NINICOLAS
NICOLAS POWER PACK - PP 410
MDE Series
(MDEM — MDEDM — MHDM)
TECHNICAL DESCRIPTION
BUILT-IN COMPACT PP 410 POWER PACK UNIT Complete with:
- Water-cooled diesel engine driving the hydraulic pump set.
- Allcontrols & safety functions
- Hydraulic steering control and titing cylinders
DIESEL ENGINE
~ 800 kW (2000 rpm) EURO 3 MERCEDES BENZ- OM457 hLA
- 11.971 horizontal 6-cylinder high pressure turbo-charged diesel engine
- Closed loop under pressure water-cooling circuit ~ Dry air fiter
- Batteries: 2x12 V/124 Amp/H — Alternator: 28 V. 55 A — Electric Starter: 24 V
- Stainless steel 400! diesel tank
- Air compressor ~ 430V/min ati2 bars
HYDRAULIC POWER
DRIVE PUMP
- REXROTH A4VG 250 (flanged to the engine)
= _ Displacement: 0 to 250 cm3 / 400 bars — Service pressure: 360 bars
BOOSTER PUMP (flanged to drive pump)
~ _ Builds-up and maintain internal pressure
LIFTING & STEERING PUMP
= REXROTH A10VO/3
-_ Displacement: 45 m3 / 350 bars ~ Service pressure: 280 bars
COOLING SYSTEM
= 2x 50KW cooling capacity “honeycomb” Radiators
~ Stainless steel 4001 oil tank — Oil: SHELL T46 or equivalent
- Multi-weather filtration system
CONTROL DEVICES and SAFETY FEATURES
MAIN CONTROL PANEL
1x Heat-up button & ignition key. 4 x Power unit titing control lever
11x Forward / backward drive selector. 4x Horn
1 x Proportional drive / service brake control lever 4 x Low / high-speed selector
1x Engine rate selector (idle/accelerated) 1 x Fuel gauge.
1 x Steering control lever -right/left distributor 1 x Engine temperature gauge
1x Proportional braking contro! push button 11x Tachometer & Hour meter
3x "Suspension-point” control valves 1.x *Lumitext” alarm box
INSPECTION PANEL
3x “Suspension point" pressure gauges. 1x Inner oil pressure gauge.
1x Driving circu oll pressure gauge. 1x Engine oil pressure gauge.
SAFETY FEATURES
- Two emergency stop buttons, one each side of the PPU
- Operation failure detection systems activating one powerful horn
REMOTE CONTROL BOX — 5m cable extension (optional 40 m extension + 2 connectors)
1 x Ignition key.
1x Front & rear translation selector.
1 x Proportional drive / service brake control lever
3 x Lifting control button (one per hydraulic point).
1x Proportional braking contro! push button
OPTIONAL EQUIPMENT
- Drive / Steer electronic synchronisation to operate two or several SPMT from one
remote control box
PP 410 Power Pack, engineered to drive 32 axle lines of which up to 8 axle lines are motorised
CE 2004--PP 410, Subject to modtications Page 1/1OD LAR
maw Muicotas
TECHNICAL DESCRIPTION
MODULE FRAME
-CAD design - High tensile steel
-Main beam & couplings of equivalent strength
High load concentration module structure
-Design safety factor = 2
-Optimised Dead Weight, + 3400kg per axe line
-Optimised ratio Payload / Dead Weight
-Inter module hydraulic assisted coupling (ram)
-2, 3, 4 or more side-by-side configurations
Trailer & semi trailer configurations
-External pneumatic/hydraulicielectric connections
-Comprehensive range of add-on attachments
-Modulle top sealed with non-slippery iron plates
STEERING
-60° eft & right hand steering angles (approx.)
-Full steering angle available in low position
Module integrated steering cylinders
-Mult-hole removable pivoting arms.
-One piece solid central steering bar (no wear)
-Factory pre-set length axle steering rods
-Fast steering modifications
-No special tool for steering modifications
-All ime accessible steering rods — loaded trailer
-All time accessible inner wheels ~ swivel axle
-Detachable headers, 2, 3 & 4 file configurations
MODULE MAIN CHARACTERISTICS TYRES
Width 3000 mm Tires per suspension |: 4— Twin mount
‘Minimum Loading Height 635 mm. Tires per axle ine 8
‘Running height 1160 mm Tite size : 216/75 R17.5 - tubeless
‘Maximum Height £1490 mm
WHEELS
‘SUSPENSIONS -Reinforced discs wheels
“Hydraulic type “Twin mounted
-650mm suspension stroke: +/-325mm
-Important slope correction ability PNEUMATIC SYSTEM
Important road cant correction
-Special cast arms & forks — Nicolas design
-Rotating at 180° for service or tyre exchange
Type 2Pendulum
Stroke, 650 mm
Number per Line 22
Safety device 1 per Suspension
Suspension pivot:
-Secured to the module by means of screws
-Easily removable for maintenance
-Designed and sized to absorb and take vertical and
radial stresses insuring: long life of parts.
Suspension fork:
-Extra wide design avoiding interfering torsions.
“Sealed articulations,
Suspension cylinder:
-Large lower seif aligning spherical ball joint ensuring
permanent upright alignment of axle fork and
suspension main arm
-Anti-splash protection
Hydraulic system:
-Hose failure safety device — one per suspension
-One double valve selector block per suspension
-3 or 4 point suspension settings
-Hose quick coupler connections
Oscillating Axles:
-Fitted with conical roller bearings
-Sealed protected oscillation assembly
CE01/09 MHD ~ Technica description 272 — subject to modiications
-Two independent air circuits
Service brake on every suspension
-Parking brake,
-Emergency brake
-Drum diameter: 305 mm
-Width of linings: 150 mm
-Double diaphragm vessels — service brake
-Spring chamber vase — parking brake
FINISHING
-Shot blasting, S.A. 2.5 Swedish scale
Primary undercoat
-Two coats of polyurethane paint
-One coat before assembly
-One coat after final assembly
-Colour &/or specific paint available on request
OPTIONAL ADD-ON ATTACHEMENTS
Too! kit & 1" emergency parts set
-Ausiliary power packs: 9.5 /17.5 /22 / 29.5 kW
Standard & special decks
-Active goosenecks — 3% removable coupling pin
-Trailer pull & push bars
-Modular & extendable KBN beams
~100 to 500T capacity shallow bolsters
-Rear bolster synchronised steering system
-Gustom made girder beams
-MHDM motorised modules:
-75 to 300 kW Diesel Power Packs (PP)
-Synchronised control of several PPNWnico.as
11703325
‘en charge /Toaded
Module specification Zaxeline | Saxleline | Gave line
‘Overall length 6 200 7750 9.300
Overall width 3.000 3000 3.000
Mini loading height 835
Maxi loading height 1 485
Average rolling height 1460
‘Suspension type ~ Stroke. Hydraulic — Pendulum — 650mm,
‘Suspension setting & safety ‘According to configuration — each axle
Steering Built-in hydro-mechanical system
Braking Standard non motorised axles
‘Standard Motorisation Riype
Hydraulic motors per axle 2 2 2
Mortised axle lines (standard) 3 4 5
Hydraulic Motors — Type REXROTH — A6VE
‘Axle Reducers ~ Type LOHMANN — GFT
Technical capacity per axle line 347 al 0 ~ 3 km/h ~36T al 1 km/h
range ‘Oto Skm/h (Up to 15kmih as an option)
Traction force per axle line Up to 14 200 daNv
Tires 215/75 R 17.5 or 7.50R 15
‘Standard Power packs ‘Standard capacity & performances
PP 410 MERCEDES engine OM 457 hLA : 300 KW
Maxi configuration Up to 32 axle lines (8 drive! maxi + 24 driven’)
PP 200 DEUTZ Engine BF6M 20120 : 147 kW
‘Maxi configuration Up to 14 axle lines (4 drive’ maxi + 10 driven’)
MHD Series SPT - 2005 subject to modtications Page v1HO Ae NICOLAS
[ 775 1550 1550 75.
TECHNICAL DATA
Platform width — mm ‘3000 Steering angle [60° approx.
Platform height, laden—mm [1160 #/-325 |Suspensions | Hydraulic, pendulum type
‘Minimum loading height —mm_| 835 Wheel base —mm|1 550
‘Suspension stroke — mm 650 ‘Axle track—~mm_| 735
Technical capacity /axle line | 36T (metric) | Tires —twin mount |215/75R17.5 — tubeless
Technical capacity per axie fine — tonne | _ 18 9 26 34 36
‘Speed — Km/h (approx) 62 40, 20 5 1
Module type-MH__| 2-axle line | 3-axleline | 4-axleline | S-axleline | 6-axle line
‘Module width 3.000 mm
‘Module length 3i00mm | 4650mm | 6200mm | 7 750mm | 9300mm
Dead Weight 7.6 10.9 142 17.5 20.8
Payload at 62 krm/h 28.4 43.4 57.8 72.5 87.2
Payload at 40 km/h 30.4 46.1 618 775 93.2
Payload at 20 km/h 44.4 67.1 09.8 112.5 135.2
Payload at 05 kra/h 60.4 O14 121.8 152.5 183.2
Payload at 01 kra/h 64.4 ‘97.4 129.8 162.5 195.2
‘CEO1708 MAD — Technical description 172 — subject to modfcatons
Tg NICOLAS INDUSTRIE S.A.S -B.P.5-FLN.6- 89290 CHAMPS SUR YONNE w 93 /08.86:53.52.00
a E-mall: sonst Intamet: ses goa
ROAD TRANSPORT AND SPECIA. HANDLING MATERIAL » ENVIRONMENT « SERVICEjoteur_/ Engine MERCEDES OM 457 HLA (300 kw 8 2000 tr/mn)}
BT | bf Bote de répartiton / Dividing box STIEBEL 4380 / SAEI (2 sorties)
{ TI|Pompe de tronsiation / Driving pump REXROTH A4VG250 DA2D2/32
Pompe de servitudes / Accessories pump REXROTH AT0VO45 DFRI
‘ompe pour aérorétrigérants / Pump for coolers CASAPPA PLP30.27/20.20
féservoir 2 gas—oll / fuel Tank Gopacité / opacity = 3101
jac 8 hulle / oll tank Gopacite / Capacity = 4801
| 'gatterie / Battery 212 V ~ 124 Ah)
LIFE] L Aternateur / alternator ISKIA 0705 (28 — 55 Amp)
RL a{ir Aérordtigérants: 7 Coolers —— EDH E2-044 (2x35. kw)
#[ Groupe de puissance pour module
28 lignes de 2 essieux MAXIMUM
Power unit for a module of
28 lines of 2 axles MAXIMUM
GROUPE : PP410_ MHDM
NNICOLAS [ovis 2
* MASSE : 5700 KG (chassis groupe : kg)
(chassis traverse : kg)