
Push on & Plain End Joint Compact.26
Push on & Swivel Joint Compact...27
Push on Joint Adapters, Caps, Plugs, Compact21,28
Push on Tap Tees, Crosses, Wyes, Reducers Compact..28,29
Adapters Mechanical, Flange, Plain End Joint C153..9
Adapters Mechanical & Flange Joint C110.20
Adapter Flanges w/Setscrews..37,48
Tapping Sleeve C153...12,22,64
Item
Page
Product Submittals and Installation:
20U Protective Fusion Bonded Epoxy....56,57
21U Cement, Mortar, Asphaltic Materials..58
22U Domestic ANSI/AWWA C110 Fittings..59
22U Non-Domestic ANSI/AWWA C110 Fittings..60
23U Domestic ANSI/AWWA C153 Fittings..61
23U Non-Domestic ANSI/AWWA C153 Fittings..62
24U Mechanical Joint Retainer Gland...63
25U Pipe Tapping Sleeves..64
26U - Domestic Push on Tyton Joint Fittings....65
26U Non-Domestic Push on Tyton Joint Fittings...66
27U ANSI/AWWA C111 Fasteners...53
28U Domestic ANSI/AWWA C110 Flange Fittings....67
28U Non-Domestic ANSI/AWWA C110 Flange Fittings.68
29U Domestic ASTM A48 Valve Boxes..69
30U Non-Domestic ASTM A48 Valve Boxes..70
31U Mechanical and Push on Joint Gaskets29,71,72
Accessories:
NOTICE: 1) Weights published in this catalog are guideline for shipping purposes only. Actual weights may vary as some fittings
are manufactured in multiple locations. All fittings meet the ANSI/AWWA standards. For weights of specific fittings,
contact Tyler Union Waterworks.
2) For the flange thickness or laying lengths of specific fittings, please contact Tyler Union Waterworks
2
Size A Dia.
BOLTS
C Dia.
D Dia.
F Dia.
J Dia.
K1 Dia.
K2 Dia.
Size
No.
2.51
2.50
3.50
3.60
2.61
4.75
6.19
6.89
.58
.62
.36
.30
x3
3.96
2.50
4.84
4.94
4.06
6.19
7.62
7.69
.58
.62
.39
.33
.x3
4.80
2.50
5.92
6.02
4.90
7.50
9.06
9.12
.60
.75
.39
.34
x3
6.90
2.50
8.02
8.12
7.00
9.50
11.06
11.12
.63
.88
.43
.36
x3
9.05
2.50
10.17
10.27
9.15
11.75
13.31
13.37
.66
1.00
.45
.38
x4
10 11.10
2.50
12.22
12.34
11.20
14.00
15.62
15.62
.70
1.00
.47
.40
x4
12 13.20
2.50
14.32
14.44
13.30
16.25
17.88
17.88
.73
1.00
.49
.42
x4
14 15.30
3.50
16.40
16.54
15.44
18.75
20.31
20.25
.79
1.25
.55
.47
x4
10
16 17.40
3.50
18.50
18.64
17.54
21.00
22.56
22.50
.85
1.31
.58
.50
x4
12
18 19.50
3.50
20.60
20.74
19.64
23.25
24.83
24.75
1.00
1.38
.68
.54
x4
12
20 21.60
3.50
22.70
22.84
21.74
25.50
27.08
27.00
1.02
1.44
.69
.57
x4
14
24 25.80
3.50
26.90
27.04
25.94
30.00
31.58
31.50
1.02
1.56
.75
.61
x5
16
30 32.00
4.00
33.29
33.46
32.17
36.88
39.12
39.12
1.31
2.00
.82
.66
1x6
20
36 38.30
4.00
39.59
39.76
38.47
43.75
46.00
46.00
1.45
2.00
1.00
.74
1x6
24
42 44.50
48 50.80
4.00
4.00
45.79
52.09
45.96
52.26
44.67
50.97
50.62
57.50
53.12
60.00
53.12
60.00
1.45
1.45
2.00
2.00
1.35
1.35
.82
.90
1
1.
1x6
1x6
28
32
NOTE: 2 Inch MJ ASTM A536 ductile iron Compact fittings (2"-22.5 bend, 2"-45 bend, 2"-90 bend, 2"x12" solid sleeve, 2"x2" tee, 4"x2"
tee, and 4"x2" reducer) are available beginning 2012. Call Tyler Union for availability or additional product dimensions.
*NOTE: Contact Tyler Union for 54"-64" product information.
NOTE: The fitting laying lengths provided are approximate, contact Tyler Union Waterworks for the
laying length of a specific fitting.
256772_utility catalog.pdf 3
12/15/08 8:24:18 AM
Listed
BENDS
90Bends (1/4)
Size
Dimensions
T
*A
45 Bends (1/8)
Weight
imensions
D
*A
R
Weight
imensions
D
*A
R
2.51
imensions
D
*A
R
15
Weight
.34
3.5
2.5
19
2.00
2.41
.35
4.0
3.0
22
2.50
3.56
20
1.75
3.81
.37
6.5
6.0
49
3.50
7.25
39
2.25
6.35
.39
7.5
7.0
64
4.00
8.44
56
2.85 11.80
50
2.06 15.80
45
10
.41
9.5
9.0
102
5.01 10.88
78
3.35 14.35
66
2.32 18.36
59
12
.43 10.5
10.0
129
5.98 13.25
102
3.86 16.90
87
2.56 20.90
82
14
.51 12.0
11.5
214
5.50 12.06
155
3.93 17.25
142
16
.52 13.0
12.5
273
5.98 13.25
204
3.98 17.50
178
18
.59 15.5
14.0
411
6.50 12.36
292
7.50 30.19
286
20
.60 17.0
15.5
519
7.00 13.59
372
8.50 35.19
376
24
.62 17.0
15.5
721
7.50 14.89
490
9.00 37.69
512
930
9.31
1.50
11 Bends (1/32)
Weight
10.50
17
22 Bends (1/16)
1.25
2.53
16
18
1.50
5.12
18
31
1.50
5.12
29
716
6.75 21.36
665
36
7.75 26.39
960
42
48
.90 33.25 30.75 2990
15.00 30.17 2090
10.00 27.70 1760
6.50 40.61 1475
*NOTE: "A" dimensions are approximate, contact Tyler Union for the laying length of a specific fitting
**Note: 2 Inch Compact ductile iron 22.5, 45, and 90 degeree bends available in 2012. Call Tyler Union for information.
OFFSETS
MJ x MJ
BENDS
MJ x PE
Size
Dimensions
L 1
L
4
4
4
4
6
6
6
6
8
8
8
10
12
6
12
18
24
6
12
18
24
6
12
18
12
6
10
18
22
28
12
18
24
30
13
19
25
21
17
--
---
--
17.5
--
--
---
---
---
Weights
MJxMJ MJxPE
42
52
58
70
50
65
82
91
79
96
116
136
137
--------------
Size
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
Dimensions
*A
R
1.25
1.50
1.50
1.75
2.00
2.30
2.50
2.50
3.00
3.00
3.00
3.75
4.00
5.00
5.50
Weight
5.08
16
7.61
18
10.15
29
12.69
45
15.23
59
17.77
82
20.31 136
20.31
157
25.38
283
25.38
374
25.38
487
32.97
600
34.55
820
42.71 1180
47.35 1475
4
BENDS
90Bend MJ x PE (1/4)
Size
Dimensions
*A Y
3
4
6
8
10
12
14
16
20
24
30
.34
.35
.37
.39
.41
.43
.51
.52
.57
.62
.68
90Bend MJ x Flange
(1/4)
Size
3
4
6
8
10
12
14
16
3.5
4.0
6.0
7.5
9.5
9.0
12.0
13.0
15.0
17.0
21.5
9.0
9.5
11.5
13.0
15.0
14.4
20.0
21.0
23.0
25.0
30.5
2.5
3.0
5.0
7.0
9.0
6.0
11.5
12.5
13.5
15.5
--
Dimensions
*A R
.34 3.5
2.5 5.5
.35 4.0
3.0 6.5
.37 6.0
5.0 8.0
.39 7.5
7.0 9.0
.41 9.5
9.0 11.0
.43 10.5 10.0 12.0
.51 12.0 11.5 14.0
.52 13.0 12.5 15.0
45Bend MJ x PE (1/8)
Weight
Dimensions
*A
Y
R
18 2.0
26 2.5
45 3.2
64 4.0
108 5.0
114 6.0
219 5.5
254 6.0
400 7.0
710
7.5
865 10.5
7.5
8.0
8.7
9.5
10.5
11.5
13.4
14.0
15.3
16.6
19.5
2.41
3.56
5.49
8.44
10.88
13.25
10.85
13.25
13.97
14.69
--
Weight
17
22
38
55
78
104
165
206
290
460
715
45Bend MJ x Flange
(1/8)
Weight
21
28
45
73
113
141
217
280
Dimensions
*A
R
F
...
...
2.50 3.56
3.25 5.49
4.25 7.93
5.00 9.76
6.00 12.19
5.50 10.85
6.00 12.02
..
4.0
5.0
5.5
6.5
7.5
8.5
9.5
Weight
..
34
57
83
122
159
207
290
1.50 7.00
1.75 7.25
2.25 7.75
2.84 8.34
3.35 8.85
3.50 9.00
3.93 11.93
3.98 11.98
--9.00 17.66
6.75 15.75
Weight
2.51
3.81
6.35
11.80
14.35
12.70
17.25
17.50
-37.69
--
19
20
33
51
66
89
152
181
-455
600
22 Bend MJ x Flange
(1/16)
Dimensions
*A
R
F
...
1.75
2.25
2.50
3.00
3.50
...
3.81
5.35
7.62
10.16
12.70
Weight
..
..
4.0
34
5.0
57
5.5
83
6.5 122
7.5 159
Dimensions
*A
Y
R
1.25 6.75
1.50 7.00
1.50 7.00
2.05 7.55
2.31 7.81
2.56 8.06
2.59 10.59
2.62 10.62
--9.00 26.12
---
Weight
7.62
5.12
5.12
15.80
18.36
20.90
21.25
21.50
-12.00
--
15
20
32
44
60
79
137
161
-475
--
11 Bend MJ x Flange
(1/32)
Dimensions
*A
R
F
...
1.50
1.50
1.75
2.00
2.25
...
5.12
5.12
7.70
10.25
12.82
..
4.0
5.0
5.5
6.5
7.5
Weight
..
19
30
50
75
88
Dimensions
C
D
6.90 11.2
6.81
7.98
6.0
74
*NOTE: "A" dimensions are approximate, contact Tyler Union for the laying length of a specific fitting
256772_utility catalog.pdf 5
12/15/08 8:24:18 AM
CROSS
TEES
MJ Tee
Size
MJ x FE Tee
T1
*H
Dimensions
*J1
MJ x Swivel Tee
*J2
*J3
MJ
Cross
Weights
MJxFE
MJxS
Cross
3
.34
.34
3.5
3.50
5.5
...
26
29
...
31
4x3
.35
.34
3.5
4.00
6.5
...
35
34
...
39
4
.35
.35
4.0
4.00
6.5
...
36
39
...
45
6x3
.37
.34
4.0
4.00
6.5
...
51
54
...
...
6x4
.37
.35
4.0
5.00
8.0
...
52
57
...
62
6
.37
.37
5.0
5.00
8.0
10.50
66
68
77
79
8x3
.39
.34
4.0
6.50
9.0
...
56
...
...
...
8x4
.39
.35
4.5
6.50
9.0
...
72
82
...
84
8x6
.39
.37
5.5
6.50
9.0
11.50
79
81
105
98
8
.39
.39
6.5
6.50
9.0
11.50
90
101
116
112
10x3
.41
.34
4.0
7.50
11.0
...
80
...
...
...
10x4
.41
.35
4.5
7.50
11.0
...
82
92
...
98
10x6
.41
.37
5.5
7.50
11.0
13.00
99
116
114
121
10x8
.41
.39
6.5
7.50
11.0
13.00
116
128
138
135
10
.41
.41
7.5
7.50
11.0
...
132
144
...
156
12x3
.43
.34
4.0
8.75
12.0
...
99
...
...
...
12x4
.43
.35
4.5
8.75
12.0
...
108
118
...
119
12x6
.43
.37
5.5
8.75
12.0
14.25
119
133
132
138
12x8
.43
.39
6.5
8.75
12.0
14.25
126
146
149
149
12x10
.43
.41
7.5
8.75
12.0
...
159
174
...
187
12
.43
.43
8.75
8.75
12.0
...
171
198
...
202
14x6
.51
.44
6.5
10.50
14.0
16.00
183
205
211
210
14x8
.51
.45
7.5
10.50
14.0
...
211
...
...
231
14x10
.51
.46
8.5
10.50
14.0
...
229
244
...
255
14x12
.51
.47
9.5
10.50
14.0
...
245
284
...
269
14
.51
.51
10.5
10.50
14.0
...
281
291
...
299
16x6
.52
.45
6.5
11.50
15.0
17.00
222
230
243
250
16x8
.52
.46
7.5
11.50
15.0
...
245
248
...
264
16x10
.52
.47
8.5
11.50
15.0
...
265
287
...
286
16x12
.52
.48
9.5
11.50
15.0
...
277
312
...
312
16x14
.52
.51
10.5
11.50
15.0
...
317
348
...
...
16
.52
.52
11.5
11.50
15.0
...
337
324
...
451
18x6
.59
.44
6.5
14.50
15.5
18.00
275
261
279
...
18x8
.59
.45
7.5
14.50
14.5
...
280
351
...
...
18x10
.59
.47
8.5
12.50
...
...
286
...
...
...
18x12
.59
.49
9.5
12.50
...
...
372
...
...
...
18x14
.59
.56
10.5
12.50
...
...
415
...
...
...
18x16
.59
.57
11.5
12.50
...
...
445
...
...
...
18x18
.59
.59
13.0
12.50
...
...
490
...
...
...
NOTE: Contact TU Inside Sales representative for MJ Crosses larger than 16 inch. MJxSwl Weights include swivel gland.
**NOTE: 2"x2" and 4"x2" Compact C153 tees available in 2012. Call Tyler Union for information.
*NOTE: "H" and "J" dimensions are approximates. contact Tyler Union for the laying length of specific fittings
TEES (Continued)
Listed
MJ GLANDS
Glands
MJ Tee
Size
20x6
20x8
20x10
20x12
20x14
20x16
20x18
20x20
24x6
24x8
24x10
24x12
24x14
24x16
24x18
24x20
24x24
30x6
30x8
30x12
30x16
30x18
30x20
30x24
30x30
36x12
36x16
36x24
36x30
36x36
42x12
42x24
42x30
42x36
42x42
48x12
48x24
48x36
48x42
48x48
NOTE: "H"
MJ x FE Tee
T1
*H
Dimensions
*J1
*J2
MJ x Swivel Tee
*J3
.60
.44
7.0
16.0
17.0
19.5
.60
.45
8.0
14.0
...
...
.60
.47
9.0
14.0
...
...
.60
.49
10.0
14.0
...
...
.60
.56
11.0
14.0
...
...
.60
.57
12.0
14.0
...
...
.60
.59
13.0
14.0
...
...
.60
.60
14.0
14.0
...
...
.62
.44
7.0
18.0
19.0
21.5
.62
.45
8.0
16.0
...
...
.62
.47
9.0
16.0
...
...
.62
.49
10.0
18.0
...
...
.62
.56
11.0
16.0
...
...
.62
.57
12.0
19.5
...
...
.62
.59
13.0
16.0
...
...
.62
.60
15.0
17.0
...
...
.62
.62
17.0
17.0
...
...
.66
.36
7.0
20.0
...
...
.66
.38
8.5
20.0
...
...
.66
.42
10.0
20.0
...
...
.66
.50
12.5
20.0
...
...
.66
.52
14.0
20.0
...
...
.66
.57
15.0
20.0
...
...
.66
.61
16.0 20.0
...
...
.66
.66
20.0
20.0
...
...
.74
.50
10.5
23.5
...
...
.74
.50
12.5
23.5
...
...
.74
.61
16.0
23.5
...
...
.74
.66
20.0
23.5
...
...
.74
.74
23.5
23.5
...
...
.82
.62
10.0
29.5
...
...
.82
.62
20.0
30.0
...
...
.82
.66
22.0
30.0
...
...
.82
.74
30.0
30.0
...
...
.82
.82
30.0
30.0
...
...
.90
.62
23.0
32.0
...
...
.90
.62
33.5
32.0
...
...
.90
.82
33.5
33.5
...
...
.90
.82
33.5
33.5
...
...
.90
.82
33.5
33.5
...
...
and "J" are approximate, contact Tyler Union
MJ
Weights
MJxFE
MJxS
Size Weight
Size Weight
18
20
24
30
36
42
48
4
6
8
10
12
14
16
3
4
5
6
9
10
17
21
22
32
37
85
115
180
275
335
362
358
390
...
...
417
...
...
460
...
...
475
...
...
530
...
...
560
...
...
605
...
...
465
451
457
475
...
...
516
...
...
Swivel x Solid Adapter
549
580
...
with Swivel Gland
585
...
...
Size
by
Wall
625
744
...
Laying
Length
Thickness
Weight
675
...
...
6x13
.37
52
740
...
...
6x18
.37
65
844
...
...
6x24
.37
69
700
...
...
8x12
.39
52
739
...
...
739
...
...
959
...
...
975
...
...
995
...
...
1160
...
...
1323
...
...
1103
...
...
1350
...
...
1498
...
...
Swivel x Swivel Adapter
1555
...
...
Size by
Wall
1910
...
...
Laying Length Thickness Weight
1410
...
...
6x12
.37
28
2295
...
...
6x18
.37
49
2337
...
...
6x24
.37
52
3000
...
...
3169
...
...
MJxSwivel Tee Weights include swivel
2500
...
...
gland
2822
...
...
3982
...
...
4100
...
...
4251
...
...
for the specific laying length of a fitting
7
Sizes 3"
UL & 3"-10" FM Listed
For Fire Main Equipment
REDUCERS
WYES/LATERAL
MJ x MJ
Size
4x3
6x3
6x4
Dimensions
8x4
1
Size
A
Y
T
T
Weights
8x6
3
2.5
7.5
.34
.34
36
10x4
4x3
2.0
8.5
.35
.34
39
10x6
4
2.5
8.5
.35
.35
45
10x8
6x4
1.5
11.0
.37
.35
67
12x4
6
3.0
13.0
.37
.37
85
12x6
8x4
0.5
13.0
.39
.35
86
12x8
8x6
2.0
14.5
.39
.37 109
12x10
8
3.5
16.0
.39
.39 117
14x6
14x8
10x4
0.0
15.0
.41
.35 112
14x10
10x6
1.0
16.0
.41
.37 129
14x12
10x8
2.5
17.0
.41
.39 162
16x6
10
3.5
19.0
.41
.41 199
16x8
12x4
0.0
16.5
.43
.35 141
16x10
12x6
1.5
18.5
.43
.37 170
16x12
12x8
1.5
18.5
.43
.39 177
16x14
12x10 3.0
20.0
.43
.41 216
18x8
12
4.5
22.5
.43
.43 269
18x10
14
6.0
25.0
.51
.51 476
18x12
t16x6
0.0
21.0
.52
.45 300
18x14
t16x8
0.5
22.5
.52
.46 349
18x16
16x12 3.5
25.0
.52
.48 471
20x10
16
6.5
28.0
.52
.52 635
20x12
*Not included in AWWAC153, laying lengths are approx. 20x14
Rated at 250 psi.
20x16
20x18
MJ x FE Flange Dimensions are on inside
24x12
front cover.
24x14
24x16
24x18
24x20
30x16
30x18
30x20
*MJ x PE x MJ Tee
30x24
36x16
Dimensions
Size
T
T1
H
J1
Z Weights 36x20
36x24
6 .37 .37 5.0 5.0 11.5 57
36x30
8x6 .39 .37 5.5 6.5 11.5 79
8 .39 .39 6.5 6.5 12.5 83
42x30
10 .41 .41 7.5 7.5 13.0 133
42x36
48x30
*Note: Laying lengths are approximate, contact
Tyler Union for the laying length of a specific fitting
48x36
48x42
*Wyes
PExMJSEB
T1
.35
.37
.37
.39
.39
.41
.41
.41
.43
.43
.43
.43
.51
.51
.51
.51
.52
.52
.52
.52
.52
.59
.59
.59
.59
.59
.60
.60
.60
.60
.60
.62
.62
.62
.62
.62
.66
.66
.66
.66
.74
.74
.74
.74
.82
.82
.90
.90
.90
.34
.34
.35
.35
.37
.35
.37
.39
.35
.37
.39
.41
.44
.45
.46
.47
.45
.46
.47
.48
.51
.45
.47
.49
.56
.57
.47
.49
.56
.57
.59
.49
.56
.57
.59
.60
.50
.54
.57
.61
.50
.57
.61
.66
.74
.74
.66
.74
.82
MJLEBxPE
Dimensions
MJ
SEB
LEB
L
L
L
3.0
5.0
4.0
5.0
4.0
7.0
5.0
4.0
9.0
7.0
5.0
4.0
9.0
7.0
5.0
4.0
11.0
9.0
7.0
5.0
4.0
14.0
12.0
10.0
8.0
7.0
14.0
12.0
10.0
8.0
7.0
16.0
14.0
12.0
10.0
8.0
30.0
28.0
24.0
10.0
30.0
36.0
19.0
15.5
20.0
15.5
40.0
28.0
15.5
8.5
10.5
9.5
10.5
9.5
12.5
10.5
9.5
14.5
12.5
10.5
9.5
17.0
15.0
13.0
12.0
19.0
17.0
15.0
13.0
12.0
22.0
20.0
18.0
16.0
15.0
22.0
20.0
18.0
16.0
15.0
24.0
22.0
20.0
18.0
16.0
39.0
37.0
33.0
24.5
...
45.0
33.0
24.5
...
...
...
...
...
8.5
10.5
9.5
10.5
9.5
12.5
10.5
9.5
14.5
12.5
10.5
9.5
14.5
12.5
10.5
9.5
16.5
14.5
12.5
10.5
12.0
19.5
17.5
15.5
16.0
15.0
19.4
17.5
17.8
15.8
15.0
21.4
21.8
19.8
18.0
16.0
...
...
...
...
...
...
...
...
...
...
...
...
...
PE
L
PE x PE
MJ
14.0 18
16.0 28
15.0 28
16.0 36
15.0 39
18.0 53
16.0 59
15.0 54
20.0 67
18.0 64
16.0 57
15.0 63
22.5 104
20.5 104
18.5 100
17.5 100
24.5 132
22.5 136
20.5 128
18.5 120
20.0 140
27.5 201
25.5 196
23.5 175
24.0 180
23.0 194
27.5 225
25.5 214
26.0 208
24.0 225
23.0 233
29.5 320
30.0 314
28.0 325
26.0 325
24.0 315
... 475
... 495
... 525
... 478
... 789
... 970
... 770
... 838
... 1067
... 1116
... 1852
... 1632
... 1486
Weights
SEB LEB
17
25
26
34
38
46
48
52
61
58
62
61
107
107
102
101
131
128
124
123
139
180
180
170
181
180
210
208
198
215
220
302
325
319
310
305
565
590
560
495
890
874
746
725
...
...
...
...
...
17
27
27
36
39
51
52
52
68
66
65
65
112
108
100
100
141
136
128
119
138
195
185
190
200
190
210
210
205
222
...
300
322
340
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
PE
18
20
26
33
30
...
49
47
60
54
60
57
...
...
...
100
128
136
123
113
133
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
SOLID SLEEVES
3"-12" 14"-24"
3"-12" 14"-24"
MJ Plug
MJ Cap
Size
Weights
Plugs
Caps
Size
9
9
18
25
36
47
76
98
138
158
223
355
688
1091
1455
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
Dimensions
T
Max.
Tap
.46
.46
.46
.46
.56
.56
.62
.62
.65
.66
.68
.66
.74
.82
.90
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
*TAPPED TEE
8
10
18
26
32
46
85
94
121
149
210
345
626
723
974
MJ x FE Flange
Dimensions are
on inside front
cover.
Short
T
Dimensions
L 1
Long
L2
Weights
Short
Long
3
.34
7.5
12
4
.35
7.5
12
6
.37
7.5
12
8
.39
7.5
12
10
.41
7.5
12
12
.43
7.5
12
14
.56
9.5
15
16
.57
9.5
15
18
.68
9.5
15
20
.69
9.5
15
24
.75
9.5
15
30
.66
15.0
15
30
.66
...
24
36
.74
15.0
15
36
.74
...
24
42
.82
...
24
48
.90
...
24
Note: 2"x12" C153 Sleeves available, call
13
22
19
25
28
39
38
55
48
68
62
81
116
146
138
174
160
230
212
269
272
380
500
...
...
640
725
662
...
925
...
1146
...
1455
for information
ADAPTERS
Size
Dimensions
T
*L
Max. Tap
Weights
3
.34
6
2
19
4
.35
6
2
23
6
.37
6
2
35
8
.39
6
2
54
10
.41
6
2
68
12
.43
6
2
88
16
.52
6
2
164
Note: "L" dimensions are approximate, contact Tyler
Union for laying length of a spcific fitting
MJ x FE
Size
3
4
6
8
10
12
14
16
18
20
24
30
36
.34
.35
.37
.39
.41
.43
.51
.52
.56
.60
.62
.66
.74
Dimensions
L 1
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*6
*7
*8
FE x PE
L2
12
12
12
12
12
12
12
12
...
...
...
...
...
Weights
MJxFE
FExPE
18
26
36
50
60
88
127
155
195
275
305
470
750
...
23
35
50
69
88
...
149
...
...
...
...
...
Size
4
6
8
10
12
Listed
MJ x FE
Cutting-In Sleeve with Dual Purpose Accessories
For Pipe Size
Dimensions
L
4.80-5.00 O.D.
6.90-7.10 O.D.
9.05-9.30 O.D.
11.10-11.40 O.D.
13.20-13.50 O.D.
10
10
10
10
10
L 1
Shipping Wt.
Assembled
9.5
9.5
9.5
9.5
9.5
.35
.37
.39
.41
.43
33
50
67
122
157
Flanged ends are faced and drilled per ANSI/AWWA C110/A21.10. Mechanical joint ends are designed to receive both standard and oversize gray or ductile iron pipe as shown above.
MJ x FE Flange
TYPICAL CUTTING-IN SLEEVE INSTALLATIONS
Dimensions are
on inside front
VALVE
cover.
INSTALLATIONS
METER SETTINGS
3
4
6
8
10
12
14
16
18
20
24
Pressure
Rating,
psi
Gland
O.D.
B
350
350
350
250
250
150
250
200
200
200
150
7.69
9.12
11.12
13.37
15.62
17.88
20.25
22.50
24.75
27.00
31.50
3.96
4.80
6.90
9.05
11.10
13.20
15.30
17.40
19.50
21.60
25.80
256772_utility catalog.pdf 10
50-56
50-56
50-56
50-56
50-56
50-56
53-56
53-56
53-56
53-56
53-56
No of
Set
Screws
4
4
6
9
12
16
20
24
24
28
32
Size of
Set
Screws
x2
x2
x2
x2
x2
x2
x2
x2
x2
x3
x3
Gland Weight
Weight w/Acces.
5
6
11
13
18
23
44
51
62
73
93
7
13
20
25
33
38
55
64
72
91
118
12/15/08 8:24:21 AM
4" Size
6"-8"-10"-12" Sizes
MJ Compact Split Repair Glands
Size
4
6
8
10
12
Weight
Lbs.
4.0
5.0
6.0
7.7
10.2
11
COMPACT
Sample Specification
Ductile ron echanical joint tapping sleeves furnished by Tyler Union Waterworks are produced in accordance
with manufacturer's standards. Chemical and physical properties of the ductile iron are in accordance
requirements of ANSI/AWWA C153/A21.53 and ASTM A536. Coatings are NSF-61, NSF-372, Annex G approved and
conform with AWWA C104. Flange recess dimensions per MSS SP-60. Tapping sleeve meets requirements of MSS SP-111
General Installation Instructions for Tyler
apping Sleeves
1. Clean pipe - insert side gasket into back half of gasket grooves. Make sure ends are flush with or slightly protrude into the end gasket seating area.
2. Bolt sleeve halves together and trim side gaskets as necessary. MAKE SURE SLEEVE WILL ROTATE FREELY ON
PIPE.
3. Install end gaskets, locating cut ends 90 from
side gasket. If pipe is maximum OD, stretch
gasket to make certain cut ends match with no
gap in between.
4. Install glands and bolts - rotate sleeve to desired
position. Be sure pipe is centered inside the sleeve.
5. Tighten gland bolts alternately, using 80 to 90
foot pounds.
6. After assembly, PRESSURE TEST ALL JOINTS BEFORE TAPPING. If additional tightening is
required, release pressure and relax tension on
gland bolts before tightening side bolts.
For Cast Iron Ductile Iron, and PVC C900 Pipe
Mechanical joint tapping sleeves - for 6" through
12" cast iron ductile iron, or PVC pipe.
Outlet flange per ANSI/AWWA C153/A21.53
Gaskets furnished meet AWWAC111 and ASTM D2000-AA.
Working pressure-250 p.s.i.
Gaskets available in SBR only
Joint deflection is not recommended
Size
256772_utility catalog.pdf 12
6x4
5.016
6
7.016
8x4
5.016
8x6
7.016
8
9.016
10x4
5.016
10x6
7.016
10x8
9.016
10
11.016
12x4
5.016
12x6
7.016
12x8
9.016
12x10 11.016
12
13.016
.250
.312
.250
.312
.312
.250
.312
.312
.312
.250
.312
.312
.312
.312
Dimensions
C
D
7.50
9.50
7.50
9.50
11.75
7.50
9.50
11.75
14.25
7.50
9.50
11.75
14.25
17.00
15.75
15.75
16.50
16.50
16.50
24.00
24.00
24.00
24.00
26.50
26.50
26.50
26.50
26.50
8.00
8.00
9.00
9.00
9.00
11.00
11.00
11.00
11.00
12.00
12.00
12.00
12.00
12.00
12.75
12.75
13.50
13.50
13.50
20.75
20.75
20.75
20.75
23.25
23.25
23.25
23.25
23.25
.D. Range
O
DI
Min. Max.
6.85
6.85
9.00
9.00
9.00
11.04
11.04
11.04
11.04
13.14
13.14
13.14
13.14
13.14
7.15
7.15
9.35
9.35
9.35
11.45
11.45
11.45
11.45
13.56
13.56
13.56
13.56
13.56
Weight
DI
104
108
134
140
148
236
240
246
257
273
286
292
303
320
12
12/15/08 8:24:21 AM
*2 2.50
3 3.96
4 4.80
6 6.90
8 9.05
10 11.10
12 13.20
14 15.30
16 17.40
18 19.50
20 21.60
24 25.80
30 32.00
36 38.30
42 44.50
48 50.80
2.50
2.50
2.50
2.50
2.50
2.50
2.50
3.50
3.50
3.50
3.50
3.50
4.00
4.00
4.00
4.00
K 1
K2
3.39
4.84
5.92
8.02
10.17
12.22
14.32
16.40
18.50
20.60
22.70
26.90
33.29
39.59
45.79
52.09
3.50
4.94
6.02
8.12
10.27
12.34
14.44
16.54
18.64
20.74
22.84
27.04
33.46
39.76
45.96
52.26
2.61
4.06
4.90
7.00
9.15
11.20
13.30
15.44
17.54
19.64
21.74
25.94
32.17
38.47
44.67
50.97
28
28
28
28
28
28
28
28
28
28
28
28
20
20
20
20
1
1
1
1
4.75
6.19
7.50
9.50
11.75
14.00
16.25
18.75
21.00
23.25
25.50
30.00
36.88
43.75
50.62
57.50
6.25
7.69
9.12
11.12
13.37
15.69
17.94
20.31
22.56
24.83
27.08
31.58
39.12
46.00
53.12
60.00
6.25
7.69
9.12
11.12
13.37
15.62
17.88
20.25
22.50
24.75
27.00
31.50
39.12
46.00
53.12
60.00
.75
.94
1.00
1.06
1.12
1.19
1.25
1.31
1.38
1.44
1.50
1.62
1.81
2.00
2.00
2.00
.62
.62
.75
.88
1.00
1.00
1.00
1.25
1.31
1.38
1.44
1.56
2.00
2.00
2.00
2.00
1.12
1.37
1.50
1.63
1.75
1.75
1.75
2.00
2.06
2.13
2.19
2.31
2.75
2.75
2.75
2.75
.31
.31
.31
.31
.31
.31
.31
.31
.31
.31
.31
.31
.38
.38
.38
.38
.63
.63
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
1.00
1.00
1.00
1.00
.44
.52
.65
.70
.75
.80
.85
.89
.97
1.05
1.12
1.22
1.50
1.80
1.95
2.20
Bolt
No. Size
*2
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
2
4
4
6
6
8
8
10
12
12
14
16
20
24
28
32
1
1
1
1
Wt. of Gland, Pipe
Bolt
Bolt Torque Bolts and
Barrel
Length
Ft/Lbs. Gasket, Lbs. O.D.
3
3
3
3
4
4
4
4
4
4
4
5
6
6
6
6
45-60
45-60
75-90
75-90
75-90
75-90
75-90
75-90
75-90
75-90
75-90
75-90
100-120
100-120
120-150
120-150
5
7
10
16
25
30
40
45
55
65
85
105
220
301
389
477
2.50
3.96
4.80
6.90
9.05
11.10
13.20
15.30
17.40
19.50
21.60
25.80
32.00
38.30
44.50
50.80
256772_utility catalog.pdf 13
12/15/08 8:24:22 AM
MJ x FIPT ECCENTRIC
REDUCER
Dimensions
Size
L
Weights
6x2
8x2
13
15
51
71
BENDS
90 Bends (1/4)
90 MJ x MJ (1/4)
90 MJ x FE (1/4)
90 MJ x PE (1/4)
Size
Dimensions
Y
*2
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
2.25
4.0
4.5
6.0
7.0
9.0
10.0
11.5
12.5
14.0
15.5
18.5
21.5
24.5
27.5
30.5
3.25
5.5
6.5
8.0
9.0
11.0
12.0
14.0
15.0
16.5
18.0
22.0
25.0
28.0
31.0
34.0
MJxMJ
Weights
MJxPE
...
13.5
14.5
16.0
17.0
19.0
20.0
22.0
23.0
24.5
26.0
30.0
33.0
36.0
16
26
56
88
123
189
268
380
552
625
862
1423
1942
2629
3410
4595
...
36
53
80
119
181
252
...
470
600
775
1301
1920
2310
...
...
MJxFE
...
...
51
75
118
168
288
...
465
577
...
1150
...
...
...
...
256772_utility catalog.pdf 14
14
12/15/08 8:24:22 AM
BENDS
45 MJ (1/8)
45 MJ x PE (1/8)
45 MJ x FE (1/8)
Size
Dimensions
Y
*2
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
1.96
3.62
4.81
7.25
8.44
10.88
13.25
12.06
13.25
14.50
16.88
18.12
27.75
35.00
42.25
49.50
1.8
3.0
4.0
5.0
5.5
6.5
7.5
7.5
8.0
8.5
9.5
11.0
15.0
18.0
21.0
24.0
MJ
...
11.0
12.0
13.0
13.5
14.5
15.5
15.5
16.0
16.5
17.5
19.0
23.0
26.0
16
30
53
77
110
172
222
311
364
531
655
865
1447
2435
2955
4080
Weights
MJxFE*
...
...
48
60
107
168
215
...
360
430
543
1099
...
...
...
...
MJxPE
...
...
45
69
111
167
218
...
360
455
664
825
1510
1930
...
...
22 Bends (1/16)
22 MJ (1/16)
22 MJ x PE (1/16)
22 MJ x FE (1/16)
Size
Dimensions
Y
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
7.56
10.06
15.06
17.62
22.62
27.62
25.12
27.62
30.19
35.19
37.69
57.81
72.88
88.00
103.06
3.0
4.0
5.0
5.5
6.5
7.5
7.5
8.0
8.5
9.5
11.0
15.0
18.0
21.0
24.0
MJ
Weights
MJxFE*
11.0
12.0
13.0
13.5
14.5
15.5
15.5
16.0
16.5
17.5
19.0
23.0
26.0
30
52
77
110
156
221
300
391
527
611
986
1898
2372
3020
4170
...
...
71
107
155
215
...
315
422
...
800
...
...
...
...
MJxPE
...
...
70
109
163
224
...
365
455
575
930
1540
1970
...
...
11 Bends (1/32)
11 MJ (1/32)
11 MJ x PE (1/32)
11 MJ x FE (1/32)
256772_utility catalog.pdf 15
Size
Dimensions
Y
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
15.25
20.31
30.50
35.50
45.69
55.81
50.75
55.81
60.94
71.06
76.12
116.75
147.25
177.69
208.12
3.0
4.0
5.0
5.5
6.5
7.5
7.5
8.0
8.5
9.5
11.0
15.0
18.0
21.0
24.0
MJ
Weights
MJxFE*
11.0
12.0
13.0
13.5
14.5
15.5
15.5
16.0
16.5
17.5
19.0
23.0
26.0
30
52
65
104
171
221
305
391
525
605
996
1410
2397
3035
4190
...
...
71
105
...
215
...
367
422
...
800
...
...
...
...
MJxPE
...
...
...
...
...
...
...
...
...
...
972
1305
2185
...
...
12/15/08 8:24:22 AM
MJ TAPPED TEE
TEES
Bullhead
MJxMJxFE
Size
Dimensions
L
Max. Tap
3
4
6
8
10
12
8
8
8
8
8
8
2
2
2
2
2
2
Run
Size
Run
Branch
*2
*3
3
*4
4
4
4
*6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
14
14
*16
16
16
16
16
2
3
3
4
4
4
4
6
6
6
6
6
8
8
8
8
10
10
10
10
12
12
12
12
12
14
14
16
16
16
16
16
2
2
3
2
3
4
6
2
3
4
6
8
3
4
6
8
4
6
8
10
4
6
8
10
12
12
14
4
6
8
10
12
16
16
16
Weights
40
51
73
104
130
180
Dimensions
Y
MJ
Weights
**MJxPExMJ **MJxMJxFE
3.25
3.25
5.5
4.8
6.5
6.5
8.0
8.0
8.0
8.0
8.0
9.0
9.0
9.0
9.0
9.0
11.0
11.0
11.0
11.0
12.0
12.0
12.0
12.0
12.0
14.0
14.0
15.0
15.0
15.0
15.0
15.0
3.25
3.25
5.5
4.8
6.5
6.5
8.0
8.0
8.0
8.0
8.0
9.0
9.0
9.0
9.0
9.0
11.0
11.0
11.0
11.0
12.0
12.0
12.0
12.0
12.0
14.0
14.0
15.0
15.0
15.0
15.0
15.0
...
...
13.5
14.5
14.5
14.5
...
...
16.0
16.0
16.0
...
17.0
17.0
17.0
17.0
19.0
19.0
19.0
19.0
20.0
20.0
20.0
20.0
20.0
22.0
22.0
23.0
23.0
23.0
23.0
23.0
21
45
58
68
77
78
112
78
112
110
119
158
155
157
175
199
...
258
268
300
318
325
335
392
396
540
585
600
615
625
645
660
...
...
...
...
...
75
...
...
...
...
120
...
...
...
170
180
...
...
...
250
315
325
335
390
396
560
570
580
590
605
620
640
...
...
...
49
...
76
...
...
...
109
141
...
...
150
182
194
229
264
245
...
323
335
372
...
476
...
...
575
605
615
...
651
15.0
15.0
23.0
740
720
730
NOTICE: Weights published in this catalog are for shipping purposes only. Actual weights may vary
because some fittings are produced in
foundries. All fittings meet the AWWA
standards to which they are designed.
For weights of specific fittings, please contact Tyler
Company.
256772_utility catalog.pdf 16
12/15/08 8:24:22 AM
TEES (Con't)
Bullhead
MJxMJxFE
Run
Size
Run
18
18
18
18
20
20
20
20
20
24
24
24
24
24
24
24
24
30
30
30
30
30
30
30
30
30
36
36
36
36
36
36
36
36
36
36
36
42
42
42
42
48
48
48
48
48
18
18
18
18
20
20
20
20
20
24
24
24
24
24
24
24
24
30
30
30
30
30
30
30
30
30
36
36
36
36
36
36
36
36
36
36
36
42
42
42
42
48
48
48
48
48
Branch
6
8
12
18
6
8
12
16
20
6
8
12
14
16
18
20
24
6
8
10
12
16
18
20
24
30
6
8
10
12
14
16
18
20
24
30
36
24
30
36
42
24
30
36
42
48
13.0
13.0
13.0
16.5
14.0
14.0
14.0
18.0
18.0
15.0
15.0
15.0
15.0
15.0
22.0
22.0
22.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
25.0
25.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
28.0
28.0
23.0
31.0
31.0
31.0
26.0
26.0
34.0
34.0
34.0
Dimensions
Y
15.5
15.5
15.5
16.5
17.0
17.0
17.0
18.0
18.0
19.0
19.0
19.0
19.0
19.0
22.0
22.0
22.0
23.0
23.0
23.0
23.0
23.0
23.0
23.0
25.0
25.0
26.0
26.0
26.0
26.0
26.0
26.0
26.0
26.0
26.0
28.0
28.0
30.0
31.0
31.0
31.0
34.0
34.0
34.0
34.0
34.0
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
MJ
710
674
749
945
849
892
896
1095
1258
1233
1234
1256
1220
1245
1735
1720
1947
2050
2060
2075
2090
2145
2170
2205
2880
2275
2439
2444
2535
2541
2570
2585
2610
2635
2792
3545
3450
3690
4650
4880
6320
4995
5140
6280
8130
8420
Weights
**MJxPExMJ **MJxMJxFE
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
....
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
707
675
733
953
...
859
...
...
1168
1228
1242
1165
...
...
...
...
1795
...
...
...
...
...
...
...
...
3080
2430
...
...
2550
...
2450
...
...
2660
...
...
...
...
...
...
...
...
...
...
...
256772_utility catalog.pdf 17
17
12/15/08 8:24:22 AM
CROSSES
WYES/LATERAL
( Not included in AWWA C110.)
*NOTE:"X" & "Z" dimensions are approximate, contact
Tyler Union for specific fitting laying lengths
*MJ x MJ x FE x FE
ALL MJ
Size
Run Branch
3
4
6
6
8
8
8
10
10
10
12
12
14
16
18
18
18
18
18
20
20
20
20
24
30
36
36
42
42
3
4
4
6
4
6
8
6
8
10
8
12
6
16
8
10
12
16
18
10
12
16
20
24
30
24
36
24
30
Dimensions
X
Z
10.0
12.0
14.5
14.5
17.5
17.5
17.5
20.5
20.5
20.5
24.5
24.5
27.0
30.0
32.0
32.0
32.0
32.0
32.0
35.0
35.0
35.0
35.0
40.5
49.0
54.0
60.0
60.0
63.0
3.0
3.0
3.5
3.5
4.5
4.5
4.5
5.0
5.0
5.5
5.5
5.5
6.0
6.5
7.0
7.0
7.0
7.0
7.0
8.0
8.0
8.0
8.0
9.0
10.0
15.0
19.5
12.0
12.0
Weights
60
90
130
145
190
205
230
330
310
435
505
490
626
1079
1073
975
1015
1135
1130
1220
1260
1375
1525
2372
3670
5390
6335
6810
7210
36
42
48
66.0
71.0
77.0
12.0
15.0
16.0
8355
9900
13150
Size
Run Branch
Dimensions
X
Y
MJ
Weights
*MJxFE
6
8
8
8
10
10
10
12
12
12
14
14
16
16
16
18
18
18
18
20
20
20
20
24
24
24
24
24
30
30
30
30
36
36
42
48
6
4
6
8
6
8
10
6
8
12
8
14
6
8
16
8
10
12
18
8
12
16
20
8
12
16
20
24
6
12
24
30
24
36
42
24
8.0
9.0
9.0
9.0
11.0
11.0
11.0
12.0
12.0
12.0
14.0
14.0
15.0
15.0
15.0
13.0
13.0
13.0
16.5
14.0
14.0
18.0
18.0
15.0
15.0
15.0
22.0
22.0
18.0
18.0
25.0
25.0
20.0
28.0
31.0
26.0
8.0
9.0
9.0
9.0
11.0
11.0
11.0
12.0
12.0
12.0
14.0
14.0
15.0
15.0
15.0
15.5
15.5
15.5
16.5
17.0
17.0
18.0
18.0
19.0
19.0
19.0
22.0
22.0
23.0
23.0
25.0
25.0
26.0
28.0
31.0
34.0
160
185
205
255
285
310
380
361
371
486
550
779
650
675
895
775
760
860
1140
951
977
1245
1440
1244
1326
1479
1965
2192
2085
2165
3180
3640
2910
4370
7145
5210
141
....
182
245
....
....
360
367
373
487
....
....
....
655
875
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
....
48
48
36
48
34.0
34.0
34.0
34.0
6790
9380
....
....
18
REDUCERS
* 3x2
* 4x2
4x3
* 6x2
6x3
6x4
MJ Reducer
8x3
8x4
8x6
10x6
10x8
12x4
12x6
12x8
MJ Small End Bell Reducer 12x10
14x6
14x8
14x12
16x6
16x8
16x10
16x12
16x14
MJ Large End Bell Reducer 18x8
18x10
18x12
18x14
18x16
20x10
20x12
20x16
20x18
24x12
Plain End-Plain End Reducer
24x16
24x18
24x20
*30x16
30x18
30x20
30x24
36x20
36x24
FExMJ Reducer
36x30
42x24
42x30
42x36
48x30
48x36
48x42
Weights
6
14
7
15
7
15
9
17
9
17
9
17
11
19
11
19
11
19
12
20
12
20
14
22
14
22
14
22
14
22
16 24
16
24
16
24
18
26
18
26
18
26
18
26
18
26
19
27
19
27
19
27
19
27
19
27
20
28
20
28
20
28
20
28
24
32
24
32
24
32
24
32
30
38
30
38
30
38
30
38
36
44
36
44
36
44
42
50
42
50
42
50
48
56
48
56
48
56
14
...
15
...
15
23
17
...
17
25
17
25
19
27
19
27
19
27
20
28
20
28
22
30
22
30
22
30
22
30
24
32
24
32
24 32
26
34
26
34
26
34
26
34
26
34
27
35
27
35
27
35
27
35
27
35
28
36
28
36
28
36
28
36
32
40
32
40
32
40
32
40
38
46
38
46
38
46
38
46
44
52
44
52
44
52
50
58
50
58
50
58
56
64
56
64
56
64
...
...
24
24
24
...
...
...
...
31
30
31
...
...
7
7
37
38
37
34
34
...
...
46
43
47
...
...
...
9
55
50
55
...
...
9
9
56
60
59
57
53
...
...
84
77
70
...
...
11
11
84
82
84
...
73
11
11
94
90
93
96
84
12
12
115 116
117
...
100
12
12 142 135 130 135 130
...
...
139 131
...
...
...
14
12
148 150
153
... 145
14
12 173 168 165 168 170
14
12 194 190 178 185 188
...
16
...
...
...
...
...
...
16
...
...
...
...
...
...
16
...
...
...
...
...
...
...
250
...
...
...
...
...
...
288 248
...
...
...
...
...
300
...
...
...
...
18
18
330 304
325
...
305
...
...
370
...
...
...
...
...
19
320
...
...
...
...
...
...
388
...
...
...
...
...
19
380 355
...
...
...
...
...
450
...
...
...
...
...
19
476
...
...
...
...
...
... 410
...
...
...
...
...
...
515 420
...
...
...
...
20
578 525
510
...
...
...
...
575
...
...
...
...
...
24
610 570
...
...
...
...
...
705 665
753
...
...
...
...
789 720
...
...
...
...
...
815 775
804
...
...
...
... 1150 1040
...
1015
...
...
... 1160 1050
...
1025
...
...
...
1225 1120
... 1090
...
...
... 1360 1255 1320 1215
...
...
... 1495
... 1466
...
...
...
... 1580
...
1535 1389
...
...
... 1919 1721
... 1585
...
...
... 2060
...
...
...
...
...
... 2370
...
...
...
...
...
... 2695
...
...
...
...
...
... 3005
...
...
... ...
...
... 3370
...
...
... ...
...
...
3750
...
...
... ...
MJxFE Reducer
...
...
35
...
50
62
...
75
80
105
130
...
130
175
190
195
215
270
...
...
...
325
...
300
...
405
...
445
...
...
510
...
455
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
SOLID SLEEVES
Size
*2
3
4
6
8
10
12
16
18
20
24
30
36
42
48
Standard
Pipe
O.D.
Short
L
Weight
2.50
3.96
4.80
6.90
9.05
11.10
13.20
17.40
19.50
21.60
25.80
32.00
38.30
44.50
50.80
8.0
7.5
7.5
7.5
7.5
7.5
7.5
9.5
9.5
9.5
9.5
15.0
15.0
15.0
15.0
13
25
35
45
65
85
120
206
246
275
360
745
1047
1312
1585
Size
Long
L
Weight
12
12
12
12
12
12
12
15
15
15
15
24
24
24
24
4
6
8
10
12
16
18
36
47
65
90
115
136
281
362
404
540
1085
1502
1550
1940
* Dual Purpose
Pipe
O.D.
Short
L
Weight
4.80/5.00
6.90/7.10
9.05/9.30
11.10/11.40
13.20/13.50
17.40/17.80
7.5
7.5
7.5
...
...
...
33
46
65
...
...
...
Long
L Weight
12
12
12
12
12
15
44
63
88
111
221
385
Size
4
6
8
10
12
ADAPTERS
Cutting-In
Sleeve & Gland
For Use
On Pipe O.D.
4.80
6.90
9.05
11.10
13.20
5.00
7.10
9.30
11.40
13.50
L 1
12
12
12
12
12
8
8
8
8
8
4.80
6.90
9.05
11.10
13.20
Weight
Gland Gland
Only & Sleeve
6.0
10.0
16.0
25.0
30.0
72
94
122
175
235
MJ x FE
Size
3
4
6
8
10
12
16
18
20
24
30
36
Dimensions
L
Weights
8
8
8
8
8
8
8
8
8
8
10
10
30
42
62
88
120
150
257
324
365
528
760
1070
256772_utility catalog.pdf 20
20
12/15/08 8:24:23 AM
PLUGS
CAPS
OFFSETS
Solid or Tapped
Solid or Tapped
Size
Tap
*2
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
2
2
2
2
2
2
2
2
2
2
2
2
2
2
...
...
Weight
Solid Tapped
5
9
13
15
45
66
79
120
147
192
220
338
660
838
1180
1455
5
9
14
15
45
66
79
120
147
190
219
338
660
838
...
...
Size
Tap
*2
3
4
6
8
10
12
16
18
20
24
30
36
42
48
2
2
2
2
2
2
2
2
2
2
2
2
2
..
..
Weight
Solid Tapped
6
10
18
34
46
58
86
178
215
250
370
680
850
1180
1595
...
10
13
30
45
54
80
175
215
249
370
680
850
...
...
MJ x PE
Size
Dimensions
L1
L
Weights
MJxMJ MJxPE
4
4
4
* 4
6
6
6
* 6
8
8
8
* 8
10
10
10
12
12
*12
16
16
*20
*20
6
12
18
24
6
12
18
24
6
12
18
24
12
18
24
12
18
24
12
18
12
18
19
22
30
26
20
26
33
24
21
28
35
36
30
38
38
37
48
48
40
50
40
48
...
85
105
126
114
148
188
182
177
231
287
280
347
340
420
420
520
649
715
850
1025
1362
MJ x MJ
27
30
38
34
28
34
41
32
29
36
43
44
38
46
46
45
56
56
48
58
48
60
82
80
...
125
105
143
176
160
155
195
282
285
280
340
...
420
520
630
...
830
...
...
TYTON Plug**
Solid or Tapped
Size
Tap
Weight*
4
6
8
10
12
2
2
2
2
2
.60
.65
.70
.75
.75
18
25
46
70
95
Solid
Tapped
Tap
Weight
14
16
18
20
24
2.0
2.0
2.0
2.0
2.0
101
137
177
239
311
256772_utility catalog.pdf 21
21
12/15/08 8:24:23 AM
3
4
6
8
10
12
14
16
18
20
24
Pressure
Rating,
psi
Gland
O.D.
B
350
350
350
250
250
150
250
200
200
200
150
7.69
9.12
11.12
13.37
15.62
17.88
20.25
22.50
24.75
27.00
31.50
3.96
4.80
6.90
9.05
11.10
13.20
15.30
17.40
19.50
21.60
25.80
50-56
50-56
50-56
50-56
50-56
50-56
53-56
53-56
53-56
53-56
53-56
No of
Set
Screws
4
4
6
9
12
16
20
24
24
28
32
Size of
Set
Screws
Gland Weight
Weight w/Acces.
x2
x2
x2
x2
x2
x2
x2
x2
x2
x3
x3
4
5
9
13
17
20
44
54
62
76
103
8
11
16
21
26
28
55
64
72
91
118
TEES
MJ GLAND
MJ x MJ x Swivel
Size
6
8x6
8
10x6
12x6
16x6
16x8
30x6
Dimensions
X
Y
8.0
9.0
9.0
11.0
12.0
15.0
15.0
18.0
10.5
11.5
11.5
13.5
14.5
17.5
17.5
24.5
Weight
150
199
210
267
346
619
649
2070
Size
Gland
Weight
Wt. Pack Gland Only
5
7
10
16
25
30
40
45
55
65
85
105
220
301
Call
Call
256772_utility catalog.pdf 22
2
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
3
4
6
10
16
19
26
34
54
52
73
91
90
127
279
341
22
12/15/08 8:24:24 AM
Wall
Thickness
Weight*
.52
.55
.55
.55
.55
.60
.75
52
84
91
105
156
126
186
4x13
6x12
6x18
6x24
6x36
8x13
12x13
ELLS
*90 Swivel x Swivel Ell
(Not Included In AWWA C110)
Size
Wall
Thickness
6
8
.55
.60
Dimensions
C
D
E
*Weight
106
156
Swivel Glands**
Size
Weight
12
30
** Not included in
AWWA C110.
256772_utility catalog.pdf 23
12/15/08 8:24:24 AM
EXCEPTIONS: Union-Tite fittings with flanged branches are rated for water pressure of 250 PSI but can be rated for 350 PSI with the
use of an annular ring or comparable gasket. Wye fittings over 12" are not pressure rated, call Tyler Union for information.
4
6
8
10
12
14
16
18
20
24
TYTON
5.04
7.14
9.32
11.37
13.47
15.64
17.74
19.83
21.94
26.14
6.38
8.52
10.90
12.91
15.12
18.12
20.32
22.52
24.29
29.14
B.C.
7.88
10.50
12.88
14.69
17.19
19.00
21.40
...
...
...
4.16
4.29
4.78
4.98
4.98
5.40
5.40
5.40
5.40
5.65
2.25
2.25
2.25
2.25
2.25
2.25
2.25
2.25
2.25
2.50
.35
.37
.39
.41
.43
.51
.52
.59
.60
.62
For Joint deflection, refer to Tyler Union product submittal 26U located on page 65 of this catalog.
NOTE: The fitting laying lengths provided are approximate, contact Tyler Union Waterworks for the
laying length of a specific fitting.
1191CR 492 Tyler, Texas 75706 (800) 527-8478
24
BENDS
90(1/4) UT Bends
Size
4
6
8
10
12
14
16
18
20
24
Dimensions
A
R
.35
.37
.39
.41
.43
.51
.52
.59
.60
.62
4.5
6.0
7.0
9.0
10.0
12.0
13.0
15.5
17.0
17.0
24
51
80
121
151
254
328
482
340
674
90(1/4)
UT x Flange Bends
Size T
4
6
8
10
12
14
16
3.87
5.37
6.37
8.36
9.36
10.98
12.00
14.00
15.50
15.59
45 (1/8) UT Bends
Weight
.35
.37
.39
.41
.43
.51
.52
Dimensions
B
R
4.5
6.0
7.0
9.0
10.0
12.0
13.0
imensions
D
A
R
2.0
3.0
3.5
4.5
5.5
5.5
6.0
6.5
7.0
7.5
3.31
5.72
6.93
9.34
11.75
10.85
12.02
12.36
13.59
14.69
Weight
26
42
66
101
128
143
225
209
397
492
45 (1/8)
UT x Flange Bends
Weight
6.5 3.87 31
7.0 5.37 49
9.0 6.37 74
10.0 8.36 130
12.0 9.36 158
15.5 10.98 231
16.5 12.00 233
Dimensions
A
B
R
2.0
3.0
3.5
4.5
5.5
5.5
6.0
Weight
4.0 3.31 21
5.0 5.72 42
5.5 6.93 60
6.5 9.34 93
7.5 11.75 122
8.5 10.85 162
9.5 12.02 275
22 (1/16) UT Bends
imensions
D
A
R
1.50
2.25
2.50
3.00
3.50
3.75
4.00
7.50
8.50
9.00
4.38
8.16
9.40
13.17
14.42
13.82
14.97
30.19
35.19
37.69
Dimensions
A
R
18
39
64
67
111
162
195
209
414
596
1.25
1.50
1.75
2.00
2.25
2.60
2.60
3.00
3.50
...
22 (1/16)
UT x Flange Bends
Dimensions
A
B
R
1.50
2.25
2.50
3.00
3.50
3.75
4.00
3.5
4.3
4.5
5.3
5.5
6.8
7.5
4.38
8.16
9.40
13.17
14.42
13.82
14.97
Weight
6.77
9.38
11.48
13.95
16.50
14.26
15.23
60.94
71.07
...
18
40
60
77
94
113
172
209
265
...
11 (1/32)
UT x Flange Bends
Dimensions
B
R
Weight
25
44
64
90
112
174
228
1.25
1.50
1.75
2.00
2.25
2.60
2.60
NOTE: The fitting laying lengths provided are approximate, contact Tyler Union Waterworks for the
laying length of a specific fitting.
256772_utility catalog.pdf 25
11 (1/32) UT Bends
Weight
3.30
3.50
3.75
4.00
4.30
5.75
6.10
Weight
6.77
9.38
11.48
13.95
16.50
14.26
15.23
24
30
61
80
94
170
228
25
12/15/08 8:24:25 AM
BENDS
90(1/4)
UT x PE Bends
Size T
Weight
4
6
8
.35
.37
.39
45 (1/8)
UT x PE Bends
Dimensions
B
R
4.5 10.5
6.0 12.0
...
...
Weight
3.87 35
5.37 70
...
..
Dimensions
A
B
R
2.0
3.0
3.5
8.0
9.0
9.5
22 (1/16)
UT x PE Bends
Weight
3.31 21
5.72 38
6.93 60
Dimensions
A
B
R
Weight
...
...
...
..
2.25 8.08 8.16 35
2.50 8.34 9.40 57
11 (1/32)
UT x PE Bends
A
Dimensions
B
R
...
...
...
..
1.50 7.30 9.38 36
1.75 7.55 11.48 55
TEES
256772_utility catalog.pdf 26
UT x UT x PE Tees
Size
Run Branch
6
8
12
6
6
6
.37
.39
.43
Dimensions
T1
H
.37
.37
.37
6.0
6.0
7.0
J3
Weight
11.5
12.5
15.5
60
80
140
12/15/08 8:24:25 AM
TEES
UT x UT Tees
Size
4
6x4
6
8x4
8x6
8
10x4
10x6
10x8
10
12x4
12x6
12x8
12x10
12
14x6
14x10
14x12
14
16x6
16x8
16x10
16x12
16x14
16
18x6
18x8
18x10
18x14
18x16
20x6
20x10
20x14
20x16
20x18
24x6
24x10
24x12
24x14
24x16
24x18
24x20
24
T1
.35
.37
.37
.39
.39
.39
.41
.41
.41
.41
.43
.43
.43
.43
.43
.51
.51
.51
.51
.52
.52
.52
.52
.52
.52
.59
.59
.59
.59
.59
.60
.60
.60
.60
.60
.62
.62
.62
.62
.62
.62
.62
.62
.35
.35
.37
.35
.37
.39
.35
.37
.39
.41
.35
.37
.39
.41
.43
.44
.46
.47
.51
.45
.46
.47
.48
.51
.52
.44
.45
.47
.56
.57
.44
.47
.56
.57
.59
.44
.47
.49
.56
.57
.59
.60
.62
UT x Flange Tees
Dimensions
H
J1
4.5
5.0
6.0
5.0
6.0
7.0
6.0
7.0
8.0
9.0
6.0
7.0
8.0
9.0
10.0
6.5
8.5
9.5
10.5
6.5
7.5
8.5
9.5
10.5
11.5
6.5
7.5
8.5
10.5
11.5
7.0
9.0
11.0
12.0
13.0
7.0
9.0
10.0
11.0
12.0
13.0
15.0
17.0
4.5
6.0
6.0
7.0
7.0
7.0
9.0
9.0
9.0
9.0
10.0
10.0
10.0
10.0
10.0
10.5
10.5
10.5
10.5
11.5
11.5
11.5
11.5
11.5
11.5
12.5
12.5
12.5
12.5
12.5
14.0
14.0
14.0
14.0
14.0
16.0
16.0
16.0
16.0
16.0
16.0
17.0
17.0
UT x Swivel Tees
J2
J3
UT x UT
6.5
8.0
8.0
9.0
9.0
9.0
11.0
11.0
11.0
11.0
12.0
12.0
12.0
12.0
12.0
12.5
12.5
12.5
14.0
13.5
13.5
13.5
13.5
15.0
15.0
14.5
14.5
14.5
16.0
16.0
16.0
16.0
17.5
17.5
17.5
18.0
18.0
18.0
19.5
19.5
...
...
...
...
...
9.5
...
10.5
10.5
...
12.5
12.5
...
...
13.5
13.5
...
...
14.0
...
...
...
15.0
15.0
...
...
...
...
16.13
16.13
...
...
...
17.5
...
...
...
...
19.5
...
...
...
...
...
...
...
44
68
69
73
96
116
102
113
145
155
119
141
177
160
217
176
195
196
209
266
292
232
239
349
261
348
325
344
342
362
355
369
484
610
539
385
478
663
542
566
593
628
884
Weights
UT xFlange
45
56
71
89
101
117
115
128
145
158
138
148
170
162
183
212
246
296
321
160
270
330
321
342
355
301
319
337
393
420
341
420
474
498
...
512
468
503
531
555
...
...
...
UT x Swivel
...
...
65
...
100
110
...
130
156
...
...
162
158
...
...
202
...
...
...
229
292
...
...
...
...
348
324
...
...
...
400
...
...
...
...
525
...
...
...
...
...
...
NOTE: The fitting laying lengths provided are approximate, contact Tyler Union Waterworks for the laying length of a specific fitting.
256772_utility catalog.pdf 27
12/15/08 8:24:25 AM
UT x UT Reducers
Size
6x4
8x4
8x6
10x4
10x6
10x8
12x4
12x6
12x8
12x10
14x6
14x8
14x10
14x12
16x6
16x8
16x10
16x12
16x14
18x8
18x10
18x12
18x14
18x16
20x10
20x12
20x14
20x16
20x18
24x12
24x14
24x16
24x18
24x20
.37
.39
.39
.41
.41
.41
.43
.43
.43
.43
.51
.51
.51
.51
.52
.52
.52
.52
.52
.59
.59
.59
.59
.59
.60
.60
.60
.60
.60
.62
.62
.62
.62
.62
UT x Flange Reducers
Dimensions
T1
L
.35
.35
.37
.35
.37
.39
.35
.37
.39
.41
.44
.45
.46
.47
.45
.46
.47
.48
.51
.45
.47
.49
.56
.57
.47
.49
.56
.57
.59
.49
.56
.57
.59
.60
4.0
5.0
4.0
7.0
5.0
4.0
9.0
7.0
5.0
4.0
9.0
7.0
5.0
4.0
11.0
9.0
7.0
5.0
4.0
14.0
12.0
10.0
8.0
7.0
14.0
12.0
10.0
8.0
7.0
16.0
14.0
12.0
10.0
8.0
6.0
7.0
6.0
9.0
7.0
6.0
11.0
9.0
7.0
6.0
11.0
9.0
7.0
6.0
13.0
11.0
9.0
7.0
6.0
16.0
14.0
12.0
11.5
10.5
16.0
...
13.5
11.5
...
18.0
17.5
15.5
...
...
256772_utility catalog.pdf 28
32
46
49
47
47
53
74
58
74
82
84
85
87
104
94
104
130
152
139
142
151
167
217
202
180
205
233
250
248
246
281
380
390
421
32
46
47
55
59
61
78
75
74
95
121
128
127
144
133
141
158
172
196
157
175
215
234
246
234
...
249
272
...
262
315
328
...
...
4
6
8
10
12
14
16
20
Dimensions
T
L
.35
.37
.39
.41
.43
.51
.52
.60
6.0
6.0
6.0
6.0
6.0
7.0
7.0
6.0
Weight
28
36
54
71
102
113
115
295
UT x Tapped Tee/Crosses
Size
4
6
8
10
12
Dimensions
Max Tap
Weight
.35
.37
.39
.41
.43
3.0
3.5
3.5
3.5
3.5
6.0
6.0
6.0
6.0
6.0
27
38
59
72
92
UT x Flange Adaptor
Size
Weights
UT x UT UT xFlange
Solid Cap
Solid Plug
Size
Dimensions
T2
L
4
.48
.50
5.25
6
.48
.50
5.25
8
.51
.53
5.25
10
.53
.56
5.25
12
.55
.62
5.25
*Restraining lugs (ears) available.
Weights
Cap
Plug
15
20
35
50
75
8
23
32
38
49
NOTE: The fitting laying lengths provided are approximate, contact Tyler Union Waterworks
for the laying length of a specific fitting.
28
12/15/08 8:24:26 AM
WYES
CROSSES
UT Wyes
Size
8x4
10x4
10x6
10x8
10
12x4
12x6
12x8
12x10
12
14x6
14x8
14x10
14
16x6
16x8
16x12
16
.39
.41
.41
.41
.41
.43
.43
.43
.43
.43
.51
.51
.51
.51
.52
.52
.52
.52
Dimensions
T1
P
Weights
.35
.35
.37
.39
.41
.35
.37
.39
.41
.43
.44
.45
.46
.51
.45
.46
.48
.52
0.0
0.0
1.0
2.5
4.0
0.0
1.5
1.5
3.0
5.0
0.0
1.5
3.0
6.0
0.0
0.5
3.5
6.5
89
141
151
175
200
178
201
224
240
289
236
255
325
475
281
304
346
380
13.5
15.0
16.0
17.0
18.0
16.5
18.5
18.5
20.0
20.0
19.5
21.0
22.5
25.0
21.0
22.5
25.0
28.0
UT Crosses
Size
T1
Dimensions
H
Weights
.37
.37
.39
.35
.39
.43
.44
.45
.46
.47
.51
.45
.46
.47
.48
.51
.52
6.0
6.0
7.0
6.0
8.0
10.0
6.5
7.5
8.5
9.5
10.5
6.5
7.5
8.5
9.5
10.5
11.5
6.0
7.0
7.0
9.0
10.0
10.0
10.5
10.5
10.5
10.5
10.5
11.5
11.5
11.5
11.5
11.5
11.5
88
117
156
116
240
241
189
204
222
239
270
234
323
268
274
322
317
6
8x6
8
10x4
12x8
12
14x6
14x8
14x10
14x12
14
16x6
16x8
16x10
16x12
16x14
16
TYTON GASKETS
4
6
8
10
12
5.74
7.86
10.15
12.10
14.31
4.18
6.31
8.32
10.30
12.70
4.68
6.73
8.85
10.87
12.95
1.00
1.10
1.29
1.36
1.45
256772_utility catalog.pdf 29
NOTE: The fitting laying lengths provided are approximate, contact Tyler Union Waterworks for the laying length of a specific fitting.
12/15/08 8:24:26 AM
FLANGE DETAILS
Nominal
Pipe Size
Inch
2
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
Flange
O.D.
6
7.5
9
11
13.5
16
19
21
23.5
25
27.5
32
38.75
46
53
59.50
Dia. of
Bolt
Circle
4.75
6
7.5
9.5
11.75
14.25
17
18.75
21.25
22.75
25
29.5
36
42.75
49.50
56.00
Flange
Thickness
T
.62
.75
.94
1.00
1.12
1.19
1.25
1.38
1.44
1.56
1.69
1.88
2.12
2.38
2.62
2.75
Bolt Hole
Diameter
.75
.75
.75
.875
.875
1.00
1.00
1.125
1.125
1.25
1.25
1.375
1.375
1.675
1.625
1.625
Number
of Bolts
Bolt Dia.
and Lengths
4
4
8
8
8
12
12
12
16
16
20
20
28
32
36
44
x 2
x 2
x 3
x 3
x 3
x 4
x 4
1 x 4
1 x 4
1 x 5
1 x 5
1 x 5
1 x 6
1x7
1x7
1x8
NOTE: Drilling templates are in multiples of four, so that fittings may be made to face in any
quarter. Bolt holes shall straddle the center line.
256772_utility catalog.pdf 30
30
12/15/08 8:24:26 AM
BENDS
Note: Base Bends are on page 33 and 34, reducing and long radius 90 bends are on page 33.
90Bends (1/4)
Size
2
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
Dimensions
R
A
Weight
3.0
4
4.5
6
7
9
10
11.5
12.5
14
15.5
18.5
21.5
24.5
27.5
30.5
256772_utility catalog.pdf 31
4.5
5.5
6.5
8
9
11
12
14
15
16.5
18
22
25
28
31
34
14
26
44
67
115
164
236
330
478
527
878
1085
1755
2135
3055
4095
45 Bends (1/8)
Dimensions
R
A
...
3.62
4.81
7.25
8.44
10.88
13.25
12.06
13.25
14.5
16.88
18.12
27.75
35.00
42.25
49.50
Weight
...
...
3
20
4
36
5
57
5.5
105
6.5
131
7.5
196
7.5
245
8
315
8.5
422
9.5
485
11
730
15 1355
18 1755
21 2600
24 3580
...
7.56
10.06
15.06
17.62
22.62
27.67
25.12
27.62
30.19
35.19
37.69
57.81
72.88
88.00
103.06
...
3
4
5
5.5
6.5
7.5
7.5
8
8.5
9.5
11
15
18
21
24
Weight
...
22
35
64
90
130
194
250
315
402
505
528
1385
1790
2665
3665
...
15.25
20.31
30.5
35.5
45.69
55.81
50.75
55.81
60.94
71.06
76.12
116.75
147.25
177.69
208.12
...
3
4
5
5.5
6.5
7.5
7.5
8
8.5
9.5
11
15
18
21
24
Weight
...
20
40
56
90
130
193
245
315
385
505
760
1395
1805
2680
3695
31
12/15/08 8:24:26 AM
Run
Size
Run
2
3
3
4
*4
4
4
*4
*6
*6
*6
6
6
6
6
*8
*8
*8
8
8
8
8
*8
*8
*10
*10
*10
*10
*10
10
10
10
10
10
* 12
*12
*12
2
3
3
3
4
4
4
4
4
4
6
6
6
6
6
6
6
6
8
8
8
8
8
8
6
6
8
8
8
10
10
10
10
10
6
6
8
256772_utility catalog.pdf 32
Branch
2
2
3
3
2
3
4
6
4
6
2
3
4
6
8
4
6
8
3
4
6
8
10
12
6
10
6
8
10
4
6
8
10
12
6
8
6
*Reducing
on Run
Dimensions
H
J
4.5
5.5
5.5
6.5
6.5
6.5
6.5
8.0
8.0
8.0
8.0
8.0
8.0
8.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
11.0
12.0
13.0
13.0
13.0
13.0
13.0
11.0
11.0
11.0
11.0
12.0
14.0
14.0
14.0
4.5
5.5
5.5
5.5
6.5
6.5
6.5
8.0
8.0
8.0
8.0
8.0
8.0
8.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
11.0
12.0
13.0
13.0
13.0
13.0
13.0
11.0
11.0
11.0
11.0
12.0
14.0
14.0
14.0
*Reducing on
Run and Branch
Weights
Tee
Cross
20
35
42
53
55
54
60
88
96
100
85
85
90
98
138
130
148
154
128
155
148
179
225
277
278
308
298
278
325
239
215
254
265
337
346
362
355
...
51
...
...
76
87
...
...
...
...
96
112
141
...
...
...
...
140
155
172
195
...
...
...
...
...
...
...
220
242
294
330
...
...
...
...
*Bullhead
Tees
Run
Size
Run
*12
*12
*12
12
12
12
12
12
12
12
12
*14
14
14
14
14
14
*16
16
16
16
16
16
16
18
18
18
18
18
18
18
8
8
10
10
10
10
12
12
12
12
12
14
14
14
14
14
14
16
16
16
16
16
16
16
18
18
18
18
18
18
18
Branch
8
12
6
8
10
12
4
6
8
10
12
4
6
8
10
12
14
4
6
8
10
12
14
16
6
8
10
12
14
16
18
Straight and
Reducing Crosses
Dimensions
H
J
12.0
12.0
14.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
14.0
14.0
14.0
14.0
14.0
14.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
13.0
13.0
13.0
13.0
16.5
16.5
16.5
12.0
12.0
14.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
12.0
14.0
14.0
14.0
14.0
14.0
14.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.5
15.5
15.5
15.5
16.5
16.5
16.5
Weights
Tee
Cross
375
420
390
400
420
440
322
297
346
394
369
410
420
435
450
470
500
525
573
555
565
590
610
635
780
609
585
638
808
760
865
...
...
...
...
...
...
310
326
351
415
438
...
450
475
...
555
595
...
565
590
620
665
...
755
...
...
...
706
...
...
915
32
12/15/08 8:24:27 AM
Size
Run
20
20
20
20
20
20
20
20
24
24
24
24
24
24
24
24
24
*30
30
30
30
30
36
36
36
42
42
42
42
48
48
48
48
48
20
20
20
20
20
20
20
20
24
24
24
24
24
24
24
24
24
30
30
30
30
30
36
36
36
42
42
42
42
48
48
48
48
48
Branch
6
8
10
12
14
16
18
20
6
8
10
12
14
16
18
20
24
6
12
18
24
30
24
30
36
24
30
36
42
24
30
36
42
48
Dimensions
H
J
14.0
14.0
14.0
14.0
14.0
18.0
18.0
18.0
15.0
15.0
15.0
15.0
15.0
15.0
22.0
22.0
22.0
18.0
18.0
18.0
25.0
25.0
20.0
28.0
28.0
23.0
31.0
31.0
31.0
26.0
26.0
34.0
34.0
34.0
17.0
17.0
17.0
17.0
17.0
18.0
18.0
18.0
19.0
19.0
19.0
19.0
19.0
19.0
22.0
22.0
22.0
23.0
23.0
23.0
25.0
25.0
26.0
28.0
28.0
30.0
31.0
31.0
31.0
34.0
34.0
34.0
34.0
34.0
Tee
773
720
735
816
770
950
965
1005
1089
1060
1020
1125
1050
1070
1534
1510
1685
1725
1801
1852
2475
2615
2255
3000
3160
3245
4125
5360
5580
4385
4455
5555
7195
7385
Weights
Cross
...
...
...
820
...
1065
...
1175
...
...
...
1100
1125
1160
...
1695
1850
...
...
...
2695
2985
...
...
6740
...
...
...
...
...
...
...
...
...
*NOTE:"D", "H", "J", "X", "Y" and "L" dimensions are approximate,
contact Tyler Union for diameter or laying length of a
specific fitting.
256772_utility catalog.pdf 33
3
4
6
8
10
12
14
16
18
20
24
30
36
Dimensions
D
X
Y
7.5
9.0
11.0
13.5
16.0
19.0
21.0
23.5
25.0
27.5
32.0
38.8
48.0
5.5
6.5
8.0
9.0
11.0
12.0
14.0
15.0
16.5
18.0
22.0
25.0
28.0
8.5
9.5
12.0
13.0
15.0
16.0
22.0
23.0
24.5
26.0
30.0
38.0
38.0
Weight
26
39
73
110
171
253
450
545
675
860
1195
2070
2900
Dimensions
D L Weight
3 7.25 8
21
4 9.00 8
30
6 11.00 8
44
8 13.50 10
75
10 16.00 10 113
12 19.00 12 155
14 21.00 16 225
16 23.50 16 330
18 25.00 16 355
20 27.50 18 465
24 32.00 18 598
30 38.75 24
900
36 46.00 24 1200
*Flange by Flare not included
in AWWA C110
33
12/15/08 8:24:27 AM
REDUCERS
Concentric Reducer
*Eccentric Reducer
Size
Dimensions Wts
D
D1
L
Size
Dimensions Wts
D
D1
L
Size
Dimensions Wts
D
D1
L
3
4
4
6
6
6
6
8
8
8
8
10
10
10
12
12
12
12
14
14
14
14
16
16
16
16
16
18
18
18
18
18
20
20
20
20
20
24
24
24
24
24
30
30
30
30
42
42
42
48
48
48
4
3
7
30
18
6
3
9
45
18
6
4
9
52
20
8
4
11
70
20
8
6
11
80
20
20
20
24
24
24
24
24
30
30
30
30
36
36
42
42
42
48
48
48
2
2
3
2
3
4
5
3
4
5
6
4
6
8
4
6
8
10
6
8
10
12
6
8
10
12
14
6
7
7
9
9
9
9
11
11
11
11
12
12
12
14
14
14
14
16
16
16
16
18
18
18
18
18
17
23
29
30
44
46
56
61
63
70
75
98
107
116
119
130
152
178
165
185
205
235
210
230
255
285
315
8
10
12
14
16
10
12
14
16
18
12
14
16
18
20
16
18
20
24
24
30
36
30
36
42
19
19
19
19
19
20
20
20
20
20
24
24
24
24
24
30
30
30
30
42
42
42
48
48
48
265
290
320
350
405
418
465
430
445
470
608
565
610
645
695
945
970
1144
1155
1810
2060
2345
2615
2940
3320
Size
Dimensions Wts
D
D1
L
14
16
10
12
14
16
18
12
14
16
18
20
16
18
20
24
24
30
24
30
36
30
36
42
19
19
20
20
20
20
20
24
24
24
24
24
30
30
30
30
36
36
42
42
42
48
48
48
350
385
350
370
402
449
455
535
570
614
645
695
778
810
870
970
1425
2120
2340
2060
2345
2625
2950
3320
NOTE: Eccentric
Reducers not included in
AWWA C110
34
* WYES/LATERALS
*45 Wye
Size
Run Branch
3
4
4
6
6
8
8
8
10
10
10
10
12
12
12
12
12
14
14
14
14
14
16
16
16
16
16
16
18
18
18
18
18
18
20
20
20
20
20
24
36
3
3
4
4
6
4
6
8
4
6
8
10
4
6
8
10
12
6
8
10
12
14
6
8
10
12
14
16
8
10
12
14
16
18
10
12
14
16
20
24
36
Dimensions
H J
Weight
10
3
49
12
3
68
12
3
76
14.5
3.5 106
14.5
3.5 131
17.5
4.5 153
17.5
4.5 188
17.5
4.5 201
20.5
5
232
20.5
5
288
20.5
5
333
20.5
5
300
24.5
5.5 355
24.5
5.5 370
24.5
5.5 395
24.5
5.5 420
24.5
5.5 460
27
6
500
27
6
525
27
6
555
27
6
600
27
6
640
30
6.5 655
30
6.5 680
30
6.5 715
30
6.5 755
30
6.5 800
30
6.5 850
32
7
820
32
7
855
32
7 1003
32
7
940
32
7
990
32
7 1035
35
8 1095
35
8 1130
35
8 1170
35
8 1220
35
8 1345
40.5
9 2020
60
19.5 5740
*90 Reducing
Bend (1/4)
*True Wye
Size
Dimensions
Stem Branch X
Y Weight
4
6
6
8
8
10
10
10
12
12
12
16
4
4
6
6
8
6
8
10
8
10
12
16
6.5
8.0
8.0
9.0
9.0
8.0
9.0
11.0
9.0
11.0
12.0
15.0
3.0
3.5
3.5
4.5
4.5
5.0
5.0
5.0
5.5
5.5
5.5
6.5
49
75
84
134
125
140
155
220
210
240
315
520
Dimensions
Size
A
Weight
Size
4x3
6.5
6x4
8.0
8x4
9.0
8x6
9.0
10x6 11.0
10x8 10.0
12x6 12.0
12x8 12.0
12x10 12.0
14x6 14.0
14x8 14.0
35
65
88
96
126
151
172
191
218
230
240
3
6.25
4
7
6
9.5
8 14
10 16.5
12 17
14 19
16 21.5
18
.....
20 .....
24 .....
* Not included in
*BASE BENDS
Base Bends
are made
to order
only, not
returnable.
Bases are
furnished
faced and
drilled.
3
4
6
8
10
12
14
16
18
20
24
30
36
Support
Dimensions
Pipe
X
S
U
Size
4.88
5.50
7.00
8.38
9.75
11.25
12.50
13.75
15.00
16.00
18.50
23.00
26.00
7.75
32
9
46
11.5
83
14
140
16.5 252
19
310
21.5 475
24
630
26.5
840
29
1080
34
1640
BASE TEES
Dimensions
A
Weight
5
6
7
9
9
11
11
11
13.5
13.5
13.5
16
19
.50
.50
.62
.88
.88
1.00
1.00
1.00
1.12
1.12
1.12
1.15
1.15
1.5
2.0
2.5
4.0
4.0
6.0
6.0
6.0
8.0
8.0
8.0
10.0
10.0
Base Tees
90
Weight
90LR
Tee
38
50
83
142
210
300
400
505
645
805
1215
1945
2395
41
60
100
180
315
427
580
740
...
...
...
...
2895
47
76
115
195
315
450
570
710
900
1125
1927
...
...
*NOTE: "A", "H", "J", "X", & "Y" dimensions are approximate, contact Tyler Union for laying length or base height of a specific fitting
256772_utility catalog.pdf 35
35
12/15/08 8:24:27 AM
* FLANGE SLUDGE
SHOE
Base Under
Large End
Size
Base Under
Small End
Dimensions
X
S
4x3
5.5
6x4
7
8x4
8.38
8x6
8.38
10x6
9.75
10x8
9.75
12x6
11.25
12x8
11.25
12x10 11.25
6
7
9
9
9
9
11
11
11
Weight
.50
.62
.88
.88
.88
.88
1.00
1.00
1.00
45
75
118
135
175
184
230
255
285
Nom.
Diameter
Inches
Weight
3 5.75 12
6
28
4 7.00 12
6
35
6 7.87 12
6
45
8 10.12 12
6
69
10 12.25 12
6
88
12 15.25 12
6
120
* Not included in AWWA C110
Size
Dimensions
D
X
Y
Dimensions - Inches
Bolt Hole Number
BC
Diameter
of Bolts
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
3.88
4.75
5.50
7.50
7.50
9.50
9.50
9.50
11.75
11.75
11.75
14.25
17.00
21.25
22.75
5/8
3/4
3/4
3/4
3/4
7/8
7/8
7/8
7/8
7/8
7/8
1
1
1-1/8
1-1/4
Size
Dimensions
Y
Steel
DI
2
2
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
6
7
7.5
9
11
13.5
16
19
21
23.5
25
27.5
32
38.75
46.00
53.00
59.50
.62
.69
.75
.94
1.00
1.12
1.19
1.25
1.38
1.44
1.56
1.69
1.88
2.12
2.38
2.62
2.75
1
1.13
1.19
1.31
1.56
1.75
1.94
2.19
2.25
2.50
2.69
2.88
3.25
...
...
...
...
4.75
5.50
6.00
7.50
9.50
11.75
14.25
...
...
...
...
...
...
...
...
...
...
4
8
7
12
21
28
49
61
...
...
...
...
...
...
...
...
...
...
...
6
11
14
34
33
52
72
90
105
115
160
255
...
...
...
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
eight
W
Blind Blind Tap
...
...
8
15
28
45
62
72
110
165
192
249
375
580
790
1175
1585
...
...
8
15
28
45
62
87
110
165
190
250
370
580
...
...
...
DI Reducing Flange
Threaded For Steel Pipe
Size
4x3
6x4
8x4
8x6
10x6
12x6
10x8
12x10
DI Reducing Flange
Threaded For Cast Iron Pipe
Tap x O.D.
Weight
Size
Tap x O.D.
3x9
4x11
4x13
6x13
6x16
6x19
8x16
10x19
16
25
44
31
50
60
55
72
4x3
6x4
8x4
8x6
10x8
12x8
3x9
4x11
4x13
6x13
8x16
8x19
*NOTE: "X" and "Y" dimensions are approximate, contact Tyler Union for these dimensions of a specific fitting
256772_utility catalog.pdf 36
Weight
16
25
40
35
50
85
36
12/15/08 8:24:28 AM
ADAPTER FLANGES
(EZ OR UNI)
Size
Ductile Iron
Pipe OD
+.06 or -.06
3
4
6
8
10
12
3.96
4.80
6.90
9.05
11.10
13.20
D
+.06
-.04
4.94
6.02
8.12
10.27
12.34
14.44
F
+.07
-.03
Weight
4.06
4.90
7.00
9.15
11.20
13.30
.94
1.00
1.06
1.12
1.19
1.25
7
10
14
22
30
40
No. of
Set
Bolt
Screws Circle
3
4
6
8
10
12
4
4
8
8
12
12
250
250
250
250
250
150
6.00
7.50
9.50
11.75
14.25
17.00
No. of
Bolt &
Size
Nuts of Bolt
4
8
8
8
12
12
Bolt
Hole
Dia.
x2
x3
x3
x3
x4
x4
1
1
Fittings can be supplied with taps sized and located to ANSI B16.1
and MSS-SP-45. Specify fitting size, tap location by letter (refer to
drawings) and tap size by NPT dimension, on order.
Note:
Fitting
itting
F
Size
Size
Maximum
TapTap
Maximum
Without
Boss
Without
Boss
3"........................ 1/2"
4" - 6"................. 3/4"
8"........................ 1-1/4"
10" - 16"............... 1-1/2"
18" - 36"............... 2"
256772_utility catalog.pdf 37
37
12/15/08 8:24:28 AM
**6850 SERIES
CAST IRON TWO-PIECE VALVE BOXES
Box Assembled
(Less Lid)
Box (Components)
461-S
462-S
562-S
563-S
564-S
662-S
664-S
665-S
666-S
668-S
(10T + 15B)
19-22 145776
(10T + 24B)
27-32 145783
(16T + 24B)
27-37 145790
(16T + 30B)
33-43 145752
(16T + 36B)
39-50 145806
(26T + 30B)
36-52 145769
(26T + 36B)
39-60 145813
(26T + 24B)
39-63 375296
(26T+24B+60 Ext) 53-71 145820
(26T+36B+60 Ext) 64-82 145837
NOTE: D=Domestic
ND=Non-Domestic
502098 50
502104 58
502111 71
-----
78
502128 85
----
93
----
100
----
87
502135 128
----
136
*(ND-Std.)UPCode
670610
Wt
112280 35
112297 43
112303 50
112310 60
112327 66
112341 76
112358 82
---
--112365 95
112372 111
Std.=Standard Weight
39
6850 SERIES
CAST IRON TWO-PIECE VALVE BOXES
TOP
Length
Box
**(D-HD) UPCode
670610
Wt
144939
144939
144946
144946
144946
144953
144953
144953
144953
22
22
36
36
36
51
51
51
51
461-S (10T)
462-S (10T)
562-S (16T)
563-S (16T)
564-S (16T)
662-S (26T)
664-S (26T)
666-S (26T)
668-S (26T)
**NOTE: D=Domestic
ND=Non-Domestic
**(ND-HD) UPCode
670610
Wt
502142
502142
502159
502159
502159
502166
502166
502166
502166
**(ND-Std.) UPCode
670610
Wt
22
22
36
36
36
51
51
51
51
112402
112402
112419
112419
112419
112426
112426
112426
112426
15
15
22
22
22
38
38
38
38
Std.=Standard Weight
EXTENSIONS
Item/Description
#58 Screw-Type
#59 Screw-Type
#60 Screw-Type
14
18
24
145141
145158
145059
29
30
37
---
---
112389
----29
60 Extension
58 and 59 Extension
Bottom **(D-HD)UPCode
Length
670610
**(ND-HD)UPCode
**(ND-Std.)UPCode
Wt
670610
Wt
670610
Wt
461-S
462-S
562-S
563-S
564-S
662-S
664-S
666-S
668-S
(15B)
(24B)
(24B)
(30B)
(36B)
(30B)
(36B)
(24B)
(36B)
(48B)
(60B)
27
35
35
42
49
42
49
35
49
---
---
502173
502180
502180
502197
502203
502197
502203
502180
502203
---
---
27
35
35
42
49
42
49
35
49
---
---
112242
112259
112259
112266
112273
112266
112273
112259
112273
452737
452744
20
28
28
38
44
38
44
28
44
62
85
145004
145011
145011
144991
145028
144991
145028
145011
145028
---
---
**Note: D=Domestic
ND=Non-Domestic
Std.=Standard Weight
40
6855 SERIES
CAST IRON TWO-PIECE VALVE BOXES
Box Assembled
(Less Lid)
Box (Components)
461-A
462-A
562-A
563-A
564-A
662-A
664-A
666-A
668-A
(10T + 15B)
19-22 145844
(10T + 24B)
27-32 145831
(16T + 24B)
27-37 145868
(16T + 30B)
33-43 145714
(16T + 36B)
39-50 145875
(26T + 30B)
36-52 145721
(26T + 36B)
39-60 145882
(26T+24B+60 Ext) 53-71 145899
(26T+36B+60 Ext) 64-82 145905
NOTE: D=Domestic
ND=Non-Domestic
502234 55
----
65
502241 72
----
81
502258 83
----
97
502265 99
----
124
----
135
112099 34
112105 46
112112 55
112129 67
112136 72
112143 83
112150 88
112167 108
112181 125
Std=Standard Weight
41
6855 SERIES
CAST IRON TWO-PIECE VALVE BOXES
TOP
Length
**(D-HD) UPCode
670610
Wt
144960
144960
144977
144977
144977
144984
144984
144984
144984
29
29
36
36
36
52
52
52
52
461-A (10T)
462-A (10T)
562-A (16T)
563-A (16T)
564-A (16T)
662-A (26T)
664-A (26T)
666-A (26T)
668-A (26T)
**NOTE: D=Domestic
**(ND-HD) UPCode
670610
Wt
502272
502272
502289
502289
502289
502296
502296
502296
502296
ND=Non-Domestic
**(ND-Std.) UPCode
670610
29
29
36
36
36
52
52
52
52
112211
112211
112228
112228
112228
112235
112235
112235
112235
Std=Standard Weight
Wt
15
15
25
25
25
38
38
38
38
EXTENSIONS
Item/Description
#58-A Slip-Type 6 to 14
#59-A Slip-Type 6 to 18
#60-A Slip-Type 6 to 24
145233 29
145240 30
145066 36
136637
136644
112198
26
28
37
60-A Extension
**(ND-HD) UPCode
**(ND-Std.) UPCode
Wt
670610
Wt
670610
Wt
461-A
462-A
562-A
563-A
564-A
662-A
664-A
666-A
668-A
(15B)
(24B)
(24B)
(30B)
(36B)
(30B)
(36B)
(24B)
(36B)
(60B)
26
36
36
45
47
45
47
36
47
---
502302
502319
502319
502333
502340
502333
502340
*502319
*502240
---
26
36
36
45
47
45
47
36
47
---
112051
112068
112068
112075
112082
112075
112082
*112068
*112082
458302
20
30
30
39
43
39
43
30
43
75
145073
145080
145080
145127
145097
145127
145097
*145080
*145097
---
Std=Standard Weight
*NOTE: Whe installing thes extensions a 6850 screw type bottom is required
42
6860 SERIES
CAST IRON THREE-PIECE VALVE BOXES
Base Illustrated
For Position Only...
Not Furnished.
Box Assembled
(Less Lid)
Box (Components)
AA (10T + 12B)
A (16T + 18B)
B (16T + 24B)
C (16T + 30B)
CC (16T + 36B)
D (26T + 30B)
DD (26T + 36B)
E (16T+24B+60 Ext)
F (26T+24B+60 Ext)
G (26T+36B+60 Ext)
27-37
33-42
39-49
45-54
51-60
45-66
51-72
63-72
63-84
74-94
145912
145929
145936
145943
145950
145967
145974
145981
145998
146001
----
42
----
65
----
69
----
73
----
75
502357 88
502364 90
----
105
----
120
502371 126
*(ND-Std.)UPCode
670610
Wt
136668 29
136651 38
136675 51
136682 55
136699 59
136811 71
136828 75
136835 80
136842 96
136859 104
43
6860 SERIES
CAST IRON THREE-PIECE VALVE BOXES
TOP
Length
**(D-HD) UPCode
670610
Wt
AA
A
B
C
CC
D
DD
E
F
G
(10T)
(10T)
(16T)
(16T)
(16T)
(26T)
(26T)
(16T)
(26T)
(26T)
144939
144939
144946
144946
144946
144953
144953
144946
144953
144953
23
23
36
36
36
51
51
36
51
51
**(ND-HD) UPCode
670610
Wt
502142
502142
502159
502159
502159
502166
502166
502159
502166
502166
**(ND-Std.) UPCode
670610
Wt
15
15
22
22
22
38
38
22
38
38
**NOTE: D=Domestic ND=Non-Domestic HD=Heavy Duty Weight .=Standard Weight
60 Extension
58 and 59
Extension
23
23
36
36
36
52
52
36
52
52
#4 Base
112402
112402
112419
112419
112419
112426
112426
112419
112426
112426
#6 Base
(Standard)
UPC
670610
BASES
eight
Increase
Wt
Item/Description
14
18
24
24
24
29
30
37
29
36
#4, 11 Wide
#6, 14 Wide
#160, 20 Wide
#160 Base
EXTENSIONS
Item/Description
*(D-HD)UPCode *(ND)UPCode
670610
670610
145653
145660
145684
----
----
----
Wt
34
45
68
*(ND-Std)UPCode
670610
Wt
381532
381525
256861
**(ND-HD) UPCode
**(ND-Std.) UPCode
Wt
670610
Wt
670610
Wt
AA
A
B
C
CC
D
DD
E
F
G
(12B)
(18B)
(24B)
(30B)
(36B)
(30B)
(36B)
(24B)
(24B)
(36B)
(48B)
(60B)
19
29
33
37
39
37
39
33
33
39
---
---
---
505594
502388
502395
502401
502395
502401
502388
502388
502401
---
---
---
29
33
37
39
37
39
33
33
39
---
---
250524
250517
136958
136613
136620
136613
136620
136958
136958
136620
452713
452720
14
25
29
33
35
33
35
29
29
35
65
91
**NOTE: D=Domestic
145134
145141
145158
145165
145172
145165
145172
145158
145158
145172
---
---
ND=Non-Domestic
22
36
55
Std=Standard Weight
44
136880
12
*D=Domestic ND=Non-Domestic
HD=Heavy Duty Weight
Drop Lid
Lock Lid
*(D-HD)UPCode
670610
458892
136927
Wt.
**WATER OMA 12
WRENCH
Fits Standard Waterworks
Pentagon Head 27/32" Brass
Screws
UPCode
670610
144908
1 1/8" Lid
Ship
Code
Description
Wrench
Wt
0.5
LIDS (WATER)
*(D-HDUP)Code
Item/Description
670610
*(ND-Std)UPCode
Wt
670610
Wt
5 Drop Lid
5 Lock Lid
1 Lid**
12
11
11
145325
145462
145509
136910
136866
112532
9
11
9
*(ND-HD)UPCode
670610
Wt
---
---
---
-------
Special
670610
Wt.
Mark
145332
145349
145356
458975
12
12
12
12
670610 Wt.
136873
136903
136897
---
9
9
9
---
GAS
SEWER
PLAIN
REUSE
45
IRON RISERS
148197
112396
Height
Increase
Item/Description
Weight
2" - 9"
*(D-HD)UPCode. *(ND-HD)UPCode
Height
670610
670610
Increase
29
5 x 1 Slip-In*
5 x 2 Slip-In
145554
145547
112549
112556
Wt
1 "
2"
8
14
Specialty Iron Valve Box Tops - Call for Submittal / Product Drawing
*D-UPCode
376774
**ND-UPCode
502883
**ND-UPCode
502890
148241
112204
Height
Increase
2" - 12"
Wt
29
Description
Weight
Description
Weight
Description
Weight
49
37
Note: *D = Domestic
35
**ND = Non-Domestic
46
UPCode
670610
Ship
Code
148449
148456
148647
148494
148593
148500
148463
148470
148630
S
S
S
S
S
S
S
S
S
8
9
18
20
20
22
Description
Weight
39
39
27
13
14
13
41
41
29
*B/L = Large
Bolts (1-1/32"); *B/S = Small
Bolts (27/32" Standard)
NOTE: The B/L & B/S pentagon head screws use the same worm or locking gear.
Ship
Code
148531
148524
148579
148562
148586
148555
148548
S
S
S
S
S
S
S
Description
Weight
39
39
13
13
12
41
41
*B/L = Large Head Bolts (1-1/32"); B/S = Small Head Bolts (27/32")
NOTE: 6150TR - Same dimensions as 6150, plus a 1-27/32" access hole in lid.
NOTE: The B/L & B/S pentagon head screws use the same worm or locking gear.
Ship
Code
148708
148760
148739
148722
S
S
S
S
Description
Weight
28
18
13
11
WRENCH
Fits Standard Waterworks
Small Pentagon Head 27/32" Brass Screws
256772_utility catalog.pdf 47
UPCode
670610
Ship
Code
Description
Weight
144908
Wrench
0.5
47
12/15/08 8:24:30 AM
assembly instructions
ADAPTER FLANGE
Wall Thickness Note:
Recommended for ductile
iron pipe Class 53 thru
Class 56.
FM APPROVED
1. Place adapter flange and MJ gasket over the plain end of the
pipe with the small side of the MJ gasket facing the flange
side of the adapter flange.
2. Place the pipe end against flange to be joined and slip the
MJ gasket into position against the flange. Make sure the
gasket is evenly seated against the flange.
3. Slide adapter flange into position against the small (tapered) side of the MJ gasket and align the bolt holes.
Insert the bolts and finger tighten the nuts to maintain position and alignment.
4. Snug up all nuts evenly. Alternating @ 180, tighten the nuts to a torque of: 3" - 60 foot pounds; 4" thru 12"
- 90 foot pounds.
5. Snug up all set screws evenly around the pipe. Tighten the Torque Head Set Screws evenly, alternating at 180
degrees.
NOTE: THE TORQUE HEAD TOP WILL BREAK OFF AT THE RECOMMENDED SETTING OF 80-90 FT. LBS.
MAXIMUM DEFLECTION OF JOINT ( 2)
1. Wash bell and plain end with soapy water, then slip
gland and gasket over plain end with the small side of
the gasket and ring side of
gland facing the bell.
2. Slip plain end into bell. Brush soapy water on gasket.
This lubricates the gasket and allows it to slip easily
into place. Push gasket into bell making sure it is
evenly in the bell gasket landing.
3. Slide the gland into position against the back of the
gasket. Align bolt holes, insert T-bolts and tighten nuts
to finger tight.
4. Snug up all T-bolt nuts evenly. Alternating at 180,
tighten the T-bolt nuts to a torque of:
3" - 60 foot pounds 4" thru 24" - 90 foot pounds.
5. Snug up all set screws evenly. Using a torque wrench, tighten the set screws alternating at 180 to the
recommended torque value of 75 foot pounds. If required double check set screws immediately.
Maximum recommended deflection of joints:
3" thru 12"-2; 14" thru 30" - 1
*Note: Not recommended for use on plain end fittings
256772_utility catalog.pdf 50
48
12/15/08 8:24:31 AM
3
4
6
8
10
12
14
16
18
24
30
90
14.00
15.00
18.00
20.00
24.00
26.00
31.50
33.50
38.00
41.50
N/A
Nominal
Diameter
Inches
3
4
6
8
10
12
14
16
18
20
24
30
90
19.60
21.50
24.50
26.60
30.50
32.50
36.50
38.50
41.50
44.50
52.50
58.50
Nominal
Diameter
Inches
3
4
6
8
10
12
14
16
18
20
24
30
90
11.00
13.00
16.00
18.00
22.00
24.00
28.00
30.00
33.00
36.00
44.00
50.00
256772_utility catalog.pdf 51
153 -A21.53
C
Mechanical Joint
45
22
6.36
7.07
8.48
9.19
10.61
12.02
13.08
13.79
14.14
16.40
N/A
3.06
3.31
3.89
4.09
4.48
4.87
5.88
5.92
8.92
9.76
N/A
110 -A21.10
C
Mechanical Joint
45
22
10.25
11.69
13.06
13.76
15.19
16.62
16.62
17.32
18.03
19.45
21.57
27.23
5.56
6.31
7.08
7.50
8.25
9.00
8.99
9.38
9.76
10.52
11.67
14.73
C110 -A21.10
Standard Flange
45
22
4.24
5.66
7.07
7.78
9.19
10.61
10.61
11.31
12.02
13.44
15.56
21.22
2.30
3.06
3.83
4.21
4.98
5.74
6.74
6.12
6.51
7.27
8.42
11.48
11
1.46
1.58
1.68
1.77
1.88
1.97
2.47
2.48
2.54
4.97
N/A
Flanged Joint*
Mechanical Joint
No allowance is made in
offset figures for gasket thickness.
11
2.63
3.02
3.41
3.61
4.00
4.39
4.39
4.58
4.78
5.17
5.75
7.32
Mechanical Joint
Angle
45
22
11
D
Equals
T x 1.414
T x 2.613
T x 5.126
R
Equals
T x 1.000
T x 2.414
T x 5.027
L
Equals
D-2A
D-2A
D-2A
Cut the Pipe somewhat shorter to allow for clearance in the joints.
11
Long
Radius
90
1.17
1.56
1.95
2.15
2.54
2.93
2.93
3.12
3.32
3.71
4.29
5.85
15.50
18.00
23.00
28.00
33.00
38.00
43.00
48.00
53.00
58.00
68.00
N/A
Example:
A 14-inch Mechanical Joint line is to be offset
12 feet on an angle of 45-degrees using two
C110 full-body Mechanical Joint bends. What
is the laying length (L) of pipe required to make
the connection between the two bends?
Solution:
D = 12'0" x 1.414 =16.968'
R = 12' x 1.000 = 12.000'
A = 7.5" or .625'
L = 16.968' - 1.250 = 15.718' or
approximately 15' 8".
49
12/15/08 8:24:32 AM
1-1/2"
2"
2-1/2"
3"
4"
5"
6"
8"
10"
12"
14"
15"
16"
18"
20"
24"
A
B,C,D
A
B,C,D
A
B,C,D
E,F
A,B
C,D
E,F
A,B
C,D
E,F
A,B
C,D
E,F
A,B
C,D
E,F
A,B
C,D
E,F
A,B
C,D
A,B
C,D
A,B
C,D
50-350
50-350
50-350
50-300
350
50-200
250-350
50-200
250-350
50-100
150-300
50-100
150-300
50-100
150-250
50-100
50-250
50-100
150-250
Size
2
2
3
3
4
5
6
8
10
12
14
16
18
20
24
256772_utility catalog.pdf 52
2.50
3.80
3.96
4.80
5.00
6.90
7.10
7.22
9.05
9.30
9.42
11.10
11.40
11.60
13.20
13.50
13.76
15.30
15.65
16.98
17.40
17.80
18.16
19.50
19.92
21.60
22.06
25.80
26.32
2.30.09
3.30.09
4.30.09
5.30.09
6.30.09
8.38.13
10.50.13
12.5019
15.88.19
1.90.06
2.35.09
3.35.09
4.38+.09
-.05
5.30+.09
-.05
6.30+.09
-.05
8.38+.13
-.09
10.56.09
12.50.09
15.83.09
2.38
3.50
4.50
5.50
6.50
8.62
10.75
12.75
15.88
Length
Of Bolts
2
2
2
2
2
3
3
3
3
3
4
4
4
5
5
PVC
PVC
PVC
C-900 C-905 STEEL O.D
DI O.D. DI O.D. SCH. PIPE
MIN. - MAX.
100
150
200
100
150
200
3.74
3.84
3.84
4.64
4.81
4.81
4.00
4.10
4.29
4.79-5.14
4.97-5.27
5.22-5.57
100
150
200
100
150
200
100
150
200
100
150
200
100
150
200
6.91
6.91
6.91
9.11
9.11
9.11
11.24
11.66
11.66
13.44
13.92
13.92
15.07
16.22
16.22
7.05-7.40
7.07-7.37
7.26-7.56
9.22-9.57
9.27-9.57
9.39-9.74
11.42-11.77
11.82-12.12
11.77-12.12
13.69-14.04
14.08-14.38
14.03-14.38
15.40-15.80
16.38-16.73
16.48-16.88
100
150
200
100
150
100
150
100
150
17.14
18.46
18.46
19.90
20.94
22.12
23.28
26.48
27.96
17.54-17.94
18.62-18.97
18.79-19.19
20.44
21.20
22.50
23.54
27.17
28.22
Pipe
Sizes
2
2
3
3
4
5
6
8
10
12
14
16
18
20
24
STEEL
TYPE O.D.
DR 41
32.5
25.18
2.50
1.90
2.38
2.88
3.50
STD.
STD.
STD.
STD.
1.90
2.38
2.88
3.50
4.80
4.50
O.D.
STD.
4.00
4.50
5.56
STD.
5.56
6.90
6.63
O.D.
STD.
6.00
6.63
9.05
8.63
O.D.
STD.
8.00
8.63
11.10
10.75.
O.D.
STD.
10.00
10.75
13.20
12.75
O.D.
STD.
12.00
12.75
15.30
O.D.
14.00
17.40
O.D.
16.00
19.50
STD.
18.00
21.60
STD.
20.00
25.80
STD.
24.00
Length
of Bolts
2
3
3
3
3
3
3
4
5
5
5
6
6
6
7
50
12/15/08 8:24:32 AM
Question: From what compound is the standard MJ gasket made and what is the highest water
temperature it will withstand? Are the TYTON
gaskets made from the same compound?
Answer: The standard MJ
gasket is made of vulcanized styrene butadiene rubber (SBR)
in accordance with ANSI/AWWA C111/A21.11. The recommended temperature range for SBR
gaskets is from 20F to 180F. SBR gaskets are suitable for water and wastewater, most moderate
chemicals, wet or dry organic acids, alcohols, ketones, *chloramines, and aldehydes.
SBR GASKETS ARE NOT
*Note: Rated for Chloramine concentrations of less than 5 parts per million.
NOTE: Review the 31U Submittal on pages 71 and 72 of this catalog for additional gasket information
uestion: Does Tyler Union Waterworks offer any other gaskets that will withstand temperatures
greater than180 F or for special service applications?
Answer: Yes! Tyler Union offers
other special services gaskets for MJ connections only.
Identification, temperature range and applications are listed below:
EPDM (Ethylene Propylene) - Minus 10F to 250F Ideal for water and wastewater, ozone and strong
oxidizing chemicals. May be used on steam within given temperature range and on hot air
without hydrocarbons. OT RECOMMENDED FOR HYDROCARBON SERVICE.
NEOPRENE (CR) - Minus 10F to 200F Recommended for moderate chemicals and acids, oil fats,
many solvents and air with hydrocarbons. Will not support combustion.
Nitrile (NBR) (Buna - N) (Hycar) - Minus 40F to 250F Ideally suited for gasoline, petroleum
products, hydrocarbons, water and mineral and vegetable oils.
FKM (Fluoroelastomer) Minus 10F to 425F Ideal for hydrocarbons, acids, vegetable oils, and petrolium
u
estion: According to AWWA, how much torque should be applied to Mechanical Joint T-bolts?
Q
Answer: The recommended torque ranges, as stated in ANSI/AWWA C600 are:
Joint Size
in.
(mm)
3
(76)
4-24
(102-610)
30-36
(762-914)
Q
42-48 (1067-1219)
Range of Torque
ft/lb
N/m
45-60
(61-81)
75-90
(102-122)
100-120
(136-163)
120-150
(163-203)
uestion: What type of Mechanical Joint T-bolt does Tyler Union Waterworks furnish?
supplies High-strength, Low-Alloy Steel T-bolts, in compliance with ANSI/AWWA
Answer: Tyler
C111/A21.11. Contents of standard MJ Accessory packs comply with ANSI/AWWA C111/A21.11.
Anti-Rotation T-bolts, Blue Fluoropolymer coated T-bolts and tainless teel (AISI 316 and AISI 304)
T-bolts are also available for special applications on request.
For applications requiring specific weights or laying lengths of our fittings, contact Tyler Union
256772_utility catalog.pdf 53
51
12/15/08 8:24:32 AM
Question:
Answer: The Standard T-bolts and Anti-Rotation T-bolts and Nuts are manufactured from
Corrosion Resistent, High-Strength, Low-Alloy Weathering Steel in accordance with ANSI/AWWA C111
(Current Revision). Blue Fluorokote #1, T-bolts and Nuts are manufactured from the same high quality
material as the standard T-bolts/Nuts but
a
fluoropolymer resin that is baked on and was
developed
highly corrosive soil conditions.
low alloy T-bolts and
Fluorokote #1 Green SS304 and Red SS316 comply with ANSI/AWWA C111/A21.11 (Current Revision).
Question: How is the torque range for flanged fittings and gaskets determined?
Answer: The required torque for flanged fittings and gaskets is not addressed in the ANSI/AWWA
C600 Standard. Generally, this torque range is determined by the flange gasket manufacturer
due to the various
gaskets, bolt patterns and fitting flange diameters available.
Question: What purpose does the cement mortar lining serve?
Answer: Cement mortar lining serves to prevent tuberculation
flow characteristics.
of
lining with improved strength. Tyler
applies a seal
proved for use in potable water systems and it will cover the entire fitting unless specified otherwise during
order placement. The exterior is coated for aesthetic and to aid in retarding corrosion prior to installation.
Question: Are the fittings furnished by Tyler
UL/FM approved?
offer fittings with any coatings other than an asphaltic seal coat?
offer
Answer:
256772_utility catalog.pdf 54
52
12/15/08 8:24:32 AM
NOTES:
1. Dimension B is unthreaded shank.
2. Draft, when required to be
6 degree maximum, may
be deducted from bolt head
dimensions, and radius
(B/2) may be changed to
suit draft.
3. Gates, if required, may
protrude a maximum of
1/8 inch above the top of
the bolt head.
4. Chamfer is optional if
threads are rolled.
Size
Inches
A
0.05
B
+0.030
-0.074
C
+0.25
-0.06
Threads
per Inch
E
J
+0.15
-0.03
R
Max.
x 3
1.50
0.625
3.0
2.00
11
0.625 +or -.04
1.062-.04
0.625
0.312
x 3.5
1.75
0.750
3.5
2.50
10
0.750 +or -.06
1.250 -.06
0.750
0.375
x 4
1.75
0.750
4.0
3.00
10
0.750 +or -.06
1.250 -.06
0.750
0.375
x 4.5
1.75
0.750
4.5
3.00
10
0.750 +or -.06
1.250 -.06
0.750
0.375
x 5
1.75
0.750
5.0
3.00
10
0.750 +or -.06
1.250 -.06
0.750
0.375
1 x 6
1.75
1.000
6.0
3.00
8
1.000 +or -.08
1.625 -.08
1.000
0.500
1 x 7.5
2.25
1.000
7.5
4.50
8
1.000 +or -.08
1.625 -.08
1.000
0.625
1-1/4 x 6.5 2.50
1.250
6.5
3.50
7
1.250 +or -.08
2.000 -.08
1.250
0.750
1-1/4 x 8.5 2.50
1.250
8.5
4.00
7
1.250 +or -.08
2.000 -.08
1.250
0.750
The tolerance for cast iron bolts is +or-0.03". If threads are rolled, the body diameter may be reduced to the
approximate pitch diameter of the thread.
Tolerance:
+3, - 0 threads
Number of threads per inch - course-thread series (ANSI/ASME B1.1), Class 2A,
.
course-threads series (ANSI.ASME B1.1), Class 2A, external fit UNC2A and Class 2B, UNC2B (ANSI/ASME B1.2
Excavation
256772_utility catalog.pdf 55
12/15/08 8:24:33 AM
MJ FIELD LOK
PROVEN JOINT
RESTRAINT TECHNOLOGY
A RESTRAINT REVOLUTION. Spend less time and money - restraining mechancial joint fittings
with the new MJ FIELD LOK Gasket.
NO LEARNING CURVE
FOR DUCTILE IRON
AND PVC PIPE
CURRENTLY AVAILABLE:
Ductile Iron 4" - 24"
Pressure rated at a 2:1 safety factor, based on the pressure rating of the pipe on which it is installed.
Ductile iron locking ring provides proven joint restraint
technology.
256772_utility catalog.pdf 57
54
12/15/08 8:24:33 AM
Application Notes:
1. MJ FIELD LOK Gaskets are
designed to seal and restrain a
centrifugally cast ductile iron or PVC
pipe spigot in either a ductile iron
pipe or a ductile iron fitting bell.
4
6
8
10
12
14
16
18
20
24
4.80
6.90
9.05
11.10
13.20
15.30
17.40
19.50
21.60
25.80
DI04
DI06
DI08
DI10
DI12
DI14
DI16
DI18
DI20
DI24
3
4
6
9
13
18
24
30
36
52
APPROX.
KIT
WEIGHT
350
350
350
350
350
350
350
250
250
250
7.3
10.9
13.5
18.5
19.7
26.9
31.8
49.8
59.7
81.3
4
6
8
10
12
4.80
6.90
9.05
11.10
13.20
PRESSURE PRESSURE
ORDER
RATING
RATING
NUMBER
DR-18
DR-14
(psi)
(psi)
PV04
PV06
PV08
PV10
PV12
150
150
150
150
150
APPROX.
KIT
WEIGHT
200
200
200
200
200
7.8
11.8
14.8
20.1
21.6
4
6
8
10
12
14
16
18
20
24
3.3
5.0
7.2
10.2
11.0
17.2
25.0
38.0
46.0
64.0
8.88
10.87
13.13
15.38
17.63
20.13
22.38
24.75
27.00
31.50
Suggested Specifications:
7.50
9.50
11.75
14.00
16.25
18.75
21.00
23.25
25.50
30.00
4.90
7.00
9.15
11.20
13.30
15.44
17.54
19.64
21.74
25.94
5.92
8.02
10.17
12.22
14.32
16.40
18.50
20.60
22.70
26.90
1.75
2.00
2.25
2.25
2.25
2.51
2.75
3.14
3.20
3.57
Joint restraint for mechanical joint pipe and fittings shall be the MJ FIELD LOK Gasket. The restraint system shall be completely integral to the
gasket, requiring only standard mechanical joint assembly techniques. The restraining system for ductile iron shall be pressure rated to 350
psi in sizes up to and including 16"; 18", 20" and 24" are rated for 250 psi. The restraining system for PVC shall be rated at a 2:1 safety factor
for the pipe on which it is installed. The restraining system shall be rated in accordance with the performance requirements of ANSI/AWWA
C111/A21.11 Rubber Gasket Joints for Ductile-Iron Pressure Pipe and Fittings. Not recommended for use on Ductile iron Plain end fittings.
256772_utility catalog.pdf 58
55
12/15/08 8:24:33 AM
METHOD
ASTM D4060
ASTM D3359 - Method A
ASTM D3359 - Method B
ASTM D523
ASTM D2247
ASTM D2794
ASTM D3363
ASTM B117
Water Resistance
Weather Resistance
AWWA C550
ASTM G154
TABLE #1
CONDITIONS
CS-17 wheels, 1000 cycles, 1 kg load
X-cut and tape
Crosshatch and tape
N/A
1000 hours at 100F
N/A
N/A
1000 hours
90 days immersion at 70C
UVA-340, cycle 4 hrs UV at 60C, 4
hrs condensation at 50C
RESULT
32 mg loss
5A
5B
70-85
No blisters or rusting
Pass 40 inch-lbs. direct
Pass 4H
No blisters or face rust,
no scoreline creepage
Pass
Chalks after 200 hours
exposure
56
57
Pressure washing of cement linings is not recommended. However, if required contact your Tyler Union representative for instructions
before proceeding. Failure to follow these instructions or provide suitable supporting documentation will void the warranty on our lining.
Tyler Union Waterworks Call Centers
Tyler: 11910 CR 492 Tyler, Texas 75706 (800) 527-8478
Anniston: 1501 W. 17th. St. Anniston, Alabama 36201 (800) 226-7601
Corona: 1001 El Camino Ave. Corona, California 92879 (866) 527-8471
58
NSF-61 & NSF-372:...... Meets all requirements including Annex G, Tyler Unions Underwriters Laboratory listing MH16439.
ASPHALTIC COATING: Per ANSI/AWWA C104/A21.4 and ANSI/AWWA C110/A21.10.
CEMENT LINING:. Per ANSI/AWWA C104/A21.4, with double cement lining available upon request.
EPOXY COATING:... Fusion bonded epoxy per ANSI/AWWA C116/A21.16. Additional coatings available upon request.
BARE FITTINGS:.. Available upon request.
FASTENERS:.. High strength low alloy weathering steel per ANSI/AWWA C111/A21.11 and ASTM A242
INSTALLATION:. Install per AWWA C600/C651 using pipe conforming to ANSI/AWWA C151/A21.51 or AWWA C900/905.
59
60
DEFLECTION:....
NSF-61 & NSF-372:...... Meets all requirements including Annex G, Tyler Unions Underwriters Laboratory listing MH16439.
ASPHALTIC COATING: Per ANSI/AWWA C104/A21.4 and ANSI/AWWA C153/A21.53.
CEMENT LINING:. Per ANSI/AWWA C104/A21.4, with double cement lining available upon request.
EPOXY COATING:... Fusion bonded epoxy per ANSI/AWWA C116/A21.16. Additional coatings available upon request.
BARE:... Available upon request
FASTENERS:.. Per ANSI/AWWA C111/A21.11 and/or ASTM A242 high strength low alloy weathering steel
INSTALLATION:. Per AWWA C600 and C651 using pipe conforming to ANSI/AWWA C151/A21.51 or AWWA C900/905.
61
62
24U-*Mechanical Joint
Retainer Gland
Series 100
Revised 4/2013
SUBMITTAL
Pressure
Rating,
Size
psi
3
4
6
8
10
12
14
16
18
20
24
350
350
350
250
250
150
250
200
200
200
150
7.69
9.12
11.12
13.37
15.62
17.88
20.25
22.50
24.75
27.00
31.50
3.96
4.80
6.90
9.05
11.10
13.20
15.30
17.40
19.50
21.60
25.80
50-56
50-56
50-56
50-56
50-56
50-56
53-56
53-56
53-56
53-56
53-56
No of Size of
Set
Set
Gland Wt w/
Screws Screws
Wt Acces.
4
4
6
9
12
16
20
24
24
28
32
x2
4
x2
5
x2
9
x2
13
x2
17
x2
20
x2 44
x2 54
x2 62
x3
76
x3 103
8
11
16
21
26
28
55
64
72
91
118
www.tylerunion.com
63
25U-Compact
Mechanical Joint
Tapping Sleeve for
SUBMITTAL
SIZES:....................... For 6-12 PVC/ductile pipe per ANSI/AWWA C900 or C151 & Cast iron pipe
O.D. as provided. Comes with 4"-12" side flanged outlet & tap at branch.
STANDARDS:............ Mechanical and *Flanged joints comply with applicable requirements of
ANSI/AWWA C153 and ASME/ANSI B16.1. Cast with tested and traceable
ASTM A536 ductile iron. Ductile iron Mechanical Joint Tapping Sleeves are
produced in accordance with Tyler Union manufacturers standard. are
Dimension and specification ranges are per the standards as provided.
Note: Recess dimensions are per Manufacturers Standardization Society
standard practice SP-60. Meets requirements of MSS SP-111
PRESSURE RATING:.. 6- 12 Assemblies rated @ 250 PSI.
GASKETS:................. SBR Mechanical Joint and Split gaskets are per ASTM D2000 - AA and
ANSI/AWWA C111/21.11, armor tipped with coiled brass wire spring.
NSF-61& NSF-372:. Meets all requirements including Annex G
ASPHALTIC
COATING:................. ANSI/AWWA C104/A21.4
CEMENT LINING:..... Tapping Sleeves are unlined to ensure
they fit over the pipe being tapped.
FLANGE:................... ASME/ANSI B16.1, Class 125
FLANGE THICKNESS:.ANSI/AWWA C153 and ASME B16.1
BOLTS:.......... ANSI/AWWA C111/A21.11
DEFLECTION:............ Deflection is not recommended
INSTALLATION:........ Per Tyler Union instructions as provided
1.
2.
3.
4.
5.
6.
Dimensions
Size
A
B
C
D
E
F
Min.
Max.
DI
6x4
6
8x4
8x6
8
10x4
10x6
10x8
10
12x4
12x6
12x8
12x10
12
5.016
7.016
5.016
7.016
9.016
5.016
7.016
9.016
11.016
5.016
7.016
9.016
11.016
13.016
.250
.312
.250
.312
.312
.250
.312
.312
.312
.250
.312
.312
.312
.312
7.50
9.50
7.50
9.50
11.75
7.50
9.50
11.75
14.25
7.50
9.50
11.75
14.25
17.00
15.75
15.75
16.50
16.50
16.50
24.00
24.00
24.00
24.00
26.50
26.50
26.50
26.50
26.50
8.00
8.00
9.00
9.00
9.00
11.00
11.00
11.00
11.00
12.00
12.00
12.00
12.00
12.00
12.75
12.75
13.375
13.375
13.375
20.75
20.75
20.75
20.75
23.25
23.25
23.25
23.25
23.25
6.85
6.85
9.00
9.00
9.00
11.04
11.04
11.04
11.04
13.14
13.14
13.14
13.14
13.14
7.15
7.15
9.35
9.35
9.35
11.45
11.45
11.45
11.45
13.56
13.56
13.56
13.56
13.56
104
108
134
140
148
236
240
246
257
273
286
292
303
320
DEFLECTION:....
NSF-61 & NSF-372:...... Meets all requirements including Annex G, Tyler Unions Underwriters Laboratory listing MH16439.
ASPHALTIC COATING: Per ANSI/AWWA C104/A21.4 and ANSI/AWWA C153/A21.53.
CEMENT LINING:. Per ANSI/AWWA C104/A21.4, with double cement lining available upon request.
EPOXY COATING:... Fusion bonded epoxy per ANSI/AWWA C116/A21.16. Additional coatings available upon request.
BARE:... Available upon request.
FASTENERS:.. Per ANSI/AWWA C111/A21.11 and/or ASTM A242 high strength low alloy weathering steel
RESTRAINING LUGS:.. *Lugs provided on 16 and smaller fittings. Lug pattern accommodates most gripper type restraints.
*Note: With sufficient lead time to adapt tooling, restraining lugs are available on 18-24 fittings.
INSTALLATION:. Per AWWA C600 and C651 using pipe conforming to ANSI/AWWA C151/A21.51 or AWWA C900/905.
Designed for use with TYTON and McWane Sure Stop gaskets. Contact Tyler Union regarding the
installation or use of other gasket types and/or gasket manufacturers.
65
66
67
NSF-61 & NSF-372:..... Meets all requirements including Annex G, Tyler Unions Underwriters Laboratory listing MH16439
COATING: ... Asphaltic or Primer per ANSI/AWWA C104/A21.4, Standard primer is Tnemec Pota Pox 140N-1211
Contact Tyler Union for additional coating options
CEMENT LINING:. Per ANSI/AWWA C104/A21.4, with double cement lining available upon request.
EPOXY COATING:... Fusion bonded epoxy per ANSI/AWWA C116/A21.16. Additional coatings available upon request.
BARE:... Available upon request
FLANGES:... ANSI Class 125 per ASME B16.1 and ANSI/AWWA C111/A21.11
Note: *ANSI Class 250 ASME B16.1 flanged fittings available upon request
Note: *Due to larger bolt sizing and bolt circle, Class 250 flanges are not compatible with
Class 125 flanged fittings. AWWA C110 and AWWA C115 Class 125 flanges are compatible.
FLANGE THICKNESS:. ANSI/AWWA C115/A21.15 standard class 125 template for drilling bolt holes
Note: Drilling templates are in multiples of 4, so that fittings may be made face to in any quarter.
Bolt holes shall straddle the center line.
FASTENERS:.. Per ANSI/AWWA C111/A21.11 and/or ASTM A242 high strength low alloy weathering steel
INSTALLATION:. Per AWWA C600 and C651 using pipe conforming to ANSI/AWWA C151/A21.51
68
29U-Domestic Heavy
Duty Cast Iron Curb, Service,
& Valve Boxes + Components
Revised 04/2013
SUBMITTAL
For 3 to 20 Valves
5 Shaft, Screw Type
For 4 to 12 Valves
5 Shaft, Slip Type
For 4 to 12 Valves
5 Shaft, Slip Type
Extension
Components
Height
10T + 15B
19-22
27-32
10T + 24B
16T + 24B
27-37
16T + 30B
33-43
16T + 36B
39-50
26T + 30B
36-52
39-60
26T + 36B
26T + 24B + #60 Ext 53-71
26T + 36B + #60 Ext 64-82
Components)
10T + 12B
10T + 18B
16T + 24B
16T + 30B
16T + 36B
26T + 30B
26T + 36B
Extension
Height
27-37
33-42
39-49
45-54
51-60
45-66
51-72
Components
10T
10T
16T
16T
16T
26T
26T
26T
26T
+
+
+
+
+
+
+
+
+
15B
24B
24B
30B
36B
30B
36B
24B + #60 Ext
36B + #60 Ext
Extension
Height
19-22
27-32
27-37
33-43
39-50
36-52
39-60
53-71
64-82
Extension
Components
Height
26T + 24B
28-48
26T + 30B
34-54
26T + 36B
40-60
26T + 24B + #60 Ext 52-72
26T + 36B + #60 Ext 60-80
NOTE: Use the 6855 Bottoms
with these Tops
For to 2 Curbstops
6500 SCREW TYPE
CURB / SERVICE BOX
Extension
Componets
In Inches
18T & 27B
30-42
18T & 33B
36-48
24T & 33B
36-54
24T & 39B
42-60
30T & 39B
41-64
*Enlarged Base Available
T = Top
B = Bottom
EXT = Extension
www.tylerunion.com
69
30U-Non-Domestic
*Standard & Heavy
Duty Valve & Service
Boxes + Components
Revised 04/2013
SUBMITTAL
SIZES:..........................Adjustable Slip and Screw type with standard assembled lengths ranging from
15 to 72 (Lengths do not include risers, bases, and/or extensions). See the
Catalog or List Price guide for acc., lids, rings, bases, risers, meter covers, etc.
STANDARDS:...............Produced with cast iron in accordance with and meeting all applicable terms
and provisions of ASTM A-48. All Tyler Union valve boxes when properly
installed are suitable for use in conjunction with projects utilizing American
Association of State and Highway Transportation Officials (AASHTO) standards.
INSTALLATION:...........Per AWWA M44, Manual of Water Supply Practices
COATING:....................The asphaltic bituminous coating is applied to a minimum thickness of 1.5 mil and
the coating once dry is neither brittle when cold or sticky when eposed to the sun.
For 4 to 12 Valves
5 Shaft, Screw Type
For 3 to 20 Valves
5 Shaft, Screw Type
For 4 to 12 Valves
5 Shaft, Slip Type
Components
10T
10T
16T
16T
16T
26T
26T
26T
26T
+
+
+
+
+
+
+
+
+
Extension
Height
15B
24B
24B
30B
36B
30B
36B
24B + #60 Ext
36B + #60 Ext
19-22
27-32
27-37
33-43
39-50
36-52
39-60
53-71
64-82
Components)
10T
10T
16T
16T
16T
26T
26T
16T
26T
26T
+
+
+
+
+
+
+
+
+
+
Extension
Height
12B
27-37
18B
33-42
24B
39-49
30B
45-54
36B
51-60
30B
45-66
36B
51-72
24B + #60 Ext 63-72
24B + #60 Ext 63-84
36B + #60 Ext 74-94
Components
10T
10T
16T
16T
16T
26T
26T
26T
26T
+
+
+
+
+
+
+
+
+
15B
24B
24B
30B
36B
30B
36B
24B + #60 Ext
36B + #60 Ext
Extension
Height
19-22
27-32
27-37
33-43
39-50
36-52
39-60
53-71
64-82
B = Bottom
+
+
+
+
+
+
+
+
+
+
12B
15B
15B
21B
27B
27B
33B
33B
39B
39B
15-21
18-24
21-27
24-33
30-39
30-42
36-48
36-54
42-60
41-64
T = Top
For to 2
Curbstops
EXT = Extension
*Note:Wall thickness of Standard weight boxes is 3/16" and the inside diameter is 1/8" greater than the dimensions provided
11910 CR 492-Tyler, TX 75706 - (800) 527-8478 / 1501 W. 17th St.-Anniston, AL - (800) 226-7601
1001 El Camino Ave.-Corona, CA 92879-(866) 527-8471 / 6204 N. Maine Dr.-Portland, OR 97203-(866)527-8471
www.tylerunion.com
70
31U-Standard Mechanical
& Push-On Joint Gaskets
(SBR, NBR, EPDM, Neoprene, FKM)
Revised 4/2013
Page 1 of 2
SUBMITTAL
Required Value
75 (+-5)
1500 psi (10MPa)
150 %
60 %
20 %
No cracking
Tyler Union's approved suppliers maintain a quality assurance program that is reviewed and updated on an ongoing basis
to ensure product quality. Tyler Union's gasket suppliers submit gaskets for testing and provide materials for testing to Underwriters
Laboratories, Inc. Tyler Union's gasket providers are recognized under the component program (UL 194/ UL 157) of Underwriters
Laboratories, Inc.. Tyler Union UL approved gaskets meet NSF-61, NSF-372 and Annex G.
Tyler Union provides that our Mechanical and Push-On joint gaskets for potable or wastewater projects will perform as designed
when selected per the chart provided and installed per AWWA C600-10.
SBR (Styrene Butadiene rubber)(Buna-S)
20F to180F Suitable for Water, Wastewater, most moderate chemicals, wet or
Not Recommended for Hydrocarbon Service
dry organic acids, alcohols, ketones, and aldehydes
EPDM (Ethylene Propylene)
-10F to 250F Ideal for water, wastewater, ozone, & strong oxidizing chemicals
Not Recommended for Hydrocarbon Service
May be used on steam and air within its temperature range
CR (Neoprene)
-10F to 200F Recommended for moderate chemicals and acids, oil fats, greases,
many solvents and air with hydrocarbons. Will not support combustion
NBR (Nytril)(Buna-N)(Hycar)
-40F to 250F Ideally suited for gasoline, petrolium products, hydrocarbons, water,
mineral and vegetable oils
*FKM(Fluoroelastomer)
10F to 425F Ideally suited for hydrocarbons, acids, vegetable oils & petrolium
*Check with Customer Service for availability
Gasket Types Offered:
Unless other wise requested by the purchaser upon order placement, all gaskets provided will be of our standard SBR
material.
www.tylerunion.com
71
31U-Standard Mechanical
& Push-On Joint Gaskets
(SBR, NBR, EPDM, Neoprene, FKM)
Page 2 of 2
Mechanical Joint Gasket Dimensions in Inches
Pipe
Size
Pipe
OD
2**
3
4
6
8
10
12
14
16
18
20
24
30
36
42
48
2.50
3.96
4.80
6.90
9.05
11.10
13.20
15.30
17.40
19.50
21.60
25.80
32.00
38.30
44.50
50.80
A
B
C
0.01"
.48
.48
.62
.62
.62
.62
.62
.62
.62
.62
.62
.62
.62
.62
.75
.75
.75
.75
.75
.75
.75
.75
.75
.75
.31
.31
.31
.31
.31
.31
.31
.31
.31
.31
.31
.31
D
1%
2.48
3.86
4.68
6.73
8.85
10.87
12.95
14.99
17.07
19.13
21.20
25.34
E
0.01%
.12
.12
.16
.16
.16
.16
.16
.16
.16
.16
.16
.16
F
0.01"
G
0.02"
.15
.15
.22
.22
.22
.22
.22
.22
.22
.22
.22
.22
1.05
1.05
1.22
1.22
1.22
1.22
1.22
1.22
1.22
1.22
1.22
1.22
Pipe
Size
2
3
4
6
10
A
B
C
0.01"
D
E
1%
F
0.01"
G
0.02"
.57
.62
.31
2.28
.16
.24
1.08
.70
.62
.31
3.45
.16
.37
1.11
.77
.75
.31
4.43
.16
.37
1.26
.76
.75
.31
6.53
.16
.36
1.25
.82
.75
.31
8.50
.16
.42
1.27
.79
.75
.31
10.59
.16
.39
1.26
www.tylerunion.com
72
BETTER BY DESIGN
SPECIFICATIONS:
Designed and proven to restrain plain end ductile iron pipe conforming to ANSI/AWWA C151/A21.51 in diameters 3 thru 48
Proven for use on heavy wall **Schedule 40 or greater steel pipe in sizes 3- 12 and on all sizes 3 to 16 when pipe O.D. and wall
thickness conforms to C151 **Note: IPS diameter steel pipe requires the use of an MJ Transition gasket
Restraint design conforms with applicable requirements of ANSI/AWWA C111, ANSI/AWWA C153, and ANSI/AWWA C110
Restraint engineered for securing plain end pipe to mechanical joint fittings conforming to ANSI/AWWA C110, C111, and C153
Restraints rated for working water pressure of 350 psi and transitory surges of 100psi for 3 thru 16 and 250 psi for 18 thru 48
Cast of ASTM A536 compliant 65-45-12 ductile iron complete with a cast on date code and country of origin for traceability
Restraints and all components are designed and proven for a 2:1 safety factor based on the pipe pressure rating
Restraint deflection rating when installed on nominal diameter pipe is 3- 3, 4-12 - 5, 14-16 - 2, and 18-48 - 1.5
Standard coating for Domestic restraint is 4-6 mil of TUF-Bond(thermoset polyester for impact, corrosion and UV protection)
Gripping wedges are heat treated to a mininum 420 Brinell Hardness
Gripping wedge, wedge collar bolt, and twist off torque limiting nut shall be e-coated
FM approved for 4 thru 12 applications and UL listed and approved for 3 thru 24 applications
Not recommended for use on plain end fittings
Color coded black for pipe type(ductile/*cast iron/**steel) - *Note: Refer to page 2 for cast iron and page 3 for steel pipe applications
Torque limiting nut on gripping wedge assembly twists off within a designed torque range eliminating the need for specialized tools
Gripping wedge assembly pivots providing stronger engagement of pipe wall at lower torque requirement (45-60 ft.-lbs.)
Proven restraint technology utilizing fewer gripping wedges in frequently applied diameters, reducing trench time and project cost
Restraints heavy duty construction and design eliminates the need for costly thrust blocks and tie rods
Suitable for Potable and Wastewater applications
Name of Project
Project Engineer
Spec. Section
and/or Project No.
73
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
113805
113812
113829
113836
113843
113850
113867
113874
113898
113904
113911
461289
461333
461319
461326
Wedge
Qty.
T-Head
Bolt Qty.
Bolt Size
Gland
Weight(lbs.)
Weight
(w/Acc.)
Pressure
Rating
Pipe
O.D.
2
2
3
3
6
8
10
12
12
14
16
20
24
28
32
4
4
6
6
8
8
10
12
12
14
16
20
24
28
32
x 3
x 3.5
x 4
x 4
x 4
x 4
x 4.5
x 4.5
x 4.5
x 4.5
x 5
6.5
7.1
11.2
13.1
26.0
31.5
43.3
54.1
59.8
69.8
90.4
248
277
448
519
10.5
11.8
18.8
20.3
32.5
40.4
53.6
66.3
72.2
83.8
106.9
290
327
512
597
350
350
350
350
350
350
350
350
250
250
250
250
250
250
250
3.96
4.80
6.90
9.05
11.10
13.20
15.30
17.40
19.50
21.60
25.80
32.00
38.30
44.50
50.80
1 x 7.5
1 x 7.5
1-1/4 x 8.5
1-1/4 x 8.5
STOP-LOOK :
Extra length T-Head bolts are provided with 30 thru 48 inch restraints to facilitate mechanical joint assembly
For UL/FM Approvals, 3-12 inch were tested at 5of deflection and 14-24 inch were tested at 3 of deflection; all test were to 700 psi
The Series 1000 TUF Grip is specified for use on ductile iron pipe but can be used on some sizes of cast grey iron or pit cast pipe
if the pipe is not severely corroded, is in sound condition, and has an outside diameter compatible with the as provided dimensions
TUF Grip 30 to 48 inch provided with TRU-Lock mechanical joint gasket to ensure pressure ratings and safety factors are met
Installation and hydrostatic testing shall be in accordance with AWWA C600 and AWWA C651
*Tyler Union Waterworks Contact Information*
Tyler: 11910 CR 492 Tyler, Texas 75706 (800) 527-8478
th
Anniston: 1501 W 17 St. Anniston, AL 36201 (800) 226-7601
Corona: 1001 El Camino Ave. Corona, CA 92879 (866) 527-8471
www.tylerunion.com
74
1.
2.
3.
Step : 3
Insure the beveled pipe end to be joined and mechanical joint socket are clean and free of debris. Slide the BLACK
TUF Grip onto the pipe to be restrained. The TUF Grip compression lip extension must be toward the beveled end of
the pipe to be restrained.
Evenly lubricate the beveled pipe end, pipe wall exterior, and inside surface of the MJ gasket with a lubricant that
meets the requirements of AWWA C111. Now place the **MJ gasket over the plain beveled end of the pipe with the
narrow edge of the tapered gasket toward the beveled end of the pipe to be restrained. **NOTE : For Steel pipe
with IPS diameter in sizes 3-12, use of a MJ Transition gasket is required.
Fully insert the pipe end into the MJ socket pipe landing. Keeping the pipe straight, slide/push the MJ gasket firmly
and evenly into the socket recess. Joint must be kept straight during assembly.
Steps : 4 and 5
4.
5.
6.
7.
Steps : 6 and 7
Push the TUF Grip compression lip extension evenly against the thick side of the gasket and insert T-Head bolts
with the T-Head against the back side of the MJ fitting bolt flange. Use only T-Head bolts and nuts that meet AWWA
C111 requirements. Evenly hand-tighten the nuts on the T-Head bolts making sure the gland is centered around the
pipe and within the MJ socket. If joint deflection is needed, only deflect the pipe in the joint after hand tightening of
all nuts is completed. *Joint deflection is 3 max for 3, 5 max for 4-12, 2 max for 14-16, and 1.5 max for 1848.
*NOTE : Maximum deflection values provided apply with nominal pipe, fitting, and restraint diameters.
Using a wrench, tighten the nuts on the T-Head bolts a few turns at a time in an alternating or star pattern
maintaining equal spacing or distance between the TUF Grip bolt flange and face of the MJ socket bolt flange as the
MJ gasket is compressed. The T-Head bolt and nut torque requirement is 3- 45-60 ft.-lbs., 4- 24-75-90 ft.-lbs.,
30- 36- 100-120 ft.-lbs., and 42- 48- 120-150 ft.-lbs.. DO NOT OVER-TORQUE!
Hand-tighten the torque limiting nut attached to each TUF Grip wedge assembly in a clockwise direction with an
alternating or star pattern until all gripping wedges are in contact with the pipe wall. Rotational direction of torque
limiting nut is indicated by recessed arrow on the face of the nut. With a wrench (box, socket, or pneumatic),
continue to tighten each torque nut turn in an alternating or star pattern around the restraint until all torque
limiting nuts twist off. NEVER turn a torque limiting nut more than turn without turning the remaining torque nuts
an equal amount!
When all torque limiting nuts twist off, the assembly of the mechanical joint is complete.
8.
75
BETTER BY DESIGN
SPECIFICATIONS:
Designed and proven to restrain plain end ductile iron pipe conforming to ANSI/AWWA C151/A21.51 in diameters 3 thru 48
Proven for use on heavy wall **Schedule 40 or greater steel pipe in sizes 3- 12 and on all sizes 3 to 16 when pipe O.D. and wall
thickness conforms to C151 **Note: IPS diameter steel pipe requires the use of an MJ Transition gasket
Restraint design conforms with applicable requirements of ANSI/AWWA C111, ANSI/AWWA C153, and ANSI/AWWA C110
Restraint engineered for securing plain end pipe to mechanical joint fittings conforming to ANSI/AWWA C110, C111, and C153
Restraints rated for working water pressure of 350 psi and transitory surges of 100psi for 3 thru 16 and 250 psi for 18 thru 48
Cast of ASTM A536 compliant 65-45-12 ductile iron complete with a cast on date code and country of origin for traceability
Restraints and all components are designed and proven for a 2:1 safety factor based on the pipe pressure rating
Restraint deflection rating when installed on nominal diameter pipe is 3- 3, 4-12 - 5, 14-16 - 2, and 18-48 - 1.5
Standard coating for Non-Domestic restraint is 4-6 mil of *Alkyd resin baking enamel -*Note: Epoxy coatings available upon request
Gripping wedges are heat treated to a mininum 420 Brinell Hardness
Gripping wedge, wedge collar bolt, and twist off torque limiting nut shall be e-coated
FM approved for 4 thru 12 applications and UL listed and approved for 3 thru 24 applications
Not recommended for use on plain end fittings
Color coded black for pipe type(ductile/*cast iron/**steel) - *Note: Refer to page 2 for cast iron and page 3 for steel pipe applications
Torque limiting nut on gripping wedge assembly twists off within a designed torque range eliminating the need for specialized tools
Gripping wedge assembly pivots providing stronger engagement of pipe wall at lower torque requirement (45-60 ft.-lbs.)
Proven restraint technology utilizing fewer gripping wedges in frequently applied diameters, reducing trench time and project cost
Restraints heavy duty construction and design eliminates the need for costly thrust blocks and tie rods
Suitable for Potable and Wastewater applications
Name of Project
Project Engineer
Spec. Section
and/or Project No.
76
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
113805
113812
113829
113836
113843
113850
113867
113874
113898
113904
113911
461289
461333
461319
461326
Wedge
Qty.
T-Head
Bolt Qty.
Bolt Size
Gland
Weight(lbs.)
Weight
(w/Acc.)
Pressure
Rating
Pipe
O.D.
2
2
3
3
6
8
10
12
12
14
16
20
24
28
32
4
4
6
6
8
8
10
12
12
14
16
20
24
28
32
x 3
x 3.5
x 4
x 4
x 4
x 4
x 4.5
x 4.5
x 4.5
x 4.5
x 5
6.5
7.1
11.2
13.1
26.0
31.5
43.3
54.1
59.8
69.8
90.4
248
277
448
519
10.5
11.8
18.8
20.3
32.5
40.4
53.6
66.3
72.2
83.8
106.9
290
327
512
597
350
350
350
350
350
350
350
350
250
250
250
250
250
250
250
3.96
4.80
6.90
9.05
11.10
13.20
15.30
17.40
19.50
21.60
25.80
32.00
38.30
44.50
50.80
1 x 7.5
1 x 7.5
1-1/4 x 8.5
1-1/4 x 8.5
STOP-LOOK :
Extra length T-Head bolts are provided with 30 thru 48 inch restraints to facilitate mechanical joint assembly
For UL/FM Approvals, 3-12 inch were tested at 5of deflection and 14-24 inch were tested at 3 of deflection; all test were to 700 psi
The Series 1000 TUF Grip is specified for use on ductile iron pipe but can be used on some sizes of cast grey iron or pit cast pipe
if the pipe is not severely corroded, is in sound condition, and has an outside diameter compatible with the as provided dimensions
TUF Grip 30 to 48 inch provided with TRU-Lock mechanical joint gasket to ensure pressure ratings and safety factors are met
Installation and hydrostatic testing shall be in accordance with AWWA C600 and AWWA C651
*Tyler Union Waterworks Contact Information*
Tyler: 11910 CR 492 Tyler, Texas 75706 (800) 527-8478
th
Anniston: 1501 W 17 St. Anniston, AL 36201 (800) 226-7601
Corona: 1001 El Camino Ave. Corona, CA 92879 (866) 527-8471
www.tylerunion.com
77
1.
2.
3.
Step : 3
Insure the beveled pipe end to be joined and mechanical joint socket are clean and free of debris. Slide the BLACK
TUF Grip onto the pipe to be restrained. The TUF Grip compression lip extension must be toward the beveled end of
the pipe to be restrained.
Evenly lubricate the beveled pipe end, pipe wall exterior, and inside surface of the MJ gasket with a lubricant that
meets the requirements of AWWA C111. Now place the **MJ gasket over the plain beveled end of the pipe with the
narrow edge of the tapered gasket toward the beveled end of the pipe to be restrained. **NOTE : For Steel pipe
with IPS diameter in sizes 3-12, use of a MJ Transition gasket is required.
Fully insert the pipe end into the MJ socket pipe landing. Keeping the pipe straight, slide/push the MJ gasket firmly
and evenly into the socket recess. Joint must be kept straight during assembly.
Steps : 4 and 5
4.
5.
6.
7.
Steps : 6 and 7
Push the TUF Grip compression lip extension evenly against the thick side of the gasket and insert T-Head bolts
with the T-Head against the back side of the MJ fitting bolt flange. Use only T-Head bolts and nuts that meet AWWA
C111 requirements. Evenly hand-tighten the nuts on the T-Head bolts making sure the gland is centered around the
pipe and within the MJ socket. If joint deflection is needed, only deflect the pipe in the joint after hand tightening of
all nuts is completed. *Joint deflection is 3 max for 3, 5 max for 4-12, 2 max for 14-16, and 1.5 max for 1848.
*NOTE : Maximum deflection values provided apply with nominal pipe, fitting, and restraint diameters.
Using a wrench, tighten the nuts on the T-Head bolts a few turns at a time in an alternating or star pattern
maintaining equal spacing or distance between the TUF Grip bolt flange and face of the MJ socket bolt flange as the
MJ gasket is compressed. The T-Head bolt and nut torque requirement is 3- 45-60 ft.-lbs., 4- 24-75-90 ft.-lbs.,
30- 36- 100-120 ft.-lbs., and 42- 48- 120-150 ft.-lbs.. DO NOT OVER-TORQUE!
Hand-tighten the torque limiting nut attached to each TUF Grip wedge assembly in a clockwise direction with an
alternating or star pattern until all gripping wedges are in contact with the pipe wall. Rotational direction of torque
limiting nut is indicated by recessed arrow on the face of the nut. With a wrench (box, socket, or pneumatic),
continue to tighten each torque nut turn in an alternating or star pattern around the restraint until all torque
limiting nuts twist off. NEVER turn a torque limiting nut more than turn without turning the remaining torque nuts
an equal amount!
When all torque limiting nuts twist off, the assembly of the mechanical joint is complete.
8.
78
BETTER BY DESIGN
SPECIFICATIONS:
Designed and proven to restrain plain end ductile iron pipe conforming to ANSI/AWWA C151/A21.51 in diameters 4 thru 12
Restraint design conforms with applicable requirements of ANSI/AWWA C111, ANSI/AWWA C153, and ANSI/AWWA C110
Restraint engineered for securing plain end pipe to mechanical joint fittings conforming to ANSI/AWWA C110, C111, and C153
Rated restraint rated for working water pressure of 350 psi for 4 thru 12 restraints
Cast of ASTM A536 compliant 65-45-12 ductile iron complete with a cast on date code and country of origin for traceability
Restraints and all components are designed and proven for a 2:1 safety factor based on the pipe pressure rating
Deflection rating when installed on AWWA C151 pipe with nominal diameter shall be 3 for 4 thru 12 restraints
Standard coating for Non-Domestic restraint is 4-6 mil of *Alkyd resin baking enamel -*Note: Epoxy coatings available upon request
Gripping wedges are heat treated to a mininum 420 Brinell Hardness
Gripping wedge, wedge collar bolt, and twist off torque limiting nut shall be e-coated
Not recommended for use on plain end fittings
Color coded black for pipe type(ductile pipe/*cast iron pipe) - *Note: Refer to page 2 for cast iron pipe application
Torque limiting nut on gripping wedge assembly twists off within a designed torque range eliminating the need for specialized tools
Gripping wedge assembly pivots providing stronger engagement of pipe wall at lower torque requirement (45-60 ft.-lbs.)
Proven restraint technology utilizing fewer gripping wedges in frequently applied diameters, reducing trench time and project cost
Restraints heavy duty construction and design eliminates the need for costly thrust blocks and tie rods
Suitable for Potable and Wastewater applications
Name of Project
Name of Contractor
Project Engineer
Spec. Section
and/or Project No.
Size (inches)
K2
4.93
5.92
7.03
8.02
7.50
8.98
10.67
7/8
2.20
0.73
9.50
10.98
12.77
7/8
2.24
9.18
0.82
10.17
11.75
13.23
14.92
7/8
2.28
10
0.82
11.23
12.22
14.00
15.70
16.97
7/8
2.37
12
0.93
13.33
14.32
16.25
17.95
19.07
7/8
2.40
0.93
Part # Gland+Accessories
Domestic / Non-Domestic
N/A
N/A
N/A
N/A
N/A
/
/
/
/
/
495918
495925
495932
495949
495956
Wedge
Qty.
T-Head
Bolt Qty.
Bolt Size
Gland
Weight(lbs.)
Weight
(w/Acc.)
Pressure
Rating
Pipe
O.D.
2
3
3
6
8
4
6
6
8
8
x 3.5
x 4
x 4
x 4
x 4
7.1
11.2
13.1
26.0
31.5
11.8
18.8
20.3
32.5
40.4
350
350
350
350
350
4.80
6.90
9.05
11.10
13.20
Assembly Steps Series 1000S TLD Split For Ductile Iron Pipe
Steps: 1 and 2
1.
2.
3.
4.
Insure the beveled pipe end to be joined and mechanical joint socket are clean and free of debris.
Lubricate the pipe end and exterior plus the inside surface of gasket with joint lubricant that meets the
requirements of AWWA C111. Now place the MJ gasket over the plain beveled end of the pipe with the narrow edge
of the tapered gasket toward the beveled end of the pipe to be restrained.
Fully insert the pipe end into the MJ socket pipe landing. Keeping the pipe straight, slide/push the gasket firmly and
evenly into the MJ socket recess.
Place the two halves of the black TUF Grip around the pipe with the compression lip extension toward the MJ
socket. Join the two restraint halves together with two T-Head bolts. Use only T-Head bolts, gaskets, and nuts that
meet AWWA C111 requirements.
Step: 5
5.
6.
7.
8.
9.
Step: 3 and 4
Steps: 6 and 7
Steps: 8 and 9
With the two T-Head bolts inserted through the restraint, push the TUF Grip lip extension evenly against the thick
side of the MJ gasket. With the TUF Grip restraint against the gasket, the remaining T-Head bolts are inserted with
the T-Head against the back of the MJ fitting bolt flange. Install two additional T-Head bolts with nuts and hand
tighten to secure the restraint to the fitting.
With the restraint secured to the fitting, remove the original assembly T-Head bolts and reinsert with the T-Head
against the back of the MJ fitting bolt flange. Making sure the TUF Grip is centered around the pipes wall, hand
tighten all remaining T-Head bolts and nuts. If joint deflection is needed, only deflect the pipe in the joint after hand
tightening of all nuts is completed. Maximum joint deflection is 3 when pipe and fitting dimensions are nominal.
Using a wrench, tighten the nuts on the T-Head bolts a few turns at a time in an alternating or star pattern. Maintain
equal spacing between the TUF Grip bolt flange and the bolt flange of the MJ socket as the gasket is compressed.
The T-Head bolt and nut torque requirement is 75-90 ft.-lbs. for 4 thru 12 restraints. DO NOT OVER-TORQUE!
Hand-tighten the torque limiting nut attached to the TUF Grip wedge assemblies in a clockwise direction with an
alternating or star pattern until all gripping wedges are in contact with the pipe wall. Rotational direction of torque
limiting nut is indicated by recessed arrow on the face of the nut. With a wrench, continue to tighten each torque
nut turn in an alternating or star pattern until all torque limiting nuts twist off. NEVER turn a torque limiting nut
more than turn without turning the remaining torque nuts an equal amount!
When all torque limiting nuts twist off, the assembly of the mechanical joint restraint is complete.
10.
81
BETTER BY DESIGN
SPECIFICATIONS:
Proven to restrain plain end PVC pipe in diameters 3 thru 36 and PVCO pipe in diameters 4 thru 12
Restraint design conforms to applicable requirements of ANSI/AWWA C111, ANSI/AWWA C153, and ANSI/AWWA C110
Restraint engineered for securing plain end pipe to mechanical joint fittings conforming to ANSI/AWWA C110, C111, and C153
Rated for working water pressure of 305 psi for 3-12, 235 psi for 14-24, 150 psi for 30, and 125 psi for 36 (details on page 2)
Cast of ASTM compliant 65-45-12 ductile iron complete with cast on date code and country of origin for traceability
Restraint and all components are designed and proven for a 2:1 safety factor based on the PVC and PVCO pipe pressure rating
Deflection rating when installed on pipe with nominal diameter shall be 3 for 3 thru 12, 2 for 14 thru 16, and 1.5 for 18 thru 36
Standard coating for Domestic restraint is 4-6 mil of TUF-Bond(thermoset polyester for impact, corrosion, and UV protection)
Gripping wedge, wedge collar bolt and twist off torque limiting nut shall be e-coated
FM approved for 4 thru 12 applications and UL listed and approved for 3 thru 12 applications
Color coded red for pipe type (C900 PVC/C905 PVC/ *C909 PVCO/D2241 PVC) - *Note: Refer to page 2 for C909 pipe applications
Torque limiting nut on gripping wedge assembly twists off within a designed torque range eliminating the need for specialized tools
Gripping wedge assembly pivots providing stronger engagement of pipe wall at lower torque requirement (45-60 ft.-lbs.)
Proven restraint technology utilizing fewer gripping wedges in frequently applied diameters, reducing trench time and project cost
There is no washer or spacer to remove when installing restraints on 3 to 12 ASTM D2241 PVC pipe with IPS outside diameter
Restraints heavy duty construction and design eliminates the need for costly thrust blocks and tie rods
Suitable for Potable and Wastewater applications
Approved for use on multiple classes of pipe - Additional pressure ratings and associated pipe classes provided on pages 2 and 3
Name of Project
Project Engineer
Spec. Section
and/or Project No.
82
/
/
/
/
/
/
/
/
/
/
/
/
/
113928
113935
113942
113959
113973
113980
113997
114000
114017
114024
114031
461302
461357
Wedge
Qty.
T-Head
Bolt Qty.
2
2
3
3
6
8
10
12
12
14
16
20
24
4
4
6
6
8
8
10
12
12
14
16
20
24
Bolt
Size
x 3
x 3.5
x 4
x 4
x 4
x 4
x 4.5
x 4.5
x 4.5
x 4.5
x 5
1 x 7.5
1 x 7.5
Gland
Weight(lbs.)
Weight
(w/Acc.)
*Pressure
Rating
Pipe O.D.
(Inches)
7.0
8.3
12.4
14.9
25.7
34.1
45.1
56.2
62.4
72.9
93.2
251
281
11.0
12.2
18.3
20.8
33.4
42.0
55.4
68.4
74.8
86.9
109.8
293
331
*305 / DR14
*305 / DR14
*305 / DR14
*305 / DR14
*305 / DR14
*305 / DR14
*235 / DR18
*235 / DR18
*235 / DR25
*235 / DR25
*235 / DR25
*150 / DR25
*125 / DR25
3.50
4.50-4.80
6.63-6.90
8.63-9.12
10.75-11.10
12.75-13.20
15.30
17.40
19.50
21.60
25.80
32.00
38.30
*Note: The pressure ratings are rated working water pressures for the restraint. See page 3 for additional ratings.
STOP-LOOK :
Extra length T-Head bolts are provided with 30- 36 restraints to facilitate mechanical joint assembly per AWWA C600.
For UL/FM Approvals, 3- 12 were tested to 755 psi, 14-16 were tested to 755 psi and 18- 24 inch were tested to 535 psi.
TUF Grip 30-36 inch provided with TRU-Lock mechanical joint gasket to ensure pressure rating & safety factors are met.
Mechanical joint T-head bolt torques for C909 applications are as provided; *55-65 ft.-lbs for 4 to 8 and *65 to 75 ft.-lbs. for
10 to 12 assembly. You must specifiy restraints are for C909 PVCO pipe upon order placement. Call for availability.
Installation and hydrostatic testing shall be in accordance with AWWA C600 and AWWA C651.
TUF Grip 4 to 24 restraints shall meet the requirementsof ASTM F1674, current revision.
*Tyler Union Waterworks Contact Information*
Tyler: 11910 CR 492 Tyler, Texas 75706 (800) 527-8478
th
Anniston: 1501 W 17 St. Anniston, AL 36201 (800) 226-7601
Corona: 1001 El Camino Ave. Corona, CA 92879 (866) 527-8471
www.tylerunion.com
83
305
305
305
305
305
-
235
235
235
235
235
-
165
165
165
165
165
-
235
235
200
200
165
-
165
165
165
165
165
165
125
125
125
125
125
125
250
250
250
250
250
250
-
200
200
200
200
200
200
-
160
160
160
160
160
-
**Note: Pressure Ratings for Ordinary Water Works Restraint Application with Transitory Surges Only
**Note: AWWA C909 PVCO Restraint Pressure Rating is per the Pressure Rating Listed on the Pipe
Assembly steps for (3-12 ASTM D2241 IPS PVC), (4-12 AWWA C909 PVCO), and (4-36 AWWAC900/C905 PVC)
Steps: 1 and 2
1.
2.
3.
4.
5.
6.
7.
Step: 3
Steps: 4 and 5
Steps: 6 and 7
Insure the beveled pipe end to be joined and mechanical joint socket are clean and free of debris. Slide the RED
TUF Grip onto the beveled end of the pipe to be restrained. The TUF Grip compression lip extension must be toward
the beveled end of the pipe being restrained.
Evenly lubricate the beveled pipe end, exterior pipe wall, and inside surface of the gasket with a lubricant that
meets the requirements of AWWA C111. Now place the **MJ gasket over the plain beveled end of the pipe with the
narrow edge of the tapered gasket toward the pipe end. **NOTE: Use MJ transition gasket with IPS diameter pipe.
Fully insert the beveled pipe end into the MJ socket pipe landing. Keeping the pipe straight in the MJ socket,
slide/push the MJ gasket firmly and evenly into the MJ socket recess. Joint must be kept straight during assembly.
Push the TUF Grip compression lip extension evenly against the thick side of the MJ gasket and insert all T-Head
bolts with nuts. Use only T-Head bolts and nuts that meet AWWA C111 requirements. With the TUF Grip restraint lip
extension against the MJ gasket, evenly hand-tighten the nuts on the T--Head bolts making sure the restraint body is
centered on the pipe and within in the MJ socket. If joint deflection is needed, deflect the pipe only after hand
tightening of all nuts is completed. Joint deflection is 3 max for 3, 5 max for 4-12, 2 max for 14-16, 1.5 max
for 18-36. NOTE: Maximum deflection values provided apply with nominal pipe, fitting, and restraint diameters.
Using a wrench, tighten the T-Head bolts and nuts a few turns at a time in an alternating or star pattern. Maintain
equal spacing or distance between the TUF Grip bolt flange and the MJ socket bolt flange as the MJ gasket is
compressed. Repeat the process in an alternating pattern for all T-Head bolts and nuts. The T-Head bolt and nut
torque requirement for restraints is 3- 45-60 ft.-lbs., 4- 24-75-90 ft.-lbs., and 30- 36- 100-120 ft.-lbs.
NOTE: The C909 PVCO T-Head bolt and nut torque is 55-65 ft.-lbs. for 4-8 and 65-75 ft.-lbs. for 10-12restraints.
DO NOT OVER-TORQUE T-HEAD BOLTS and NUTS WHEN ASSEMBLING PVC and PVCO PIPE!
**Hand-tighten the torque limiting nuts attached to the TUF Grip wedge assemblies in a clockwise direction with an
alternating or star pattern until all gripping wedges are in contact with the pipe wall. Rotational direction of torque
nut is indicated by recessed arrow on the face of the nut. With a wrench (box, socket, or pneumatic), continue to
tighten each torque nut turn in an alternating or star pattern around the restraint until all torque limiting nuts twist
off. NEVER turn a torque limiting nut more than turn without turning the remaining torque nuts an equal amount!
**NOTE: For IPS and PVCO applications, ensure step 5 is completed before engaging wedges. Failure to comply
will result in excessive pipe wall deflection and torque nuts will not twist off as designed.
When all torque limiting nuts twist off, the mechanical joint and restraint assembly are complete.
*Tyler Union Waterworks Contact Information*
Tyler: 11910 CR 492 Tyler, Texas 75706 (800) 527-8478
th
Anniston: 1501 W 17 St. Anniston, AL 36201 (800) 226-7601
Corona: 1001 El Camino Ave. Corona, CA 92879 (866) 527-8471
84
www.tylerunion.com
BETTER BY DESIGN
SPECIFICATIONS:
Proven to restrain plain end PVC pipe in diameters 3 thru 36 and PVCO pipe in diameters 4 thru 12
Restraint design conforms to applicable requirements of ANSI/AWWA C111, ANSI/AWWA C153, and ANSI/AWWA C110
Restraint engineered for securing plain end pipe to mechanical joint fittings conforming to ANSI/AWWA C110, C111, and C153
Rated for working water pressure of 305 psi for 3-12, 235 psi for 14-24, 150 psi for 30, and 125 psi for 36 (details on page 2)
Cast of ASTM compliant 65-45-12 ductile iron complete with cast on date code and country of origin for traceability
Restraint and all components are designed and proven for a 2:1 safety factor based on the PVC and PVCO pipe pressure rating
Deflection rating when installed on pipe with nominal diameter shall be 3 for 3 thru 12, 2 for 14 thru 16, and 1.5 for 18 thru 36
Standard coating for Non-Domestic restraint is 4-6 mil of *Alkyd resin baking enamel - *Note: Epoxy coatings available upon request
Gripping wedge, wedge collar bolt and twist off torque limiting nut shall be e-coated
FM approved for 4 thru 12 applications and UL listed and approved for 3 thru 12 applications
Color coded red for pipe type (C900 PVC/C905 PVC/ *C909 PVCO/D2241 PVC) - *Note: Refer to page 2 for C909 pipe applications
Torque limiting nut on gripping wedge assembly twists off within a designed torque range eliminating the need for specialized tools
Gripping wedge assembly pivots providing stronger engagement of pipe wall at lower torque requirement (45-60 ft.-lbs.)
Proven restraint technology utilizing fewer gripping wedges in frequently applied diameters, reducing trench time and project cost
There is no washer or spacer to remove when installing restraints on 3 to 12 ASTM D2241 PVC pipe with IPS outside diameter
Restraints heavy duty construction and design eliminates the need for costly thrust blocks and tie rods
Suitable for Potable and Wastewater applications
Approved for use on multiple classes of pipe - Additional pressure ratings and associated pipe classes provided on pages 2 and 3
Name of Project
Project Engineer
Spec. Section
and/or Project No.
85
/
/
/
/
/
/
/
/
/
/
/
/
/
113928
113935
113942
113959
113973
113980
113997
114000
114017
114024
114031
461302
461357
Wedge
Qty.
T-Head
Bolt Qty.
2
2
3
3
6
8
10
12
12
14
16
20
24
4
4
6
6
8
8
10
12
12
14
16
20
24
Bolt
Size
x 3
x 3.5
x 4
x 4
x 4
x 4
x 4.5
x 4.5
x 4.5
x 4.5
x 5
1 x 7.5
1 x 7.5
Gland
Weight(lbs.)
Weight
(w/Acc.)
*Pressure
Rating
Pipe O.D.
(Inches)
7.0
8.3
12.4
14.9
25.7
34.1
45.1
56.2
62.4
72.9
93.2
251
281
11.0
12.2
18.3
20.8
33.4
42.0
55.4
68.4
74.8
86.9
109.8
293
331
*305 / DR14
*305 / DR14
*305 / DR14
*305 / DR14
*305 / DR14
*305 / DR14
*235 / DR18
*235 / DR18
*235 / DR25
*235 / DR25
*235 / DR25
*150 / DR25
*125 / DR25
3.50
4.50-4.80
6.63-6.90
8.63-9.12
10.75-11.10
12.75-13.20
15.30
17.40
19.50
21.60
25.80
32.00
38.30
*Note: The pressure ratings are rated working water pressures for the restraint. See page 3 for additional ratings.
STOP-LOOK :
Extra length T-Head bolts are provided with 30- 36 restraints to facilitate mechanical joint assembly per AWWA C600.
For UL/FM Approvals, 3- 12 were tested to 755 psi, 14-16 were tested to 755 psi and 18- 24 inch were tested to 535 psi.
TUF Grip 30-36 inch provided with TRU-Lock mechanical joint gasket to ensure pressure rating & safety factors are met.
Mechanical joint T-head bolt torques for C909 applications are as provided; *55-65 ft.-lbs for 4 to 8 and *65 to 75 ft.-lbs. for
10 to 12 assembly. You must specifiy restraints are for C909 PVCO pipe upon order placement. Call for availability.
Installation and hydrostatic testing shall be in accordance with AWWA C600 and AWWA C651.
TUF Grip 4 to 24 restraints shall meet the requirementsof ASTM F1674, current revision.
*Tyler Union Waterworks Contact Information*
Tyler: 11910 CR 492 Tyler, Texas 75706 (800) 527-8478
th
Anniston: 1501 W 17 St. Anniston, AL 36201 (800) 226-7601
Corona: 1001 El Camino Ave. Corona, CA 92879 (866) 527-8471
www.tylerunion.com
86
305
305
305
305
305
-
235
235
235
235
235
-
165
165
165
165
165
-
235
235
200
200
165
-
165
165
165
165
165
165
125
125
125
125
125
125
250
250
250
250
250
250
-
200
200
200
200
200
200
-
160
160
160
160
160
-
**Note: Pressure Ratings for Ordinary Water Works Restraint Application with Transitory Surges Only
**Note: AWWA C909 PVCO Restraint Pressure Rating is per the Pressure Rating Listed on the Pipe
Assembly steps for (3-12 ASTM D2241 IPS PVC), (4-12 AWWA C909 PVCO), and (4-36 AWWAC900/C905 PVC)
Steps: 1 and 2
1.
2.
3.
4.
5.
6.
7.
Step: 3
Steps: 4 and 5
Steps: 6 and 7
Insure the beveled pipe end to be joined and mechanical joint socket are clean and free of debris. Slide the RED
TUF Grip onto the beveled end of the pipe to be restrained. The TUF Grip compression lip extension must be toward
the beveled end of the pipe being restrained.
Evenly lubricate the beveled pipe end, exterior pipe wall, and inside surface of the gasket with a lubricant that
meets the requirements of AWWA C111. Now place the **MJ gasket over the plain beveled end of the pipe with the
narrow edge of the tapered gasket toward the pipe end. **NOTE: Use MJ transition gasket with IPS diameter pipe.
Fully insert the beveled pipe end into the MJ socket pipe landing. Keeping the pipe straight in the MJ socket,
slide/push the MJ gasket firmly and evenly into the MJ socket recess. Joint must be kept straight during assembly.
Push the TUF Grip compression lip extension evenly against the thick side of the MJ gasket and insert all T-Head
bolts with nuts. Use only T-Head bolts and nuts that meet AWWA C111 requirements. With the TUF Grip restraint lip
extension against the MJ gasket, evenly hand-tighten the nuts on the T--Head bolts making sure the restraint body is
centered on the pipe and within in the MJ socket. If joint deflection is needed, deflect the pipe only after hand
tightening of all nuts is completed. Joint deflection is 3 max for 3, 5 max for 4-12, 2 max for 14-16, 1.5 max
for 18-36. NOTE: Maximum deflection values provided apply with nominal pipe, fitting, and restraint diameters.
Using a wrench, tighten the T-Head bolts and nuts a few turns at a time in an alternating or star pattern. Maintain
equal spacing or distance between the TUF Grip bolt flange and the MJ socket bolt flange as the MJ gasket is
compressed. Repeat the process in an alternating pattern for all T-Head bolts and nuts. The T-Head bolt and nut
torque requirement for restraints is 3- 45-60 ft.-lbs., 4- 24-75-90 ft.-lbs., and 30- 36- 100-120 ft.-lbs.
NOTE: The C909 PVCO T-Head bolt and nut torque is 55-65 ft.-lbs. for 4-8 and 65-75 ft.-lbs. for 10-12restraints.
DO NOT OVER-TORQUE T-HEAD BOLTS and NUTS WHEN ASSEMBLING PVC and PVCO PIPE!
**Hand-tighten the torque limiting nuts attached to the TUF Grip wedge assemblies in a clockwise direction with an
alternating or star pattern until all gripping wedges are in contact with the pipe wall. Rotational direction of torque
nut is indicated by recessed arrow on the face of the nut. With a wrench (box, socket, or pneumatic), continue to
tighten each torque nut turn in an alternating or star pattern around the restraint until all torque limiting nuts twist
off. NEVER turn a torque limiting nut more than turn without turning the remaining torque nuts an equal amount!
**NOTE: For IPS and PVCO applications, ensure step 5 is completed before engaging wedges. Failure to comply
will result in excessive pipe wall deflection and torque nuts will not twist off as designed.
When all torque limiting nuts twist off, the mechanical joint and restraint assembly are complete.
*Tyler Union Waterworks Contact Information*
Tyler: 11910 CR 492 Tyler, Texas 75706 (800) 527-8478
th
Anniston: 1501 W 17 St. Anniston, AL 36201 (800) 226-7601
Corona: 1001 El Camino Ave. Corona, CA 92879 (866) 527-8471
www.tylerunion.com
87
Better by Design
SPECIFICATIONS:
Unique Split design assembles using standard T-bolts and without additional accessories in sizes 6 thru 12
Torque limiting nut on gripping wedge assembly twists off within a designed torque range eliminating the need for specialized tools
Gripping wedge assembly pivots providing stronger engagement of pipe wall at lower torque requirement (45-60 ft.-lbs.)
Proven restraint technology utilizing fewer gripping wedges in frequently applied diameters, reducing trench time and project cost
There is no washer or spacer to remove when installing restraints on 4 to 12 ASTM D2241 PVC pipe with IPS outside diameter
Restraints heavy duty construction and design eliminates the need for costly thrust blocks and tie rods
Suitable for Potable and Wastewater applications
Approved for use on multiple classes of pipe - Additional pressure ratings and associated pipe classes provided on page 2
Name of Project
Name of Contractor
Project Engineer
Spec. Section
and/or Project No.
88
Size (inches)
K2
4
6
8
10
12
4.93
7.03
9.18
11.23
13.33
5.92
8.02
10.17
12.22
14.32
7.50
9.50
11.75
14.00
16.25
8.98
10.98
13.23
15.70
17.95
10.67
12.77
14.92
16.97
19.07
7/8
7/8
7/8
7/8
7/8
2.20
2.24
2.28
2.37
2.40
0.73
0.82
0.82
0.93
0.93
Part # Gland+Accessories
Domestic / Non-Domestic
Wedge
Qty.
T-Head
Bolt Qty.
Bolt
Gland
Weight
Size
Weight(lbs.)
(w/Acc.)
x 3.5
4
N/A
/
537052
2
4
8.3
12.2
6
N/A
/
537069
3
6
x 4
12.4
18.3
x 4
8
N/A
/
537076
3
6
14.9
20.8
10
N/A
/
537083
6
8
x 4
25.7
33.4
x 4
12
N/A
/
537090
8
8
34.1
42.0
*Note: The Pressure Ratings are Rated Working Water Pressures for the Restraint.
*Pressure
Rating
Pipe O.D.
(Inches)
*305 / DR14
*305 / DR14
*305 / DR14
*305 / DR14
*305 / DR14
4.50-4.80
6.63-6.90
8.63-9.12
10.75-11.10
12.75-13.20
DR14
4
6
8
10
12
305
305
305
305
305
AWWA C900
DR18
235
235
235
235
235
DR25
SDR17
150
150
150
150
150
250
250
250
250
250
ASTM D2241
SDR21
SDR26
200
200
200
200
200
160
160
160
160
-
**Note: Ratings for Ordinary Water Works Restraint Applications with Transitory Surges Only
STOP-LOOK :
Piping system Installation and hydrostatic testing shall be in accordance with AWWA C600 and AWWA C651.
TUF Grip 4 to 12 restraints shall meet the requirements of ASTM F1674, current revision.
*Tyler Union Waterworks Contact Information*
Tyler: 11910 CR 492 Tyler, Texas 75706 (800) 527-8478
th
Anniston: 1501 W 17 St. Anniston, AL 36201 (800) 226-7601
Corona: 1001 El Camino Ave. Corona, CA 92879 (866) 527-8471
89
1.
2.
3.
4.
Insure the beveled pipe end to be joined and mechanical joint socket are clean and free of debris.
Lubricate the pipe end and exterior plus the inside surface of gasket with joint lubricant that meets the
requirements of AWWA C111. Now place the MJ gasket over the plain beveled end of the pipe with the narrow edge
of the tapered gasket toward the beveled end of the pipe to be restrained.
Fully insert the pipe end into the MJ socket pipe landing. Keeping the pipe straight, slide/push the gasket firmly and
evenly into the MJ socket recess. **NOTE: For IPS diameter pipe use of an MJ transition gasket is required.
Place the two halves of the red TUF Grip around the pipe with the compression lip extension toward the MJ socket.
Join the two restraint halves together with two T-Head bolts. Use only T-Head bolts, nuts, and gasket that meet
AWWA C111 requirements.
Steps:5
5.
6.
7.
8.
9.
Step:3 and 4
Steps:6 and 7
Steps:8 and 9
With the two T-Head bolts inserted through the restraint, push the TUF Grip lip extension evenly against the thick
side of the MJ gasket. With the TUF grip restraint against the gasket, the remaining T-Head bolts are inserted with
the T-Head against the back of the MJ fitting bolt flange. Install two additional T-Head bolts with nuts and hand
tighten to secure the restraint to the fitting.
With the restraint secured to the fitting, remove the original assembly T-Head bolts and reinsert with the T-Head
against the back of the MJ fitting bolt flange. Making sure the TUF Grip is centered around the pipes wall, hand
tighten all the remaining T-Head bolts and nuts. If joint deflection is needed, only deflect the pipe in joint after hand
tightening of all nuts is completed. Maximum joint deflection is 3 when pipe and fitting dimensions are nominal.
Using a wrench, tighten the nuts on the T-Head bolts a few turns at a time in an alternating or star pattern. Maintain
equal spacing between the TUF Grip bolt flange and the bolt flange of the MJ socket as the gasket is compressed.
The T-Head bolt and nut torque requirement is 75-90 ft.-lbs. for 4-12 restraints. DO NOT OVER-TORQUE!
Hand-tighten the torque limiting nut attached to the TUF Grip wedge assemblies in a clockwise direction with an
alternating or star pattern until all gripping wedges are in contact with the pipe wall. Rotational direction of torque
nut is indicated by a recessed arrow on the face of the nut. With a wrench, continue to tighten each torque nut
turn in an alternating or star pattern until all torque limiting nuts twist off. NEVER tighten a torque limiting nut more
than turn without turning the remaining torque nuts an equal amount! **NOTE: For IPS applications, ensure step
7 is complete before engaging the wedges. Failure to comply will result in excessive pipe wall deflection and torque
nuts will not twist off as designed.
When all torque limiting nuts twist off, the mechanical joint and restraint assembly are complete.
*Tyler Union Waterworks Contact Information*
Tyler: 11910 CR 492 Tyler, Texas 75706 (800) 527-8478
th
Anniston: 1501 W 17 St. Anniston, AL 36201 (800) 226-7601
Corona: 1001 El Camino Ave. Corona, CA 92879 (866) 527-8471
90
FOR:
AWWAC900 (4 12) and AWWAC905 (14 36) PVC Pipe to Pipe Restrainer (Bell to Pipe Spigot)
Available in sizes 4 through 36 (Clamps for IPS PVC pipe available in 4 12 only)
Restraints rated at the listed pressure on the PVC pipe with a 2:1 safety factor
Full 360 contact, No pipe distortion or point loading
To ease installation, restraints and pipe can be assembled outside the trench
Connecting rods, hex nuts, T-head bolts consist of low alloy high strength steel and comply with
applicable requirements of ANSI/AWWA C111/A21.11
Clamping bolts are SAE Grade 5 and comply with applicable requirements of ANSI/AWWA C111/A21.11
For easy identification, IPS pipe diameter clamps are GREY and DI pipe diameter clamps are BLACK
SAMPLE SPECIFICATIONS:
All sizes of clamps are made of high strength grade 65-45-12 ductile iron in accordance with the
requirements and specifications of ASTM A536. Clamps provide full 360 degree contact with the PVC
pipe and internal serrations are machined to exact tolerances. Restrainers approved per applicable
requirements of ASTM F1674, current revisions apply. The 3000PP kits include, 1) 2 each 3000C
restrainers, 2) hex head bolts and hex nuts for restrainer assembly, and 3) threaded restrainer
connecting rods with hex nuts.
4 to 12 Assembly
Nominal
Size
Pipe O.D.
Part Number
4
4.80
462422
6
6.90
462439
8
9.05
462446
10
11.10
462453
12
13.20
462460
14
15.30
488033
16
17.40
488040
18
19.50
488057
20
21.60
488064
24
25.80
488071
30
32.00
498599
36
38.30
498605
*Note: Approximate dimension
14 to 36 Assembly
Part Number
462477
462484
462491
462507
462514
N/A
N/A
N/A
N/A
N/A
N/A
N/A
*A
9.12
11.12
14.74
16.81
19.45
22.54
24.66
26.64
28.76
33.98
40.90
48.00
1.12
1.12
1.25
1.38
1.38
4.00
4.00
5.06
5.06
5.20
10.00
10.00
C
MAX.
Qty.
12.0
13.0
15.0
16.0
18.0
24.0
28.0
28.0
34.0
34.0
34.0
34.0
Restraint Rods
Connecting
Qty.
2
2
2
4
4
6
6
8
8
12
12
12
Size
3/4 X 17
3/4 X 17
3/4 X 17
3/4 X 24
3/4 X 24
3/4 X 30
3/4 X 30
3/4 X 30
3/4 X 36
3/4 X 36
1 X 40
1 X 40
Size
5/8 X 3.5
5/8 X 3.5
3/4 X 5
7/8 X 5
7/8 X 5
7/8 X 6.5
7/8 X 6.5
1X8
1-1/8 X 8.5
1-1/8 X 8.5
1-1/8 X 8.5
1-1/8 X 8.5
Torq
100
100
150
150
150
150
150
175
200
225
250
250
~WT
LBS.
15
19
31
51
55
138
148
207
265
407
605
670
91
Tyler Union Waterworks Contact Information
Tyler: 11910 CR 492 Tyler, Texas 75706 (800) 527-8478
Elmira: 1021 East Water Elmira, NY 14902
Anniston: 1501 W 17th St. Anniston, AL 36201 (800) 226-7601
New Lenox: 2200 West Haven New Lenox, IL 60451
Corona: 1001 El Camino Ave. Corona, CA 92879 (866) 527-8471
Portland: 6204 N. Marine Dr. Portland, OR 97203
www.tylerunion.com
Figure 2
Figure 3
Figure 4
Step (1): Assemble pipe per Figure 1 making sure the spigot end of the pipe is fully seated in the bell end of the pipe.
Step (2): Assemble first restrainer on the bell end of the pipe joint and using one of the connecting rods (included) as a guide, mark
the location for the spigot restrainer per Figure 2.
Step (3): Assemble the spigot restrainer leaving sufficient threads on each end of the connecting rod to fully install washer and fully
engage nut per Figure 3. Tighten the restrainer clamp assembly bolts on each side evenly to the recommended torque
maintaining even gaps between the clamp pads.
Step (4): Connect both restrainers per Figure 4 utilizing the threaded restrainer connecting rods provided. Place a flat washer over
onto connecting rods and against the restrainer ear. Install hex nuts on the connecting rods and hand tighten all hex nuts
to hand tight plus one full turn. Do not over tighten retaining hex nuts. Use additional hex nuts (not included) on the inside
of restrainer ears if joint is expected to contract.
The hex head bolt and hex nut *torque recommended for assembly of the 3000C restrainers is as provided
NOTE: For best results use the lower end of the recommended torque range for DR 41 and DR 51 PVC pipe
*4 6 100 ft. lbs. | 8 12 150 ft. lbs. | 14 16 150 200 ft. lbs.
18 175 225 ft. lbs. | 20 200 250 ft. lbs. | 24 225 275 ft. lbs. | 30 36 - 250 300 ft. lbs.
92
FOR:
PVC Pipe Stop for AWWAC900 (4 12) and AWWAC905 (14 16) PVC Pipe
Note: IPS PVC Pipe Stop available for sizes 4 12
USE:
Improper installation such as over-insertion of a PVC pipe to pipe joint can cause damage to pipe bells, reduction in joint
deflection, and cause leaks. The 3000PS when properly installed will allow joint to be installed and operate to design
specifications.
SAMPLE SPECIFICATIONS:
Ring support clamps are made of high strength grade 65-45-12 ductile iron in accordance with the requirements and
specifications of ASTM A536. Clamps provide full 360 degree contact with the PVC pipe and internal serrations are
machined to exact tolerances. Serrated clamps shall be used to grip the pipe and be capable of being installed bidirectional. The rubber bell stop ring is NSF-61 approved.
4 to 12 Assembly
Nominal
Size
4
6
8
10
12
14
16
Pipe O.D.
4.80
6.90
9.05
11.10
13.20
15.30
17.40
Part Number
Pipe O.D.
Part Number
538981
4.50
CALL
538998
6.63
CALL
539001
8.63
CALL
538967
10.75
CALL
538974
12.75
CALL
539018
N/A
N/A
539025
N/A
N/A
*Note: Approximate dimension
**Note: Red Dimensions are for IPS Pipe Bell Stop Rings.
Figure 1
Figure 2
14 to 16 Assembly
*A
9.12
11.12
14.74
16.81
19.45
22.54
24.66
1.12
1.12
1.25
1.38
1.38
4.00
4.00
**D
DIOD/IPS
Qty
Size
Torque (ft.-lbs.)
2.34 /2.38
2.
5/8 X 3.5
100
2.34 /2.37
2
5/8 X 3.5
100
2.47 /2.52
2
3/4 X 5
150
2.60 /2.64
2
7/8 X 5
150
2.60 /2.66
2
7/8 X 5
150
5.22 /N/A
4
7/8 X 6.5
150
5.22 /N/A
4
7/8 X 6.5
150
**Note: IPS dimensions for pipe bell stop rings are in red
Figure 3
Clamp
Weight
Kit
Weight
4.5 lbs.
6.5 lbs.
10.0 lbs.
18.0 lbs.
21.0 lbs.
43.5 lbs.
46.0 lbs.
5.5 lbs.
7.5 lbs.
12.0 lbs.
20.0 lbs.
22.5 lbs.
45.0 lbs.
48.0 lbs.
Figure 4
Step (1): Lube the inside diameter of the Bell Stop Ring and slide the ring onto the Plain end of the PVC pipe. The angled side of the gasket
must face away from the end of the pipe to be assembled per figure 1.
Step (2): Align the Bell Stop Ring with the pipe manufacturers reference line per figure 2. If the pipe has been cut or the line is not visible,
mark a line at the pipe manufacturers recommended distance.
Step (3): Assemble the 3000C Ring Support Clamp at the end of the Bell Stop Ring per figure 3. Tighten the ring support Clamping Bolts on each
side evenly, maintaining equal spacing between the clamp ring support pads on both sides. (4 6 100 ft. lbs., 8 12 150 ft. lbs.)
Step (4): Complete PVC pipe joint assembly per manufacturers assembly instructions.
93
FOR:
Restraining AWWAC900 (4 12) and AWWAC905 (*14 36) PVC pipe to mechanical joint fittings
Note: IPS 3000MJ available for sizes 4 12
Note: *4 16 provided in boxed kits. Sizes larger than 16 will be provided with accessories kitted
separate from the restraint and gland.
SAMPLE SPECIFICATIONS:
All sizes of clamps are made of high strength grade 65-45-12 ductile iron in accordance with the requirements
and specifications of ASTM A536. Clamps provide full 360 degree contact with the PVC pipe and internal
serrations are machined to exact tolerances. Restrainers approved per applicable requirements of ASTM F1674,
current revisions apply. The 3000MJ kits include, 1) 1 each 3000C restrainer, 2) hex head clamping bolts and
nuts for restrainer assembly, 3) threaded restrainer connecting rods and hex nuts, 4) 1 each AWWA C153
mechanical joint gland, 5) 1 each NSF approved MJ gasket, and 6) all T-head bolts and hex nuts for gland
assembly.
4 to 12 Assembly
Nominal
Size
Pipe O.D.
DIOD Part No.
4
4.80
462576
6
6.90
462583
8
9.05
462590
10
11.10
462606
12
13.20
462613
14
15.30
CALL
16
17.40
CALL
18
19.50
CALL
20
21.60
CALL
24
25.80
CALL
30
32.00
CALL
36
38.30
CALL
*Note: Approximate dimension
14 to 36 Assembly
*A
9.12
11.12
14.74
16.81
19.45
22.54
24.66
26.64
28.76
33.98
40.90
48.00
1.12
1.12
1.25
1.38
1.38
4.00
4.00
5.06
5.06
5.20
10.00
10.00
C
MAX.
Qty.
6.00
6.00
6.00
6.00
6.00
15.00
15.00
15.00
22.00
22.00
22.00
22.00
Restraint Rods
Connecting
Qty.
2
2
2
4
4
6
6
8
8
12
12
12
Size
3/4 X 7
3/4 X 7
3/4 X 7
3/4 X 7
3/4 X 7
3/4 X 17
3/4 X 17
3/4 X 17
3/4 X 24
3/4 X 24
1 X 24
1 X 24
Size
5/8 X 3.5
5/8 X 3.5
3/4 X 5
7/8 X 5
7/8 X 5
7/8 X 6.5
7/8 X 6.5
1X8
1-1/8 X 8.5
1-1/8 X 8.5
1-1/8 X 8.5
1-1/8 X 8.5
Kit
(lbs.)
Torq
100
100
150
150
150
150
150
175
200
225
250
250
94
Figure 2
Figure 3
Figure 4
Figure 5
Step (1): Assemble the mechanical joint, installing gasket, gland, and T-head bolts per AWWA C600 standard, leave out the T-head
assembled.
Step (3): Assemble restrainer per Figure 3, leaving sufficient threads on the end of the T-head bolt to fully engage nut.
Step (4): Tighten the restrainer clamp assembly bolts on each side evenly to the recommended torque maintaining even gaps
installing a hex nut between the gland and restrainer. Tighten the hex nut up to gland per AWWA C600 standard. Tighten
the second hex nut up to the restrainer as show in Figure 5. Use additional hex nuts (not included) on the inside of the
restrainer ear if joint is expected to contract.
Figure 2
Figure 3
Figure 4
Step (1): Assemble the mechanical joint, installing gasket, gland, and T-head bolts per AWWA C600 standard, leave out the T-head
assembled.
Step (3): Assemble restrainer per Figure 3, leaving sufficient threads on the end of the connecting rod to fully install washer and fully
engage hex nut. Tighten the restrainer clamp assembly bolts on each side evenly to the recommended torque maintaining
even gaps between the clamp pads. (14 16 150 200 ft lbs., 18 - 175 - 225 ft. lbs., 20 - 200 - 250 ft. lbs., 24 - 225 275 ft. lbs., 30 250 - 300 ft. lbs., and 36 - 250 - 300 ft. lbs.)
Step (4): Connect restrainer to fitting per Figure 4. Inserting the rods through the restrainer ears(rod and 3 hex nuts provided for
each ear), gland, and fitting bolt hole. Install one hex nut behind fitting bell, one hex nut against the gland and one hex nut
behind the restrainer ear against the washer. Tighten hex nut up to gland per AWWA C600 standard. Use additional hex
nuts (not included) on the inside of the restrainer ear if joint is expected to contract.
95
Mechanical and Push-On joint fittings with flanged branches are rated for working pressure of 250
PSI. Flange fittings 24 inches and smaller may be rated for 350 PSI working pressure with the use of
special flange gaskets. For 350 PSI flange joint applications we recommend the use of annular ring
type gasket or comparable. AWWA C153 MJ and Push on joint wyes larger than 12 are not
pressure; contact Tyler Union for the allowable pressure ratings for 14 and larger wyes.
Tyler Union Waterworks ANSI/AWWA C110/A21.10 and ANSI/AWWA C153/A21.53 ductile iron Mechanical joint fittings and
ANSI/AWWA C153/A21.53-06 (manufacturers standards) Push-On joint fittings when installed per AWWA C600/651 are rated for a *maximum 5
degrees of deflection for 3 inch through 12 inch fittings and a *maximum 3 degrees of deflection for 14 inch through 48 inch fittings.
*Note : The total joint deflection is determined by the O.D. of the pipe and the I.D. of the fitting. When both the pipe and the
fitting are at nominal; the joint deflection will be approximately 50% of the maximum listed.
Tyler Union Waterworks coated and/or cement lined Potable water ductile iron fittings meet all the applicable terms and requirements of
ANSI/AWWA C116/A21.16, ANSI/AWWA C104/A21.4, and AWWA C550. Potable water products manufactured and distributed by Tyler Union
Waterworks are National Sanitation Foundation NSF 61, NSF-372, and Annex G compliant. Current revisions apply for each noted standard.
Tyler Union Waterworks Valve and Service boxes are produced in accordance with and meet all applicable terms and provisions of
ASTM-A48. Cast iron Service and Valve box products when properly selected and installed per the guidelines provided by AWWA M44 (Manual of
Water Supply Practices) will provide accessibility for testing and maintenance of a water supply system and will meet the Wheel load designation as
provided by the American Association of State Highway Transportation Officials (AASHTO).
Tyler Union Waterworks Mechanical joint fittings, Glands, T-Head bolts, and Nuts are produced in accordance with and meet all applicable
terms and provisions of ANSI/AWWA C111/A21.11. Tyler Union Mechanical and Push-On joint gaskets are produced in accordance with and meet
all applicable terms and provisions of ANSI/AWWA C111/A21.11. Tyler Union manufacturers standard design Mechanical and Push-On joint
Transition gaskets are produced in accordance with and will meet all applicable terms and provisions of ANSI/AWWA C111/A21.11.
All applicable tests have been performed and results maintained with all materials supplied being of the same quality, manufacture, and
make as those tested.
Sincerely,
Project Name:
Roger Dunning
Roger Dunning
Technical Support Manager
Tyler Union Waterworks
Email: roger.dunning@tylerunion.com
Tel.: (800) 527-8478
Project Material:
Product Supplier:
Contractor:
File:
COC TU Products
98
1.
ENTIRE AGREEMENT. McWane, Inc. and its divisions and subsidiaries (the Seller) agrees to sell the goods
covered herein (Goods) to Buyer on the following terms and conditions of sale (the Terms and Conditions) which
supersede any other or inconsistent terms of Buyer. The Terms and Conditions and the order or other contract
documents to which they are attached constitute the entire agreement between the parties with respect to the Goods (the
Agreement). All references by Seller to Buyers specifications and similar requirements are only to describe the Goods
and work covered hereby and no warranties or other terms will have any force or effect. Neither this Agreement, nor any
modification, amendment or waiver to it, nor any cancellation, change or return of any order under it, will be binding on
Seller until agreed in writing by Sellers authorized representative. No representation, promise or term not set forth herein
has been or may be relied upon by Buyer, and any terms not contained in this Agreement are expressly objected to and
rejected. Acceptance of orders, whether oral or written, and/or delivery by Buyer is based on the express condition that
Buyer agrees to all of these Terms and Conditions.
2.
QUOTATIONS. Where this Agreement is used by Seller to place a bid, the quotation stated herein is for
prompt acceptance and Seller may change and/or withdraw without notice. Prompt acceptance by Buyer of all quotations
is a material term of the bid and any subsequent agreement. In cases where freight allowance is included in the quotation,
Buyer is liable for any rate increase and/or additional expense over the calculated allowance resulting from compliance with
Buyers shipping instructions.
3. DELIVERY. All prices are EXW (Ex-Works)(per Incoterms 2010), unless otherwise specified by Seller in writing. All
shipping dates are approximate, and any time period indicated for a shipment will not commence until receipt at
Sellers plant of complete manufacturing, shipping, and credit information. Acceptance of shipment by designated
shipper, allocation of Goods to Buyer at premises other than Sellers, delivery to Buyers representative or designee or
mailing of an invoice to Buyer, whichever first occurs, will constitute tender of delivery and title will pass to Buyer, subject
to Sellers right of stoppage in transit and to any interest of Seller reserved to secure Buyers payment or performance,
irrespective of any freight allowance or prepayment of freight. In the case of Goods held subject to Buyers instructions,
Goods for which Buyer has failed to supply shipping instructions, or in any case where Seller, in its sole discretion,
determines that any part of the Goods should be held for Buyers account, Seller may invoice for the Goods and Buyer
agrees to make payment at the maturity of the invoice rendered. Goods invoiced and held at any location for whatever
reason will be at Buyers risk and Seller may charge for (but is not obligated to carry) insurance, storage and other
expenses incident to such delay at their prevailing rates. Partial deliveries shall be accepted by Buyer and paid for at
Agreement prices and terms. When Buyer has declared or manifested an intention not to accept delivery, no tender shall be
necessary but Seller may, at its option, give notice in writing to Buyer that Seller is ready and willing to deliver and such
notice shall constitute a valid tender of delivery.
Buyer must report any shortages in shipments within three (3) days of
receipt of the initial shipment.
4.
LOSS OR DAMAGE IN TRANSIT. Buyer may not make any deduction from any payment due hereunder by
reason of loss or damage to Goods in transit. Upon Buyers written request, Seller, in its sole discretion, may agree as a
service to Buyer to process Buyers claim against the carrier for any loss or damage in transit, provided that Seller
receives such claim within five (5) days of the delivery of the Goods. Any such claims must be accompanied by a delivery
receipt, signed by carriers agent at time of delivery, on which receipt the loss or damage has been noted, or such claims
will be waived.
5.
TERMS OF PAYMENT. Terms are stated on Sellers order or invoice document. Seller may make partial
shipments and payment for that portion shall be due as provided on Sellers order or invoice document based on time of
shipment. If, at any time or for any reason, Seller has cause to question Buyers ability to perform, Seller may
demand such assurances of Buyers performance as Seller deems necessary in its discretion, including payment in
advance for all shipments. If Buyer fails within ten (10) days of Sellers demand to provide Seller with such assurance,
Seller may suspend its performance, cancel any order then outstanding, receive reimbursement for its reasonable and
proper cancellation charges and collect, without limitation, any sums due and owing, its reasonable cancellation
charges and all damages resulting from Buyers default.
In t he e v e n t of Buyers bankruptcy or insolvency, or in
the event of any proceeding brought against Buyer, voluntarily or involuntarily, under bankruptcy or any insolvency laws,
Seller may cancel any order then outstanding at any time and receive reimbursement for its reasonable and proper
cancellation charges. If Buyer fails to make payment for Goods when due, Buyers account will be deemed delinquent and
Buyer will be liable to Seller for a service charge of eighteen percent (18%) per annum or the maximum allowed by law,
whichever is greater, on any unpaid amount; provided that, in addition to the foregoing, Seller may also suspend its
performance, cancel any order then outstanding, receive reimbursement for its reasonable and proper cancellation charges
and to collect, without limitation, any sums due and owing, its reasonable cancellation charges and all damages resulting
from Buyers default. Buyer will be liable to Seller for all costs and expenses of collection, including court costs and
reasonable attorneys fees.
6/17/2013
6/17/2013
6/17/2013
CONSTRUCTION. No provision of this Agreement may be construed against the Seller as the drafting party.
6/17/2013
www.tylerunion.com
SEARCH INVENTORY for all fittings, accessories,
valve boxes, companion flanges and other products
in stock, 24 hours a day, 7 days a week.