Professional Documents
Culture Documents
Gate Paper 2008
Gate Paper 2008
www.gateforum.com
6 13 20 27 34 41 48 55 62 69 76 83
D B D D B B C
7 14 21 28 35 42 49 56 63
D C D C B
C D B
70 77
84
3.
4.
5.
1 2 4 Given matrix is 3 0 6 1 1 P
Let 1 , 2 and 3 be the Eigen values of the above matrix Let 1 = 3 ( Given)
Now, 1 + 2 + 3 = sum of diagonal elements = 1 + P 2 + 3 = P + 1 3 = P 2
6.
Given vector is F = ( x y ) + ( y x ) + ( x + y + z ) k i j
Divergence =
F F F + + = 1+1+1 = 3 x y z
8.
Both youngs Modulus and shear Modulus are required as linear strain will be calculated by young modulus. Change in diameter can be calculated from Poissons ratio which depends on youngs modulus and shear modulus.
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission. Discuss this questions paper at www.gateforum.com. 1
R
0.5
www.gateforum.com
P
20
75Kg
11.
Grublers criterion is applied to mechanism with only single degree of freedom. Given conditions satisfy Grublers criterion i.e. 3 2j 4 = 0 where,
= link, j = No. of joints
13.
14.
Prandtl Number, Pr =
CP 0.001 1 103 = K 1
18.
Job with higher Processing time will be taken first since it will minimize the total holding cost.
21
21.
I=
2
00
xydxdx
1 2
(0.1)
x2 x 2 dx = 4 = 1 0 0
0
2
y2 2 xdx = 0 0
(2.0)
22.
i Gradient will f =
i f = 2x + 4yj + k
F F F +j +k x y z
Now f at the po int (1,1,2 ) f = 2i + 4j + k Directonal derivative of f in the direction 3i + 4k is = (2i + 4j + k ) . (3i 4j)
2
3 + ( 4 )
6 16 10 = = 2 5 5
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission. Discuss this questions paper at www.gateforum.com. 2
www.gateforum.com
1 + nyxyx 1 yx 1 ( x ny + 1) y Now x = 2, y = 1 = yx So 2 f =1 xy
29.
y + 2y + y = 0 D2 + 2D + 1 = 0
i.e. (D + 1) = 0,
D = 1, 1
So solution will be y= ( C1 + C2 ) e x Now given, y=0 at x=0 and y=0 at x=1 So we get C1 = C2 = 0 y = constant y ( 0.5) = 0 32.
Let FS be the shear stress
T =
fs d3 fs = 51MPa, 16
82MPa
34.
At node P
TPQ cos 45 + TPR cos 60 +F = 0........ (1) TPQ sin 45 = TPR sin 60.................. (2 ) from these two equations we can find out TPQ and TPRin terms of F. Now, At node Q. TQR = TPQ cos 45 On solving we get, TQR = 0.63F
Q
45 30
F P TPQ
45 60 TPR
R
ooo
TQR
35.
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission. Discuss this questions paper at www.gateforum.com. 3
www.gateforum.com
39.
K1 =
G.d14 8D13.n1
& K2 =
G.d24 8D23.n2
56.
Direction of heat flow is always normal to surface of constant temperature. So, for surface P ,
dT = 20 K / m dy
63.
Riser takes care of solidification/contraction in liquid state and phase transition. So volume of metal compensated from the riser = 3% + 4% = 7% Heat supplied by power source = Heat required melting efficiency transfer efficiency welding power = cross sectional area welding speed 10 .5.72103 = 5 10 V V = 14 mm / s
67.
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission. Discuss this questions paper at www.gateforum.com. 4
www.gateforum.com
41.
Th,o Tc,i
82.
s = 250MPa. V = 180m / min, F = 0.20mm / rev r = 0.5, = rake angle = 7 = shear angle r cos = 28 1 r sin Now shear force tan = Fs = wt1s sin w = depth of cut = 3mm, t1 = feed = 0.02mm
Fs = 320KN
83.
cos ( + )
FS cos ( )
All rights reserved by GATE Forum Educational Services Pvt. Ltd. No part of this booklet may be reproduced or utilized in any form without the written permission. Discuss this questions paper at www.gateforum.com. 5