Professional Documents
Culture Documents
Milwaukee Impact Parts 2650-20 - (SER - B55A)
Milwaukee Impact Parts 2650-20 - (SER - B55A)
54-26-2620
00
EXAMPLE:
0 Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
2650-20
STARTING
SERIAL NO.
B55A
REVISED BULLETIN
DATE
Aug. 2008
WIRING INSTRUCTION
2
3
21 22 23 24 25 26
19 20
27 28 29 30 31 32 33
9 10
11 13
15
45
43 44
46
37
36 35
65
FIG.
36 37 38 39 40 41
66 35
42 43 44 45 46 47 65
FIG.
1
2
3
4
5
6
7
8
9
10
11
13
15
16
17
19
20
21
22
23
24
25
26
27
28
29
30
31
PART NO.
31-44-2430
----------------------------42-52-0062
45-24-0300
45-30-0250
42-70-5150
40-50-1090
----------------------------23-66-0426
----------------------------16-01-3010
18-01-3010
14-30-0920
44-66-1600
32-65-0230
44-90-0950
02-04-1890
45-88-1970
44-60-1950
32-62-0375
42-50-0450
02-02-0180
45-88-2050
40-50-1105
45-88-2010
DESCRIPTION OF PART
Handle Assembly
Left Handle Half
Right Handle Half
End Cap
Forward / Reverse Shuttle
Rubber Slug
Belt Hook
Spring
Contact Block
Switch
Switch/Brush Card Assembly
LED Assembly
Brush Card Assembly
Service Armature Assembly
Service Field
Gear Box Assembly
Rear Case
Ring Gear
Retaining Ring
Ball Bearing
Washer
Pin
Planet Gear
Cam Shaft
3/16" Steel Ball
Washer
Compression Spring
Washer
NO. REQ.
(1)
(1)
(1)
(1)
(1)
(8)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(2)
(2)
(1)
(2)
(1)
(1)
(1)
FIG.
32
33
35
36
37
38
39
40
41
42
43
44
45
46
47
55
56
57
59
60
65
66
LUBRICATION
(Type 'Z' Grease, No. 49-08-7655):
21,26 Lightly coat the I.D. of the Ring Gear (21) and the
center of the two Planet Gears (26) with grease.
27
Place a dab of grease in the ball grooves of the
Cam Shaft (27).
35,36,37 Lightly coat the front washer surface of Anvil (36)
with grease, place a dab in the Ball holes of Anvil
and in the Needle Bearing inside the Anvil.
45
Coat outside grooves of Bushing (45) with grease.
PART NO.
02-02-0165
44-82-0800
--------------42-06-0560
02-02-0170
45-22-0825
40-50-1470
45-88-1880
34-60-0725
45-88-2025
28-50-0900
------------------------------------------06-82-7010
06-82-6350
06-82-7336
06-82-5275
12-20-2650
10-20-2695
--------------14-30-0950
42-55-2650
DESCRIPTION OF PART
NO. REQ.
3.0mm Steel Ball
(30)
Hammer
(1)
Needle Bearing
(1)
1/4" Hex Drive Anvil Assembly
(1)
3.5mm Steel Ball
(2)
Sleeve
(1)
Spring
(1)
Washer
(1)
Retaining Ring
(1)
Front Washer
(1)
Front Case Sub-Assembly
(1)
Retaining Ring
(1)
Bushing
(1)
Front Case
(1)
8-18 x 24 Pan Hd. Screw
(4)
M3 Pan Hd. T-10 Screw
(7)
M3 Pan Hd. T-10 Screw
(4)
6-32 x 5/16" Slt. Pan Hd. T-15 Screw (1)
Service Nameplate Kit
(1)
Warning Label
(1)
5mm Steel Ball
(1)
Front Case Assembly
(1)
Carrying Case (Not Shown)
(1)
MILWAUKEE ELECTRIC TOOL CORPORATION
13135 W. Lisbon Road, Brookfield, WI 53005
Drwg. 1
FIELD
BRUSH CARD
ASSEMBLY
LED
ASSEMBLY
1
BLACK
BE CAREFUL AND AVOID
PINCHING WIRES BETWEEN
HANDLE HALVES WHEN
ASSEMBLING.
2
RED
3
GREEN
SWITCH
GRAY
RED
RED
6
BLACK
BLACK
7
WHITE
CONTACT
BLOCK
WIRING SPECIFICATIONS
Wire
No.
1
2
3
4
5
6
7
8
9
Wire
Color
Black
Red
Green
Gray
Red
Black
White
Black
Red
Origin or
Gauge
-------------------------------------
Length
-------------------------------------