Professional Documents
Culture Documents
MB Installation Guide-Eu
MB Installation Guide-Eu
A. Installing an Intel CPU (skip this step if the motherboard has a built-in CPU)
A-1 Refer to the following instructions based on your CPU specifications:
Type A:
Lift the CPU socket lever and the metal load plate will be lifted as well.
a. If the protective socket cover is fastened on the CPU socket, remove
it first.
b. If the protective socket cover is fastened on the metal load plate, do
not remove it at this stage. The socket cover may pop off from the
load plate automatically during the process of re-engaging the lever
after you insert the CPU.
Type B:
Push lever A (closest to the "
" marking) down and away from the socket to release it. Then push
lever B (closest to the " " marking) down and away from the socket and lift it. Gently press lever A to
allow the load plate to rise. Open the load plate.
Lever A
Lever B
A-2 Hold the CPU with your thumb and index fingers. Align the CPU pin one marking (triangle) with the pin
one corner of the CPU socket (or you may align the CPU notches with the socket alignment keys) and
gently insert the CPU into position.
A-3 Once the CPU is properly inserted, replace the load plate and push the CPU socket lever back into its locked position.
Once the type B is properly inserted, carefully replace the load plate. Then secure lever B under its retention
tab. The socket cover may pop off from the load plate during the process of engaging the lever. Finally,
secure lever A under its retention tab to complete the installation of the CPU.
For detailed instructions on installing the CPU, please refer to the users manual.
-1-
English
The sequence of installation may differ depending on the type of case and devices used. The
installation instructions below apply to GIGABYTE's desktop systems and are for reference
only.
Refer to the user's manual included for detailed motherboard specifications.
Before installing the devices, make sure they are compliant with the connectors on your computer.
Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord
from the power outlet to prevent damage to the devices and the system components.
Place the computer system on a stable surface to prevent improper installation resulted from shaking.
English
B. Installing an AMD CPU (skip this step if the motherboard has a built-in CPU)
B-1 Completely raise the CPU socket lever. Align the CPU pin
one (small triangle marking) with the triangle marking on the
CPU socket and gently insert the CPU into the socket. Make
sure that the CPU pins fit perfectly into their holes.
B-2 Once the CPU is positioned into its socket, place one finger
down on the middle of the CPU, lowering the socket lever
and latching it into the fully locked position.
CPU Socket
Pin 1
Do not force the CPU into the CPU socket. The CPU cannot fit in if oriented incorrectly. Adjust the CPU
orientation if this occurs.
DO NOT touch socket contacts. To protect the CPU socket, always replace the protective socket cover
when the CPU is not installed.
Step
C-1 Before installing the CPU cooler, please first add a thin layer of
heat sink paste on the surface of the CPU. Then install the cooler
(refer to the installation manual for your CPU cooler).
C-2 Connect the CPU cooler cable to the CPU_FAN connector located
on the motherboard so that the cooler can properly function to
prevent the CPU from overheating.
Installing Memory
Note the orientation of the memory module. Spread the retaining clips at both ends
of the memory socket. Place the memory module on the socket. As indicated in the
picture on the left, place your fingers on the top edge of the memory, push down on
the memory and insert it vertically into the memory socket. The clips at both ends
of the socket will snap into place when the memory module is securely inserted.
Step
-2-
Step
Step
Before purchasing an expansion card, check the length of the card, making
sure it can fit into your case.
Make sure that the expansion card is fully seated in its slot.
One motherboard IDE connector can connect up to two IDE devices. Prior to installation, check the jumper
settings (master and slave) on your IDE devices.
If more than one hard drive is installed, enter system BIOS Setup to set the hard drive boot sequence.
-3-
English
Step
English
Step
7-1 Connect cables to internal connectors and headers on the motherboard, including IDE/SATA
connectors, and front panel audio, USB, IEEE 1394 headers, etc.
7-2 Attach the front panel module (differs depending on the case design, consisting of power
indicator, hard drive activity indicator, speakers, reset switch, power switch, etc.) from the case
to the front panel header (F_PANEL) on the motherboard.
Pin Assignments A:
+MSG- +PW-
+SPEAK-
Pin Assignments B:
+MSG- +PW-
+SPEAK-
20
19
+HD- -RES+
NC
(Note)
Step
+PWR-
The pin assignments for the front panel header may differ by model. Refer
to the motherboard user's manual for the actual pin assignments.
Connecting Peripherals
Back Panel of the Case
Power Supply
Power Switch
DVI-D Port
HDMI Port
D-Sub Port
eSATA Port
S/PDIF Connector
USB Ports
Audio Jacks
-4-
Die Installationsreihenfolge kann je nach Typ des verwendeten Gehuses sowie der verwendeten Gerte
variieren. Die folgenden Installationsanweisungen betreffen Desktop-Systeme von GIGABYTE und
dienen nur als Referenz.
Schlagen Sie bitte ausfhrliche technische Daten des Motherboards im beigelegten Benutzerhandbuch nach.
Stellen Sie vor der Installation von Gerten sicher, dass Ihre Gerte mit den Anschlssen Ihres Computers
kompatibel sind.
Schalten Sie immer vor dem Installieren die Gerte und Ihren Computer aus. Trennen Sie den Rechner vom
Stromnetz, um Schden an den Gerten und den Systemkomponenten zu vermeiden.
Stellen Sie das Computersystem auf eine stabile Unterlage, damit die Installation nicht durch Wackeln
beeintrchtigt wird.
A. Installieren einer Intel CPU (berspringen Sie diesen Schritt, wenn das Motherboard ber einen
eingebauten Prozessor verfgt)
A-1 Beachten Sie die folgenden Anweisungen basierend auf Ihren CPU-Spezifikationen:
Typ A:
Heben Sie den CPU-Sockelhebel an, dadurch hebt sich auch die
Metallladeplatte.
a. Falls die Sockelschutzabdeckung am CPU-Sockel befestigt ist,
entfernen Sie sie zunchst.
b. Falls die schtzende Sockelabdeckung an der Metallandruckplatte
befestigt ist, nehmen Sie sie jetzt noch nicht ab. Die Sockelabdeckung
kann sich beim Wiederanziehen des Hebels nach Einsetzen der CPU
von selbst lsen.
Typ B:
Drcken Sie Hebel A (der Markierung
am nchsten) nach unten und vom Sockel weg, um ihn
zu lsen. Drcken Sie dann Hebel B (der Markierung am nchsten) nach unten und vom Sockel
weg und heben Sie ihn an. Drcken Sie behutsam Hebel A, um den Deckrahmen anzuheben. ffnen
Sie den Deckrahmen.
Hebel A
Hebel B
A-2 Halten Sie die CPU mit Daumen und Zeigefinger. Richten Sie die (Dreieck-) Markierungen fr Pin 1 auf
der CPU und die Pin 1-Ecke des CPU-Sockels aufeinander aus. (Sie knnen ebenfalls die CPU-Kerben
auf die Ausrichtungsnasen des Sockels ausrichten.) Legen Sie dann vorsichtig die CPU in der richtigen
Position ein.
A-3 Legen Sie den Schutzrahmen wieder auf und stellen den CPU-Sockelhebel in seine Arretierposition zurck,
sobald die CPU richtig sitzt.
Bringen Sie den Deckrahmen nach dem ordnungsgemen Einsetzen der typ B vorsichtig wieder an.
Sichern Sie anschlieend Hebel B unter dessen Befestigungsnase. Die Sockelabdeckung kann sich beim
Bettigen des Hebels vom Deckrahmen lsen. Sichern Sie zuletzt Hebel A unter dessen Befestigungsnase,
um die Installation der CPU abzuschlieen.
Detaillierte Anweisungen zur CPU-Installation entnehmen Sie bitte der Bedienungsanleitung.
-1-
Deutsch
Schritt
B. Installieren einer AMD CPU (berspringen Sie diesen Schritt, wenn das Motherboard ber einen
eingebauten Prozessor verfgt)
Deutsch
CPU-Sockel-hebel
CPU-Sockel
Pin 1
Stecken Sie die CPU nicht mit Gewalt in den CPU-Sockel. Die CPU lsst sich nicht einpassen, wenn die
Ausrichtung falsch ist. ndern Sie in diesem Fall die Ausrichtung der CPU.
Berhren Sie NICHT die Sockelkontakte. Setzen Sie die Schutzabdeckung grundstzlich wieder auf,
wenn keine CPU installiert ist. Dies schtzt den Sockel vor Beschdigungen.
Schritt
Schritt
-2-
Schritt
I/O-Blende
Schritt
Schritt
Mit einem IDE-Anschluss am Motherboard knnen zwei IDE-Gerte verbunden werden. Prfen Sie bitte
vor der Installation die Jumpereinstellungen (Master und Slave) an Ihren IDE-Gerten.
Wenn mehr als eine Festplatte installiert ist, rufen Sie bitte das System-BIOS-Einstellungsprogramm auf
und stellen die Bootreihenfolge der Festplatten ein.
-3-
Deutsch
Entfernen Sie die ursprngliche E/A-Blende von der Rckseite des Gehuses und
ersetzen Sie sie durch die dem Motherboard beigelegte E/A-Blende. Legen Sie das
Motherboard in das Gehuse ein, wobei die E/A-Anschlsse auf die E/A-Blende
ausgerichtet werden mssen. Richten Sie die Schraubenlcher am Motherboard
auf die entsprechenden Befestigungslcher am Gehuse aus. Befestigen Sie das
Motherboard mit Schrauben am Gehuse.
Schritt
Deutsch
7-1 Verbinden Sie Kabel mit den entsprechenden Anschlssen und Sockel am Motherboard inklusive IDE/
SATA-Anschlsse, Front-Audio, USB, IEEE 1394 usw.
7-2 Verbinden Sie das Front Panel-Modul (es besteht je nach Gehusedesign aus einer Strom-LED, einer
Festplattenaktivitts-LED, einem Lautsprecher, einem Reset-Schalter, einem Stromschalter usw.) am
Gehuse mit dem Front Panel-Anschluss (F_PANEL) am Motherboard.
Pinbelegung A:
+MSG- +PW-
Pinbelegung B:
+SPEAK-
+MSG- +PW-
+SPEAK-
2
1
Front Panel-Anschluss
Schritt
+HD- -RES+
NC
+PWR-
MSG: Meldung-/Betrieb-/Ruhezustand-LED
PWR: Betriebsanzeige-LED
PW: Stromschalter
20 SPEAK: Lautsprecher
19 HD: Festplattenaktivitts-LED
RES: Reset-Schalter
CI: Gehuse offen-Anschluss
Hinweis: Die Pinbelegung der Frontblendenanschlsse kann je nach Modell abweichen. Bitte entnehmen Sie
die tatschliche Pinbelegung der jeweiligen Motherboard-Bedienungsanleitung.
Netzteil
Netzschalter
PS/2-Tastaturanschluss
Netzkabelanschluss
DVI-D-Port
PS/2-Mausanschluss
HDMI-Port
D-Sub-Anschluss
eSATA-Ports
S/PDIF-Anschluss
IEEE1394-Port
USB-Ports
Audioanschlsse
RJ-45 LAN-Port
Externe Grafikkarte
-4-
El proceso de instalacin puede variar dependiendo del tipo de CAJA y dispositivos utilizados. Las
instrucciones de instalacin que aparecen a continuacin son de aplicacin para ordenadores de escritorio
GIGABYTE y slo a modo de referencia.
Consulte el manual de usuario incluido para obtener especificaciones detalladas sobre la placa madre.
Antes de instalar los dispositivos, asegrese de que sean compatibles con los conectores del ordenador.
Antes de instalar los dispositivos, asegrese de apagar los dispositivos y el ordenador. Desconecte el cable
de alimentacin de la toma de corriente para evitar daar los dispositivos y los componentes del sistema.
Coloque la ordenador sobre una superficie estable para evitar que movimientos bruscos causen una
instalacin incorrecta.
Paso
A. Instalacin de un procesador Intel (omita este paso si la placa base tiene una CPU integrada)
La palanca A
La palanca B
A-2 Sostenga el procesador con los dedos pulgar e ndice. Alinee la marca de la clavija 1 del procesador
(tringulo) con la esquina de la clavija 1 del socket del procesador (o puede alinear las muescas del
procesador con las muescas de alineacin del socket) e inserte con cuidado el procesador.
A-3 Una vez que el procesador se encuentre insertado de forma correcta, vuelva a instalar la cubierta de
proteccin y baje la palanca del socket del procesador y colquela en la posicin de bloqueo.
Cuando la tipo B est correctamente insertada, vuelva a colocar con cuidado la placa metlica. A
continuacin, asegure la palanca B debajo de su lengeta de retencin. La chapa del zcalo podra
desprenderse durante el proceso de sujecin de la palanca. Finalmente, asegure la palanca A debajo de
su lengeta de sujecin para completar la instalacin de la CPU.
Para obtener instrucciones detalladas sobre cmo instalar la CPU, consulte el manual del usuario.
-1-
Espaol
B. Instalacin del procesador AMD (omita este paso si la placa base tiene una CPU integrada)
B-1 Levante por completo la palanca del socket del procesador.
Alinee la clavija 1 del procesador (marca con un tringulo
pequeo) con la marca con un tringulo en el socket del
procesador e inserte con cuidado el procesador en el socket.
Asegrese de que las clavijas del procesador encajen en forma
correcta en los orificios.
B-2 Una vez que el procesador se encuentre insertado dentro
del socket, presione hacia abajo con un dedo en el medio
del procesador y baje la palanca del socket del procesador y
colquela en la posicin de bloqueo.
Clavija 1
No utilice la fuerza para insertar el procesador en el socket del procesador. El procesador no encajar si
se encuentra orientado en forma incorrecta. S Si ste fuera el caso, reajuste la orientacin del procesador.
NO toque los contactos del zcalo. Para proteger el zcalo del procesador, vuelva a colocar siempre la
cubierta protectora del zcalo luego de la instalacin del procesador
Paso
-2-
Paso
Paso
Paso
Se puede conectar hasta dos dispositivos IDE en un conector IDE de la placa madre. Antes de realizar la
instalacin, compruebe la configuracin de los jumpers (principal y secundario) de los dispositivos IDE.
Si se instala ms de un disco duro, acceda al BIOS Setup (Configuracin del BIOS) del sistema para
establecer la secuencia de inicio de los discos duros.
-3-
Espaol
Busque una ranura de expansin que sea compatible con la tarjeta y retire
la tapa de la ranura ubicada en el panel trasero de la caja. Luego, inserte
la tarjeta de expansin en la ranura. Asegure el soporte de la tarjeta de
expansin al panel trasero del de la caja utilizando un tornillo.
Paso
7-1 Conecte los cables en los conectores y conexiones internas de la placa madre, incluidos los conectores
IDE/SATA, audio del panel frontal, USB, IEEE 1394, etc.
7-2 Conecte el mdulo del panel frontal (diferente segn el diseo de la caja y compuesto por un indicador
de encendido, indicador de actividad de disco duro, altavoces, interruptor de reinicio, interruptor de
encendido/apagado, etc.) de la caja a la conexin (F_PANEL) ubicada en la placa madre.
Asignaciones de clavijas A:
+MSG- +PW-
+SPEAK-
Asignaciones de clavijas B:
+MSG- +PW-
+SPEAK-
2
1
+HD- -RES+
NC
+PWR-
Cabecera del panel frontal (Nota) Las asignaciones de clavijas para el header del panel frontal pueden ser distintas segn el modelo.
Consulte el manual de usuario de la placa base para obtener informacin sobre las asignaciones de
clavijas actuales.
Espaol
Paso
Conexin de perifricos
Panel trasero del gabinete
Fuente de alimentacin
Interruptor de
encendido/apagado
Puerto DVI-D
Puerto HDMI
Puerto D-Sub
Puertos eSATA
Conector S/PDIF
Puerto IEE1394
Puertos USB
Conectores de audio
-4-
A sequncia pela qual a instalao feita pode variar conforme o tipo de caixa e os dispositivos
usados. As instrues de instalao embaixo aplicam-se aos sistemas desktop da GIGABYTE e
servem apenas como referncia.
Consulte o manual do utilizador includo juntamente com a placa principal para obter as
especificaes desta.
Antes de instalar os dispositivos, certifique-se de que estes so compatveis com os conectores
existentes no seu computador.
Antes de instalar os dispositivos, certifique-se de que os dispositivos esto desligados no seu
computador. Retire o cabo de alimentao da tomada eltrica para evitar danos ao dispositivos e
os componentes do sistema.
Coloque o computador sobre uma superfcie estvel para evitar uma instalao incorrecta devido
a instabilidade do mesmo.
Etapa
A. Instalao de uma CPU Intel (avance este passo se a placa principal possuir uma CPU incorporada)
A alavanca A
A alavanca B
A-2 Segure na CPU com o polegar e o dedo indicador. Alinhe o pino 1 da CPU (marca de tringulo) com o
canto do socket (ou pode alinhar os entalhes existentes na CPU com as chaves de alinhamento existentes
no respectivo socket) e posicione cuidadosamente a CPU na posio correta.
A-3 Quando a CPU estiver devidamente instalada, reponha a placa de carga e empurre a alavanca do socket
da CPU para que esta retome a sua posio original.
Aps inserir corretamente a tipo B, volte a fechar cuidadosamente a placa de conteno. Em seguida, fixe
a alavanca B abaixo da aba de reteno. A tampa do socket poder saltar da placa de carregamento ao
acionar a alavanca. Por fim, fixe a alavanca A debaixo da aba de reteno para concluir a instalao da CPU.
Consulte o manual do utilizador para obter instrues detalhadas acerca da instalao da CPU.
-1-
Portugus
B. Instalao de uma CPU AMD (avance este passo se a placa principal possuir uma CPU incorporada)
B-1 Levante completamente a alavanca do socket da CPU.
Alinhe o pino 1 da CPU (marca de tringulo) com a marca
de tringulo existente no socket da CPU e posicione
cuidadosamente a CPU no socket. Certifique-se de que os
pinos da CPU ficam bem encaixados nos respectivos orifcios.
B-2 Quando a CPU estiver colocada no respectivo socket, coloque
um dedo sobre a parte central da CPU ao mesmo tempo que
baixa a alavanca do socket e a fixa de forma a esta ficar presa.
Socket da CPU
Pino 1
No force a entrada da CPU no respectivo socket. Se a CPU no estiver posicionada na direo certa
no ser possvel instal-la. Ajuste a posio da CPU se tal acontecer.
NO TOQUE nos contatos do socket. Para proteger o socket da CPU, reponha sempre a capa protetora
quando a CPU no estiver instalada.
Etapa
Instalao Da Memria
Portugus
-2-
Etapa
Etapa
Etapa
Um conector IDE da placa principal permite a ligao de um mximo de dois dis positivos IDE. Antes da
instalao, verifique as definies dos jumpers (principal e secundrio) do seus dispositivos IDE.
Se tiver mais do que uma unidade de disco rgido instalada, entre na pgina de configurao do BIOS para
definir a sequncia de arranque das unidades de disco rgido.
-3-
Portugus
Etapa
7-1 Ligue os cabos aos conectores internos e aos conectores existentes na placa principal incluindo os
conectores IDE/SATA, o conector de udio do painel frontal, o conector USB, os conectores IEEE 1394, etc.
7-2 Ligue o mdulo do painel frontal (varia conforme o design da caixa e pode incluir um LED indicador
de alimentao, de atividade da unidade de disco rgido, altofalantes, boto de reposio do sistema,
comutador de alimentao, etc.) da caixa ao conector respectivo (F_PANEL) existente na placa principal.
Distribuio dos pinos A:
+MSG- +PW-
+SPEAK-
+SPEAK-
2
1
+HD- -RES+
NC
+PWR-
MSG: mensagem/energia/suspenso
em LED
PWR: Energia em LED
PW: Comutao de Energia
20
SPEAK: Altofalante
19
HD: Atividade da unidade do disco
rgido em LED
RES: Comutador de reposio
CI: Conector de deteco de intruso
no chassis
(Nota) A distribuio dos pinos do conector do panel frontal pode variar conforme o modelo.
Consulte o manual do utilizador includo juntamente com a placa principal para mais
informaes sobre a distribuio dos pinos.
Etapa
Portugus
Fonte de
alimentao
Comutador de
alimentao
Conector do cabo de
alimentao
Porta DVI-D
Porta HDMI
Porta D-Sub
Portas eSATA
Conector S/PDIF
Porta IEEE1394
Portas USB
Tomadas de udio
-4-
A. Installation dun processeur Intel (sautez cette tape si la carte mre comprend un CPU intgr)
A-1 Reportez-vous aux instructions suivantes en fonction des caractristiques de votre CPU :
Type A:
Soulevez le levier du socket CPU et la plaque de pression mtallique
se lve galement.
a. Si le cache de protection du socket est fix sur le socket CPU,
retirez-le d'abord.
b. Si le couvercle de protection du socket est fix sur la plaque mtallique
de pression, ne le retirez pas pour l'instant. Le couvercle de la prise
peut sortir automatiquement de la plaque de chargement pendant
le processus de r-engagement du levier aprs l'insertion du CPU.
Type B:
Poussez le levier A (le plus prs du symbole
) vers le bas et l'extrieur du socket pour l'ouvrir.
Puis poussez le levier B (le plus prs du symbole ) vers le bas et l'extrieur du socket et soulevezle. Appuyez doucement sur le levier A pour permettre la plaque de maintient de monter. Ouvrez la
plaque de maintient.
Le levier B
Le levier A
A-3 Une fois que le processeur est correctement insr, remplacez la plaque de charge et repoussez le levier
dans la position de blocage.
Une fois que le type B a t install correctement, remettez la plaque de maintient en faisant attention.
Puis remettez le levier B en position. Le couvercle du socket sera enlev de la plaque de maintient
pendant le processus d'engagement du levier. Enfin, remettez le levier A en position initiale pour terminer
l'installation du CPU.
Pour des instructions dtailles sur l'installation du CPU, veuillez vous rfrer au manuel
d'utilisation.
-1-
Franais
A-2 Tenez le processeur entre votre pouce et votre index. Alignez la marque (triangle) de la broche un du
processeur avec le coin de la broche un de la prise du processeur (ou bien alignez les encoches du
processeur avec les cls dalignement de la prise) et insrez doucement le processeur en place.
B. Installation dun processeur AMD (sautez cette tape si la carte mre comprend un CPU intgr)
B-1 Montez fond le levier le levier du support processeur.
Alignez la broche un du processeur (petit triangle) avec
le triangle situ sur la prise du processeur et insrez
doucement le processeur. Assurez-vous que les broches du
processeursadaptent parfaitement dans leurs trous.
B-2 Une fois que le processeur est positionn, placez un doigt
sur le milieu du processeur, en baissant le levier du support
et en le verrouillant dans la position de blocage.
CPU Socket
Broche 1
Ne faites pas entrer le processeur dans la prise du processeur en forant. Le processeur ne sadaptera pas
sil nest pas orient correctement. Rglez lorientation du processeur si cela se produit.
NE touchez PAS les contacts de la prise ; pour protger la prise du processeur, replacez toujours le couvercle
de protection de la prise lorsque le processeur nest pas install
Installation De La Mmoire
Notez lorientation du module de la mmoire. Enclenchez les attaches de
rtention aux deux extrmits de la prise de la mmoire. Placez le module de
mmoire sur la prise. Placez, de la faon indique sur limage de gauche, vos
doigts sur le bord suprieur de la mmoire, poussez la mmoire vers le bas et
insrez-la verticalement dans la prise de la mmoire. Les attaches situes aux
deux extrmits de la prise se refermeront en place une fois que le module de
la mmoire est correctement insr.
Franais
Etape
-2-
Etape
Etape
Etape
Un connecteur de carte mre IDE peut connecter jusqu deux appareils IDE. Avant linstallation, vrifiez
les rglages du cavalier (matre et esclave) de vos appareils IDE.
Si plus dun disque dur est install, entrez dans les Rglages BIOS du systme pour configurer la
squence de lancement du disque dur.
-3-
Franais
Etape
7-1 Reliez les cbles aux connecteurs internes et aux en-ttes de la carte mre, y compris les connecteurs
IDE/SATA, le connecteur audio du panneau avant, les en-ttes USB, IEEE 1394, etc.
7-2 Attachez le module du panneau avant (diffrent selon la conception du botier, la consistance de
lindicateur de courant, lindicateur de lactivit du disque dur, les haut-parleurs, la commande de
rinitialisation, la commande marche/arrt, etc.) du botier sur len-tte du panneau avant (F_PANEL) de
la carte mre.
Emplacements de broche A :
Emplacements de broche B :
+MSG- +PW-
+MSG- +PW-
+SPEAK-
+SPEAK-
20
19
+HD- -RES+
NC
+PWR-
(Remarque) Les emplacements de broche du panneau avant peuvent tre diffrentes de ceux
indiqus sur le schma. Consultez le mode demploi de la carte mre pour trouver
lemplacement rel des broches.
Etape
Alimentation lectrique
Interrupteur
Connecteur du cordon
dalimentation
Port DVI-D
Port HDMI
Port D-Sub
Ports eSATA
Connecteur S/PDIF
Port IEEE1394
Ports USB
Prises audio
Franais
-4-
La sequenza dellinstallazione pu differire a seconda del tipo di case e dei dispositivi utilizzati. Le
istruzioni per linstallazione indicate in basso si applicano ai sistemi desktop GIGABYTE e sono
solo di riferimento.
Per specifiche dettagliate sulla scheda madre, fare riferimento al manuale utente incluso.
Accertarsi che i dispositivi siano conformi ai connettori sul computer, prima di installarli.
Prima dellinstallazione, accertarsi che i dispositivi e il computer siano spenti. Scollegare il cavo
elettrico dalla presa per evitare di danneggiare i dispositivi e i componenti del sistema.
Posizionare il computer su una superficie stabile per ovviare ai problemi di un'installazione non
corretta dovuta a oscillazioni.
Fase
A. Installazione di una CPU Intel (saltare questa fase se la scheda madre ha una CPU integrata)
A-1 Fare riferimento alle seguenti istruzioni in base alle specifiche della CPU:
Tipo A:
Sollevare la leva del socket della CPU e la piastra metallica si solleva
allo stesso modo.
a. Se il coperchio del socket protettivo fissato al socket della CPU,
necessario prima rimuoverlo.
b. Se la copertura della presa dalla piastra protettiva fissata sulla
piastra di carico in metallo, non rimuoverla in questa fase. La
copertura della presa potrebbe apparire automaticamente fuori dalla
piastra di carico durante il processo di reinnesto della leva dopo aver
inserito la CPU.
Tipo B:
Abbassare la leva A (la pi vicina al contrassegno "
") allontanandola dal socket per sganciarlo.
Quindi abbassare la levetta B (la pi vicina al contrassegno " ") allontanandola dal socket e alzare.
Premere delicatamente sulla leva A per consentire alla placchetta di fermo di alzarsi. Aprire la placchetta.
La levetta A
La levetta B
A-2 Afferrare la CPU con il pollice e l'indice. Allineare il segno del pin uno della CPU (triangolo) con langolo
del pin uno dellalloggiamento (oppure allineare le tacche della CPU ai segni sullalloggiamento) e inserire
delicatamente la CPU al suo posto.
A-3 Una volta inserita correttamente la CPU, rimettere la piastra e spingere indietro la leva dellalloggiamento
in posizione di blocco.
Una volta correttamente inserita la tipo A, riposizionare con cura la placchetta di fermo. Quindi fissare la
levetta B sotto la sua linguetta di arresto. Il coperchio del socket pu saltar fuori dalla placchetta di fermo
durante l'operazione di aggancio della leva. Infine, per completare l'installazione della CPU, spingere la
leva A sotto la sua linguetta di arresto.
-1-
Italiano
Per istruzioni dettagliate sull'installazione della CPU, fare riferimento al manuale dell'utente.
B. Installazione di una CPU AMD (saltare questa fase se la scheda madre ha una CPU integrata)
B-1 Sollevare completamente la leva dellalloggiamento della
CPU. Allineare il pin uno della CPU (simbolo del triangolino)
con il segno del triangolo sullalloggiamento ed inserire
delicatamente la CPU. Accertarsi che i pin della CPU si
inseriscano perfettamente nei fori.
B-2 Una volta inserita, poggiare un dito al centro della CPU,
abbassando la leva dellalloggiamento e bloccandola in
posizione.
CPU Socket
Pin 1
Non forzare la CPU nellalloggiamento. La CPU non pu essere inserita, se orientata in maniera errata. In
questo caso, orientare correttamente la CPU.
NON toccare i contatti dellalloggiamento. Per proteggere lalloggiamento della CPU, riposizionare sempre
le coperture di protezione quando la CPU non installata.
2
Fase
3
Fase
Italiano
-2-
Fase
Fase
6
Fase
Un connettore IDE della scheda madre pu collegare fino a due dispositivi IDE. Prima dellinstallazione
controllare le impostazioni dei jumper (master e slave) sui dispositivi IDE.
Se installato pi di un disco rigido, accedere al BIOS Setup del sistema per impostare la sequenza di
avvio del disco rigido.
Italiano
-3-
7
Fase
7-1 Collegare i cavi ai connettori interni e ai connettori sulla scheda madre, inclusi i connettori IDE/SATA e
quelli dellaudio del pannello frontale, USB, IEEE 1394 ecc.
7-2 Collegare il modulo del pannello frontale (diverso a seconda della struttura del case e che composto
da spia di alimentazione, spia dellattivit del disco rigido, altoparlanti, tasto di reset, tasto di accensione,
ecc.) dal case al connettore del pannello frontale (F_PANEL) sulla scheda madre.
Assegnazioni pin A:
+MSG- +PW-
+SPEAK-
Assegnazioni pin B:
+MSG- +PW-
+SPEAK-
2
1
+HD- -RES+
NC
+PWR-
(Nota) Le assegnazioni dei pin del pannello frontale possono differire da modello a modello. Fare riferimento
al manuale utente della scheda madre per le assegnazioni reali dei pin.
8
Fase
Periferiche Di Connessione
Pannello posteriore del telaio
Alimentatore
Interruttore di
alimentazione
Porta DVI-D
Porta HDMI
Porte eSATA
Porta IEEE1394
Jack audio
Porta D-Sub
Connettore S/PDIF
Porte USB
Porta LAN RJ-45
Italiano
Scheda grafica
esterna
-4-
.
Intel ( ,
)
A-1 , :
:
,
a. ,
.
b.
, .
.
B:
( "
") ,
. ( " ")
, , .
, . .
A
A-2 , 1-
1- (
) .
A-3 , , ,
.
B
. .
. ,
.
.
-1-
.
GIGABYTE .
.
6,
.
.
.
.
,
.
. AMD ( ,
)
B-1
. 1-
. ,
.
B-2 ,
,
.
CPU Socket
.
. .
! ,
.
.
C-1
.
(
) .
C-2 CPU_
FAN .
.
. DIMM-
.
, ,
. ,
.
GIGABYTE.
, .
.
.
,
.
,
.
-2-
/
/
. ,
/.
.
.
/
,
.
. .
.
PCI Express
() ,
.
, .
IDE- SATA-
6-1 (DVD-ROM CD-ROM).
5,25- .
.
IDE IDE-.
IDE-
(master slave).
,
BIOS Setup , .
-3-
+SPEAK-
+MSG- +PW-
+SPEAK-
20
19
+HD- -RES+
NC
+PWR-
MSG: /
/
PWR:
PW:
SPEAK:
HD:
RES:
CI:
()
. F_PANEL
.
PS/2
DVI-D
HDMI
eSATA
IEEE 1394
PS/2
D-Sub
S/PDIF
USB
RJ-45
-4-
c ,
: , , ..
,
.
Kolejno instalacji moe si rni w zalenoci od typu obudowy oraz instalowanych urzdze.
Ponisza kolejno instalacji zostaa pokazana na przykadzie systemu GIGABYTE i suy jedynie
celom informacyjnym.
W celu uzyskania dokadnej specyfikacji pyty gwnej, prosz skorzysta z instrukcji uytkownika.
Przed zainstalowaniem urzdze, upewnij si e s one kompatybilne ze zczami w twoim
komputerze.
Przed instalacj urzdze upewnij si e zarwno one jak i komputer s wyczone. Odcz kabel
zasilajcy od zasilacza by unikn uszkodzenia sprztu.
Umie komputer na stabilnej powierzchni by unikn nieprawidowej instalacji bdcej wynikiem
wstrzsw.
Krok
A. Instalacja procesora Intel (moesz pomin ten etap, jeli Twoja pyta gwna posiada
zintegrowany procesor)
A-1 Zapoznaj si z poniszymi instrukcjami w oparciu o specyfikacj procesora:
Typ A:
Unie dwigni gniazda procesora, metalowa osona rwnie zostanie
podniesiona.
a. Jeeli pytka zabezpieczajca gniazdo procesora jest zamocowana
do gniazda, naley j najpierw usun.
b. Jeeli pytka zabezpieczajca gniazdo procesora jest zamocowana do
gniazda, nie naley jej usuwa na tym etapie. Pytka zabezpieczajca
gniazdo procesora moe automatycznie odskoczy od gniazda
podczas procesu zakadania dwigni po umieszczeniu procesora.
Typ B:
Nacinij w d i w bok dwigni A (najbliej oznaczenia "
"), aby otworzy socket. Nastpnie nacinij
w d i w bok dwigni B (najbliej oznaczenia " "). Delikatnie nacinij dwigni A, aby pozwoli
metalowej osonie unie si.
Dwigni A
Dwigni B
A-2 Trzymajc pewnie procesor pomidzy kciukiem a palcem wskazujcym wyrwnaj may zoty trjkt na
brzegu procesora z rogiem wskazujcym pin pierwszy na gniedzie procesora (lub zrwnaj wcicia na
procesorze z naciciami na zczu) i delikatnie w procesor do gniazda.
A-3 Gdy procesor jest ju prawidowo osadzony, naley umieci na nim pytk zabezpieczajc i przesun
dwigni gniazda procesora z powrotem do pozycji zamknitej.
Kiedy procesor typ B jest prawidowo woony, delikatnie wycignij pytk. Zabezpiecz dwigni B. Osona
socketu moe odskoczy w momencie unoszenia dwigni. Na koniec zabezpiecz dwigni A w celu
zakoczenia procesu instalacji CPU.
Szczegwa instukcja instalacji procesora znajduje si w instrukcji obsugi.
-1-
Polski
B. Instalacja procesora AMD (moesz pomin ten etap, jeli Twoja pyta gwna posiada
zintegrowany procesor)
Polski
CPU Socket
Pin 1
Nie umieszczaj procesora w gniedzie na si. Nie ma moliwoci niepoprawnego woenia procesora. Jeli
zajdzie taka potrzeba, popraw dopasowanie procesora.
Uwaga! W adnym wypadku nie naley dotyka zczy gniazda procesora. W celu ochrony gniazda procesora,
zawsze naley zakada to zabezpieczenie jeli procesor nie jest zainstalowany.
Instalacja pamici
Zwr uwag na uoenie moduw pamici. Odchyl zatrzaski zabezpieczajce
na obu kocach gniazda. Umie modu pamici w gniedzie. Jak pokazano
na obrazku po lewej stronie, umie palec na grze moduu pamici i docinij.
Zatrzaski na obu kocach gniazda powinny si zamkn, blokujc w ten sposb
pami w prawidowej pozycji.
Krok
-2-
Krok
Krok
Krok
o jednego zcza IDE mona podczy do dwch urzdze IDE. Przed instalacj sprawd ustawienie
D
zworek (master and slave) na urzdzeniu IDE.
Jeli zainstalowano wicej ni jeden dysk twardy, wejd w BIOS pyty gwnej i ustaw prawidow
sekwencj bootowania.
-3-
Polski
tylna blaszka
Krok
Oznaczenia pinw A:
+MSG- +PW-
+SPEAK-
Oznaczenia pinw B:
+MSG- +PW-
+SPEAK20
19
+HD- -RES+
NC
+PWR-
Uwaga: zcza pinowe front panel'u mog si rni w zalenoci od modelu. Przeczytaj instrukcj obsugi
pyty gwnej dla sprawdzenia aktualnego rozmieszenia pin'w
Krok
Zasilacz
Wcznik napicia
Port DVI-D
Port HDMI
Port D-Sub
Port eSATA
Zcze S/PDIF
Port IEEE1394
Porty USB
Gniazda Audio
-4-
Kurulum sras, kasann trne ve kullanlan aygtlara gre deiiklik gsterebilir. Aadaki
kurulum talimatlar GIGABYTE'nin masast sistemleri iin geerli olup sadece bilgi amaldr.
Detayl anakart zellikleri iin kullanc el kitabna bakn.
Aygtlarn kurulumunu yapmadan nce, aygtlarnzn bilgisayarnzdaki girilerle uyumlu olup
olmadndan emin olun.
Aygtlarn kurulumunu yapmadan nce, aygtlar ve bilgisayarnz kapattnzdan emin
olun. Aygtlara ve sistem bileenlerine zarar gelmesini nlemek iin g kablosunu elektrik
fiinden karn.
Sarsnt ya da geveklik nedeni ile oluabilecek kaymalardan, kontrolsz yer deitirmelerinden
dolay meydana gelebilecek hasarlar nlemek iin bilgisayar sistemini salam bir yzeye
koyun.
Adm
A. Intel CPU Kurulumu (Anakartta yerleik bir CPU varsa bu adm atlayn)
Tip B:
A kolunu ("
" iaretine en yakn olan) aaya doru soketten uzaklatrarak an. Ardndan B
kolunu (" " iaretine en yakn olan) aaya doru soketten uzaklatrn ve kaldrn. Yk plakasnn
kaldrlmasna olanak salamak iin A koluna hafife bastrn. Yk plakasn an.
A kolunu
B kolunu
A-2 CPUyu baparmanzla ve iaret parmanzla tutun. aretli olan (gen) CPU pini CPU yuvasnn
kesindeki iareti ile yan yana gelecek ekilde hizalayn (ya da CPU dilileri ile yuva hizalama entiklerine
gre hizalayabilirsiniz) ve hafife bastrarak CPUyu yerine takn.
A-3 CPU doru olarak yerletirildikten sonra, metal levhay yerine yerletirin ve CPU kolunu iterek eski kilitli
konumuna getirin.
Tip B dzgn bir ekilde yerletirildiinde, yk plakasn dikkatlice yerletirin. Ardndan B kolunu tutma
sekmesinin altnda sabitleyin. Soket kapa kolu takarkenki sre srasnda yk plakasndan kabilir. Son
olarak A kolunu tutma sekmesinin altnda tutarak CPU kurulumunu tamamlayn.
CPU kurulumu hakknda ayrntl talimatlar iin, ltfen kullanc klavuzuna bakn.
-1-
Trke
B. AMD CPU Kurulumu (Anakartta yerleik bir CPU varsa bu adm atlayn)
B-1 CPU yuva kolunu tamamen kaldrn. lk CPU pini (ufak gen
iaretli) ile CPU yuvasndaki gen iareti ayn hizaya getirin
ve hafife bastrarak CPUyu yerine takn. CPU pinlerinin tam
olarak deliklere uyduundan emin olun.
B-2 CPU yuvaya yerletirildiinde, bir parmanz CPUnun
ortasna koyun ve yuva kolunu indirerek tamamen kilitli
duruma getirin.
CPU yuva
lk CPU pini
CPUyu CPU yuvasna takarken zorlamayn. CPU, yuvaya doru bir ekilde yerletirilmedike; CPU, yerine
oturmaz. Eer bu olursa ynn uygun bir ekilde ayarlayn.
Soket temas yerlerine DOKUNMAYIN. CPU soketini korumak iin, koruyucu soket kapan daima CPU
takl deilken deitirin.
Trke
2
Adm
Bellein Kurulumu
Bellek modlnn giri ynlerine dikkat edin. Bellek yuvalarnn iki ucundaki tutma
klipslerini iki yana an. Bellek modln yuvaya yerletirin. Soldaki resimde
gsterildii gibi, parmaklarnz bellein iki st ucuna yerletirin, bellein zerine
bastrarak bellek yuvasna dikey bir ekilde yerletirin. Bellek modl dzgn bir
ekilde yerletirildiinde yuvann iki ucundaki tutma klipsleri yuvasna oturacak.
3
Adm
-2-
Adm
Anakartn Kurulumu
Arka paneldeki I/O (Giri/k) balant noktalarna sahip orijinal plakay anakart
ile gelen G/ plakas ile deitirin. G/ plakasna denk gelecek ekilde anakart
kasann iine yerletirin. Anakarttaki montaj delikleri ile kasann zerindeki
montaj deliklerini uygun gelecek bir ekilde hizalayn. Anakart vidalarla yerine
skca oturtun.
G/ Plakas
Adm
6
Adm
Bir anakart IDE giriine iki adet IDE srcs balanabilir. Kurulumdan nce, IDE srclerinin zerindeki
jumper ayarlarn (master ve slave) kontrol edin.
Eer birden fazla sabit src kurulduysa, sistemdeki BIOS ayarlarna girerek sabit srclerin nykleme
srasn ayarlayn.
-3-
Trke
7
Adm
7-1 IDE/SATA konektrleri ve n panel ses, USB, IEEE 1394 balantlar, anakarttaki dahili konektrlere ve
balant noktalarna balayn.
7-2 n panel modln (g dmesi, yeniden balatma dmesi, hoparlrler, sabit disk faaliyet gstergesi
ve g gstergesi vs. kasann tipine gre deiiklik gsterebilir) kasadan anakarttaki n panel
balantsna (F_PANEL) takn.
Pim yeri A:
+MSG- +PW-
Pim yeri B:
+SPEAK-
+MSG- +PW-
+SPEAK-
20
n Panel Balants
19
+HD- -RES+
NC
+PWR-
(Not) n panel balantsnn pim yerleri modele gre farkllk gsterebilir. Asl pim yerleri iin ana kartnzn
kullanma klavuzuna baknz.
Trke
Adm
G Kayna
PS/2 Klavye
Balant Noktas
DVI-D Balant
Noktas
HDMI Balant
Noktas
eSATA Balant
Noktalar
IEEE 1394 Balant
Noktas
Ses Jaklar
-4-
Pasul
A. Instalarea unui CPU Intel (ignorai acest pas dac placa de baz are un CPU ncorporat)
Prghia A
Prghia B
A-2 Hold the CPU with your thumb and index fingers. Align the CPU pin one marking (triangle) with the pin one
corner of the CPU socket (or you may align the CPU notches with the socket alignment keys) and gently
insert the CPU into position.
A-3 O dat ce CPU-ul este introdus corect, aezai din nou plcua de metal i mpingei braul soclului de CPU
napoi n poziia blocat.
Dup ce unitatea tip B este fixat corect, nlocuii cu grij plcua de ncrcare. Apoi fixai mnerul B sub
dispozitivul de prindere. Capacul soclului se poate desprinde singur de pe plcua de ncrcare n timp ce
acionai mnerul. n final, fixai mnerul A sub dispozitivul de prindere pentru a finaliza instalarea CPU-ului.
Pentru instruciuni detaliate privind instalarea procesorului, consultai manualul de utilizare.
-1-
Romn
B. Instalarea unui CPU AMD (ignorai acest pas dac placa de baz are un CPU ncorporat)
B-1 Ridicai complet braul soclului de CPU. Aliniai pinul unu al
CPU-ului (marcajul de triunghi mic) cu marcajul de triunghi
de pe soclul de CPU i introducei uor CPU-ul n soclu.
Asigurai-v c pinii CPU-ului se potrivesc perfect n orificii.
B-2 O dat ce CPU-ul este poziionat n soclu, aezai un deget
n mijlocul CPU-ului, cobornd braul soclului i fixndu-l n
poziia blocat complet.
Soclului de CPU
Pin 1
Nu forai CPU-ul n soclul de CPU. CPU-ul nu potrivete dac este orientat incorect. Reglai orientarea
CPU-ului dac se ntmpl acest lucru.
NU atingei contactele soclului. Pentru a proteja soclul procesorului, nlocuii carcasa de protecie numai
atunci cnd procesorul nu este instalat.
Pasul
Instalarea Memoriei
Romn
Pasul
-2-
Pasul
Pasul
Pasul
Un conector IDE de pe placa de baz poate conecta pn la dou dispozitive IDE. nainte de instalare,
verificai setrile elementelor de legtur (unitate master i slave) de pe dispozitivele IDE .
Dac este instalat mai mult de un hard disk, intrai n configurarea BIOS a sistemului pentru setarea
secvenei de ncrcare a hard disk-urilor.
-3-
Romn
6-1 Instalai unitile optice, precum unitile DVD-ROM i CD-ROM. ndeprtai capacul
bay-ului pentru unitate de 5,25 de pe partea din fa a carcasei. Montai unitatea
optic n bay-ul pentru unitate de 5,25 i fixai-o cu uruburi.
Pasul
7-1 Conectai cablurile la conectorii i distribuitorii interni de pe placa de baz, inclusiv conectorii IDE/SATA,
audio de pe panoul frontal, USB, distribuitori IEEE 1394 etc.
7-2 Ataai modulul panoului frontal (difer n funcie de designul carcasei, cuprinznd indicatorul de alimentare,
indicatorul de activitate a hard disk-ului, difuzoarele, ntreruptorul de reiniializare, ntreruptorul de
alimentare etc.) de pe carcas pe distribuitorul panoului frontal (F_PANEL) (PANOU_F) de pe placa de
baz.
Semnificaia pinului A:
+MSG- +PW-
+SPEAK-
Semnificaia pinului B:
+MSG- +PW-
+SPEAK-
20
19
+HD- -RES+
NC
+PWR-
(Not) Semnificaia pinilor de pe comutatorul din partea frontal poate s fie diferit n funcie de model. Consultai
manualul de utilizare al plcii de baz pentru semnificaia corect a pinilor.
Pasul
Conectarea Perifericelor
Surs de
alimentare
Port PS/2 pentru
tastatur
Romn
Port DVI-D
Port HDMI
Port D-Sub
Porturi eSATA
Conector S/PDIF
Port IEEE1394
Porturi USB
Mufe audio
-4-
. - GIGABYTE
.
.
, ,
.
, . ,
.
,
.
A. Intel (
)
A-1 , :
:
.
a.
, .
b.
, .
.
B:
(- "
") ,
. (- " ") ,
. , .
.
A
A-3 ,
.
B , .
.
. ,
, .
.
-1-
A-2 . 1
() (
) .
B. AMD (
)
B-1 .
1 ( )
. ,
.
B-2 ,
.
CPU Socket
, .
. , , .
. ,
, .
C.
C-1 ,
. (
).
C-2
,
.
.
.
. ,
,
. ,
.
GIGABYTE .
, .
.
.
, ,
.
,
,
, .
-2-
I/O
I/O .
, I/O .
.
.
I/O
,
.
.
.
PCI Express
,
. , .
, .
IDE SATA
6-1 DVD-ROM CD-ROM.
5.25 .
5.25 .
IDE IDE . ,
( ) IDE .
, BIOS,
.
-3-
7-1 , IDE/SATA
, USB, IEEE 1394 ...
7-2 (
, , , ,
..) (F_PANEL) .
:
+MSG- +PW-
+SPEAK-
B:
+MSG- +PW-
+SPEAK-
2
1
+HD- -RES+
NC
+PWR-
MSG: /. ./
sleep
PWR: . .
20 PW:
SPEAK:
19
HD:
RES:
CI:
() .
.
PS/2
DVI-D
PS/2
HDMI
D-Sub
eSATA
S/PDIF
IEEE1394
USB
RJ-45 LAN
-4-
-,
,
, , ,
.
.
A. Intel CPU beszerelse (Hagyja ki ezt a lpst, ha az alaplapon beptett processzor van)
A-1 A CPU mszaki adatai alapjn tekintse meg az albbi utastsokat:
A tpus:
Emelje fel a CPU-foglalat rgzt karjt, s vele egytt felemelkedik a
fm tartlemez.
a. Ha a CPU-foglalon vdlap tallhat, tvoltsa el.
b. Ha a foglalat vdbortsa a fm tartlemezhez van rgztve, mg
ne tvoltsa el. A foglalat fedele magtl lepattanhat a tartlemezrl,
amikor a kart rgzti, miutn behelyezte a CPU-t.
B tpus:
Az "A" jel kart (a "
" jells kzelben) nyomja lefel s a foglalattal ellenttes irnyba a kioldshoz.
A "B" jel kart (a " " jells kzelben) pedig nyomja lefel s a foglalattal ellenttes irnyba a
felemelshez. vatosan nyomja le az "A" jel kart, hogy felemelkedhessen a tartlemez. Nyissa fel
a tartlemezt.
Az "A" jel kart
A-2 Hvelykujjval s mutatujjval tartsa a CPU-t. Illessze egymshoz a processzor els t jelzst (hromszg)
a processzor foglalat els t sarkval (vagy illessze ssze a processzor bevgsait a foglalat sszeilleszt
kulcsaival), majd vatosan helyezze a processzort a foglalatba.
A-3 A processzor behelyezse utn helyezze vissza a tartlemezt, majd nyomja vissza a processzor emelkarjt
zr llsba.
Amint megfelelen beszerelte az B tpus, vatosan helyezze vissza a tartlemezt. Ezutn rgztse a "B"
rgztkart hajtsa a tartfl al. A foglalat fedele lepattanhat a tartlemezrl, amikor a kart rgzti. Vgl
rgztse az "A" rgztkart a tartfl al a CPU beszerelsnek befejezshez.
-1-
Magyar
B. AMD CPU beszerelse (Hagyja ki ezt a lpst, ha az alaplapon beptett processzor van)
B-1 Emelje meg teljesen a processzor foglalatnak rgzt
karjt. Illessze egymshoz a processzor els tjt (kis
hromszg jelzs) a processzor foglalaton lev hromszg
jelzssel, majd vatosan helyezze a processzort a foglalatba.
Gyzdjn meg arrl, hogy a processzor ti tkletesen
illeszkednek a nylsokba.
B-2 A processzornak foglalatba helyezse utn nyomja r az egyik
ujjt a processzor kzepre, engedje le a foglalat rgzt
karjt, majd akassza be teljesen rgztett llsba.
CPU foglalat
Els t
C. Processzorht beszerelse
C-1 A processzorht beszerelse eltt a processzor felletre kenjen
egy vkony rteg hnyel pasztt. Ezutn szerelje be a htt
(lsd a processzorht beszerelsi kziknyvt).
C-2 Csatlakoztassa a processzorht tpkbelt az alaplapon
lev CPU_FAN csatlakozhoz gy, hogy a ht megfelelen
mkdhessen, megakadlyozva a processzor tlmelegedst.
Lps
Memria Beszerelse
Figyelje meg a memriamodul tagolst. Hzza szt a memria foglalat kt vgn
lev rgztket. Helyezze a memriamodult a foglalatba. A balra lev brn lthat
mdon helyezze ujjait a memriamodul fels lre, s fgglegesen nyomja be a
memriamodult a foglalatba. Miutn a memriamodul helyre kerl a foglalatban,
a foglalat kt vgn lev rgztk bekattannak helykre.
Lps
A Hz Elksztse a s Tp Beszerelse
A GIGABYTE asztali rendszer pldjt kvetve elszr tvoltsa el a hz mindkt
oldallapjt s a fedelt, hogy beszerelje a tpot. Helyezze a tpegysget a
megfelel helyre a szmtgphzban s rgztse csavarokkal. A tp beszerelse
s elhelyezse eltrhet az brn bemutatott pldtl.
Magyar
-2-
Lps
Az Alaplap Beszerelse
Vegye le a hz htuljn lev eredeti I/O vdlapot, s helyette az alaplap
I/O vdlapjt helyezze be. Helyezze a hzba az alaplapot gy, hogy az I/O
vdlaphoz illeszti azt. Illessze egymshoz a rgzt csavaroknak sznt nylsokat
a dobozon lev megfelel nylsokhoz. Csavarokkal rgztse az alaplapot.
Lps
Bvtkrtya Beszerelse
Keresse meg azt a bvt foglalatot, amelyet a krtynak tartottak fenn, majd
tvoltsa el a foglalat vdlapjt a hz htuljrl. Helyezze be a bvtkrtyt
a foglalatba. Rgztse a bvtkrtya fmtartjt a szmtgphz htlapjhoz
egy csavarral.
Bvtkrtya beszerzse eltt ellenrizze a krtya hosszsgt, hogy
befr-e a szmtgphzba.
Gyzdjn meg arrl, hogy a bvtkrtyt teljesen belenyomta a
foglalatba.
Lps
Az alaplap egyetlen IDE csatlakozjhoz maximum kt IDE eszkz csatlakoztathat. A beszerels eltt
ellenrizze az IDE eszkzk jumper-belltst (Master s Slave).
Ha tbb merevlemezt szerel be, lpjen a rendszer BIOS-belltsokba, hogy belltsa az indtsi sorrendet.
Magyar
-3-
Lps
7-1 Csatlakoztassa a kbeleket az alaplapon lev bels csatlakozkhoz s foglalatokhoz, belertve az IDE/
SATA csatlakozkat, az ells panelen lev audio csatlakozkat, az USB, IEEE 1394 csatlakozkat stb.
7-2 Csatlakoztassa a hz ells paneljnek moduljt (a hz formatervezstl fgg, s a bekapcsolva kijelzt,
a merevlemez tevkenysg kijelzt, hangszrkat, jraindt kapcsolt, be-/kikapcsolt stb. tartalmazza)
az alaplapon lev ells panel csatlakozjhoz (F_PANEL).
A rintkez-kioszts:
+MSG- +PW-
+SPEAK-
B rintkez-kioszts:
+MSG- +PW-
+SPEAK-
20
19
+HD- -RES+
NC
+PWR-
A tartozkok csatlakoztatsa
Kszlkhz htlapja
Tpegysg
zemkapcsol
PS/2
billentyzetcsatlakoz
Tpkbel csatlakoz
DVI-D csatlakoz
PS/2 egrcsatlakoz
HDMI csatlakoz
D-Sub csatlakoz
eSATA csatlakozk
S/PDIF csatlakoz
IEEE1394 csatlakoz
USB-csatlakozk
Audi aljzatok
RJ-45 LAN-csatlakoz
Magyar
-4-
A.
Intel (
CPU)
A-1 CPU :
:
CPU
.
a.
CPU, .
b.
, .
CPU.
B:
( "
")
. , ( " ")
.
. .
A
A-2 .
() (
)
.
A-3 ,
.
( B),
. , .
. ,
(CPU).
CPU, .
-1-
. GIGABYTE
.
.
,
.
,
.
.
.
B.
AMD (
CPU)
B-1 .
(
)
.
.
B-2 ,
,
.
CPU Socket
Pin 1
.
. , .
. ,
.
C.
C-1 ,
. , (
).
C-2
CPU_FAN
.
.
.
. ,
,
.
.
GIGABYTE ,
.
.
.
,
.
,
.
-2-
I/O
I/O .
I/O.
. .
/
. ,
.
.
PCI Express
,
.
.
IDE SATA
6-1 , DVD-ROM CD-ROM.
5.25
. 5.25
.
IDE IDE.
, (master slave)
IDE.
,
BIOS .
-3-
7-1 ,
IDE/SATA , USB, IEEE 1394 .
7-2 (
, , ,
, , )
(F_PANEL).
:
+MSG- +PW-
+SPEAK-
:
+MSG- +PW-
+SPEAK-
2
1
+HD- -RES+
NC
+PWR-
MSG: //
LED
PWR: LED
20 PW:
SPEAK:
19
HD: LED
RES:
CI:
() .
.
PS/2
DVI-D
PS/2
HDMI
D-Sub
eSATA
S/PDIF
IEEE1394
USB
RJ-45
-4-
,
, , ,
. , ,
.
A. Instalace procesoru Intel (peskote tento krok, pokud je zkladn deska vybavena
integrovanm procesorem)
A-1 Dodrujte nsledujc pokyny, kter jsou zaloeny naspecifikacch vaeho procesoru:
Typ A:
Zvednte pku patice procesoru; souasn se zvedne kovov
zatovac destika.
a. Je-li napatici procesoru pipevnn ochrann kryt, sejmte jej jako
prvn.
b. Pokud je ochrann kryt patice pipevnn ke kovov zavdc desce, v
tto chvli jej nesnmejte. Bhem procesu zajiovn pky po vloen
procesoru me dojt k odskoen krytu patice ze zavdc desky.
Typ B:
Uvolnte pku A (nejble znace "
") stisknutm dol od patice. Potom uvolnte pku B (nejble
znace " ") stisknutm dol od patice a zvednte ji. Opatrnm stisknutm pky A nechte zvednout
zavdc desku. Otevete zavdc desku.
Pku A
Pku B
A-2 Uchopte procesor palcem a ukazovkem. Zorientujte znaku kolku 1 procesoru (trojhelnk) s rohem kolku
1 patice procesoru (nebo mete zorientovat drky na procesoru kli pro zarovnn patice) a opatrn
zasute procesor na msto.
A-3 Po sprvnm usazen procesoru nasate zavdc desku a zatlate pku patice procesoru do zamknut polohy.
Kdy je typ B sprvn usazen, opatrn nasate zavdc desku. Potom zajistte pku B pod jej zajiovac
jazek. Bhem procesu zajiovn pky me dojt k odskoen krytu patice ze zavdc desky. Nakonec
dokonete instalaci procesoru zajitnm pky A pod jej zajiovac jazek.
Podrobn pokyny kinstalaci procesoru naleznete vnvodu kpouit.
-1-
etina
etina
B. Instalace procesoru AMD (peskote tento krok, pokud je zkladn deska vybavena
integrovanm procesorem)
etina
Patice procesoru
Kolk 1
Nezatlaujte procesor do patice silou. Nesprvn zorientovan procesor nelze usadit. V takovm ppad
zmte orientaci procesoru.
NEDOTKEJTE SE kontakt patice. Pokud nen nainstalovn procesor, vdy nasate ochrann kryt
patice procesoru, aby se zabrnilo jejmu pokozen.
Instalace Pamti
Poznamenejte si orientaci pamovho modulu. Rozthnte zajiovac svorky na
obou koncch patice pamovho modulu. Umstte pamov modul na patici.
Podle obrzku vlevo polote prsty na okraj pamovho modulu, tlate modul
dol a zasute jej svisle do patice pamovho modulu. Kdy je pamov modul
zcela usazen, svorky na obou koncch patice zacvaknou na mst.
Krok
-2-
Krok
Krok
K jednomu konektoru IDE na zkladn desce lze pipojit a dv zazen IDE. Ped instalac zkontrolujte
nastaven propojek (nadazen a podazen) na zazench IDE.
Je-li nainstalovn vce ne jeden pevn disk, pejdte do sti BIOS SS Setup (Nastaven systmu BIOS)
a nastavte zavdc sekvenci pevnch disk.
-3-
etina
etina
Krytka I/O
Krok
etina
7-1 Pipojte kabely k internm konektorm a paticm na zkladn desce vetn konektor IDE/SATA,
konektor zvuku na pednm panelu, konektor USB, patic IEEE 1394 atd.
7-2 Pipevnte modul pednho panelu (li se v zvislosti na designu skn, skld se z indiktoru napjen,
indiktoru innosti pevnho disku, reproduktor, resetovacho spnae, vypnae napjen atd.) ze skn
k patici pednho panelu (F_PANEL) na zkladn desce.
Piazen vvod A:
+MSG- +PW-
+SPEAK-
Piazen vvod B:
+MSG- +PW-
+SPEAK-
2
1
+HD- -RES+
NC
+PWR-
(Poznmka) Piazen vvod pro hlaviku pednho panelu se me liit podle modelu.
Aktuln piazen vvod viz uivatelsk pruka k zkladn desce.
Krok
Pipojen Perifri
Zadn panel skn
Zdroj napjen
Vypna
Konektor napjen
Port DVI-D
Port HDMI
Port D-Sub
Porty eSATA
Konektor S/PDIF
Port IEEE1394
Porty USB
Zdky zvuku
-4-
Redosled koraka prilikom instalacije moe se razlikovati u zavisnosti od sluaja i ureaja koji
se koriste. Instrukcije za instalaciju koje ete nai ispod vae za desktop sisteme kompanije
GIGABYTE i slue samo kao referentni materijal.
Pogledajte Uputstvo za korienje koje ste dobili za detaljne specifikacije vezane za matinu
plou.
Pre instaliranja ureaja, proverite da su vai ureaji kompatibilni sa konektorima na vaem
kompjuteru.
Pre instaliranja ureaja obavezno iskljuite svoje ureaje i svoj kompjuter. Izvucite kabl za
struju iz tekera da bi spreili oteenje ureaja i komponenti sistema.
Postavite kompjuterski sistem na stabilnu povrinu da bi spreili nepravilnu instalaciju usled
klimanja.
Korak
A. Instaliranje Intelovog procesora (preskoite ovaj korak ukoliko matina ploa ima ugraen procesor)
Polugu A
Polugu B
A-2 Drite procesor palcem i kaiprstom. Poravnajte oznaku prve noice procesora (trougao) sa uglom za iodu
jedan na podnoju procesora (ili moete da poravnate lebove procesora sa oznakama za poravnavanje
podnoja) i paljivo ubacite procesor na mesto.
A-3 Jednom kada je procesor ispravno postavljen, spustite ploicu za optereivanje i gurnite ruicu za podnoje
procesora natrag u poloaj za blokiranje.
Jednom kada je tip B ispravno ubaen, paljivo postavite ploicu za pritiskanje. Potom zategnite i zakljuajte
polugu B ispod njenog zateznog jezika. Poklopac podnoja moe da se otkai sa ploice za pritiskanje
tokom procesa zatezanja polugice. Na kraju, zategnite i zakljuajte polugu A ispod njenog zateznog jezika
da zavrite instaliranje procesora.
Detaljna uputstva za montiranje procesora potraite u korisnikom priruniku.
-1-
Srpski
B. Instaliranje AMD procesora (preskoite ovaj korak ukoliko matina ploa ima ugraen
procesor)
B-1 Potpuno podignite ruicu za zakljuavanje procesora.
Poravnajte noicu jedan procesora (oznaenu malim
trouglom) sa trouglastom oznakom na podnoju procesora
i paljivo ubacite procesor u podnoje. Proverite da noice
procesora savreno upadaju u svoje rupice.
B-2 Kada je procesor postavljen na svoje mesto, stavite jedan prst
na sredinu procesora, sputajui na taj nain ruicu podnoja
i fiksirajui je u potpuno zablokiranom poloaju.
CPU Socket
Pin 1
Nemojte na silu da ubacujete procesor u podnoje za procesor. Procesor nee ulei ukoliko je pogreno
okrenut. Ukoliko procesor nee da ulegne, probajte da okrenete procesor.
Ne dodirujte podnoje procesora. Kako bi podnoje uvek bilo zatieno, uvek vratite zatitni poklopac
kada procesor nije instaliran
Srpski
Korak
Instaliranje memorije
Obratite panju na to kako je okrenut memorijski modul. Rairite klipove koji dre
memoriju sa obe strane podnoja za memoriju. Smestite memorijski modul u
podnoje. Kako je prikazano na slici levo, stavite prste na vrh memorije, pritisnite
memoriju i ubacite je vertikalno u podnoje za memoriju. Klipovi sa obe strane
podnoja e se vratiti na mesto kada je memorijski modul ispravno ubaen.
Korak
-2-
Korak
I/O tit
Korak
Jedan IDE konektor na matinoj ploi moe da povee do dva IDE ureaja. Pre instalacije, proverite kako
su podeeni damperi (master i slejv) na vaim IDE ureajima.
Ukoliko ste instalirali vie od jednog hard diska, uite u BIOS podeavanja da bi odredili redosled
podizanja hard diskova.
-3-
Srpski
Pronaite odreeni port (slot) koji podrava vau karticu i uklonite poklopac porta
(slota) sa zadnje strane kuita. Potom ubacite karticu u port (slot). Privrstite
spoj ekspanzione kartice za poleinu kuita rafom.
Korak
7-1 Poveite kablove za unutranje konektore i zaglavlja na matinoj ploi, ukljuujui IDE/SATA konektore i
audio prednjeg panela, USB, IEEE 1394 zaglavlja itd.
7-2 Privrstite modul prednjeg panela (razlikuje se u zavisnosti od dizajna kuita i sastoji se od indikatora
napajanja, indikatora aktivnosti hard diska, zvunika, prekidaa za resetovanje, prekidaa za ukljuivanje
itd.) sa kuita za zaglavlje prednjeg panela (F_PANEL) na matinoj ploi.
Dodeljivanje pinova A:
+MSG- +PW-
+SPEAK-
Dodeljivanje pinova B:
+MSG- +PW-
+SPEAK-
2
1
+HD- -RES+
NC
+PWR-
(Panja) Dodeljivanje pinova za zaglavlje prednjeg panela moe se razlikovati u zavisnosti od modela. Pogledajte
uputstvo za korienje matine ploe za postojee dodele pinova.
Srpski
Korak
Napajanje
Taster za ukljuivanje
DVI-D Port
HDMI Port
D-Sub Port
eSATA Portovi
S/PDIF konektor
IEEE1394 Port
USB Portovi
Audio prikljuak
-4-
Redoslijed pri instalaciji moe varirati ovisno o vrsti kuita i koritenim ureajima. Donje
upute za ugradnju vrijede za GIGABYTE stolna raunala i slue samo kao referenca.
Prouite korisniki prirunik radi detaljnih podataka o matinoj ploi.
Prije ugradnje ureaja, provjerite jesu li sukladni prikljucima na vaem raunalu.
Prije ugradnje ureaja, pobrinite se da budu iskljueni i ureaji i raunalo. Iskopajte kabel
elektrinog napajanja iz zidne utinice, kako biste sprijeili oteenje ureaja i komponenti
sustava.
Raunalni sustav stavite na ravnu i stabilnu povrinu, kako ne bi dolo do greaka u
instalaciji uslijed trenje.
Korak
A. Ugradnja Intel procesora (preskoite ovaj korak ako je procesor ugraen na matinoj ploi)
Ruicu A
Ruicu B
A-2 Uhvatite procesor izmeu kaiprsta i palca. Poravnajte (trokutastu) oznaku kontakta broj jedan s kutom
kontakta jedan na podnoju (ili moete poravnati usjeke procesora s kljuevima poravnavanja) i blago
gurnite procesor na svoje mjesto.
A-3 Kad procesor ispravno ugraen, vratite ugradbenu plou i gurnite ruicu podnoja procesora u blokirani poloaj.
Kad ste propisno umetnuli vrsta B, paljivo vratite ploicu za umetanje. Zatim privrstite ruicu B ispod
jezika za osiguranje. Poklopac podnoja moda e odskoiti s ploice za umetanje za vrijeme postupka
zaglavljivanje ruice. Na kraju, privrstite ruicu A ispod svog jezika za fiksiranje i zavrite ugradnju
procesora.
Detaljne upute o instaliranju procesora potraite u korisnikom priruniku.
-1-
Hrvatski
B. Ugradnja AMD procesora (preskoite ovaj korak ako je procesor ugraen na matinoj ploi)
B- 1 Podignite do kraja ruicu podnoja procesora. Poravnajte
kontakt broj 1 na procesoru s trokutastom oznakom na
podnoju procesora. Provjerite ulaze li kontakti procesora
besprijekorno ulaze u kontakte podnoja.
B- 2 Nakon to postavite procesor u podnoje, postavite prst na
sredinu procesora, spustite ruicu za sputanje i zakljuajte
je u potpuno zakljuani poloaj.
CPU Socket
Kontakti 1
Nemojte silom gurati procesor u podnoje. Procesor nee moi sjesti u podnoje ako je pogreno okrenut.
Prilagodite orijentaciju procesora ako se pojavi taj problem.
NEMOJTE kontakte dirati prstima. Radi zatite podnoja procesora uvijek vratite zatitni pokriva utinice
kad procesor nije instaliran.
Instalacija memorije
Hrvatski
Korak
-2-
Korak
Korak
Jedan prikljuak na matinoj ploi moe se spojiti na dva IDE ureaja. Prije instalacije, provjerite
postavke premosnika (glavni i sporedni) na vaim IDE ureajima.
Ako instalirate vie od jednog hard diska, uite u BIOS Setup (BIOS postavke) i podesite redoslijed
pokretanja raunala.
-3-
Hrvatski
Korak
7-1 Spojite kablove na unutarnje prikljuke i zaglavlja na matinoj ploi, ukljuujui IDE/SATA prikljuke i
audio prednje ploe, USB, IEEE 1394 zaglavlja, itd.
7-2 Spojite modul prednje ploe (varira ovisno o dizajnu kuita, a sastoji se od pokazivaa struje,
pokazivaa aktivnosti hard diska, zvunika, sklopke za resetiranje, sklopke za ukljuivanje, itd.) s
kuita na zaglavlje prednje ploe (F_PANEL) na matinoj ploi.
MSG: Poruka/ LED u pogonu / LED u
mirovanju
PWR: LED u pogonu
2
20 PW: Sklopka za ukljuivanje
SPEAK: Zvunik
1
19
HD: LED aktivnosti tvrdog diska
RES: Sklopka za reset
+HD- -RES+
+HD- -RES+ -CI+ +PWRNC
CI: Chassis Intrusion Header
Zaglavlje otvaranja kuita
(Napomena) Pin dodjele za zaglavlje prednje ploe mogu se razlikovati ovisno o modelu. Prouite korisnike
upute matine ploe za aktualne pin dodjele.
Pin dodjele A
+MSG- +PW-
Korak
Hrvatski
+SPEAK-
Pin dodjele B:
+MSG- +PW-
+SPEAK-
Napajanje
Sklopka za ukljuivanje
Prikljuak za napajanje
DVI-D prikljuak
Prikljuak za HDMI
D-SUB prikljuak
eSATA prikljuci
S/PDIF konektor
IEEE1394 prikljuak
USB prikljuci
Audio utinice
-4-
B:
+MSG- +PW-
+MSG- +PW-
+SPEAK-
20
19
+PWR-
+HD- -RES+
NC
:MSG LED//
:PWR LED
:PW
:SPEAK
:HD LED
:RES
:CI
)( . .
PS/2
PS/2
DVI-D
D-sub
HDMI
S/PDIF
eSATA
USB
IEEE 1394
RJ-45 LAN
-4-
,
, , ,' , .
, ,
.
) (I/O shield ,
) (I/O shield .
) .(I/O shield
.
.
)(I/O shield
.
.
.
PCI Express
,
.
.
IDESATA-
6-1 DVD-ROM.CD-ROM-
"5,25- .
"5,25- .
6-2 IDE.SATA-
, .
IDE- .IDE ,
) master (slave- ) (Jumper .IDE-
, BIOS- .
-3-
. ) AMD (
' 1- . '
) ( ,
.
.
' 2- , ,
.
1
. . ,
.
. , .
' 1- ,
. )
(.
' 2- CPU_FAN-
.
.
.
. . ,
, ,
.
.
GIGABYTE ,
. ,
. .
,
.
.
-2-
. ) Intel (
' 1- :
:A
.
a. , .
b. ,
.
.
:B
'( . B
) A '
) ' '( , . A
. .
B
, .
-1-
.
GIGABYTE .
, .
, .
, .
.
.