1. Product Specification
RFID Card Aecee Control Opening anon, 1
ode ie 5, card os wll be 16
Delete card
Delete by index code
Press [7]
++{3-digit code! (2 beeps)
++{3-digit code2} (2 beeps)
+[3-digit coden] (2 beeps)
+1*](2 beeps)
5.4.2. Delete by presenting card
Press (7)
[Presenting Card1} (beep, 2 beeps)
+[Presenting Card2] (beep, 2 beeps)
+[Presenting Cardn} (beep, 2 beeps)
+04. beeps)
5.4.3. Delete all cards
Please restore the factory default
$44. The private pin will be deleted when
the card is deleted
5.5. Ealt programming mode
Press [*] (2 beeps)
EID CardAccen Conl Unt Operating arsine 3
3. The LED an Buzzer
3. 1.Normal mode:
3.1.1. Valid command: Short beep
3.1.2 Invalid command: Long beep
3.2 Programming mode:
3
3
2.1. Green LED on
2.2.Valid command: Two short beeps
3.2.3. Invalid command: Three beeps
4. Cancel Command
Press the [#] key to cancel comand,
5. Funetions and Setup
5.1 Enter the programing mode
Press [#]+[6-digit pin) Default is 990101)
5.2.Modify the programming pin
Press [0]
+{now 6-digit pin]
+Cconfirm the new 6-digit pin)
3, Enroll card
Press [5]
“4[3-digit index code} 2 beeps)
“{Cardi] (beep, 2 beeps)
*{Card2] (beep, 2 beeps)
“{Cardn] (beep, 2 beeps)
#0712 beeps)
‘53.1 3nigit index code: range from
FID Cad Acem Contr Lit Opening acon, ni
5.6. Set up door
5.6.1
mode
‘or pin mode
Press (1]+{0] (2 beeps)
5.6.2. Card + private pin mode
Press (1}+(1] (2 beeps)
5.7. PINS
‘The pin in “Card or PIN mode is either
the public pin or private pin (at most 500).
5.7.1. Disable changing private pin
Press (1]+{2] (2 beeps)
5.7.2. Enable changing private pin
‘ress [1]#[3] (2 beeps)
5.7.3. Change private pin
Press [1] (2 beeps)
+[Presenting card) (beep.2 beeps)
+[4-digit old pin} (2 beeps)
++[4-digit new pin}
+[confirm the new pin] (2 beeps)
5.7.4. Change public pin
Press (3]4{4-digit pin] (Default 1234)
When the public or private pin is 0000,
the pin is void in "Card or pin” mode,
Change door open time
Press (2]+{1T]
‘TT is the time interval in seconds. For
example, if the door open time is 3 seconds,
then PIa3,
" 410. Wiring
10.1. With normel power supply
bor
10.2. With access control power supply
Fo
prechh
Pee ae
SSe55
FID CarkAces Conte! Ut Opening nsttins 7
59, Anti-bresk
= $9.1. Disable an-break: Press [4}+(0]
59.2. Enable ant-beak: Press []+(1]
5.10, Door contact sensor
510.1. Disable door sensor: Pros [6}+{0]
5.102. Enable door sensor: Pres (6)+{1]
SL, Door sensor alarm
SILL, Disable alarm: Pres [8}(0)
5.112. Babe alann: Press [8}(1]
‘fer turning on this funtion, the controler will give off
continuous lng beep when the doors no clsed after normal
opening, o the door is not opened through the controller.
S112. Alarm delay time
Press (82}+[TT]
‘TT ste time itera in seconds For example ifthe delay
time is 3 seconds, then T=,
‘When door is locked TT seconds if the door contact
sensor it in alam stats, the contol i im alarm mode.
‘This function shold be used when the door sensor alarm is on.
6. Restore factory default
ress [86]. There will be 2 beeps, 3 beeps and 3 beeps
ater S seconds, then the factory defaults are restored.
1.User's instruction
7.1.Card or PIN mode
7.1L The pins should be entered in 2 seconds
7.1.2.Press [*] key to cance pin input
72.Card + Private PIN mode
REIDCwd Aces Cont Unt Opening nsmctins 5
Eagracee
RFIDCwdAccssConolUnt Opemtigtosnctaas —
72.1 Reading card}+enter 4 pin] to open
72.2 Press [*] key to cancel pin input
FID Card Access Conti Opting suction, 6