LeROI Screw Compressor Performance Program (Ver. 3.0.0.0) 12/15/2006 9:25:58 AM
+eyNQUIRY*#*
‘Natural Gas Services Group Customer Name: PXP
Job No: M06-327 Rev. 1 Site Name: Los Angeles
seas
Gas Name: Specific Gravity: 1.005
‘Mole Weight: 29.110 CpCy: 1.221
Gas Analysis:
Component Mole% Component Mole%
Methane 51.203 Ethane 16.309
Propane 12,932 T-Butane 13,061
Nitrogen 0.990 coz 5.505
***COMPRESSOR***
Model: HGS17222 Internal Ratio: High
Gear Ratio: 2.220 Oil Orifice/Pump: 3/8" orifice
Shaft K (in-Ib/rad): 4.100546 WR? (Ib-f°2): 15:3
Rotor Diameter (mm): 175 Number of Versatro! Ports: 4
—> Max. Allow, Pressure (psig): 300 <—— Maximum Power (hp): 175
Minimum Oil Flow (gpm): 20.0 Max, Discharge Temperature (F): 230
Input Speed (rpm): 1780 Tip Speed (avs): 36
4 *DESIGN CONDITIONS***
Elevation (ft): 500 Atmospheric Pressure (psi
Suction Temperature (F): 80 Discharge Temperature (
Suction Pressure (psig): 5.0 Discharge Pressure (psig): 230.0
Pressure Drop Suction (psi): 0.5 Pressure Drop Discharge (psi): 3.0
Oil Specific Gravity: 0.90 Oil Specific Heat (Btu/Ib/F): 0.48
***DESIGN POINT PERFORMANCE***
Power (hp): 156 Oil Heat Load (Btu/min): 5267
Flow (msefai): 620 Oil Flow (gpm): 46.0
Flow (sefin): 431 Oil Injection Temperature (F): 158
Flow (icfin): 347 Discharge/Injection Temp Diff. (F): 32
‘Mass Flow (Ibm/min): 33.029 ‘Versatrol Ports Open: 0
All power and flow values are +/-5%"
**#NOTES***
-Minimum oil viscosity is 15 centistokes at injection temperature
-Higher viscosity oil may cause higher than predicted shaft power
-Discharge temperatures between 230 F and 250 F are acceptable for
certain applications. Please consult the factory if this condition is required.LeROI Screw Compressor Performance Program (Ver. 3.0.0.0) 12/15/2006 9:25:58 AM
***INQUIRY“**
Natural Gas Services Group Customer Name: PXP
Job No: M06-327 Rev. 1 Site Name: Los Angeles
seeGageee
Gas Name: Specific Gravity: 1.005
‘Mole Weight: 29.110 : CplCy: 1.221
Gas Analysis:
Component Mole% Component Mole%
Methane 51.203 Ethane 16.309
Propane 12,932 1-Butane 13,061
Nitrogen 0.990 coz 5.505
***COMPRESSOR***
Model: HGS17222 Internal Ratio: High
Gear Ratio: 2.220 Oil Orifice/Pump: 3/8" orifice
Shaft K (in-Ib/rad): 4.100546 WR? (Ib-f°2): 15:3
Rotor Diameter (mm): 175 Number of Versatrol Ports: 4
— > Max. Allow. Pressure (psig): 300 <—— Maximum Power (hp): 175
Minimum Oi Flow (gpm): 20.0 Max, Discharge Temperature (F): 230
Input Speed (rpm): 1780 Tip Speed (v/s): 36
«DESIGN CONDITIONS***
Elevation (ft): 500 Atmospheric Pressure (psi
Suction Temperature (F): 80 Discharge Temperature (
Suction Pressure (psig): 5.0 Discharge Pressure (psig): 230.0
Pressure Drop Suction (psi): 0.5 Pressure Drop Discharge (psi): 3.0
Oil Specific Gravity: 0.90 Oil Specific Heat (Btw/b/F): 0.48
**DESIGN POINT PERFORMANCE***
Power (hp): 156 il Heat Load (Btu/min): 5267
Flow (msefa): 620 Oil Flow (gpm): 46.0
Flow (sefin): 431 Oil Injection Temperature (F): 158
Flow (icfin): 347 Discharge/Injection Temp Diff. (F): 32
Mass Flow (lbm/min): 33.029 ‘Versatrol Ports Open: 0
+All power and flow values are +/-5%"*
**#NOTES***
-Minimum oil viscosity is 15 centistokes at injection temperature
-Higher viscosity oil may cause higher than predicted shaft power
-Discharge temperatures between 230 F and 250 F are acceptable for
certain applications. Please consult the factory if this condition is required.