Professional Documents
Culture Documents
FIM3040LV Data Sheet
FIM3040LV Data Sheet
NITGEN FIM30xx
Datasheet
Preliminary
Version 1.05
FIM30xx
Serial Number:
FIM30xx
Revision History Date of Revision 2006-05-15 2006-07-11 2006-07-25 Version 1.00 1.01 1.05 Release FIM3030-HV added
Description
FIM30xx
1. General Descriptions
FIM30xx is a low-price stand-alone Fingerprint Identification Device with many excellent features. It provides benefits such as high identification performance, low power consumption and RS-232 serial interface with the various commands for easy integration into a wide range of applications. It is a durable and compact device with fingerprint identification module containing NITGEN optics-based fingerprint sensor inside.
2. Target Application
Door-lock system Safe Box Simple Access Controller Vehicle Control ATM , POS And more
FIM30xx
3. Basic Feature
Hardware Specification ITEM CPU Board DRAM Spec. Flash ROM Dimension Sensor Supply Voltage Current Consumption Operating Temperature Humidity ESD Tolerance Communication Channel External I/O FIM3030-LV FIM3040-LV
FIM3030-HV
FIM3040-HV
ADSP-BF531 8Mbyte SDRAM 1Mbytes 43 x 60 [mm2] OPP03 OPP04 OPP03 OPP04 5.0 0.5 [V] 3.3 0.3 [V]
(Idle) 55 ~ (Op.) 210 [mA] (Idle) 60 ~ (Op.) 200 [mA] (Idle) 55 ~ (Op.) 210 [mA] (Idle) 60 ~ (Op.) 200 [mA]
-20 ~ 60 [] ~ 90 [% RH] B/D: 10 [KV] (indirect) Sensor Finger contact Area: 20 [KV] (air) RS-232 Speed: 9600 ~ 115200 [bps] 3 Key Input 2 Result Output
Operation Specification FIM3030-LV/HV FIM3040-LV/HV 0.2(normal) / 0.7(secure) sec 1.0 [sec] (Capture + Extract + Match) Max. 0.5 [sec] AES for saving data
ITEM Capture Speed Verification Speed (Normal Mode) Boot Up Time Data Encryption Method
FIM30xx
4. Block Diagram
I2C NITGEN NITGEN Fingerprint Fingerprint Sensor Sensor OPP03 OPP03 SCLK DATA Hsync Vsync PixClk CPU CPU I/O I/O
Memory Memory
FIM30xx
RS-232C communication data consist of 8-bit data, no parity, 1-bit start-bit and 1-bit stop-bit.
FIM30xx
5. Operation
Communication
FIM30xx has RS-232 serial communication port through that FIM30xx communicates at the same time. These ports support 6 baudrate modes such as 9600, 14400, 19200, 38400, 57600, and 115200 bps. FIM30xx follows NITGEN Serial Communication protocol. For more detail information refer to the document NITGEN_ComProtocl.pdf.
User Data Area FIM30xx provides 64 Kbytes flash memory. Using this memory, host can save private data for specific usage. The caution is needed because the responsibility for reading, writing and erasing user data area is given to the host.
Key Function FIM30xx supports 3 function key inputs such as Enroll_Key, Delete_Key, and Identify_Key. Using these keys without serial communication, enrollment, deletion, all deletion and identification operating can be executed. The following timing diagram and table show the operation condition of keys.
Signal
tactive
FIM30xx
FIM30xx
6. Technical Data
6.1. Physical Characteristics The Feature of Board
FIM3030-LV/FIM3040-LV
FIM30xx
FIM3030-HV/FIM3040-HV
FIM30xx
The feature of Optical fingerprint sensor
FIM30xx
FIM30xx
6.2. External Port
External Interface Connection (JP1) Pin 1 2 3 4 5 6 7 8 9 Pin Name VCC RXD TXD SUCCESS FAIL Enroll_Key Delete_Key Identify_Key GND
Description 3.3 V (FIM30xx-LV) / 5 V (FIM30xx-HV) RS-232 Rx receiving signal from host RS-232 Tx transmitting signal to host Output for indicating authentication success Output for indicating authentication fail Input to enroll fingerprint without RS-232 communication Input to delete user without RS-232 communication Input to identify user without RS-232 communication Ground
I/O Port Operation Condition (included in JP1) Pin 4 5 6 7 8 Name EXT_PASS EXT_FAIL EXT_ENROLL EXT_DELETE EXT_IDENTIFY Direction Out Out In In In Initial State Low Low High High High Active State High (500 ms) High (500 ms) Low (more 30ms) Low (more 30ms) Low (more 30ms)
20-Pin Sensor Connection (JP2) Pin 1 2 3 4 5 6 7 8 9 10 Name GND VCLK VCC States POWER IN POWER Description Sensor Ground Sensor Clock Sensor VCC (3.3V) Reserved Reserved Vertical Sync. Horizontal Sync. Sensor Data 0 Sensor Data 1 Sensor Data 2
IN IN IN IN IN
FIM30xx
11 12 13 14 15 16 17 18 19 20 SDATA3 SDATA4 SDATA5 SDATA6 SDATA7 SDA SCL SLED PIXCLK GND IN IN IN IN IN IN/OUT OUT OUT IN POWER Sensor Data 3 Sensor Data 4 Sensor Data 5 Sensor Data 6 Sensor Data 7 I2C Data I2C Clock Sensor LED Pixel Clock Sensor Ground
JTAG (JP3) Pin 1 2 3 4 5 6 7 8 9 Pin Name VCC N/A nSRST TDO TDI nTRST TCK TMS GND Description 3.3 Volt Power N/A JTAG control pin JTAG control pin JTAG control pin JTAG control pin JTAG control pin JTAG control pin Ground
FIM30xx
6.3. Connector and Cable
6.3.1 Sensor
Material List NO
1
VENDOR MOLEX
FIM30xx
6.3.2
Communication
Material List NO
1 2
FIM30xx
6.4. Electrical Characteristics
Parameter Power Supply current Supply Voltage (FIM30xx-LV) Supply Voltage (FIM30xx-HV) RS-232 Output Voltage Swing Input Voltage Range Maximum data rate MIN. TPY. 210 3.3 5 5.4
MAX.
UINTS mA V V V V BPS
3.6 5.5
+15 115,200
FIM30xx
7. Ordering Information
FIM3030 (with OPP03) Ordering Guide
Ordering Number FIM3030-LV FIM3030-HV FIM3040-LV FIM3040-HV Supply Voltage 3.3V 5V 3.3V 5V
FIM30xx
APPENDIX
CPU
Output
VCC
4.7K
CPU
FIM30xx
Boot up time
System Boot-up time means the total time consumed by FIM30xx after system power is supplied. System Boot-up time can be measured as the following.
Power
Identify Enable
tpi
FIM30xx
Support Information