Professional Documents
Culture Documents
Blm
REFERANCE GEOMETRY
ARA UBUU KOMUTLARI
280
REFERANCE
GEOMETRY
Referans Geometri
Ara ubuu
Referance Geometry
Kayar men
InserthReferance Geometry
Bir kat veya bir yzeyin biimi veya eklini Referans Geometri tanmlar. Planes (Dzlemler), Axes
(Eksenler), Coordinate Systems (Koordinat sistemleri), points (noktalar) ve 3D (3 Boyut) taslak
erilerden oluur.
281
PLANE
Ara ubuu
Referance GeometryhPlane
Dzlem Oluturma
Kayar men
InserthReferance GeometryhPlane
282
283
3 noktadan geen yeni bir dzlem oluturarak, yeni dzlemden kat ekleme;
284
Not: Dzlemleri fare sa tuuna tklayarak hide seildiinde gizlenebilir. Tekrar grlmesi istendiinde
fare sa tuuna basp show seildiinde dzlem grntlenir.
285
286
287
At Angle (Al):
Bir yzeye veya dzleme belirli bir ada bir doru tasla, bir kenar veya bir eksene akk yeni bir
dzlem oluturulabilir.
Dzlem yzey ve ayn yzeye bal kenar seilerek a girilir. Oluan yeni dzlemden kat
ekleme/karma;
288
289
Offset (Ofset):
Bir dzlem veya yzeye gre verilen paralel bir mesafede yeni bir dzlem oluturulabilir.
290
291
292
293
294
295
296
AXIS
Ara ubuu
Referance GeometryhAxis
Referans Ekseni
Kayar men
InserthReferance GeometryhAxis
One Line/Edge/Axis (Bir Doru/Kenar/Eksen): Bir kat modelin kenar, bir doru ve mevcut
eksen zerine yerletirilebilir. Ayrca silindirik ksmlara geici eksen yerletirmek iin;
Kayar Men: ViewhTemporary Axes
Seili duruma getirilerek paralar zerinde eksen grntlenir. Seili durum kaldrldnda eksenler yok
olur.
297
Two Points/Vertices: ki nokta veya iki ke arasnda eksen oluturulur. Ayrca kenar veya
dorularn orta noktalar (midpoints) da seilerek eksen oluturulur.
298
299
Point and Surface: Bir kenar nokta veya bir dorunun orta noktas ile, bir dzlem veya
yzey arasnda eksen oluturulur. Eer yzey dzlemsel olmayan bir yzeyse yzey zerindeki bir
nokta seilmelidir. Oluan eksen seilen yzeye diktir ve seilen noktadan geer.
zellik yneticisindeki eksen zerine fare sa tuu ile tklanr. Listelenen komutlardan Hide (Gizle) veya
Show (Grntle) seenekleri seilerek eksenler tek olarak gizlenir veya grntlenir.
300
COORDINATE
SYSTEM
Koordinat Sistemi
Ara ubuu
Referance GeometryhCoordinate
System
Kayar men
InserthReferance Geometryh
Coordinate System
Mevcut koordinat sistemini dzenlemek veya para veya montaj resimlerine yeni bir koordinat sistemi
tanmlamak iin kullanlr.
Coordinate System zellik Yneticisinde Selections ksmnda;
Para veya montajlarda koordinat sisteminin merkezi (Orijin) iin, bir ke, kenarlarn orta
noktas yada bir nokta seilir ve diyalog kutusundaki Orijin ksmnda grntlenir.
X, Y, Z eksenlerinden birinin, hangi kenar zerinde ve paralelinde olmas istenirse, diyalog
kutusunda seilen eksen kutusu tklanr ve hemen arkasndan kenar seilir.
Eksen dorular iin nokta veya keler seilebilir.
301
POINT
Ara ubuu
Referance GeometryhPoint
Referans Noktalar
Oluturma
Kayar men
InserthReferance GeometryhPoint
302
Center Of Face: Dzlemsel veya dzlemsel olmayan yzeylerin arlk merkezinde bir
referans noktas oluturur.
303
Projection: Creates a reference point from one entity projected onto another. Select two
entities: the entity to project and the entity onto which to project. You can project points, endpoints of
curves and sketch segments, and vertices of solids and surfaces onto planes and faces (planar or nonplanar). The point is projected normal to the plane or face.
Along curve distance or multiple reference point: Kenarlar, eriler veya taslak
katmanlar boyunca bir referans noktas seti oluturur.
Enter the distance/percentage value according to distance: Set a distance or
percentage value to create the reference points. If the value is too large to create the specified
number of reference points, a message warns you to set a smaller value.
Distance: Creates the number of reference points spaced at the distance you set, starting
from the closest endpoint. The first reference point is created at this distance from the endpoint,
not on the endpoint.
Percentage: Creates the number of reference points spaced at the percentage you set,
starting from the closest endpoint. Percentage means percentage of the length of the selected
entity. For example, select a 100mm-long entity. If you set the number of reference points to 5
and the percentage to 10, the 5 reference points are spaced 10 percent of the total entity length
(or 10mm) apart from each other.
Evenly Distribute: Evenly distributes the number of reference points on the entity. If you
edit the number of reference points, the reference points update their position relative to the
starting endpoint.
Number of reference points: Set the number of reference points to create along the
selected entity. The reference points are created using the selected Distance, Percentage,
or Evenly Distribute option.
304