Professional Documents
Culture Documents
1784 In045 - en P
1784 In045 - en P
4 USB-to-Data Highway Plus Cable At the end of its life, this equipment should be collected separately from any unsorted municipal waste.
IMPORTANT
The cable will not connect to Classic PLC-5 processors, such as PLC-5/10, PLC-5/12, PLC-5/15, and PLC-5/25, without an adapter. An adapter can be purchased separately from third-party companies. To comply with the CE Low Voltage Directive (LVD), this equipment must be powered from a source compliant with safety extra low voltage (SELV) or protected extra low voltage (PELV).
The 1784-U2DHP cable replaces both the 1784-PCMK communication card and 1784-PCM6 cable (for computers without PCMCIA slots).
8-pin DIN Cable 2.44 m (8 ft)
Status Indicators
USB-to-Data Highway Plus Cable 5 The cable operates at DH+ communication rates of 57.6 Kbps, 115.2 Kbps, and 230.4 Kbps.
IMPORTANT
The DH+ communication rate is read only when power is applied. To change the communication rate, you must disconnect the cable from the USB port, use the Communication Rate switch to change the communication rate setting, then reconnect the cable to the USB port.
If RSLinx Classic software, version 2.53 or later, is installed on the computer, the device driver is already installed on the computer. Skip this section.
1. Visit http://www.rockwellautomation.com/support/pccards. 2. Click the 1784_u2dhp.inf file. 3. Save the file to a directory on the computer on which you want to install the cable.
If you do not see the Found New Hardware wizard, proceed to step 9. Otherwise, continue with the next step. 2. Select No, not this time and click Next. 3. Select Install from a list or specific location and click Next. 4. Select Search for the best driver. 5. Check only the Include this location checkbox. 6. Browse to the location where you saved the 1784_u2dhp.inf file and click OK. 7. Click Next. 8. Click Finish. TIP If you see a Microsoft Windows error message that displays code 10, disconnect the cable from the USB port, then reconnect the cable to the USB port, so that the Windows operating system recognizes the device.
USB-to-Data Highway Plus Cable 7 9. Insert the other end of the cable having the 8-pin mini DIN connector to a device on your Data Highway Plus network.
8-pin DIN Connector
USB Connector
ATTENTION: The USB cable is not to exceed 3.0 m (9.84 ft). 10. Verify which computer COM port the cable is using. TIP The operating system of the computer you are using assigns a COM port to the cable.
a. Right-click My Computer and choose Manage. b. Select Device Manager. c. Click the + to the left of Ports. d. Make note of the port (for example, COM3) for the 1784-U2DHP cable.
6. Click OK.
10 USB-to-Data Highway Plus Cable The Configure 1784-U2DHP dialog box appears.
6. Click OK.
IMPORTANT
Do not disconnect the cable without first using RSLinx Classic software to stop the driver. Disconnecting the cable without stopping the driver can shut down or cause RSLinx Classic software to become unresponsive.
Product Dimensions
The following illustration shows the product dimensions.
8-pin DIN Cable Length 2.44 m (8 ft) Enclosure Length: 7.62 cm (3 in.) Width: 5.08 cm (2 in.) Thickness: 2.54 cm (1 in.)
Status Indicators
The following table describes the cable status indicators.
Power USB
DH+ Network
Power
Specifications
Technical Specifications - 1784-U2DHP
Attribute Enclosure type rating Power dissipation, max Supply voltage Supply current Power consumption, max Isolation voltage Wiring category
(1)
Value Meets IP30 1.575 W max 5.00V DC 5.25V DC, max 125 mA 1.575 W 30V (continuous), Basic Insulation Type DH+ to USB, Type tested at 500V AC for 60 s 2 - on communication ports(1)
Use this Conductor Category information for planning conductor routing. Refer to Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.
-1085 C (14185 F)
595% noncondensing
Group 1, Class A 8 kV air discharges 10V/m with 1 kHz sine-wave 80% AM from 802000 MHz 10V/m with 200 Hz 50% Pulse 100% AM at 900 MHz 10V/m with 200 Hz 50% Pulse 100% AM at 1890 MHz 10V/m with 1 kHz sine-wave 80% AM from 2000 2700 MHz
Certifications - 1784-U2DHP
Certification(1) c-UL-us CE Value UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E65584. European Union 2004/108/EC EMC Directive, compliant with: EN 61326; Meas./Control/Lab., Industrial Requirements EN 61000-6-2; Industrial Immunity EN 61000-6-4; Industrial Emissions EN 61131-2; Programmable Controllers (Clause 8, Zone A & B) AS/NZS CISPR 11; Industrial Emissions
C-Tick
(1)
When marked. See the Product Certification link at http://www.ab.com for Declarations of Conformity, Certificates, and other certification details.
Additional Resources
These documents contain additional information concerning related Rockwell Automation products.
Resource Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1 Product Certifications website, http://www.ab.com Description Provides general guidelines for installing a Rockwell Automation industrial system. Provides declarations of conformity, certificates, and other certification details.
Notes:
Installation Assistance
If you experience a problem within the first 24 hours of installation, please review the information that's contained in this manual. You can also contact a special Customer Support number for initial help in getting your product up and running. United States or Canada Outside United States or Canada 1.440.646.3434 Use the Worldwide Locator at http://www.rockwellautomation.com/support/americas/phone_en.html, or contact your local Rockwell Automation representative.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete this form, publication RA-DU002, available at http://www.rockwellautomation.com/literature,
Allen-Bradley, Rockwell Software, Rockwell Automation, Data Highway Plus, RSLinx Classic, PLC-5, SLC, and TechConnect are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.., Kar Plaza Merkezi E Blok Kat:6 34752 erenky, stanbul, Tel: +90 (216) 5698400
PN-76634
Copyright 2010 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.