Professional Documents
Culture Documents
7529v1 1 (G52-75291X2)
7529v1 1 (G52-75291X2)
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the measures listed below.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Notice 1
The changes or modifications not expressly approved by the party responsible for
compliance could void the users authority to operate the equipment.
Notice 2
Shielded interface cables and A.C. power cord, if any, must be used in order to comply with
the emission limits.
VOIR LA NOTICE DNSTALLATION AVANT DE RACCORDER AU RESEAU.
Micro-Star International
MS-7529
G52-75291X2
Copyright Notice
The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL.
We take every care in the preparation of this document, but no guarantee is given as to the
correctness of its contents. Our products are under continual improvement and we reserve
the right to make changes without notice.
Trademarks
All trademarks are the properties of their respective owners.
AMD Corporation.
NVIDIA , the NVIDIA logo, DualNet, and nForce are registered trademarks or trademarks of
Revision History
Revision
Revision History
Date
V1.1
First release
August. 2008
Safety Instructions
The openings on the enclosure are for air convection hence protects the equipment
from overheating. Do not cover the openings.
Make sure the voltage of the power source and adjust properly 110/220V before
connecting the equipment to the power inlet.
Place the power cord such a way that people can not step on it. Do not place
anything over the power cord.
Always Unplug the Power Cord before inserting any add-on card or module.
Never pour any liquid into the opening that could damage or cause electrical shock.
If any of the following situations arises, get the equipment checked by a service
personnel:
- The power cord or plug is damaged.
- Liquid has penetrated into the equipment.
- The equipment has been exposed to moisture.
- The equipment does not work well or you can not get it work according to User
Manual.
- The equipment has dropped and damaged.
- The equipment has obvious sign of breakage.
WEEE Statement
ENGLISH
To protect the global environment and as an environmentalist, MSI must remind you
that...
Under the European Union ("EU") Directive on Waste Electrical and Electronic Equipment, Directive
2002/96/EC, which takes effect on August 13, 2005, products of "electrical and electronic equipment"
cannot be discarded as municipal waste anymore and manufacturers of covered electronic equipment
will be obligated to take back such products at the end of their useful life. MSI will comply with the product
take back requirements at the end of life of MSI-branded products that are sold into the EU. You can
return these products to local collection points.
DEUTSCH
Hinweis von MSI zur Erhaltung und Schutz unserer Umwelt
Gem der Richtlinie 2002/96/EG ber Elektro- und Elektronik-Altgerte drfen Elektro- und
Elektronik-Altgerte nicht mehr als kommunale Abflle entsorgt werden. MSI hat europaweit
verschiedene Sammel- und Recyclingunternehmen beauftragt, die in die Europische Union in Verkehr
gebrachten Produkte, am Ende seines Lebenszyklus zurckzunehmen. Bitte entsorgen Sie dieses
Produkt zum gegebenen Zeitpunkt ausschliesslich an einer lokalen Altgertesammelstelle in Ihrer Nhe.
FRANAIS
En tant qucologiste et afin de protger lenvironnement, MSI tient rappeler ceci...
Au sujet de la directive europenne (EU) relative aux dchets des quipement lectriques et
lectroniques, directive 2002/96/EC, prenant effet le 13 aot 2005, que les produits lectriques et
lectroniques ne peuvent tre dposs dans les dcharges ou tout simplement mis la poubelle. Les
fabricants de ces quipements seront obligs de rcuprer certains produits en fin de vie. MSI prendra
en compte cette exigence relative au retour des produits en fin de vie au sein de la communaut
europenne. Par consquent vous pouvez retourner localement ces matriels dans les points de
collecte.
MSI ,
, ....
()
(
WEEE 2002/96/EC), 13 2005 , ,
, ,
. MSI
, MSI EC,
. .
ESPAOL
MSI como empresa comprometida con la proteccin del medio ambiente, recomienda:
Bajo la directiva 2002/96/EC de la Unin Europea en materia de desechos y/o equipos electrnicos, con
fecha de rigor desde el 13 de agosto de 2005, los productos clasificados como "elctricos y equipos
electrnicos" no pueden ser depositados en los contenedores habituales de su municipio, los fabricantes
de equipos electrnicos, estn obligados a hacerse cargo de dichos productos al termino de su perodo
de vida. MSI estar comprometido con los trminos de recogida de sus productos vendidos en la Unin
Europea al final de su periodo de vida. Usted debe depositar estos productos en el punto limpio
establecido por el ayuntamiento de su localidad o entregar a una empresa autorizada para la recogida de
estos residuos.
NEDERLANDS
Om het milieu te beschermen, wil MSI u eraan herinneren dat.
De richtlijn van de Europese Unie (EU) met betrekking tot Vervuiling van Electrische en Electronische
producten (2002/96/EC), die op 13 Augustus 2005 in zal gaan kunnen niet meer beschouwd worden als
vervuiling.
Fabrikanten van dit soort producten worden verplicht om producten retour te nemen aan het eind van
hun levenscyclus. MSI zal overeenkomstig de richtlijn handelen voor de producten die de merknaam MSI
dragen en verkocht zijn in de EU. Deze goederen kunnen geretourneerd worden op lokale
inzamelingspunten.
SRPSKI
Da bi zatitili prirodnu sredinu, i kao preduzee koje vodi rauna o okolini i prirodnoj sredini, MSI mora da
vas podesti da
Po Direktivi Evropske unije ("EU") o odbaenoj ekektronskoj i elektrinoj opremi, Direktiva 2002/96/EC,
koja stupa na snagu od 13. Avgusta 2005, proizvodi koji spadaju pod "elektronsku i elektrinu opremu" ne
mogu vie biti odbaeni kao obian otpad i proizvoai ove opreme bie prinueni da uzmu natrag ove
proizvode na kraju njihovog uobiajenog veka trajanja. MSI e potovati zahtev o preuzimanju ovakvih
proizvoda kojima je istekao vek trajanja, koji imaju MSI oznaku i koji su prodati u EU. Ove proizvode
moete vratiti na lokalnim mestima za prikupljanje.
POLSKI
Aby chroni nasze rodowisko naturalne oraz jako firma dbajca o ekologi, MSI przypomina, e...
Zgodnie z Dyrektyw Unii Europejskiej ("UE") dotyczc odpadw produktw elektrycznych i
elektronicznych (Dyrektywa 2002/96/EC), ktra wchodzi w ycie 13 sierpnia 2005, tzw. produkty oraz
wyposaenie elektryczne i elektroniczne " nie mog by traktowane jako mieci komunalne, tak wic
producenci tych produktw bd zobowizani do odbierania ich w momencie gdy produkt jest
wycofywany z uycia. MSI wypeni wymagania UE, przyjmujc produkty (sprzedawane na terenie Unii
Europejskiej) wycofywane z uycia. Produkty MSI bdzie mona zwraca w wyznaczonych punktach
zbiorczych.
TRKE
evreci zelliiyle bilinen MSI dnyada evreyi korumak iin hatrlatr:
Avrupa Birlii (AB) Kararnamesi Elektrik ve Elektronik Malzeme At, 2002/96/EC Kararnamesi altnda
13 Austos 2005 tarihinden itibaren geerli olmak zere, elektrikli ve elektronik malzemeler dier atklar
gibi pe atlamayacak ve bu elektonik cihazlarn reticileri, cihazlarn kullanm sreleri bittikten sonra
rnleri geri toplamakla ykml olacaktr. Avrupa Birliine satlan MSI markal rnlerin kullanm
sreleri bittiinde MSI rnlerin geri alnmas istei ile ibirlii ierisinde olacaktr. rnlerinizi yerel
toplama noktalarna brakabilirsiniz.
ESKY
Zle nm na ochran ivotnho prosted - spolenost MSI upozoruje...
Podle smrnice Evropsk unie ("EU") o likvidaci elektrickch a elektronickch vrobk 2002/96/EC platn
od 13. srpna 2005 je zakzno likvidovat "elektrick a elektronick vrobky" v bnm komunlnm
odpadu a vrobci elektronickch vrobk, na kter se tato smrnice vztahuje, budou povinni odebrat
takov vrobky zpt po skonen jejich ivotnosti. Spolenost MSI spln poadavky na odebrn
vrobk znaky MSI, prodvanch v zemch EU, po skonen jejich ivotnosti. Tyto vrobky mete
odevzdat v mstnch sbrnch.
MAGYAR
Annak rdekben, hogy krnyezetnket megvdjk, illetve krnyezetvdknt fellpve az MSI
emlkezteti nt, hogy ...
Az Eurpai Uni (EU") 2005. augusztus 13-n hatlyba lp, az elektromos s elektronikus
berendezsek hulladkairl szl 2002/96/EK irnyelve szerint az elektromos s elektronikus
berendezsek tbb nem kezelhetek lakossgi hulladkknt, s az ilyen elektronikus berendezsek
gyrti kteless vlnak az ilyen termkek visszavtelre azok hasznos lettartama vgn. Az MSI
betartja a termkvisszavtellel kapcsolatos kvetelmnyeket az MSI mrkanv alatt az EU-n bell
rtkestett termkek esetben, azok lettartamnak vgn. Az ilyen termkeket a legkzelebbi
gyjthelyre viheti.
ITALIANO
Per proteggere lambiente, MSI, da sempre amica della natura, ti ricorda che.
In base alla Direttiva dellUnione Europea (EU) sullo Smaltimento dei Materiali Elettrici ed Elettronici,
Direttiva 2002/96/EC in vigore dal 13 Agosto 2005, prodotti appartenenti alla categoria dei Materiali
Elettrici ed Elettronici non possono pi essere eliminati come rifiuti municipali: i produttori di detti materiali
saranno obbligati a ritirare ogni prodotto alla fine del suo ciclo di vita. MSI si adeguer a tale Direttiva
ritirando tutti i prodotti marchiati MSI che sono stati venduti allinterno dellUnione Europea alla fine del
loro ciclo di vita. possibile portare i prodotti nel pi vicino punto di raccolta.
Table of Content
English...........................1
............................13
Franais.........................25
Deutsch .........................37
.........................51
........................65
........................77
............................89
INTRODUCTION
Thank you for choosing the G31M3 V2 Series (MS-7529 v1.x) Micro-ATX mainboard. The
G31M3 V2 Series are based on Intel G31 & Intel ICH7 chipsets for optimal system
TM
TM
efficiency. Designed to fit the advanced Intel Core 2 Duo/ Core 2 Quad/ Pentium
Dual-Core E2XXX and Celeron 4XXX/ Wolfdale Series LGA 775 processor, the G31M3 V2
Series deliver a high performance and professional desktop platform solution.
Layout
SPECIFICATIONS
Processor Support
TM
TM
l Supports Intel Core 2 Duo/ Core 2 Quad/ Pentium Dual-Core E2XXX and Celeron
4XXX/ Wolfdale Series processor in LGA 775 package
l We recommend using the following CPUs:
1. E8190 ~ E8600
2. E7200 ~ E7300
3. E6300 ~ E6850
4. E4300 ~ E4700
5. E2100 ~ E2200
6. E1200 ~ E1600
7. 420 ~ 460
Please refer to CPU Support for compatible CPU; the above description is for reference
only.
l Supports 4 pin CPU fan pin-header with Fan speed Control
l Supports TDP Max. 95W
(For the latest information about CPU, please visit:
http://global.msi.com.tw/index.php?func=cpuform)
Supported FSB
l 800/ 1066/ 1333 MHz
Chipset
Memory Support
l DDR2 667/ 800 SDRAM (4GB Max)
l 2 DDR2 DIMMs (240 pin/ 1.8V)
(For more information on compatible components, please visit:
http://global.msi.com.tw/index.php?func=testreport)
LAN(Optional)
l
l
l
l
Audio
IDE
l 1 IDE port by ICH7
l Supports Ultra DMA 66/100 mode
l Supports PIO, Bus Master operation mode
SATA
l 2 SATA II ports by ICH7
l Supports 4 SATA II devices
l Supports storage and data transfers at up to 3Gb/s
Floppy
l 1 floppy port
l Supports 1 FDD with 360KB, 720KB, 1.2MB, 1.44MB and 2.88 MB
TPM (Optional)
l Supports TPM
Connectors
l Back panel
- 1 PS/2 mouse port
- 1 PS/2 keyboard port
- 1 serial port (COM1)
- 1 VGA port
- 1 parallel port supporting SPP/EPP/ECP mode
- 4 USB 2.0 Ports
- 1 RJ-45 LAN jack
- 3/6 flexible audio jacks(optional)
l On-Board Pinheaders / Connectors
- 2 USB 2.0 pinheaders
- 1 CD-In connector
- 1 S/PDIF-Out pinheader
- 1 Front Panel Audio pinheader
- 1 serial port connector
- 1 TPM connector (optional)
- 1 chassis intrusion switch pinheader
- 1 SPI Debugging connector
Slots
l 1 PCI Express x16 slot
l 2 PCI slots
l Support 3.3V / 5V PCI bus Interface
Form Factor
l Micro-ATX (24.4 cm X 19.3 cm)
Mounting
l 6 mounting holes
Important:
To reach the 8-channel sound effect, the 7th and 8th channels must be outputted from front
panel (pinheader) if you purchase the mainboard with 3 audio jacks.
REAR PANEL
The rear panel provides the following connectors:
HARDWARE SETUP
This chapter tells you how to install the CPU, memory modules, and expansion cards, as
well as how to setup the jumpers on the mainboard. It also provides the instructions on
connecting the peripheral devices, such as the mouse, keyboard, etc. While doing the
installation, be careful in holding the components and follow the installation procedures.
1.
2.
3.
4.
5.
6.
on the edge of the CPU base. Note that the alignment keys
are matched.
7.
8.
9.
Press down the load lever lightly onto the load plate, and
then secure the lever with the hook under retention tab.
10. Align the holes on the mainboard with the cooler. Push down
the cooler until its four clips get wedged into the holes of the
mainboard.
11. Press the four hooks down to fasten the cooler. Then rotate
the locking switch (refer to the correct direction marked on it)
to lock the hooks.
12. Turn over the mainboard to confirm that the clip-ends are
correctly inserted.
Important:
Read the CPU status in BIOS.
Whenever CPU is not installed, always protect your CPU socket pin with the plastic cap
covered to avoid damaging.
Mainboard photos shown in this section are for demonstration of the CPU/cooler installation
only. The appearance of your mainboard may vary depending on the model you purchase.
The memory module has only one notch on the center and will only fit in the right
orientation.
2.
Insert the memory module vertically into the DIMM slot. Then push it in until the
golden finger on the memory module is deeply inserted in the DIMM slot. You can
barely see the golden finger if the memory module is properly inserted in the DIMM
slot. The plastic clip at each side of the DIMM slot will automatically close when the
memory module is properly seated.
3.
Manually check if the memory module has been locked in place by the DIMM slot
clips at the sides.
Notch
Volt
Important:
DDR2 memory modules are not interchangeable with DDR and the DDR2 standard is not
backwards compatible. You should always install DDR2 memory modules in the DDR2
DIMM slots.
To enable successful system boot-up, always insert the memory modules into the DIMM1
first.
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
Res
GND
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
+12V
GND
Important:
Make sure that all the connectors are connected to proper ATX power supplies to ensure
stable operation of the mainboard.
Power supply of 350 watts (and above) is highly recommended for system stability.
ATX 12V power connection should be greater than 18A.
Important:
Please do not fold the Serial ATA cable into 90-degree angle. Otherwise,
data loss may occur during transmission.
Control
Sensor
+12V
GND
The fan power connectors support system cooling fan with +12V.
When connecting the wire to the connectors, always note that the
red wire is the positive and should be connected to the +12V; the
black wire is Ground and should be connected to GND. If the
mainboard has a System Hardware Monitor chipset on-board, you
must use a specially designed fan with speed sensor to take
advantage of the CPU fan control.
GND
+12V
Sensor
Sensor
GND
+12V
2
1
GND
CINTRU
GND
SPDIF
VCC
8 7
JFP2
Speaker
Power
LED
2 1
+
-
HDD
LED
Reset
Switch
- -
JFP1
1 2
GND
Power
LED
Power
Switch
9 10
USB1+
USB1-
GND
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VC C
U SB0- GND
USB0+
MIC2_JD
VCC5
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
DSR
DTR CTS
Key,no pin (10)
RI (9)
(2) SIN
(1) DCD
SOUT RTS
GND
12
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
1
2
3
1
2
3
Keep Data
1
2
3
Clear Data
Important:
You can clear CMOS by shorting 2-3 pin while the system is off. Then return to 1-2 pin
position. Avoid clearing the CMOS while the system is on; it will damage the mainboard.
The PCI slot supports LAN card, SCSI card, USB card, and other add-on cards that
comply with PCI specifications.
Important:
When adding or removing expansion cards, make sure that you unplug the power supply
first. Meanwhile, read the documentation for the expansion card to configure any
necessary hardware or software settings for the expansion card, such as jumpers,
switches or BIOS configuration.
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
BIOS Setup
Power on the computer and the system will start POST (Power On Self Test) process. When
the message below appears on the screen, press <DEL> key to enter Setup.
Press DEL to enter SETUP
If the message disappears before you respond and you still wish to enter Setup, restart the
system by turning it OFF and On or pressing the RESET button. You may also restart the
system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.
Main Page
Cell Menu
10
The Enhanced Intel SpeedStep technology allows you to set the performance level of the
microprocessor whether the computer is running on battery or AC power. If you intent to
adjust the CPU Ratio, please set Disabled in this field. This field will appear after you
installed the CPU which support speedstep technology.
Adjust CPU FSB Frequency (MHz)
When Auto Detect CPU Frequency item set to [Disable], this item will allow you to manually
adjust the CPU FSB frequency.
Adjusted CPU Frequency
It shows the adjusted CPU frequency (FSB x Ratio). Read-only.
Advance DRAM Configuration > DRAM CAS# Latency
The field controls the CAS latency, which determines the timing delay before DRAM starts a
read command after receiving it. [2T] increases system performance while [2.5T] provides
more stable system performance. Setting to [By SPD] enables DRAM CAS# Latency
automatically to be determined by BIOS based on the configurations on the SPD (Serial
Presence Detect) EEPROM on the DRAM module.
FSB/Memory Ratio
When Auto Detect DRAM Frequency item set to [Disable], this item will allow you to
manually adjust the FSB/Ratio of the memory.
Adjusted DDR Memory Frequency
It shows the adjusted DDR Memory frequency. Read-only.
Adjust PCI-E Frequency (MHz)
This item allows you to select the PCI Express clock frequency (in MHz) and overclock by
adjusting the PCI Express clock to a higher frequency.
Auto Disable DIMM/PCI Frequency
When set to [Enabled], the system will remove (turn off) clocks from empty DIMM and PCI
slots to minimize the electromagnetic interference (EMI).
Spread Spectrum
When the motherboards clock generator pulses, the extreme values (spikes) of the pulses
create EMI (Electromagnetic Interference). The Spread Spectrum function reduces the EMI
generated by modulating the pulses so that the spikes of the pulses are reduced to flatter
curves. If you do not have any EMI problem, leave the setting at Disabled for optimal system
stability and performance. But if you are plagued by EMI, set to Enabled for EMI reduction.
Remember to disable Spread Spectrum if you are overclocking because even a slight jitter
can introduce a temporary boost in clock speed which may just cause your overclocked
processor to lock up.
Important:
If you do not have any EMI problem, leave the setting at [Disabled] for optimal system
stability and performance. But if you are plagued by EMI, select the value of Spread
Spectrum for EMI reduction.
11
The greater the Spread Spectrum value is, the greater the EMI is reduced, and the system
will become less stable. For the most suitable Spread Spectrum value, please consult your
local EMI regulation.
Remember to disable Spread Spectrum if you are overclocking because even a slight jitter
can introduce a temporary boost in clock speed which may just cause your overclocked
processor to lock up.
12
G31M3 V2 (MS-7529 v1.X) Micro-ATX . G31M3
TM
TM
. Intel Core 2 Duo/ Core 2 Quad/ Pentium Dual-Core E2XXX
Celeron 4XXX/ Wolfdale LGA 775 G31M3 V2
.
13
TM
TM
z LGA 775 Intel Core 2 Duo/ Core 2 Quad/ Pentium Dual-Core E2XXX
Celeron 4XXX/ Wolfdale
z CPU :
1. E8190 ~ E8600
2. E7200 ~ E7300
3. E6300 ~ E6850
4. E4300 ~ E4700
5. E2100 ~ E2200
6. E1200 ~ E1600
7. 420 ~ 460
CPU CPU ;
.
z 4 CPU
z TDP Max. 95W
(CPU http://global.msi.com.tw/index.php?func=cpuform )
FSB
z 800/ 1066/ 1333 MHz
z : Intel G31
z : Intel ICH7
z -DDR2 667/800 SDRAM( 4GB)
z 2 DDR2 DIMMs(240 /1.8V)
( http://global.msi.com.tw/index.php?func=testreport
)
LAN()
z
z
z
z
z Realtek ALC888
z 8
z Vista Premium
IDE
z ICH7 IDE 1
z Ultra DMA 66/100
14
z PIO,
SATA
z ICH7 SATA II 2
z 4 SATA II
z 3Gb/s
z 1
z 1 FDD with 360KB, 720KB, 1.2MB, 1.44MB 2.88 MB
TPM()
z TPM
z
- PS/2 1
- PS/2 1
- (COM1) 1
- -VGA 1
- SPP/EPP/ECP 1
- USB 2.0 4
- 1 RJ-45 LAN
- 3/6 ()
z /
- USB 2.0 2
- CD 1
- S/PDIF 1
- 1
- l
- TPM 1 ()
- 1
- SPI 1
z Micro-ATX(24.4 cm X 19.3 cm)
z 6
:
8 , 3 7 8
() .
15
VGA
USB
USB
CPU, ,
. , .
, .
LGA775 CPU
CPU . ,
/ CPU .
CPU . CPU
.
LGA 775 CPU
LGA775CPU
1.
CPU
. CPU ,
.
2.
3.
4.
5.
6.
CPU , CPU
. CPU
. .
16
7.
CPU .
, CPU
.
8.
9.
,
.
10. . 4
.
11. 4 .
( ).
12. .
:
BIOS CPU .
CPU , CPU
.
CPU/ .
.
1.
, .
2.
DIMM .
DIMM . DIMM
. ,
DIMM .
3.
DIMM
.
Notch
Volt
:
DDR2 DDR , DDR2 .
DDR2 DIMM DDR2 .
, DIMM .
17
ATX 24 : ATX1
ATX 24
. ATX 24 ,
,
.
.
20 ATX . 20
ATX , 1
13 ( ).
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
GND
Res
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
12V CPU .
+12V
GND
:
ATX
.
350 .
ATX 12V 18A ..
: FDD1
360 KB, 720 KB, 1.2 MB, 1.44 MB 2.88 MB
.
IDE : IDE1
IDE , IDE
.
:
2 IDE ,
, /
. IDE
.
:
ATA 90 . ,
.
18
: CPUFAN1, SYSFAN1,
SYSFAN2
Control
Sensor
+12V
GND
+12V .
, +12V
, GND
.
, CPU
.
GND
+12V
Sensor
Sensor
GND
+12V
: JCI1
.
, .
. , BIOS
.
2
1
GND
CINTRU
S/PDIF : JSPD1
GND
SPDIF
VCC
CD : CD_IN1
.
GND
8 7
JFP2
LED
Power
Speaker
LED
2 1
+
-
- -
JFP1
1 2
HDD
LED
Reset
Switch
: JFP1, JFP2
Power
LED
Power
Switch
9 10
USB1+
USB1GND
19
N.C.(10)
(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
: JAUD1
2_JD
VCC5
NC
_JD(10)
(2)GND
_L(9)
(1)_L
_R
_R
SPI : JSPI1
.
: JCOM1
DSR
16550A 16
FIFO .
.
DTR
CTS
(10)
(2) SIN
(1) DCD
RI (9)
SOUT RTS
GND
TPM : JTPM1()
TPM(Trusted Platform Module)
. TPM
.
12
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
CMOS : JBAT1
CMOS RAM .
CMOS RAM , OS
. ,
.
1
2
3
1
2
3
1
2
3
Keep Data
Data
Clear
:
2-3 CMOS . 1-2
. CMOS .
.
20
PCI
Interrupt request line IRQ I-R-Q ,
. PCI IRQ
PCI .
1
PCI 1
INT A#
INT B#
INT C#
INT D#
PCI 2
INT B#
INT C#
INT D#
INT A#
BIOS
POST(Power On Self Test) .
, <DEL> .
DEL (SETUP) .
,
(RESET) . <Ctrl>, <Alt> <Delete>
.
21
Main Page ( )
22
Cell Menu ( )
Intel SpeedStep AC
. CPU
. speedstep CPU
.
Adjust CPU FSB Frequency (CPU FSB ) (MHz)
CPU (Auto Detect CPU Frequency) [ (Disable)]
, CPU FSB .
Adjusted CPU Frequency ( CPU )
CPU (FSB x ). .
Advance DRAM Configuration > DRAM CAS# Latency
( DRAM > DRAM CAS# )
DRAM
CAS . [2.5T] [2T]
. [SPD (By SPD)] DRAM SPD(
) EFPROM BIOS DRAM CAS# (DRAM CAS#
Latency) .
FSB/Memory Ratio (FSB/ )
DRAM (Auto Detect CPU Frequency) [ (Disable)]
, FSB/ .
Adjusted DDR Memory Frequency ( DDR )
DDR . .
23
24
INTRODUCTION
Flicitations, vous venez dacqurir une carte mre des sries Micro-ATX G31M3 V2
(MS-7529 v1.x). Les G31M3 V2 sries sont bases sur les chipsets Intel G31 et Intel
ICH7 offrant un systme trs performant. La carte fonctionne avec le processeur LGA 775
TM
TM
de Intel Core 2 Duo/ Core 2 Quad/ Pentium Dual-Core E2XXX et Celeron 4XXX/
Wolfdale sries, les sries G31M3 V2 sont trs performantes et offrent une solution adapte
tant aux professionnels quaux particuliers.
Schma
25
SPCIFICITS
Processeurs Supports
TM
TM
z Supporte les processeurs de srie Intel Core 2 Duo/ Core 2 Quad/ Pentium
Dual-Core E2XXX et Celeron 4XXX/ Wolfdale dans le paquet LGA 775.
z Nous vous recommandons d'utiliser un CPU comme ci-dessous:
1. E8190 ~ E8600
2. E7200 ~ E7300
3. E6300 ~ E6850
4. E4300 ~ E4700
5. E2100 ~ E2200
6. E1200 ~ E1600
7. 420 ~ 460
Veuillez vous rfrer au support du CPU pour un CPU compatible; la description
au-dessus n'est que pour une rfrence.
z Supporte un connecteur de 4 pins du ventilateur de CPU avec le Contrleur de la vitesse
du ventilateur.
z Supporte TDP Max. 95W
(Pour plus dinformations sur le CPU, veuillez visiter :
http://global.msi.com.tw/index.php?func=cpuform)
FSB support
z 800/ 1066/ 1333 MHz
Chipset
Mmoire Supporte
z DDR2 667/ 800 SDRAM (4GB Max)
z 2 DDR2 DIMMs (240pin/ 1.8V)
(Pour plus dinformations sur les composants compatibles, veuillez visiter :
http://global.msi.com.tw/index.php?func=testreport)
LAN(Optionnel)
z
z
z
z
Audio
IDE
z 1 port IDE par ICH7
z Supporte le mode Ultra DMA 66/100
z Supporte les modes dopration PIO, Bus Master
26
SATA
z 2 ports SATA II par ICH7
z Supporte 4 priphriques SATA II
z Supporte le stockage et un taux de transfert jusqu 3Gb/s
Disquette
z 1 port de disquette
z Supporte 1 FDD avec 360KB, 720KB, 1.2MB, 1.44MB et 2.88 MB.
TPM (Optionnel)
z Supporte TPM
Connecteurs
z Panneau arrire
- 1 port souris PS/2
- 1 port clavier PS/2
- 1 port srie (COM1)
- 1 port VGA
- 1 port parallle supportant le mode SPP/EPP/ECP
- 4 ports USB 2.0
- 1 jack LAN RJ-45
- 3/6 jacks audio flexibles (optionnel)
z Connecteurs intgrs
- 2 connecteurs USB 2.0
- 1 connecteur CD-In
- 1 connecteur S/PDIF-Out
- 1 connecteur audio avant
- 1 connecteur port srie
- 1 connecteur TPM (optionnel)
- 1 connecteur chassis intrusion switch
- 1 connecteur SPI Debugging
Slots
z 1 slot PCI Express x16
z 2 slots PCI
z Supporte linterface bus PCI 3.3V / 5V
Dimension
z Micro-ATX (24.4cm X 19.3 cm)
Montage
z 6 trous de montage
Important:
me
me
27
Panneau Arrire
Le panneau arrire dispose les connecteurs suivants:
INSTALLATION MATRIELLE
Ce chapitre vous indique comment installer le CPU, les modules de mmoire, les cartes
dextension et comment installer les cavaliers sur la carte. Il explique galement comment
connecter priphriques tels que la souris, le clavier etc. Lors de linstallation du matriel,
veuillez suivre les instructions de montage pour viter dendommager quoi que ce soit.
1.
2.
3.
4.
5.
28
6.
7.
8.
9.
Important:
Lisez les status du CPU dans le BIOS.
Toujours protgez les pins de socket du CPU avec le platique de tout domage quand le
CPU nest pas install.
Les photos de carte sont montres ici pour une dmonstration de linstallation du ventilateur
des CPU de Socket AM2 seulement. Lapparence de votre carte peut changer selon le
model que vous achetez.
2.
3.
Notch
Volt
29
Important:
Les modules de mmoire DDR2 ne sont pas interchangeables par DDR et vice versa. Vous
devez installer toujours les modules de mmoire DDR2 dans les slots DDR2 DIMM.
Pour lancer avec succs votre ordinateur, insrez tout dabord les modules de mmoire
dans le DIMM1.
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
GND
Res
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
+12V
GND
30
Important:
Veuillez ne pas tordre le cble Srie ATA 90 degrs. Cela pourrait
lendommager et entraner la perte de donnes lors des phases de
transfert de celles-ci.
Control
Sensor
+12V
GND
Connecteurs dalimentation du
ventilateur: CPUFAN1, SYSFAN1,
SYSFAN2
Les connecteurs dalimentation du systme de refroidissement
supportent un systme de refroidissement de +12V. Lors de la
connexion du cble, assurez-vous que le fil rouge soit connect au
+12V et le fil noir connect au GND. Si la carte mre possde un
systme de gestion intgr, vous devez utiliser un ventilateur ayant
ces caractristiques si vous voulez contrler le ventilateur du CPU.
GND
+12V
Sensor
Sensor
GND
+12V
2
1
GND
CINTRU
GND
SPDIF
VCC
8 7
JFP2
Speaker
Power
LED
2 1
HDD
LED
Reset
Switch
JFP1
1 2
- -
9 10
31
GND
Power
LED
Power
Switch
USB1+
USB1-
N.C.(10)
Key,no pin(9)
USB0- GND
USB0+
GND
(2)VCC
(1)VCC
MIC2_JD
VCC5
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
(2) SIN
(1) DCD
SOUT RTS
GND
12
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
1
2
3
1
2
3
Keep Data
1
2
3
Clear Data
Important:
Vous pouvez effacer le CMOS en positionnant le cavalier sur les broches 2-3 lorsque le
PC nest pas allum. Puis il faut remettre le cavalier en position 1-2. Ne surtout pas
effacer le CMOS lorsque le PC est allum, cela endommagera la carte mre.
32
Le slot PCI support la carte LAN, la carte SCSI, la carte USB, et dautres cartes ajoutes
qui sont compatibles avec les spcifications de PCI.
Important:
Quand vous ajoutez ou enlevez les cartes dexpansion, assurez-vous de dbrocher
dabords lalimentation. En mme temps, lisez les documentations afin de configurer tous
les matriel et logiciel ncessaires pour la carte dexpansion, tel que les cavaliers,
switches ou la configurations du BIOS.
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
BIOS Setup
Lorsque le PC dmarre, le processus de POST (Power On Self Test) se met en route.
Quand le message ci-dessous apparat lcran, appuyer sur <DEL> pour accder au
Setup.
Appuyer sur DEL pour accder au SETUP
Si le message disparat avant que nayez appuy sur la touche, redmarrez le PC avec
laide du bouton RESET. Vous pouvez aussi redmarrer en utilisant la combinaison des
touches <Ctrl>, <Alt>, et <Delete>.
33
Page Principale
34
Cell Menu
35
36
EINLEITUNG
Danke, dass Sie das G31M3 V2 Series (MS-7529 v1.x) Micro-ATX Mainboard gewhlt
haben. Das G31M3 V2 Series Series basiert auf dem Intel G31 & Intel ICH7 Chipsatz und
ermglicht so ein optimales und effizientes System. Entworfen, um den hochentwickelten
TM
TM
Intel Core 2 Duo/ Core 2 Quad/ Pentium Dual-Core E2XXX und Celeron 4XXX/
Wolfdale Series LGA 775 Prozessoren, stellt das G31M3 V2 Series die ideale Lsung zum
Aufbau eines professionellen Hochleistungsdesktopsystems dar.
Layout
37
SPEZIFIKATIONEN
Prozessoren
TM
z Untersttzt Intel Core 2 Duo/ Pentium Dual-Core E2XXX und Celeron 4XXX/ Wolfdale
Series Prozessoren fr Sockel LGA 775.
z Wir empfehlen Ihnen, die folgenden CPUs zu verwenden:
1. E8190 ~ E8600
2. E7200 ~ E7300
3. E6300 ~ E6850
4. E4300 ~ E4700
5. E2100 ~ E2200
6. E1200 ~ E1600
7. 420 ~ 460
Bitte hinweisen Sie auf die CPU-Untersttzung fr kompatible CPU; die obenstehende
Beschreibung ist nur eine Referenz.
z Untersttzt CPU Lftersteuerung ber eine 4-polige Stiftleiste
z Untersttzt TDP max. 95W
(Weitere CPU Informationen finden Sie unter:
http://global.msi.com.tw/index.php?func=cpuform)
FSB(Front-Side-Bus)
z 800/ 1066/ 1333 MHz
Chipsatz
Speicher
z DDR2 667/ 800 SDRAM (max. 4GB)
z 2 DDR2 DIMMs (240Pin/ 1.8V)
(Weitere Informationen zu kompatiblen Speichermodulen finden Sie unter:
http://global.msi.com.tw/index.php?func=testreport)
LAN(Optional)
z
z
z
z
Audio
IDE
z 1 IDE Port ber ICH7
z Untersttzt die Betriebmodi Ultra DMA 66/100 mode
z Untersttzt die Betriebmodi PIO, Bus Mastering
38
SATA
z 2 SATA II Ports ber ICH7
z Untersttzt 4 SATA II Gerte
z Untersttzt Datenbertragungsraten von bis zu 3Gb/s
Diskette
z 1 Disketten Anschluss
z Untersttzt 1 Diskettenlaufwerk mit 360 KB, 720 KB, 1.2 MB, 1.44 MB und 2.88 MB.
TPM (Optional)
z Untersttzt TPM
Anschlsse
z Hintere Ein-/ und Ausgnge
- 1 PS/2 Mausanschluss
- 1 PS/2 Tastaturanschluss
- 1 Serielle Schnittstelle (COM1)
- 1 VGA Anschluss
- 1 Parallele Schnittstelle untersttzt die Betriebsmodi SPP/EPP/ECP
- 4 USB 2.0 Anschlsse
- 1 RJ-45 LAN Buchse
- 3/6 Audiobuchsen (optional)
z On-Board Stiftleiste/ Anschlsse
- 2 USB 2.0 Stiftleisten
- 1 CD Stiftleiste fr Audio Eingang
- 1 S/PDIF-Ausgang Stiftleiste
- 1 Audio Stiftleiste fr Gehuse Audio Ein-/ Ausgnge
- 1 Serielle Stiftleiste
- 1 TPM Stiftleiste (optional)
- 1 Gehusekontaktschalter
- 1 SPI Behegung Anschluss
Schnittstellen
z 1 PCI Express x16 Schnittstelle
z 2 PCI Schnittstelle
z Untersttzt 3.3V/ 5V PCI Bus Interface
Form Faktor
z Micro-ATX (24.4cm X 19.3 cm)
Mountage
z 6 Montagebohrungen
Wichtig:
Fr der 8-Kanal Geruscheffekt, wenn Sie das mainboard mit 3 Audiobuchsen kaufen,
mssen die 7. und 8. Kanal von der Frontpanel (Stiftleiste) abgefragt.
39
Hinteres Anschlusspanel
Das hintere Anschlusspanel verfgt ber folgende Anschlsse:
HARDWARE SETUP
Dieses Kapitel informiert Sie darber, wie Sie die CPU, CPU Khler und Speichermodule,
Erweiterungskarten einbauen, des weiteren darber,wie die Steckbrcken auf dem
Mainboard gesetzt werden. Zudem bietet es Hinweise darauf, wie Sie Peripheriegerte
anschlieen, wie z.B. Maus, Tastatur, usw. Handhaben Sie die Komponenten whrend des
Einbaus vorsichtig und halten Sie sich an die vorgegebene Vorgehensweise beim Einbau.
1.
2.
3.
4.
40
5.
Klappen Sie den Hebel ganz auf und ffnen Sie die
Metallverschlussklappe.
6.
7.
8.
9.
Wichtig:
Prfen Sie die Status der CPU im BIOS.
Wenn keine CPU installiert ist, schtzen Sie immer den CPU-Sockel durch die
Plastikabdeckung.
Die Mainboard Fotos, die in diesem Abschnitt gezeigt werden, sind fr Demonstration der
CPU/ Khler Installation. Das Aussehen Ihres mainboard kann abhangig von dem Modell
schwanken, das Sie kaufen. Das Aussehen Ihres Mainboards kann abhngig von dem
Modell schwanken, welches Sie erworben haben.
3.
Die Speichermodule haben nur eine Kerbe in der Mitte des Moduls. Sie passen nur in
einer Richtung in den Sockel.
Setzen Sie den DIMM- Speicherbaustein senkrecht in den DIMM- Sockel, dann
drcken Sie ihn hinein, bis die goldenen Kontakte tief im Sockel sitzen. Die
Plastikklammern an den Seiten des DIMM- Sockels schlieen sich automatisch.
berprfen Sie manuell, wenn die Speichermodule durch den DIMM- Sockel
eingerastet worden
Notch
Volt
41
Wichtig:
DDR2 und DDR knnen nicht untereinander getauscht werden und der Standard DDR2 ist
nicht rckwrtskompatibel, installieren Sie DDR2 Speichermodule stets in DDR2 DIMM
Slots und DDR Speichermodule stets in DDR DIMM Slots.
Um einen sicheren Systemstart zu gewhrleisten, bestcken Sie immer DIMM 1 zuerst.
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
GND
Res
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
+12V
GND
Wichtig:
Stellen Sie die Verbindung aller drei Anschlsse mit einem angemessenem ATX Netzteil
sicher, um den stabilen Betrieb des Mainboards sicher zu stellen.
Netzteile mit 350 Watt (und mehr) werden aus Grnden der Systemstabilitt dringend
empfohlen.
Die ATX 12V Stromversorgung sollte mit mehr als 18A erfolgen.
42
Gehusekontaktschalter: JCI1
Dieser Anschluss wird mit einem Kontaktschalter verbunden. Wird
das Gehuse geffnet, wird der Schalter geschlossen und das
System zeichnet dies auf und gibt auf dem Bildschirm eine
Warnung aus. Um die Warnmeldung zu lschen, muss das BIOS
aufgerufen und die Aufzeichnung gelscht werden.
GND
+12V
Sensor
Sensor
GND
+12V
2
1
GND
CINTRU
GND
SPDIF
VCC
CD-Eingang: CD_IN1
Dieser Anschluss wird fr externen Audioeingang zur Verfgung
gestellt.
8 7
JFP2
Speaker
Power
LED
2 1
+
-
JFP1
1 2
HDD
LED
Reset
Switch
- -
9 10
43
GND
Power
LED
Power
Switch
USB1+
USB1
N.C.(10)
Key,no pin(9)
USB0- GND
USB0+
GND
(2)VCC
(1)VCC
MIC2_JD
VCC5
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
DSR
DTR CTS
Key,no pin (10)
RI (9)
(2) SIN
(1) DCD
SOUT RTS
GND
12
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
44
1
2
3
1
2
3
Keep Data
1
2
3
Clear Data
Wichtig:
Sie knnen den CMOS lschen, indem Sie die Pins 2-3 verbinden, whrend das System
ausgeschaltet ist. Kehren Sie danach zur Pinposition 1-2 zurck. Lschen Sie den CMOS
nicht, solange das System angeschaltet ist, dies wrde das Mainboard beschdigen.
Der PCI Express x 16 Slot untersttzt die Datenubertragunsraten von bis zu 4.0 GB/s.
Die PCI Steckpltze untersttzt LAN Karte, SCSI Karte, USB Karte und andere
Zusatzkarten Karte,die mit PCI Spezifikationen bereinstimmen.
Wichtig:
Stellen Sie vor dem Einsetzen oder Entnehmen von Karten sicher, dass Sie den
Netzstecker gezogen haben. Studieren Sie bitte die Anleitung zur Erweiterungskarte, um
jede notwendige Hard - oder Softwareeinstellung fr die Erweiterungskarte vorzunehmen,
sei es an Steckbrcken (Jumpern), Schaltern oder im BIOS.
Reihenfolge2
Reihenfolge3
Reihenfolge4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
45
BIOS Setup
Nach dem Einschalten beginnt der Computer den POST (Power On Self Test Selbstberprfung nach Anschalten). Sobald die Meldung unten erscheint, drcken Sie die Taste <F2>
oder <DEL> , um das Setup aufzurufen.
Press DEL to enter SETUP
Sollten Sie die Taste nicht rechtzeitig gedrckt haben und somit den Start des BIOS
verpasst haben, starten Sie bitte Ihr System neu. Entweder drcken Sie dazu den "Power
On / Anschalter" oder den "Reset" Knopf. Alternativ bettigen Sie die Tastenkombination
<Ctrl>, <Alt> und <Delete>, um einen Neustart zu erzwingen.
Hauptseite
46
Cell Menu
47
48
49
50
G31M3 V2 (MS-7529 v1.x) Micro-ATX.
G31M3 V2
51
TM
TM
FSB
z 800/ 1066/ 1333
z : Intel G31
z : Intel ICH7
LAN()
z
z
z
z
z Realtek ALC888
z 8-
z Vista Premium
IDE
z 1 IDE ICH7
z Ultra DMA 66/100
52
SATA
z 2 SATA II ICH7
z 4- SATA II
z 3Gb/s
z 1
z 1 FDD 360KB, 720KB, 1.2MB, 1.44MB 2.88 MB.
TPM ()
z TPM
z
- 1 PS/2
- 1 PS/2
- 1 (COM1)
- 1 VGA
- 1 SPP/EPP/ECP
- 4 USB 2.0
- 1 RJ-45 LAN
- 3/6 ()
z ,
- 2 USB 2.0
- 1 CD-In
- 1 S/PDIF-Out
- 1
- 1
- 1 TPM ()
- 1
- 1 SPI Debugging
z Micro-ATX (24.4 X 19.3 )
z 6
:
3 , 8-
7- 8-
.
53
, ,
, .
, , ,
, ... ,
.
LGA775
.
/ .
.
.
LGA 775
LGA 775
.
LGA 775
.
1.
,
. ,
.
2.
, .
54
3.
4.
5.
6.
,
. ,
.
7.
. ,
.
8.
9.
.
.
10.
.
,
.
11. .
(
) .
12. ,
.
:
BIOS.
,
.
, ,
.
, .
1.
.
.
2.
DIMM .
, DIMM .
DIMM , .
,
.
3.
, DIMM
.
55
Notch
Volt
:
DDR2 DDR, DDR2
. DDR2
DDR2.
, DIMM1.
24-
ATX: ATX1
24-
ATX .
, ,
.
.
. 20
(. ).
ATX
12: JPW1
12
.
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
GND
+5V
GND
GND
GND
+5V
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
+12V
GND
, ATX .
350 ( )
.
: FDD1
360, 720, 1.2, 1.44 2.88.
56
PS-ON#
GND
ATX 12 18.
Res
GND
IDE: IDE1
IDE,
IDE .
:
IDE,
Slave
. ,
, ,
.
:
CPUFAN1, SYSFAN1, SYSFAN2
+12. ,
+12, -
GND.
,
.
: JCI1
, .
.
.
BIOS.
GND
+12V
Sensor
Sensor
GND
+12V
2
1
GND
CINTRU
S/PDIF-Out: JSPD1
GND
SPDIF
VCC
S/PDIF (Sony & Philips Digital Interconnect Format)
.
CD-In: CD_IN1
.
57
GND
Speaker
Power
LED
2 1
HDD
LED
Reset
Switch
JFP1
1 2
- -
. JFP1
8 7
JFP2
: JFP1, JFP2
Power
LED
Power
Switch
9 10
USB :
JUSB1, JUSB2
, Intel
I/O Connectivity Design Guide,
USB HDD, , MP3
, , ..
: JAUD1
. Intel Front
Panel I/O Connectivity Design Guide.
USB1+
USB1-
GND
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
MIC2_JD
VCC5
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
SPI: JSPI1
.
: JCOM1
16550A,
16- FIFO.
.
DSR
DTR CTS
Key,no pin (10)
RI (9)
(2) SIN
(1) DCD
SOUT RTS
GND
12
TPM :
JTPM1()
TPM (Trusted Platform Module) ().
TPM.
58
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
CMOS: JBAT1
CMOS
,
. , CMOS ,
.
( CMOS), .
1
2
3
1
2
3
1
2
3
Keep Data
Clear Data
:
CMOS 2-3 .
1-2.
CMOS : .
PCI
IRQ Interrupt ReQuest (line) ,
, .
IRQ PCI PCI :
Order1
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
59
BIOS
. (POST) <DEL>.
DEL, SETUP
,
.
RESET <Ctrl>, <Alt> <Delete>.
60
Cell Menu
Enhanced
Intel
SpeedStep
AC.
, Disabled.
,
Speedstep.
Adjust CPU FSB Frequency()
Auto Detect CPU Frequency [Disable],
FSB .
61
62
BIOSa,
.
63
64
TM
Intel ICH7 . LGA775 Intel Core 2
Duo/ Core
TM
G31M3 V2 ,.
65
CPU
TM
TM
z LGA 775 Intel Core 2 Duo/ Core 2 Quad/ Pentium Dual-Core E2XXX
Celeron 4XXX/ Wolfdale
z CPU:
1. E8190 ~ E8600
2. E7200 ~ E7300
3. E6300 ~ E6850
4. E4300 ~ E4700
5. E2100 ~ E2200
6. E1200 ~ E1600
7. 420 ~ 460
CPU CPU
z 4 CPU
z TDP 95W
( CPU ,:http://global.msi.com.tw/index.php?func=cpuform)
FSB
z 800/ 1066/ 1333 MHz
z : Intel G31
z : Intel ICH7
LAN ()
z
z
z
z
z Realtek ALC888
z 8
z Vista Premium
IDE
z ICH7 1 IDE
z Ultra DMA 66/ 100
z PIO,,
SATA
z ICH7 2 SATA II
z 4 SATA II
66
z 3Gb/s
z 1
z 1 360K, 720K, 1.2M, 1.44M 2.88Mbytes FDD
TPM ()
z TPM
z
- 1 PS/2
- 1 PS/2
- 1 (COM1)
- 1 VGA
- 1 SPP/EPP/ECP
- 4 USB 2.0
- 1 RJ-45 LAN
- 3/6 ()
z /
- 2 USB2.0
- 1 CD-In
- 1 SPDIF-Out
- 1
- 1
- 1 TPM ()
- 1
- 1 SPI Debugging
z 1 PCI Express x 16
z 2 PCI
z 3.3V/ 5V PCI
z 6
:
3 , 8 ,.
67
CPU,,,.
,,.,.
LGA775 CPU
CPU , CPU CPU ,
. , CPU
.
CPU . CPU .
LGA 775 CPU
LGA 775 CPU .
1.
CPU , CPU .
CPU ,,
.
2.
,.
3.
4.
5.
CPU .
6.
CPU , CPU .
CPU . CPU
68
.
7.
CPU ,, CPU
.
8.
9.
,.
10. ,,
.
11. .,(
).
12. ,.
:
BIOS CPU .
CPU, CPU ,.
CPU ,.
1. . .
2. DIMM .
DIMM .
3. DIMM
Notch
Volt
:
DDR2 DDR DDR2 DDR2 DDR2
DIMM
DIMM1
69
+3.3V
GND
+12V
+5V
+12V
+5V
,,,
5VSB
+5V
PWR OK
Res
GND
GND
+5V
GND
GND
GND
+5V
23 24 .()
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
12V CPU .
+12V
GND
:
ATX .
, 350 ().
ATX 12V 18A.
: FDD1
360KB, 720KB, 1.2MB, 1.44MB 2.88MB
.
IDE : IDE1
IDE , IDE .
:
,
..
70
Control
Sensor
+12V
GND
GND
+12V
Sensor
Sensor
GND
+12V
: JCI1
BIOS
2
1
GND
CINTRU
GND
SPDIF
VCC
S/PDIF-Out : JSPD1
SPDIF(Sony &
Philips ).
CD-In : CD_IN1
CD-ROM .
GND
8 7
: JFP1, JFP2
Speaker
JFP2
Power
LED
2 1
+
-
- +
HDD
LED
Reset
Switch
JFP1
1 2
Power
LED
Power
Switch
9 10
USB1+
USB1-
GND
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
MIC2_JD
: JAUD1
VCC5
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
Intel I/O .
: JCOM1
DSR
DTR CTS
16550A ,/ 16 bytes
FIFOs..
(2) SIN
(1) DCD
SOUT RTS
GND
71
TPM : JTPM1 ()
12
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
CMOS : JBAT1
CMOS RAM
.CMOS RAM
1
2
3
1
2
3
1
2
3
Keep Data
Clear Data
. CMOS
RAM JBAT1 ( CMOS )
. .
:
, 2-3 CMOS ., 1-2 .
CMOS..
PCI () Express
PCI Express PCI Express .
PCI ()
PCI ,SCSI ,USB , PCI .
:
,.,
,, BIOS .
PCI
IRQ ,.
Order1
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
72
BIOS
POST (). <DEL>
.
Press DEL to enter SETUP
. Setup, RESET
.<Ctrl>, <Alt><Delete> .
73
Intel EIST
Intel SpeedStep AC ,
CPU ,Disabled. CPU speedstep .
Adjust CPU FSB Frequency (MHz)
Auto Detect CPU Frequency [Disable], CPU FSB .
Adjusted CPU Frequency
CPU (FSB x Ratio)..
Advance DRAM Configuration > DRAM CAS# Latency
CAS DRAM [2T][2.5T]
[By SPD] DRAM CAS# BIOS DRAM SPD
(Serial Presence Detect) EEPROM
74
FSB/Memory Ratio
Auto Detect DRAM Frequency [Disable], FSB/Ratio.
Adjusted DDR Memory Frequency
DRAM ..
Adjust PCI-E Frequency (MHz)
PCIE ( MHZ).
Auto Disable DIMM/PCI Frequency ( DIMM/PCI )
DIMM/PCI .[Enabled],(EMI),
DIMM/PCI ().
Spread Spectrum ()
,() EMI().
,.
, Disabled,.
, Enabled,.,,
.(),
..
:
EMI [Disabled]
EMI Spread Spectrum EMI
Spread SpectrumEMI Spread
Spectrum( EMI
Spread Spectrum
75
76
G31M3 V2 (MS-7529 v1.X) Micro-ATX G31M3 V2
TM
TM
Intel G31 & Intel ICH7 LGA775 Intel Core 2 Duo/ Core 2
Quad/ Pentium Dual-Core E2XXX Celeron 4XXX/ Wolfdale G31M3 V2
77
TM
TM
E8190 ~ E8600
E7200 ~ E7300
E6300 ~ E6850
E4300 ~ E4700
E2100 ~ E2200
E1200 ~ E1600
420 ~ 460
CPU CPU
z 4 pin
z CPU TDP 95W
( CPU :
http://global.msi.com.tw/index.php?func=cpuform)
FSB
z FSB 800/ 1066/ 1333 MHz
z : Intel G31
z : Intel ICH7
LAN()
z
z
z
z
z Realtek ALC888
z 8
z Microsoft Vista Premium
IDE
78
SATA
z
z 360KB, 720KB, 1.2MB, 1.44MB 2.88MB
TPM()
z TPM
z
- PS/2
- PS/2
- (COM1)
- VGA
- SPP/EPP/ECP
- USB2.0
- RJ-45
- ()
z
- USB2.0
- CD-In
- S/PDIF-out
-
-
- TPM ()
-
- SPI
z
:
(
)
79
LGA775
LGA775
LGA775 CPU
LGA775 CPU
Pin1
1.
Pin1
2.
3.
4.
5.
6.
CPU
7.
CPU CPU
8.
80
9.
10.
11.
12.
:
BIOS CPU
CPU CPU
1.
2.
DIMM .
3.
DIMM
Notch
Volt
:
DDR2 DDR DDR DDR2
DDR2
DIMM1
81
ATX 20-pin
ATX 20-pin pin 1 pin
13 ()
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
Res
GND
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
12V CPU
+12V
GND
:
ATX
350
ATX 12V 18
: FDD1
360 KB, 720 KB, 1.2
MB, 1.44 MB 2.88 MB
IDE : IDE1
IDE
:
Jumper
82
: CPUFAN1, SYSFAN1,
SYSFAN2
Control
Sensor
+12V
GND
+12V
+12V
GND
CPU
GND
+12V
Sensor
Sensor
GND
+12V
: JCI1
BIOS
2
1
GND
CINTRU
S/PDIF-Out : JSPD1
GND
SPDIF
VCC
CD-In : CD_IN1
GND
8 7
: JFP1, JFP2
LED
JFP2
Speaker
Power
LED
2 1
+
-
- +
HDD
LED
Reset
Switch
JFP1
1 2
Power
LED
Power
Switch
9 10
USB1+
USB1-
GND
Intel I/O
USB USB MP3
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
: JAUD1
Intel
I/O
MIC2_JD
VCC5
(2)GND
(1)MIC_L
NC
Line_JD(10)
Line-out_L(9)
83
SPI : JSPI1
: JCOM1
DSR
DTR CTS
/ 16 FIFOs 16550A
(2) SIN
(1) DCD
SOUT RTS
GND
TPM :
JTPM1 ()
()
12
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
CMOS : JBAT1
CMOS RAM
CMOS RAM
1
2
3
1
2
3
Keep Data
1
2
3
Clear Data
:
2-3 CMOS 1-2
CMOS
PCI Express
PCI Express PCI Express
PCI Express x 16 4.0 GB
PCI
PCI SCSI USB PCI
BIOS
84
PCI
IRQ (Interrupt request)
PCI IRQ PCI
Order1
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
BIOS
POST () <DEL>
Integrated Peripherals ()
85
H/W Monitor
Cell Menu
86
Intel EISTIntel
AC
SpeedStep CPU
Adjust CPU FSB Frequency (MHz) CPU FSB
[Disable] CPU FSB
Adjusted CPU Frequency CPU
CPU (FSB x Ratio)
Advance DRAM Configuration > DRAM CAS# Latency
DRAM [2T]
[2.5T][By SPD] BIOS DRAM SPD
EEPROM DRAM
FSB/Memory RatioFSB/ Ratio
FSB/ Ratio
Adjusted DDR Memory Frequency
:
EMI
.
87
88
G31M3 V2 (MS-7529 v1.x)Micro-ATX
TM
TM
LGA 775 Intel Core 2 Duo/ Core 2 Quad/ Pentium Dual-Core E2XXX Celeron 4XXX/
Wolfdale
89
TM
TM
z LGA 775 Intel Core 2 Duo/ Core 2 Quad/ Pentium Dual-Core E2XXX Celeron
4XXX/ Wolfdale
z CPU
1. E8190 ~ E8600
2. E7200 ~ E7300
3. E6300 ~ E6850
4. E4300 ~ E4700
5. E2100 ~ E2200
6. E1200 ~ E1600
7. 420 ~ 460
CPU CPU
z 4 CPU
z TDP 95W
( CPU
http://global.msi.com.tw/index.php?func=cpuform)
FSB
z 800/ 1066/ 1333 MHz
z : Intel G31
z : Intel ICH7
LAN()
z
z
z
z
z Realtek ALC888
z 8
z Vista Premium
IDE
z 1 IDE ICH7
90
SATA
z 2 SATA II ICH7
z 4 SATAII
z 3Gb/s
z 1
z 360KB, 720KB, 1.2MB, 1.44MB 2.88MB FDD 1
TPM ()
z TPM
z
- 1 PS/2
- 1 PS/2
- 1 (COM1)
- 1 VGA
- 1 SPP/EPP/ECP
- 4 USB 2.0
- 1 RJ-45 LAN
- 3/6 ()
z /
- 2 USB 2.0
- 1 CD-In
- 1 S/PDIF-Out
- 1
- 1
- 1 TPM ()
- 1
- 1 SPI
91
z 6
:
3 8
7 8 ()
92
LGA775 CPU
CPU CPU
CPU
CPU CPU
CPU
LGA 775 CPU
LGA 775 CPU
1.
CPU ()
2.
CPU
3.
CPU
4.
93
5.
6.
CPU () CPU
7.
CPU
8.
9.
10. CPU
11.
12.
:
CPU BIOS
CPU CPU
CPU
1.
2.
3.
DIMM
Notch
Volt
94
:
DDR2 DDR DDR2
ATX 24 : ATX1
ATX 24
20 ATX 1/13
()
+3.3V
GND
+12V
+5V
+12V
+5V
5VSB
+5V
PWR OK
GND
Res
GND
+5V
GND
GND
GND
+5V
PS-ON#
GND
GND
+3.3V
-12V
+3.3V
+3.3V
+12V
GND
12V CPU
+12V
GND
350W
ATX 12V 18A
FDD : FDD1
360 KB, 720 KB, 1.2MB, 1.44MB 2.88MB
IDE : IDE1
IDE IDE
:
2 2
95
:
ATA 90
: CPUFAN1, SYSFAN1,
SYSFAN2
Control
Sensor
+12V
GND
+12V
+12V GND
GND
+12V
Sensor
Sensor
GND
+12V
: JCI1
2
1
GND
CINTRU
BIOS
S/PDIF-Out : JSPD1
GND
SPDIF
VCC
SPDIF(Sony& Philips
Digital Interconnect Format)
CD-In : CD_IN1
8 7
JFP2
Speaker
Power
LED
2 1
+
-
JFP1
1 2
HDD
LED
Reset
Switch
- -
LED
GND
: JFP1, JFP2
Power
LED
Power
Switch
9 10
USB1+
USB1-
GND
96
N.C.(10)
Key,no pin(9)
(2)VCC
(1)VCC
USB0- GND
USB0+
:
JAUD1
Intel I/O
MIC2_JD
VCC5
NC
Line_JD(10)
Line-out_L(9)
(2)GND
(1)MIC_L
SPI : JSPI1
: JCOM1
JCOM1
JCOM1
16550A 16 FIFO
TPM : JTPM1(
)
TPM (Trusted Platform Module)
TPM
DSR
DTR CTS
Key,no pin (10)
RI (9)
(2) SIN
(1) DCD
SOUT RTS
GND
12
3Vdual/ 3V_STB
VCC3
SIRQ
VCC5
KEY
GND
GND
LCLK
LRST#
LAD0
LAD1
LAD2
LAD3
LFRAME#
13 14
CMOS : JBAT1
CMOS RAM
BIOS
CMOS RAM
OS
CMOS
1
2
3
1
2
3
Keep Data
1
2
3
Clear Data
:
CMOS 2-3
1-2 CMOS
PCI Express
PCI Express PCI Express
97
PCI
PCI
BIOS
PCI
IRQinterrupt request line
PCI IRQ PCI
INT A# INT D#:
Order1
Order2
Order3
Order4
PCI Slot1
INT A#
INT B#
INT C#
INT D#
PCI Slot2
INT B#
INT C#
INT D#
INT A#
BIOS
POST (Power On Self Test)
<DEL>
Press DEL to enter SETUP
<DEL><RESET>
<Ctrl><Alt><Delete>
98
Integrated Peripherals
IDE, I/O
Power Management Setup
H/W Monitor
CPU
BIOS Setting Password
Cell Menu
/
Load Fail-Safe Defaults
BIOS
Load Optimized Defaults
BIOS
Save & Exit Setup
CMOS
Exit Without Saving
CMOS
99
Cell Menu
Intel EIST
Enhanced Intel Speed Step PC
AC CPU
[Disabled] CPU
FSB/Memory Ratio
[Auto Detect DRAM Frequency][Disable] FSB/
100
Disabled
:
[Disabled]
[Enabled]
Spread Spectrum
[Disabled]
101
(PBDE)
//
O SJ/T11363-2006
X SJ/T11363-2006
:
0.35% 0.4% 4%
-( 85%)
-
(pins)(microprocessors)
80~85%
(Flip Chippackages)