M1.1/3/EN/2
Return Air Grilles
Type AR * AE
TROZ*
TECHNIK
‘TROX Malaysia Sdn. Bhd. Telephone + 606-678 8188
20 Persiaran Bunga Tanjung 4 Tolofax + 606-678 6288 / 388
‘Senawang Land Industrial Park E-mail enquiry@troxmal.com.my
70400 Seremban ‘wwnw.troxapo.com
Negeri Sembilan Darul Khusus
MalaysiaContents - Description - Construction
Description__________2 Technical Data, Effective inlet Areas.
Construction 2 Technical Data for Type ‘AR’
Materials. 3. Technical Data for Type ‘AE™
Standard Sizes 3 Order Details,
Description Type AE
‘These Type ‘AR’ and ‘AE’ grilles are suitable This type of return air grille has fixed square
for installation to walls or directly to ductwork Pattern core with a 32 mm wide border
for return air application only. complete with counter punched holes for front,
sorew fixing (ie., visible)
Construction: Note: Flat border identical to TROX Type ‘AH’
grille can be provided for the Type ‘AR’ and
Type AR ‘AE' grilles if required. These derivative grilles
are known as Type 'F- AR and F- AE’ grilles,
This type of return air grille has fixed horizontal fespectively
blades with angled profile and a 32 mm wide
border complete with counter punched holes
for front screw fixing (i.e., visible),
Type AR
Wha
1334
ye
ag
a8 4 =
ag ]
SF
zi fb
HIL
GQ IP222PPPP??
22
. o Type AE
We
ais}
HIL
lf 13
H+22/L+22
H+45/L+45
a : a.
Duct Opening with Sub-frame (for spring
clip and latch fixings only).
‘The required duct opening with sub-frame,
for spring clip (P11) or latch fixing (S11) is:
L+6mm and H+ 6mm,
For detail, refer to Catalogue (Ref. M
1/1 AIEN/2) for “Grilles / Linear Grilles’ on
page 27.Table 1: Standard Sizes,
[en
Lay
150,
200
250.
300
360
400.
a0
S00
350
500
650
700
750
200
350
300
250
000
7060
100
160
#200
1250
100
150
Lx H (mm)
200
250
Materials - Standard Sizes
300
Materials:
Both types of ‘AR’ and ‘AE grilles are made
from extruded aluminium sections in matt white
powder coating to RAL 9010 as standard
supply. The rear assembly for both types of
grilles is made from formed sheet steel and,
painted in black to RAL 9005. The installation
Sub-frame is made from galvanized sheet steel
This will be provided in loose sections to be
installed by others.
aso | 400 | 450 | 500
Note: The’ ana 'H’clmensions as given above represent the connecting duct size or opening size inthe wall where the
gilli intended to be installedTechnical Data
Table 2: Effective Inlet Area, Act (m?)
wel ens
it Fea
Peal AR AE pela AR AE
(mm) (mm)
= 500 0.083
J 600 0.077
2 ea oye
ce mee =
= & oe
a he 38
@ 600 x 600 0.108
= = Be
oo 1000 O18
Determination of Volume Flow Rate:
= oa cee Volume tow rate can be determined by measuring
aa 2.8 ors the air velocity using a rotating vane anemometer.
ee oo et Velocty measurement should be taken aorose the
800, 0.053. 03120 grille face, using the vane anemometer, placed at
2 oe oe Squldstance to cover the entre face area of the
i oa te gill, Then sum up the veloty measurements and
determine the mean velcly (16, V mar) across the
sis | ar oa gfe ace
00 019 on08 The fiow rate can be calculated using either one of
ea 0.987 ous the formulae below;
se oss cass W (Wis) = v mean (m/s) x Aett (m2) x f* x 1000
V (m4/h) = V moan (mis) x Aott (m2) x f * x 3600
a Bowe Shee “Note: Where 'f ’is the correction factor (Refer to
soa oess gags Table 4 below).
pot oes ore Table 3: Correction for Act
‘7200 one LwalLwne | -13 40 | 7 3 +3 | +8
27777)
Table 4: Correction Factor, f
‘Type f
AR 32
AE 16rosso dop ink Pin Pa
Technical Data - Nomenclature
Type ‘AR' Grille
Example:
Data given as;
Volume flow rate - 195 lis
Grille selected: Type AR-AG/ 800 x 150
Effective inlet area, Act: 0.029m? (see Table 2)
‘Assuming that damper setting is 100% (Le.
fully open);
Effective velocity, vert=W/ (Ae x 1000)
vert = 195 / (0.028 x 1000)
vett= 6.7 mis.
From Graph 1 below;
Lwa-= 37 dB (A); Lwno= NC 31 and
Apt= 21 Pa
Using the correction for Actin Table 3 on
page 4:
Lwa: 37-6 = 31 dB (A)
Lwne: 31-6 = NC 25
Graph 1: Sound Power Levels and Pressure
Drop
Graph 2: Octave Band Sound Power Levels
(Damper setting at 100% open)
A
pe