Technical Data
Penguard Express
Product description
Penguard Express is a fast drying, high solids two-pack epoxy coating which may be appled in high film thickness and
at lower temperatures.
Recommended use
‘As an anti corrosive primer andlor intermediate co‘
athmospheric exposure where fast dry-to-recoat and
‘systems of primers and topcoats.
for corrosion protection of stee! ard other substrates in
dry-to-handle times are desired. Can be used alone or in various
Film thickness and spreading rate
Minimum — Maximum —Typleal
75 250 2
100 240 170
ing rate (mA) 99 3 56
Physical properties
Colour Grey, Red, Buf, Light Red, Turquoise
Solids (vol %)* 7442
Flash point 32°C £2 Setattash)
voc 290 gma UK-PG8I23(07). Append 3
Gloss Fiat
Gloss retention Fair
Water resistance Very good
Abrasion resistance Very good
Solvent resistance t
“Measured according to ISO 3233:1998 (E)
Surface preparation
‘All surfaces should be clean, dry and free from contamination. The surface should be assessed and trested in
accordance with ISO 8504.
Bare steel
Cleanliness: Blast cleaning to Sa 2%4 (ISO 8501-1:2007). Roughness: using abrasives suitable to achieve grade Fine to
Medium G (20-85 ym, Ry5) (ISO 8503-2)
‘Shopprimed steel a ~~
Clean, dry and undamaged approved shopprimer. 7 \
Penguard Express Page 1 of 3Coated surfaces
Clean, dry and undamaged compatible primer. Please contact your local Jotun office for more information
Other surfaces
‘The coating may be used on other substrates. Please contact your local Jotun office for more information.
‘minimum -5°C and at least 3°C above the dew point ofthe air, temperature
is required in confined areas to ensure
proper drying. The coating should not be exposed to ol 3 stress until cured
Application methods
Spray Use airless spray
Brush Recommended for stipe coating and small areas, care must be taken to achieve the specified dry
film thickness.
Application data
Mixing ratio (volume) at
Mixing 4 parts Comp. A (base) tobe mixed thoroughly with | part Comp. B (curing agent)
for 10 minprorto use.
Pot ite (23°C) 2 hours. (Reduced a higher temp.)
ThinneriCleaner Jotun Thinner No. 17
ing data airless spray
Pressure at nozzle 15 MPa (160 ko/om* 2100 psi)
Nozzle tip 0.46 - 0.69 mm (0.0'8-0.027")
Spray angle 40-60"
Fitter CChack to ensure that fiters are clean
Drying time
Dying times are general elated to ar crcustion, temperature fim thickness and numb o coats, and willbe
affected correspondingly, The figures given in the table are typical with
* Good ventilation (Outdoor exposure or free circulation of ai)
+ Typical film thickness
+ One coat on top of inert substrate
Substrate temperature orc ec tore
Surface dry 16h 1th 4h 2h
‘Through dry 38h 24h ton oh
Cured : 21d Bd 8d
Dry to recoat, minimum 24h 14h Bh 4h
Dry to recoat, maximum !
Substrate temperature 40°C
‘Surface dry Osh
Through dry 2h
Cured 3 ~
Dry to recoat, minimum th
Dry to recoat, maximum *
Penguard Express Page 2 of 3‘applicaticn, there Is normally no
subsequent coat is applied before
ht for some time, special attention must
3nd mattening/removal ofthe surface layer in order to obtain good adhesion
bbe paid to surface cleanin
idelines only. The actual drying timerimes before recoating may be shorter or
rent for early handling and
meters and special
The given data must be considered as
longer, depending on film thickness, ventilation, humidity, underlying paint system,
mechanical strength etc. A complete system can be described on a system sheet, wher
Conditions could be included
Typical paint system
Barrier 41x50 um
Penguard Express 1150 pm
Hardtop ASiHardtop XP 4x50 um (Dry Film Thickness)
Penguard Express 2x125ym (Dry Film Thickness)
Hardtop ASiHardtop XP 4x50 ym (Dry Film Thickness)
‘other systems may be specified, depending on area of uso
Storage
“The product must be stored in accordance with natonal regulation, Prefered storage cendtons are to keep the
containers n'a dy space provced wih sdequate vetlaton. The containers should be sealed toh
Handling
Handle with care. Str well before use
Packing
“6 ives Comp, res Comp. B (curing
Altres Comp. (base) in a res Comp. 8 (curing 29
information on the health and safety hazards and precautions for use cf this product, we refer to
torial Safety Data Sheot.
DISCLAIMER
‘The information in this data sheet is given to the best of our knowledge based on laboratay testing and practical
experience, However, as the product is often used under conditions beyond our control, we cannot quarantee anything
but the quality of the product itself, We reserve the right to change the given data without notice.
eet local Jotun address
Jotun is @ World We company vith factories, sales offices and stocks in more than 50 counties. Fer you
lease contact the neerest regional office ov our webste at wawotun.com
ISSUED 6 DECEMBER 2007 BY JOTUN
‘THIS DATA SHEET SUPERSEDES THOSE PREVIOUSLY ISSUED
Penguard Express Page 3of 3Breuer ere Bott
Hardtop XP
Product description
Typical use
Marine:
Recommended for topside, deck and superstructure.
Protective:
lants, bridges and bullcings. Suitable for a wide
Approvals and certificates
NORSOK System 1, Rev.5
Low flame spread certficate according to IMO/Solas directive.
Other variants available
Hardtop XP Alu
Hardtop XPL_
Hardtop XPF
Refer to separate TDS for each variant.
Colours
according to colour card and Mul
‘olor Industry tinting systen (MCI)
Product data
Test/Standard Description
150 3233, 632%
1s0 2613 loss (70-85)
Flash point 150 3679 Method 1 30°C
Specific gravity calculated 1,22 kg/l
VOC-USA / VOC Hong Kong EPA Method 24 336 g/l
VOC-Solvent Emission Directive SED (1999/13/EC) 260 g/kg
The provided data Is typlcal for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss level: According to Jotun Performance Coatings' definition,
Date of issue: 1 August 2014 z by Jotun Group Page: 1/5
Data Sheet supersedes those praviousy issued.
TDS) is recommended tb a9 ny. cfuncton
{he produc. For your nearest cea Sakon office,
ch the Safety Data Sheet (SDS) and the
age visit our website at ww Jotun.comTechnical Data Sheet
Hardtop XP
SY
Recommended film thickness per coat
Film thickness and Dry film thickness Wet film thickness
spreading rate
(um) (um) (m/l)
Minimum 50 80 12,6
Maximum 100 160 63
Typical 60 95 10,5
Surface preparation
To secui 19 adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.
Surface preparation summary table
Surface preparation
Substrate Minimum Recommended
‘and undamaged
le coating (150 12844-4 6, co
y
n, dry and undamaged
Coated surfaces
ible coating (ISO 12944-4 6.
Application
Application methods
‘The product can be applied by
Spray’ Use airless spray or conventional spray.
Brush: Recommended for stripe coating and small areas. Care must be taken to achieve the
specified dry film thickness.
Roller: May be used. Care must be taken to achleve the specified dry film thickness.
Product mixing ratio (by volume)
Hardtop XP Comp A 10
Hardtop XP Comp B a
Thinner/Cleaning solvent
Thinner: Jotun Thinner No, 10 /Jotun Thinner No. 26
Jotun Thinner No, 26 is supplied and used in USA due to legislation.
Guiding data for airless spray
Date of issue: 1 August 2014 by Jotun Group Page: 2/5
th the Safety Dats Sheet (SDS) and the
's recommended te bp pad in consunetion
fe ok wiv.jotun.com
product. For your nates fal Jotun office, please visit our wetTechnical Data Sheet
Hardtop XP
Ne el
Nozzle tip (inch/1000): 13:19
Pressure at nozzle (minimum) 150 bar/2100 psi
Guiding data for conventional spray
Nozzle tip (Inch/1000) 14-19 (HVLP) /- 1.1-1.9 mm (pressure pot)
Pressure at nozzle (minimum): 2.1 bar/30 psi (HVLP) / 2.4 bar/30 psi (pressure pot)
Drying and Curing
‘Substrate temperature S°c 10°C 23°C 40°C
Surface (touch) dry 1h 6h 35h 2h
Walk-on-dry 24h 14h 7h 4h
Dried to over coat, minimum 2h 4h 7h 4h
Dried/cured for service aid id 74 3d
Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and.
within the DFT range of the product.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness. Dry sand sprinkled on the surface can be brushed off without sticking to or causing damage to the
surface,
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
Imprints or other physical damage.
Dried to over coat, minimum: The shortest time allowed before the next coat can be applied.
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
‘environment/mediur
Induction time and Pot life
Paint temperature 23°C
Pot life - - 15h 7
Heat resistance
Temperature
Continuous
Dry, atmospheric 120 °c :
Peak temperature duration max. 1 hour.
‘The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Date of issue: 1 August 2014 > by Jotun rode Page: 3/5
‘is Tecnica Data Sheet supersedes those previo ssh
‘Tre Tecate sheet 10S) s recommended to be ren Zijuncion win the Safety Daa Shes (SDS) an the
Topicton Guts (0) for lis prosuc For Your eared cal otun of, ese wet oor mete twa fn.Technical Data Sheet
Hardtop XP
SN
Product compati cy
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Previous coat: epoxy, zinc epoxy, epoxy mastic, polyurethane
Packaging (typical)
Volume Size of containers
(tres) (litres)
Hardtop XP Comp A 4.55 / 18.2 5/20
Hardtop XP Comp B 045 / 1.8 1/3
‘The volume stated is for factory made colours. Note that local variants in pack size end filled volumes can vary
due to local regulations.
Storage
‘The product must he stored in accordance with national regulations. Keep the containers in dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be ket tightly closed. Handle
with care,
Shelf life at 23 °C
Hardtop XP Comp A 48 month(s)
Hardtop XP Comp B
ation, Tre above is minimum shelf
some markets commercial shelf life can be dictated shorter by local le
fe, thereafter the paint quality is subject to re-inspection.
Caution
Ibe trained, experienced and have
id according to Jotun's technical
protection equipment when using this,
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for aprroval before commencing
the work.
Health and safety
‘not inhale spray mi
cleanser, soap and
Date of issue: 1 August 2014 < by Jom foun Page: 4/5
' recommended tober h-confinction withthe Safety Data Sheet (SDS) and theTechnical Data Sheet
Hardtop XP ~ etm Protects Property
el
jons from batch to
Products primarily meant for use as primers and antifoulings may have slight color var
bateh. Such products may fade and chalk when exposed to sunlight and weathering
Disclaimer
“The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
Used under conditions beyond Jottun’s control. Jotun cannot guarantee anything but the quality of the product
Itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
‘and specific application practices.
If there is any Inconsistency between different language issues of this document, the English (United Kingdom)
Date of issue: 1 August 2014 by Jotun, Group Page: 5/5
‘This Technical Data Sheet supersedes those previoustyissubd
The Technical Data Sheet (TDS) is recommended to be readin conjunction with the Safety Date Sheet (SDS) andthe
Aoplcavon Guide (AG) for ths product. For your nearest local tun oie, please vist our Website at ww JomUn.com