Professional Documents
Culture Documents
Tpa 3003 Circ Alignm
Tpa 3003 Circ Alignm
~ TANDBERG
Power Amplifier 3003 Circuit Diagram and Alignment Instructions
-
-
--
TANDBERG - The European Alternative
ALL BOARDS ARE SEEN FROM THE SOLDER SIDE
-
Power amplzfier board, left channel
Power amplifier board, right channel
® c i
J 311 te:!l
Power supply board
E
Output power amplifier board
Adjustments
Peak clipping
Quiescent current
• Connect an oscilloscope to left/right speaker output across 8 ohms load.
Test condition:
Approx. 10 min. warming up time from cold condition without signal applied.
• Apply a 1 kHz signal and drive the amplifier to just below clipping point.
• Connect a VTVM across R203/R204 for left/ right channels respectively, i.e. between the top terminals of R203 and R205/R204 and R206, see figure.
• Adjust R127/R128 (.) so that the Peak Clipping indicators on the front lights up. Then fine adjust the potentiometers down until the lights just goes off.
• Adjust Rll 7/R1l8 (+ ) for 40 m V reading on the VTVM.
- •• ~ FRONT
Measuring point, quiescent current.
7SV
SlV
1
j
I I b
~N~'~rr~~ C101
:ti.c I: 10J.l
A(1
I .
I
I
I
I I I
r ------ -J;;I
I 11205 I
I MJI~U I
I I I
~ I
~ I
J20S1
A:
A:
1 V
34.6 V / 8 ohms
~---------------~~------~
~ ~J210~4~ __
011.t, J 106 I
N o N 0' U
~
0' U
tt.
Circuit diagram
• Quiescent current
• Peak clipping
--- -J;;;;l
~ I
1
1
1
I 1 ,-----~~
~ 0 1
0
~~ ~ z I
, o~
0 N~
, 0'0' nasi
'< J I
~ < om
NW ~ I
,. 0'00 ~
0 ~ I
1 0'
U
3 - I
~
~ I
I
I
I
____ J~ N o
+ SOmY
FUSE 230V T 4A 115V TSA
I !
1 ~ C_--_-_.- -- ~- --------~- -~-----------------------------------------l
: J §: ~~,~ ,,:' I ~~
H~~I8 ~ ~ c :
I" - ~.J.::IJ i'l~ ,
r I J 315
'I
2.2N 41'S
[J
r~ER Lpoon
:- --J-]
F=~== ~
I L_ I
I I
L _j
I I
L .J
........ SO/60Hz SOOW
115V/ 230 V
L ,
POWER SUPPLY
I
I I I I I
~Q ~ J20J I ~~
-r---+-~~r-4=';-1 --+---++----++<:1 J 312
r ~W ~ I I
1 5 I
I I
1 I
I I
I I
I ~-----------------------~
:;[ :
~~ ,
@ 23.BV:
Q 305 :
Be 557 \
,
, , , , , ,
B B C
EQC E~C B~E ~ ALL TRANSISTOR
NPN: Be 40 lSAS1SY MJE 15030131 ARE SEEN FRO M
Be 5t. 7 SF 381 UNDERNEATH
i Be Sl8 MJE 15022/23
PNP: Be 4l.8
BC 557
Be sse Dismantling
• Top cover, rear (1)
• Top cover, front (2)
• Rear panel (3)
• Front panel (4)
• Bottom cover (5)
2
\
Dismantling the rear and top covers.
5
Dismantling the front and bottom covers.
3
Service hints
Checking the shortcircuiting protection circuit
• Connect an oscilloscope across R203/R204 for left/right channels respectively, i.e. between the top terminals ofR203 and R205/R204 and R206 see figure.
• Shorteircuit the output terminals (+ to -).
• Apply a signal of 0.1 V to the input terminals.
• The oscilloscope should then show the following picture:
•
FRONT
Checking the shortcircuiting protection circuit.
Checking the speaker protection relay
What to check after replacement of power transistors
If some fault occurs in the output power circuits, causing d.c.-voltages at the speaker outputs the relay should disconnect the speakers to prevent damage.
After having replaced a defective power transistor the following components should be checked with an ohmmeter and replaced if necessary.
• Disconnect white wire from the output transistors at terminal J 311, see figure.
The component numbers refer to the left channel.
• Disconnect speaker load.
R157/159 R161/163 R209/211/213/215 R201/203/205/207
Q109 QI23/125/115/117 CRI09-117 CR121/123
• Apply 6 to 8 V d.c. (+ and - alternately) to J311. The relay should then open.
The power supply board seen from the component side.
Tandberg Power Amplifier TPA 3003
Technical Data
Dimensions:
17 1/8" (43.5 em) 13 %" (35.0 em) 3 Yo" (8.3 em) 25 Ibs (11.3 kg)
0.05 -
rminals.
0.1-
Power requirements:
115/230 V ± 10%,50/60 Hz
ollowing
Power consumption:
50 -now
Width:
Depth:
Height:
Weight:
0,02 -
0,01 -
0,005 -
0,002 -
Technical Data according to IHF-A-202, 1978
I
0.001 - ,+
L--+---- ------t- --+----t -7---+rrt+
, 1 I ' • \ ~ , .o't
250mW 1 W
---..----->- .. ----+-+-+t-+i---------+-----+--I---t--+-++++t-------.----+______!
, ). ~ ~ '8 9, I I
lOW wow 150W/8ohms
Continuous Average Power Output:
(8 ohms, 20 - 20,000 Hz, THD < 0.02%)
2 x 150 W
Total harmonic distortion versus output power
Dynamic Headroom:
0.35 dB
RaNT
Frequency Response:
20 - 20,000 Hz, + 0/- 0.2 dB
SensitivitV:
1 V
A·weighted Signal-to-Noise Ratio: (Ref. 1 W/8 ohms)
Other Technical Data
98 dB
Frequency Response:
5 - 100,000 Hz, + 0/-1.5 dB
Output Impedance (20 - 1000 Hz):
0.04 ohms > 70 V(us
Slew rate:
Secondary Disclosures
A-weighted Signal-to-Noi.e Ratio: (Ref. 150 W/B ohms)
120dB
Clipping Headroom:
1.05
sr
Output Impedance (20·20,000 Hz):
0.08 ohms
Wideband Damping Factor:
100
• Specifications are subject to change for further improvement without notice.
transistor hecked essary.
Low Frequency Damping Factor:
200
SMPTE Intermodulation Distortion:
0.02%
IHF Intermodulation Distortion:
0.02%
tchannel.
Transient Overload Recovery Time;
Immeasurable
Reactive Load Facto.:
1.2
Reactive Load Rating:
0.8 dB
Optional Extras
/
'115/117 . 7
3
Separation:
> 75dB < 0.1 dB
Black acrylic side walls for freestanding units . Attachment sets for installation in 19 inch racks.
Difference of Frequency Response:.
TANDBERG
The European Alternative
Tandberg AIS, Post Office Box 55, Bogerud, N-Oslo 6, Norway
1724-5-80 PartNo,714134 Printed in Norway by Reclamo A/S