Professional Documents
Culture Documents
Development
January 2016
Barcelona -Spain
Copyright
Copyright SESPID, S.L.2015
All rights reserved.
The program Beam Detailing , and all associated documentation are proprietary and
copyrighted products. Ownership rest with the Structural Engineering Services Platform
for innovation and Development SESPID ,S.L. Unlicensed use of this programs or
reproduction of documentation in any form, without prior written authorization from
SESPID ,S.L, is explicitly prohibited
No part of this publication may be reproduced or distributed in any form or by any
means, without the prior explicit written permission of the publisher.
Further information info@sespid.com
Further support support@sespid.com
ii
DISCLAIMER
CONSIDERABLE TIME, EFFORT AND EXPENSE HAVE GONE INTO THE
DEVELOPMENT AND TESTING OF THIS SOFTWARE. HOWEVER, THE USER
ACCEPTS AND UNDERSTANDS THAT NO WARRANTY IS EXPRESSED OR
IMPLIED BY THE DEVELOPERS OR THE DISTRIBUTORS ON THE ACCURACY
OR THE RELIABILITY OF THIS PRODUCT.
THE USER MUST UNDERSTAND THE BASIC ASSUMPTIONS OF THE SOFTWARE,
ARRANGEMENT OF THE REINFORCEMENT, DETAILING AND THE
REINFORCEMENT ENVELOPES, CONDITIONS AND REQUIREMENT OF THE ACI 318.
THE DRAWINGS AND THE INFORMATION PRODUCED BY THE SOFTWARE MUST
BE CHECKED BY A QUALIFIED AND ENGINEER OR ARCHITECT. THE ENGINEER
OR THE ARCHITECT MUST INDEPENDENTLY VERIFY THE RESULTS AND TAKE
PROFESSIONAL RESPONSIBILITY TO MODIFY OR USE THE PRODUCED
INFORMATION.
iii
Content:
List of Figures ..............................................................................................................................v
1
Introduction .........................................................................................................................6
2.1.1
2.1.2
iv
List of Figures
Figure 1. BeamDetailingInstaller file. .............................................................................. 7
Figure 2. Windows protection message. ........................................................................... 7
Figure 3. Run anyway the Windows protection message. ................................................ 7
Figure 4. Setup Beam Detailing Installer. ........................................................................ 8
Figure 5. Select the Installation Folder path to extract Beam Detailing Package. ........... 8
Figure 6. Install Beam Detailing....................................................................................... 8
Figure 7. Select the start menu shortcuts .......................................................................... 9
Figure 8. Start the installation........................................................................................... 9
Figure 9. Finish the installation. ....................................................................................... 9
Figure 10. Activation keys for the trial version. ............................................................. 10
Figure 11. Installation Folder of Beam Detailing Package. ........................................... 10
Figure 12.Beam Detailing Generator user interface [Not activated yet]. ....................... 11
Figure 13. Trial version activation. ................................................................................ 11
Figure 14.Activation message. ....................................................................................... 11
Figure 15. Activation keys for ETABS and SAP2000 version. ..................................... 12
Figure 16. Commercial license activation. ..................................................................... 12
Figure 17.Online activation message.............................................................................. 12
Figure 18.BeamDetailre ETABS and SAP 2000. ......................................................... 13
Figure 19.AutoCAD support file path. ........................................................................... 14
Figure 20. How to solve the problem of copy and paste the BD-V1.2-ES.DCL file. .... 14
Introduction
This manual is to help the users to install the Beam Detailing Package in Windows systems.
New users must read this document carefully. About how to use Beam Detailing software is
described in the User Manual Document.
This manual provides a guide for the user to install the Beam Detailing package that contains
two software:
Beam DetailingGenerator (BDG): An executable software works in Windows environment.
This software will be installed by running the BeamDetailingInstaller.exe.
Beam Detailer (BD): This software works in AutoCAD environment and will be automatically
extracted in the installation folder of BeamDetailingInstaller.exe
The available versions of Beam Detailing on the website are standalone versions, can be used by
one user on one machine. For any need of a network version, this can be done by sending an
email to support@sespid.com.
Note: Before starting with this manual, make sure you have the BeamDetailingInstaller by
creating an account on www.sespid.com and order the trial version of Beam Detailing
Package.
For any further support you can always send an email with a screenshot of the warning
message to support@sespid.com
Install BeamDetailingInstaller.exe
2.1.1
Figure 5. Select the Installation Folder path to extract Beam Detailing Package.
Beam Detailing must be selected to start the installation as shown in Figure 6
Next step is to select a menu where the shortcut of Beam Detailing will be created as shown in
Figure 7.
The installed version of Beam Detailing is a trial version and must be activated before
activating any commercial version.
The user will receive an email with two activation keys and one order number to
activate the trial version as shown in Figure 10.
10
Click on tools > activate > the window in Figure 13will appear, the activation keys must
be entered as well as the order number> click Activate, the message in Figure 14 must
be appeared. The trial version is now activated.
11
Note: The activation of any version of Beam Detailing (trial or commercial) must be
done online. It means the computer must be connected to the internet during the
activation operation. Otherwise the message in Figure 17will appear. If this message
appeared or any similar message even if the computer is connected, please try again by
closing the software and launch it again.
Note: Trial or commercial license are standalone license and can be used by only one
user on one machine (same machine always).If the user wants to change the machine
where the software is installed, this can be done by sending a request to
support@sespid.com .
12
Beam Detailer software will be extracted in the Beam Detailing installation folder as
shown in Figure 11. BeamDetailer -ETABS and SAP 2000 folder contains the two
main files (two pairs to be used based on the language of AutoCAD) as shown in Figure
18
BD-V1.2-ES.fas can be anywhere in the computer, and must be loaded at each AutoCAD
session. For more help about how to use this software, please read the User Manual
document.
BD-V1.2-ES.DCL must be copied to AutoCAD support path, this path can be like:
C:\Program Files\Autodesk\AutoCAD 2012\Support
For English Version of AutoCAD you have to use the English version of
BD V1.2-ES.fas and BD V1.2-ES.DCL for Spanish Version of AutoCAD you have to
use the Spanish version of BD V1.2-ES.fas and BD V1.2-ES.DCL
For more information about the AutoCAD support file path you can go to Option in
AutoCAD > Files, as shown in Figure 19
13
In case the user couldnt copy and paste the DCL files to the path of AutoCAD support
files, or if the user received an error message during launching the software, next figure
helps to solve this problem.
Figure 20. How to solve the problem of copy and paste the BD-V1.2-ES.DCL file.
14