Professional Documents
Culture Documents
Pioneer Pdp-504pu Pe Pro-504pu SM (ET)
Pioneer Pdp-504pu Pe Pro-504pu SM (ET)
ARP3176
PDP-504PU
PLASMA DISPLAY
PDP-504PE PRO-504PU
Model
PDP-504PU PDP-504PE PDP-504PE PRO-504PU TUCK WYVI6 WYVI6XK KUC
PDP-504PU
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Type Power Requirement
AC110 - 240V AC220 - 240V AC220 - 240V AC120V
Remarks
This service manual should be used together with the following manual(s).
Model No.
PDP-504PU/ TUCK PDP-504PE/ WYVI6 PDP-504PE/ WYVI6XK PRO-504PU/ KUC
Order No.
ARP3177
Remarks
SCHEMATIC DIAGRAM and PCB CONNECTION DIAGRAM
Confirm it
Serial No.
WYVI6 For details, refer to "Important symbols for good services". WYVI6XK
SS UK
PIONEER CORPORATION
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
SAFETY INFORMATION
A
This service manual is intended for qualified service technicians ; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 - Proposition 65
NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or must be of identical designation.
REMARQUE (POUR MODLE CANADIEN SEULEMENT) Les symboles de fusible (fusible de type rapide) et/ou de remplacement doivent avoir la mme dsignation.
SAFETY PRECAUTIONS
NOTICE : Comply with all cautions and safety related notes located on or inside the cabinet and on the chassis. The following precautions should be observed : 1. When service is required, even though the PDP UNIT an isolation transformer should be inserted between the power line and the set in safety before any service is performed. 2. When replacing a chassis in the set, all the protective devices must be put back in place, such as barriers, nonmetallic knobs, adjustment and compartment covershields, isolation resistorcapacitor, etc. 3. When service is required, observe the original lead dress. Extra precaution should be taken to assure correct lead dress in the high voltage circuitry area. 4. Always use the manufacture's replacement components. Especially critical components as indicated on the circuit diagram should not be replaced by other manufacture's. Furthermore where a short circuit has occurred, replace those components that indicate evidence of overheating. 5. Before returning a serviced set to the customer, the service technician must thoroughly test the unit to be certain that it is completely safe to operate without danger of electrical shock, and be sure that no protective device built into the set by the manufacture has become defective, or inadvertently defeated during servicing. Therefore, the following checks should be performed for the continued protection of the customer and servicetechnician. 6. Perform the following precautions against unwanted radiation and rise in internal temperature. Always return the internal wiring to the original styling. Attach parts (Gascket, Ferrite Core, Ground, Rear Cover, Shield Case etc.) surely after disassembly. 7. Perform the following precautions for the PDP panel. When the front case is removed, make sure nothing hits the panel face, panel corner, and panel edge (so that the glass does not break). Make sure that the panel vent does not break. (Check that the cover is attached.) Handle the FPC connected to the panel carefully. Twisting or pulling the FPC when connecting it to the connector will cause it to peel off from the panel. 8. Pay attention to the following. When the front case is removed, infrared ray is radiated and may disturb reception of the remote control unit. Pay extreme caution when the front case and rear panel are removed because this may cause a high risk of disturbance to TVs and radios in the surrounding.
2
1 2
PDP-504PU
3 4
Earth ground
AC Leakage Test
ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE SET TO THE CUSTOMER.
E
PDP-504PU
5 6 7 8
Charged Section
A
The places where the commercial AC power is used without passing through the power supply transformer. If the places are touched, there is a risk of electric shock. In addition, the measuring equipment can be damaged if it is connected to the GND of the charged section and the GND of the non-charged section while connecting the set directly to the commercial AC power supply. Therefore, be sure to connect the set via an insulated transformer and supply the current.
1. AC Power Cord 2. AC Inlet with Filter 3. Power Switch (S1) 4. Fuse (In the POWER SUPPLY Unit) 5. STB Transformer and Converter Transformer (In the POWER SUPPLY Unit) 6. Other primary side of the POWER SUPPLY Unit
: Part is Charged Section. : Part is the High Voltage Generating Points other than the Charged Section.
50 Y DRIVE Assy
50 SCAN B Assy
50 SCAN A Assy
Fig.1 Charged Section and High Voltage Generating Point (Rear View)
4
1 2
PDP-504PU
3 4
1. Product safety
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual.
2. Adjustments
To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable. In accordance with the procedures or instructions described in this manual, adjustments should be performed.
3. Cleaning
For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning, proper cleaning should be performed to restore their performances.
B
PDP-504PU
5 6 7 8
CONTENTS
SAFETY INFORMATION ...................................................................................................................................................... 2 1. SPECIFICATIONS .............................................................................................................................................................. 7 2. EXPLODED VIEWS AND PARTS LIST .......................................................................................................................... 8 2.1 PACKING ...................................................................................................................................................................... 8 2.2 CHASSIS SECTION (1) .......................................................................................................................................... 10 2.3 CHASSIS SECTION (2) .......................................................................................................................................... 12 2.4 FLAME SECTION .................................................................................................................................................... 14 2.5 MULTI BASE SECTION .......................................................................................................................................... 16 2.6 REAR SECTION....................................................................................................................................................... 18 2.7 FRONT PANEL SECTION ...................................................................................................................................... 20 2.8 PANEL CHASSIS (50) Assy (AWU1081) ............................................................................................................. 21 2.9 PDP SERVICE Assy (AWU1080) .......................................................................................................................... 21 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM (For SCHEMATIC DIAGRAM, Refer to ARP3177) ................ 22 3.1 BLOCK DIAGRAM ................................................................................................................................................... 22 3.1.1 OVERALL BLOCK DIAGRAM......................................................................................................................... 22 3.1.2 50 Y DRIVE ASSY ............................................................................................................................................ 24 3.1.3 50 X DRIVE ASSY ............................................................................................................................................ 25 3.1.4 PANEL IF ASSY ................................................................................................................................................ 26 3.1.5 DIGITAL VIDEO ASSY ..................................................................................................................................... 31 3.1.6 HD AUDIO AMP ASSY .................................................................................................................................... 33 3.2 WAVEFORMS ........................................................................................................................................................... 34
4. PCB CONNECTION DIAGRAM (Refer to ARP3177)
5. PCB PARTS LIST ............................................................................................................................................................ 39 6. ADJUSTMENT ................................................................................................................................................................. 47 6.1 ADJUSTMENT REQUIRED WHEN THE SET IS REPAIRED OR REPLACED ............................................ 47 6.2 COMMAND................................................................................................................................................................ 47 6.2.1 RS232C COMMAND ........................................................................................................................................ 47 7. GENERAL INFORMATION ............................................................................................................................................ 54 7.1 DIAGNOSIS............................................................................................................................................................... 54 7.1.1 PCB LOCATION ................................................................................................................................................ 54 7.1.2 DIAGNOSIS OF SHUTDOWN/POWER-DOWN INDICATED BY LEDS ................................................. 55 7.1.3 DIAGNOSIS WITH THE AID OF FACTORY MODE .......................................................................... 60 7.1.4 TROUBLE SHOOTING .................................................................................................................................... 62 7.1.5 CANCELING DETECTION BY THE TRAP SWITCH ........................................................................ 63 7.1.6 OPERATION WHEN THE MEDIA RECIVER IS NOT CONNECTED ................................................ 64 7.1.7 TEMPERATURE-COMPENSATION FUNCTION OF THE DRIVE-SYSTEM VOLTAGE.................... 64 7.1.8 POWER ON/OFF FUNCTION FOR THE LARGE-SIGNAL SYSTEM ..................................................... 65 7.1.9 BACKING UP THE ADJUSTMENT VALUES FOR THE MAIN UNIT................................................. 66 7.1.10 DISASSEMBLY ............................................................................................................................................... 68 7.2 IC INFORMATION .................................................................................................................................................... 71 8. PANEL FACILITIES AND SPECIFICATIONS ............................................................................................................. 99
6
1 2
PDP-504PU
3 4
1. SPECIFICATIONS
5 0 " P la sma Di s p l a y
Item Number of P i x e l s Audio Amp l i fi e r Surround S y s te m Mo d e l: P D P -504P U 1 2 8 0 x 7 6 8 p i xel s 1 3 W + 1 3 W (1kH z, 10% , 8) S R S /F OC U S /T ruB ass M odel : P D P - 504P E 1280 x 768 pi xel s 13 W + 13 W ( 1kH z, 10%, 8 ) S R S /FOC U S / Tr uB ass 220-240V AC , 50/ 60H z, 352W (0.5W S tan dby) 1270(W ) x 7 37 ( H ) x 98 ( D ) m m 38 kg (83.8 l bs. )
B A
Power Req u i re m e n t 1 1 0 -2 4 0 V A C ,50/60H z,363W (0 .3 W S ta n d b y,120V ) Dimens ion s Weight 1 2 7 0 (W ) x 7 3 7 (H ) x 98 (D ) mm (5 0 (W )x 2 9 (H )x 3 7 /8 (D )i nches) 3 8 kg (8 3 .8 l b s.)
Accessories
Power Cord Speaker Cushion x1 (AEB1384) Wiping Cloth x1 (AED1208)
D
(PDP-504PE: ADG1214) (Except PRO-504PU) Binder Assy (AEC1908) Bead Bands x3 (PDP-504PU: ADG1215) (PRO-504PU: ADG1215) (PDP-504PE only) Speed Clamp x3 Ferrite Core (ATX1039) Cable Tie
E
PDP-504PU
5 6 7 8
Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.)
2.1 PACKING
PDP-504PU / TUCK PDP-504PE / WYVI6 PDP-504PE / WYVI6XK types
B
14
14 4
10
20
23 9 12
10 18 16 8 9
D
20 6 6 5 18
15 7
13
13
8
1 2
PDP-504PU
3 4
Description Power Cord Power Cord Wiping Cloth Binder Assy Code Case Center Pad (50) Warranty Card Mirror Mat Pad (PP T- L) Pad (PP T- R) Pad (PP B- L) Pad (PP B- R)
Part No. See Contrast table (2) See Contrast table (2) AED1208 AEC1908 See Contrast table (2) AHA2335 See Contrast table (2) See Contrast table (2) AHA2315 AHA2316 AHA2343 AHA2344
Mark No. 13 14 15 16 17 18 19 20 21 22 23
Description Carton (50) Upper Carton (50) Vinyl Bag Caution Card Speaker Cushion Vinyl Bag S Ferrite Core Inner Carton Polyethirene Sheet Paper Sub Carton
Part No. See Contrast table (2) See Contrast table (2) AHG1310 ARM1232 See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2)
A
1 2 3 4 5
6 NSP 7 8 9 10 11 12
(2) CONTRAST TABLE PDP-504PU/ TUCK, PDP-504PE/ WYVI6, PDP-504PE/ WYVI6XK and PRO-504PU/ KUC are constructed the same except for the following :
Mark No. > > NSP 1 Power Cord 2 5 7 8 Power Cord Code Case Warranty Card Mirror Mat Symbol and Description PDP-504PU TUCK ADG1215 Not used AHC1041 ARY1138 AHG1284 AHD3177 Not used Not used AHD3178 Not used Not used Not used AEB1384 AHG1338 Not used Not used Not used Not used AHB1248 PDP-504PE WYVI6 Not used ADG1214 AHC1041 ARY1114 AHG1284 AHD3177 Not used Not used Not used AHD3203 Not used Not used AEB1384 AHG1338 ATX1039 Not used Not used Not used AHB1248 PDP-504PE WYVI6XK Not used ADG1214 AHC1049 ARY1114 AHG1327 Not used AHD3191 Not used Not used Not used AHD3190 Not used AEB1384 Not used ATX1039 Not used Not used Not used AHB1248 PRO-504PU KUC ADG1215 Not used Not used ARY1134 AHG1284 Not used Not used AHD3222 Not used Not used Not used AHD3223 Not used AHG1338 Not used AHB1251 AHG1341 AHG1343 Not used
E C
13 Carton (50) 13 Carton (50) 13 Carton (50EL) 14 14 14 14 17 18 19 20 21 Upper Carton (50PU) Upper Carton (504PE) Upper Carton (50) Upper Carton (50EL) Speaker Cushion Vinyl Bag S Ferrite Core Inner Carton Polyethirene Sheet
PDP-504PU
5 6 7 8
15
17
15
17
15
17
17 15
15
20 21
16
16
15
21
15 15
B
15
18
19
15
17
15
17
17
15
17 15
22
22
22
14
23
14
14
8 15 4
10
14
11 22
14 22 2
12 22
14
13
10
1 2
PDP-504PU
3 4
ADD1233 ADD1234 ADD1235 AEC1879 AEC1941 AEC1938 AEC1745 AEC1947 AEC1948 AEH1066 AEH1065 VBB30P080FNI ADD1229
PDP-504PU
5 6 7 8
11
20
9
B
100V
20
11
19 10 15
3 15
12
15
C
15
14
13
18
E
2 17 17 16 16 16 17
8 17 15 16 18 17 16 18 17
16
Upper side
16
Upper side
12
1 2
PDP-504PU
3 4
ADX2853 ADX2854 ADX2857 ADX2855 ABZ30P060FMC PMB30P060FNI VBB30P080FNI PMB40P080FZK ADX2839 AEC1671
PDP-504PU
5 6 7 8
13
17
19
19
17
17
11
11
18
10
11 19
18
11 19
18
11
11
17
Upper side
14
B
3 14 4 14 17 12 13 14
17
17
C
17
15
16
17
23
D
21
24
8 19 9 20 19 17 22 2 5
18 7 1 19 19
18
17
17
17
11
11
18
10
11
11 18 25 18
11
11
17
14
1 2
PDP-504PU
3 4
6 NSP 7 8 9 NSP 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
AMR3369 ANG2638 ANG2561 AEC1745 ANA1765 ANA1766 AMZ30P060FZK APZ30P080FZK AMZ30P080FMC ABZ30P060FMC AEC1884 ADD1225 AEC1879 ANK1725 AEB1397
PDP-504PU
5 6 7 8
15
19 6 8
B
5 13 18 11 14 10 14 13 15
9 13
14
17
17
17
E
17 17 17
17
20
21
17
16
17
17
16
1 2
PDP-504PU
3 4
AEC1940 AEC1946 AEC1884 AEC1941 BEC1136 APZ30P080FZK AMZ30P060FZK PMB30P060FNI ABA1294 BBA1051 PMZ26P060FZK
PDP-504PU
5 6 7 8
17
3 8 8 8 9 1 8
4 9 8 8
8 9
7
B
7 2 2 7 7 9 8 8 8 9 8
18
1 2
PDP-504PU
3 4
(2) CONTRAST TABLE PDP-504PU/ TUCK, PDP-504PE/ WYVI6, PDP-504PE/ WYVI6XK and PRO-504PU/ KUC are constructed the same except for the following :
Mark No. NSP 3 Name Label 4 Caution Label 5 Terminal Label Symbol and Description PDP-504PU TUCK AAL2469 AAX3007 AAX2997 PDP-504PE WYVI6 AAL2488 AAX3007 AAX2998 PDP-504PE WYVI6XK AAL2481 AAX3005 AAX3006 PRO-504PU KUC AAL2500 AAX3007 AAX2997
B
PDP-504PU
5 6 7 8
19
4 1 12 3 6 6 13 7
B
14 6 3 14 13
7 8
15 14 7 6
C
7 5 7 14 6 15 6
10
13
11 Rear side 2
20
1 2
PDP-504PU
3 4
(2) CONTRAST TABLE PDP-504PU/ TUCK, PDP-504PE/ WYVI6, PDP-504PE/ WYVI6XK and PRO-504PU/ KUC are constructed the same except for the following :
Mark No. Symbol and Description PDP-504PU TUCK AMR3385 AMB2763 AAD4123 PDP-504PE WYVI6 AMR3348 AMB2763 AAD4123 PDP-504PE WYVI6XK AMR3348 AMB2763 AAD4123 PRO-504PU KUC AMR3348 AMB2804 AAD4126
2..Address Module (IC1-IC40) AXF1116 2..Plasma Panel Assy(50")(V1)AAV1244 2..FPC (50XGA-X) ADY1084 2..FPC (50XGA-Y) ADY1085 2..Chassis Assy (50) ANA1774
NSP
ZTX-2102Y45-5
Part No. AWU1081 ANA1733 ANA1765 ANA1766 ANG2559 ANG2561 AEC1745 AEC1884 AEC1938 AEC1941 AEC1947 AEC1948 AEB1397 AED1226 AED1199
6
Mark No.
Description
Part No.
E
2..Front Spacer AMR3369 2..Caution Label AAX3031 NSP 2..Drive Voltage Label ARW1097 2..Front Case (504 Service) AMB2811 (Note) 2..Rear Case (50P) ANE1614 (Note) Note: The front case (504 Service) and rear case (50P) attached to the Service Assy are for transportation only. Do NOT use them as parts of the unit. 2..Screw AMZ30P060FZK 2..Screw AMZ30P080FMC 2..Screw AMZ30P080FZK 2..Screw PMB30P060FNI 2..Screw VBB30P080FNI 2..Screw ABZ30P100FZK
PDP-504PU
7 8
21
V+5V V+3V_LVDS V+3V_PLL V+3V_IC5 IC1501 AD1 CN1501 V+9V V+60V V+ADR RESONANCE BLOCK
V+5V V+3V_LVDS V+3V_PLL V+3V_IC5 IC1501 AD1 CN1501 V+9V V+60V V+ADR RESONANCE BLOCK
50 ADDRESS ASSY
50 ADDRESS ASSY
CN5501
CN5503 D7 ADR_PD3
50 SCAN B ASSY
IC5V ADD SEL_PULSE IC3201 VCC IC5V _VH ADD SEL_PULSE IC3202 VCC IC5V _VH ADD SEL_PULSE IC3203 VCC IC5V _VH ADD SEL_PULSE IC3204 VCC IC5V _VH ADD SEL_PULSE IC3205 VCC IC5V _VH ADD SEL_PULSE IC3206 VCC SB1 _VH PSUS CN3201 CN2101 SCAN
VCC_VH V_IC5V Y2
50 Y DRIVE ASSY
VCC_VH V_IC5V Y4 CN2301 V_OFS VC_VFVC_VF+ DC_DC CONV BLOCK VSUS
ADR_ PD0
V+6.5V
+5V
REGULATOR
+6.5V
MASK MOD IC2307 +5V +16.5V SOFT-D BLOCK Drive Signal Y1 D13
OR
D1
D14 CN2001 CN5521 LOGIC BLOCK +5V +16.5V SCAN YSUS SUB-FILD CONV. & XY DRV SEQUENCE PATTERN GEN. IC5401 PD5856A
XSUS
RESONANCE BLOCK +16.5V VSUS +RESET BLOCK PSUS Drive Signal VH_UV_PD YDRIVE_PD YRESNC_PD YDD_CHV_PD IC5V_UV_PD
IC5V
VCC _VH
CN3001
SCAN SA1
CN2102
ADD SEL_PULSE IC3001 VCC IC5V _VH ADD SEL_PULSE IC3002 VCC IC5V _VH ADD SEL_PULSE IC3003 VCC IC5V _VH ADD SEL_PULSE IC3004 VCC IC5V _VH ADD SEL_PULSE IC3005 VCC IC5V _VH ADD SEL_PULSE IC3006
PD
MASK
PD_MUTE +5V +15V VSUS Drive Signal Vofs MODULE UCOM IC5201 RELAY, PD_TRIGGER
PSUS
LVDS
PSIZE
Scan Signal Y3
50 SCAN A ASSY
ADR_PD5 D9 CN5506
ADR_PD7 D11
50 ADDRESS ASSY
RESONANCE BLOCK V+ADR V+9V V+60V V+5V
50 ADDRESS ASSY
RESONANCE BLOCK V+ADR V+9V V+60V
F
V+5V
DRIVER IC IC1551
DRIVER IC IC1552
DRIVER IC IC1553
DRIVER IC IC1554
DRIVER IC IC1555
DRIVER IC IC1551
DRIVER IC IC1552
DRIVER IC IC1553
DRIVER IC IC1554
DRIVER IC IC1555
22
1 2
PDP-504PU
3 4
A
DRIVER IC IC1551 DRIVER IC IC1552 DRIVER IC IC1553 DRIVER IC IC1554 DRIVER IC IC1555 DRIVER IC IC1551 DRIVER IC IC1552 DRIVER IC IC1553 DRIVER IC IC1554 DRIVER IC IC1555
V+5V V+3V_LVDS V+3V_PLL V+3V_IC5 IC1501 AD1 CN1501 V+9V V+60V V+ADR RESONANCE BLOCK
V+5V V+3V_LVDS V+3V_PLL V+3V_IC5 IC1501 AD1 CN1501 V+9V V+60V V+ADR RESONANCE BLOCK
50 ADDRESS ASSY
50 ADDRESS ASSY
S1 MAIN POWER AC INLET LIVE
P4 VSUS T105
NEUTRAL
50 X DRIVE ASSY
X2 VSUS RC101 DC_DC CONV BLOCK V_RN
T103
Switching Q119
X CONNECTOR B ASSY
CN1201
D133
MASK MOD IC1203 +5V Drive Signal +16.5V SUS OUT +5V
T104
M105 Switching
D131,D134
SECONDARY
PRIMARY
LOGIC BLOCK
RESONANCE BLOCK
+6.5V
P6
SUS OUT VSUS CN4001 R1 V+3V V+6.5V ACTV R4 DCLK, DE HD, VD TMDS RECEIVER RA IN, GA IN, BA IN RB IN, GB IN, BB IN IC4202 FET SW EEPROM for EDID STB3.3 MUTE Drive Signal +16.5V +5V
PANEL IF ASSY
R7 V+6.5V
PSUS
CN4009
X CONNECTOR A ASSY
+16.5V
CN4004
CN3503
R6 CN4007 LED_R,G
VOL IC IC3502
CN4010
Bus Buffer
STB _MT R2
R8
CN4751
KEY REM
L1
J3701
L,R
L,R
CN3701
B_SDA B_SCL
AUDIO L AUDIO R
SPEAKER
Bus Buffer
+9V
+16.5V
A3
SP2
SP1
E
CN4801 SW1
DVI CONNECTOR
MDR CONNECTOR
KL2
KL1
PANEL IR ASSY
RE1
50 ADDRESS ASSY
RESONANCE BLOCK V+ADR V+9V V+60V V+5V
50 ADDRESS ASSY
RESONANCE BLOCK V+ADR V+9V V+60V
DRIVER IC IC1551
DRIVER IC IC1552
DRIVER IC IC1553
DRIVER IC IC1554
DRIVER IC IC1555
DRIVER IC IC1551
DRIVER IC IC1552
DRIVER IC IC1553
DRIVER IC IC1554
DRIVER IC IC1555
PDP-504PU
5 6 7 8
23
Block Diagram
50 Y DRIVE ASSY
VH Y2
CN2101 Y1 CLK1 IC5V Photo Coupler Photo Coupler Photo Coupler CN2102 Y3 Photo Coupler Photo Coupler Photo Coupler Photo Coupler VH
To 50 SCAN B ASSY
To 50 SCAN A ASSY
CN2001
YPR-U YSOFT-D YSUS-G YSUS-B YSUS-U2 YSUS-D2 YSUS-U1 YSUS-D1 YSUS-MSK YOFS YSUS-PD SCN_5V_PD Y_DD_PD SCAN_PD YDRIVE_PD
YSUS-G YSUS-B YSUS IC2201 -U2 5V YSUS-D2 YSUS-U1 5V YSUS-D1 XSUS P.D. Circuit IC2202 HB DRIVER SUS GND HB DRIVER SUS GND L2204 L2205 Mask Module IC2307 STK795-513 L2202 L2203 Mask Module VSUS 5V 16.5V IC2303 STK795-513 To SCAN ASSY
VSUS 5V 16.5V
YSUS-MSK
IC2304
YOFS
IC2309
Y4
CN2301 16.5V 1 DGND 2 6.5V 3 DGND 4 N.C. 5 N.C. 6 VSUS 7 VSUS 8 N.C. 9 SUSGND 10 SUSGND 11 P.D. DET. IC2305 REGULATOR VSUS 5V
IC5V UVP
VOFS
VH D-D CONV.
VH
24
1 2
PDP-504PU
3 4
X1
50 X DRIVE ASSY
To X CONNECTOR ASSY XSUS-G XSUS-B XSUS IC1101 -U2 5V XSUS-D2 XSUS-U1 5V XSUS-D1 XSUS P.D. Circuit IC1102 HB DRIVER SUS GND HB DRIVER SUS GND L1104 L1105 Mask Module IC1207 STK795-512 L1102 L1103 Mask Module VSUS 5V 16.5V IC1203 STK795-512 PSUS
XSUS-G XSUS-B XSUS-U2 XSUS-D2 XSUS-U1 XSUS-D1 XSUS-MSK XCP-MSK XNR-D XSUS_PD XDD_PD XDRV_PD
CN1001
B
VSUS 5V 16.5V
XCP-MSK
VCP
XSUS-MSK
XNR P.D. DET. X2 CN1201 16.5V 1 DGND 2 6.5V 3 DGND 4 N.C. 5 N.C. 6 VSUS 7 VSUS 8 N.C. 9 SUSGND 10 SUSGND 11 N.C. 12 IC1204 P.D. DET. IC1205 REGULATOR VSUS VRN OVP P.D. VSUS D-D CONV. T1401 VRN-230V 5V XNR-D
PDP-504PU
5 6 7 8
25
Block Diagram
PANEL IF ASSY
R3 TMDS IC4202 TMDS RECEIVER IC4205 RESET IC Q4203 INV R4
DVI CONNECTOR
CN4003
11: MTXD IC4006 BUF 2: MRXD 3: P_ST_B IC4006 BUF 10: MR_ST_B IC4006 BUF 7: REQ IC4002 BACKUP ROM CN4004 R7 CN4009 R8 CN4010 REM KEY CN4007 LED G LED R R6 CN4006 OP DET R5
RXD0 TXD0 B_SCL, B_SDA MR_ST_B REQ_MD Q4004 INV MR_AC_OFF Q4006 INV CN4002 Q4006 INV IC4006 BUF KEY_B Q4006 INV Q4006 INV IC4006 BUF REM_B Q4009 INV
MDR CONNECTOR
LED_R_B LED_G_B A_NG,A_MUTE,STB_SW, FOCUS,TRUBASS,SRS A_SCL, A_SDA Q4001 5V 3.3V I2C LEVEL SHIFT
R_IN L_IN
26
1 2
PDP-504PU
3 4
Voltages
CN4001 (R1) < POWER SUPPLY UNIT >
No. Signal Name I/O
1 2 3 4 5 6 7 8 6.5V 6.5V Vcc_GND Vcc_GND STB3.3V STB_GND STB3.3MUTE AC_DET I I I O I
A
Signal Description
+6.5V power supply +6.5V power supply GND GND Power supply +3.3V input of module UCOM at panel side GND Standby control (+3.3V mute) Primary power supply (AC) state input at panel side
Signal Description
Connection state detecting signal with MDR
UART communication transmission data with the main UCOM (external PC) 0-3.3V amplitude square wave at MDR side
Connection state output for the MDR Power supply +3.3V output of module UCOM at panel side Primary power supply (AC) state output at panel side GND
Communication request to the main UCOM (external PC) at the MDR
0VDC +3.3VDC 0VDC 0-3.3V amplitude square wave +3.3VDC 0-3.3V amplitude square wave (at key operation) 0VDC 0-3.3V amplitude square wave Audio R signal 0-3.3V amplitude square wave (at remocon code transmission) 0VDC 0VDC Audio L signal
D
Standby power supply (+3.3V) input from the MDR Function key code signal output at panel side Connection state detecting signal with the MDR
UART communication receive data with the main UCOM (external PC) at the MDR side
10 MR_ST_B' 11 MTXD 12 GND 13 AUDIO_R 14 REM_B 15 16 17 18 19 20 STB_MT GND NC FIELD GND AUDIO_L
GND R ch audio signal input Remote control code signal output Standby control input GND Not connected FIELD control signal GND L ch audio signal input
Signal Description
DVI signal DVI signal GND Not connected Not connected I2C signal for DDC I2C signal for DDC Not connected DVI signal DVI signal GND Not connected Not connected I2C power supply for DDC GND Hot plug detection DVI signal DVI signal GND Not connected Not connected
PDP-504PU
5 6 7 8
27
Voltages
A
Signal Description
Signal Description
Rear panel open detecting signal Not connected GND
Signal Description
LED control (green) LED control (red) Primary power supply (AC) state output at the panel side
Signal Description
Abnormal detecting signal of the audio block +6.5V power supply GND L ch audio signal GND R ch audio signal Standby signal of the audio block Audio mute signal input I2C control signal for audio I2C control signal for audio Focus function control signal SRS function control signal TRUBASS function control signal
13 TRUBASS
D
Signal Description
+3.3V power supply GND Remote control code signal input +3.3V power supply Function key code signal input at the panel side GND
O I O I
Signal Description
28
1 2
PDP-504PU
3 4
Voltages
CN4004 (R4) < DIGITAL VIDEO ASSY > (1/2)
No. Signal Name I/O
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 GND GND
A
Signal Description
GND GND Not connected Not connected 8bit video signal output (BLUE even number) 8bit video signal output (BLUE even number) 8bit video signal output (BLUE even number) 8bit video signal output (BLUE even number) 8bit video signal output (BLUE even number) 8bit video signal output (BLUE even number) 8bit video signal output (BLUE even number) 8bit video signal output (BLUE even number) GND GND Not connected Not connected 8bit video signal output (GREEN even number) 8bit video signal output (GREEN even number) 8bit video signal output (GREEN even number) 8bit video signal output (GREEN even number) 8bit video signal output (GREEN even number) 8bit video signal output (GREEN even number) 8bit video signal output (GREEN even number) 8bit video signal output (GREEN even number) GND GND Not connected Not connected 8bit video signal output (RED even number) 8bit video signal output (RED even number) 8bit video signal output (RED even number) 8bit video signal output (RED even number) 8bit video signal output (RED even number) 8bit video signal output (RED even number) 8bit video signal output (RED even number) 8bit video signal output (RED even number) GND Synchronous signal output (clock) GND Synchronous signal output (data enable) Synchronous signal output (Horizontal sync.) Synchronous signal output (Vertical sync.) FIELD control signal Not connected Not connected Not connected 8bit video signal output (BLUE odd number) 8bit video signal output (BLUE odd number) 8bit video signal output (BLUE odd number) 8bit video signal output (BLUE odd number) 8bit video signal output (BLUE odd number) 8bit video signal output (BLUE odd number) 8bit video signal output (BLUE odd number) 8bit video signal output (BLUE odd number) GND GND Not connected Not connected
BA0 BA1 BA2 BA3 BA4 BA5 BA6 BA7 GND GND
O O O O O O O O
0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave
GA0 GA1 GA2 GA3 GA4 GA5 GA6 GA7 GND GND
O O O O O O O O
0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave
RA0 RA1 RA2 RA3 RA4 RA5 RA6 RA7 GND DCLK GND DEI HDI VDI FIELD APL_DT
O O O O O O O O O O O O O
0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave (42.5MHz)
0-3.3V amplitude square wave (positive polarity) 0-3.3V amplitude square wave (negative polarity) 0-3.3V amplitude square wave (negative polarity)
BB0 BB1 BB2 BB3 BB4 BB5 BB6 BB7 GND GND
O O O O O O O O
0V DC 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave
PDP-504PU
5 6 7 8
29
Voltages
A
Signal Description
8bit video signal output (GREEN odd number) 8bit video signal output (GREEN odd number) 8bit video signal output (GREEN odd number) 8bit video signal output (GREEN odd number) 8bit video signal output (GREEN odd number) 8bit video signal output (GREEN odd number) 8bit video signal output (GREEN odd number) 8bit video signal output (GREEN odd number) GND GND Not connected Not connected 8bit video signal output (RED odd number) 8bit video signal output (RED odd number) 8bit video signal output (RED odd number) 8bit video signal output (RED odd number) 8bit video signal output (RED odd number) 8bit video signal output (RED odd number) 8bit video signal output (RED odd number) 8bit video signal output (RED odd number) GND Not connected Not connected Not connected Not connected Power supply +3.3V output of module UCOM at panel side E2PROM control signal for backup
RB0 RB1 RB2 RB3 RB4 RB5 RB6 RB7 GND MASK MODE MODEL DITHER V+3VACTV B_SDA RXD0
O O O O O O O O
0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave 0-3.3V amplitude square wave
O I O O I O I I O I I O I O O I I I I I I I O I O O
90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114
REQ_MD LED_R_B MR_AC_OFF LED_G_B POWER DVI_MUTE MR_ST_B A_MUTE OP_DET A_NG PNL_MUTE A_SCL STB_SW A_SDA DDC_WP TRUBASS B_SCL FOCUS DVI_OFF SRS RSTBTMD MAX_PLS1 L_SYNC MAX_PLS2 GND
+3.3VDC 0-3.3V amplitude square wave UART communication receive data with the main UCOM (external PC) at MDR side 0-3.3V amplitude square wave 0-3.3V amplitude square wave (at remocon Remote control code signal output code transmission) UART communication transmission data with the main UCOM (external PC) at MDR side 0-3.3V amplitude square wave 0-3.3V amplitude square wave (at key Function key code signal output at panel side operation) Communication request to the main UCOM (external PC) at MDR side 0-3.3V amplitude square wave LED control (red) +3.3VDC AC state output at MR side 0VDC LED control (green) 0VDC Not connected DVI mute signal input 0VDC Connection state detecting signal with MDR 0VDC Audio mute signal input 0VDC Rear case open detecting signal 0VDC Abnormal detecting signal of audio block +3.3VDC Not connected I2C control signal for audio 0-3.3V amplitude square wave Standby signal of audio block +3.3VDC I2C control signal for audio 0-3.3V amplitude square wave EDID E2PROM writing inhibit signal 0VDC TRUBASS function control signal +3.3VDC E2PROM control signal for backup 0-3.3V amplitude square wave FOCUS function control signal +3.3VDC Connection detecting signal of DVI connector 0VDC SRS function control signal +3.3VDC TMDS IC reset signal +3.3VDC Not connected TMDS IC synchronous detecting signal +3.3VDC Not connected
30
1 2
PDP-504PU
3 4
A
Sync. signal 3-wire serial down 3-wires serial up
IC5
PANEL SIZE
OR
EMG
IC4
EMG
50 Y DRIVE ASSY
FLASH ROM
Sequence data
SCAN ASSY
THEATER
Xtal
RST
MANTA
OR
MUTE
For other HD
IC4_ RST
E_ SCL E_ SDA
C
VD_ IN
50 X DRIVE ASSY
Xtal
DVI_ MUTE
3STATE
W IC4 E_
MUTE
PD PD PD
For other HD
CST3
MODEL
OR
D
B_ SCL/ B_ SDA MRAC_ DET
MODULE UCOM
IC5201
PSW D _ MODE YDRV_ UC XDRV_ UC
DC- DC CONV.
For other HD
KEY REM
PD MUTE
Writing
For panel module
POW ER PNL_ MUTE DITHER MAX_ PLS1 MAX_ PLS2 MASK1 RESET CNVSS TXD1
OR
AND
3.3V RST IC
For other HD
STB_ SW SRS FOCUS TRUBASS VOFS VSUS A_ MUTE TEMP1
E
PANEL SENSOR ASSY
Thermal sensor
PD LED
F
DRIVE OFF
AC_ DET
Vsus
PDP-504PU
5 6 7 8
31
Voltages
A
CN5601 (D1)
No. Signal Name I/O
1 2 3 4 5 6 7 8 9 10 11 +12V +12V GND_D GND_D PD VSUS_ADJ PS_PD RELAY DRF AC_DET PD_TRIGGER I I O O I O O I I
Signal Description
+12V power input +12V power input GND GND Power down signal VSUS adjustment signal Power-down detecting signal of POWER SUPPLY block Relay control signal Drive control signal Primary side power (AC) state output at panel side Power down trigger
CN5602 (D2)
No. Signal Name I/O
1 2 3 4 5 6 7 VADR VADR N.C GND_ADR GND_ADR +6.5V GND_D I I I
Signal Description
Address drive power (+61V) input Address drive power (+61V) input Not connected GND GND +6.5V power input GND
+6.8VDC
32
1 2
PDP-504PU
3 4
CN3504
+16.5V
A2
A1 +6.5V WOW IC IC3501 R_Audio From PANEL IF ASSY L_Audio SCL, SDA SRS,FOCUS,TRUBASS +9.0V A_Mute ST-BY A_NG_B +16.5V REGULATOR IC3503 DC DETECT BLOCK POWER AMP IC IC3504 +16.5V BUFFER VOLUME IC IC3502
CN3501
R_OUT+
R_OUTL_OUT L_OUT +
CN3503
A3
J301
SP2
HD SP TERMINAL ASSY
R OUT
L OUT
SP1
PDP-504PU
5 6 7 8
33
3.2 WAVEFORMS
A
CH1
CH2
B
CH2
CH1
CH1
CH2
C
CH2
CH1
CH1
CH2
D
CH2
CH1
CH1
CH2
E
CH2
34
1 2
PDP-504PU
3 4
PANEL IF ASSY
1 CH1: K4005 (VDI)
CH2: K4006 (HDI) V: 2V/div. H: 5msec/div.
CH1
CH1
CH2
CH2
B
CH1
CH1
CH2
CH2
CH1
CH1
CH2
CH2
PDP-504PU
5 6 7 8
35
CH2 CH3
CH6 CH7
Reset Pulse
CH1: R1226 (XPSUS) - K1201 (SUSGND) (50 X DRIVE ASSY) CH2: R2348 (YPSUS) - K2301 (SUSGND) (50 Y DRIVE ASSY) CH3: K3001 (Scan OUT) - K2301 (SUSGND) (50 SCAN A ASSY) V: 100V/div. H: 100sec/div.
C
CH2
CH2: K1016 (XCP-MSK) - K1020 (DGND) CH3: K1015 (XSUS-MSK) - K1020 (DGND) CH4: K1014 (XNR-D) - K1020 (DGND)
V: 1V/div. H: 2msec/div.
CH1
CH2
CH2
CH3
CH3
CH4
Sustain Waveform
CH1: R2348 (YPSUS) - K2301 (SUSGND) (50 Y DRIVE ASSY) V: 50V/div. H: 500nsec/div.
CH2: K2015 (YSUS-MSK) - K2010 (DGND) CH3: K2017 (YSOFT-D) - K2010 (DGND) CH4: K2023 (YPR-U) - K2010 (DGND)
V: 1V/div. H: 2msec/div.
CH1
CH2 CH3
F
CH4
36
1 2
PDP-504PU
3 4
PDP-504PU
5 6 7 8
37
38
1 2
PDP-504PU
3 4
Mark No.
Description
Part No.
Mark No.
Description
Part No.
LIST OF ASSEMBLIES
NSP 1..50 ADDRESS ASSY NSP 2..50 ADDRESS ASSY NSP 1..50 SCAN FUKUGO ASSY NSP 2..50 SCAN A ASSY NSP 2..50 SCAN B ASSY NSP 2..X CONNECTOR A ASSY NSP 2..X CONNECTOR B ASSY NSP 1..HD FUKUGO ASSY 2..PANEL IF ASSY 2..PANEL LED ASSY 2..PANEL KEY ASSY 2..KEY CONTROL ASSY 2..PANEL IR ASSY 1..DIGITAL VIDEO ASSY NSP 1..HD AUDIO ASSY 2..HD SP TERMINAL ASSY 2..HD AUDIO AMP ASSY NSP 1..50 X DRIVE ASSY 2..50 X DRIVE ASSY 2..PANEL SENSOR ASSY 1..50 Y DRIVE ASSY
>
50 ADDRESS ASSY
AWV2069 AWZ6839 AWV2036 AWZ6809 AWZ6810 AWZ6811 AWZ6812 AWV2017 AWZ6786 AWZ6787 AWZ6788 AWZ6789 AWZ6790 AWV2070 AWV2019 AWZ6792 AWZ6834 AWV2034 AWZ6808 AWZ6795 AWV2035 AXY1068
CAPACITORS
C1553,C1556,C1559,C1560,C1563 (330p/100V) C1501,C1502 (47/6.3V) C1503-C1507,C1152,C1555 C1558,C1561,C1564 ACG1105 ACH1357 CKSSYF104Z16 CKSSYF104Z16
C
RESISTORS
R1510,R1519,R1522,R1526 R1505-R1509 R1513-R1518 Other Resistors RAB4C470J RS1/16SS1000F RS1/16SS470J RS1/16S###J
OTHERS
CN1501 40P FFC CONNECTOR AKM1215
D
CAPACITORS
C1609,C1615 (0.47/100V) C1605,C1607,C1608,C1613,C1614 (0.01/100V) C1601,C1602 (56/80V) C1618 (47/6.3V) C1603 (47/16V) C1604,C1606,C1612 ACE1171 ACG1101 ACH1405 ACH1357 ACH1391 CKSSYF104Z16
PDP-504PU
5 6 7 8
39
Description
Part No.
Mark No.
Description
Part No.
CCSRCH181J50 CCSRCH331J50 CCSRCH331J50 CCSRCH331J50 CCSRCH390J50 CCSRCH390J50 CCSRCH390J50 CKSRYB105K6R3 CKSRYB105K6R3
50 SCAN A ASSY
SEMICONDUCTORS
IC3001-IC3006 D3001
B
AN16003A-K KU10N16
RESISTORS
R3202,R3210,R3216,R3224,R3229 R3235 Other Resistors RAB4C221J RAB4C221J RS1/16S###J
CAPACITORS
C3001,C3002,C3012,C3013 (0.1/250V) C3023,C3024,C3034,C3035 (0.1/250V) C3045,C3046,C3056,C3057 (0.1/250V) C3005,C3008,C3016,C3019,C3026 C3029,C3037,C3040,C3048,C3051 C3060,C3063 C3004 C3007,C3018,C3033,C3044,C3050 ACG1088 ACG1088 ACG1088
OTHERS
CN3201 15P CONNECTOR K3203,K3208,K3214,K3216,K3218 TEST PIN K3220,K3221 TEST PIN AKP1218 AKX9002 AKX9002
CCSRCH101J50 CCSRCH101J50 CCSRCH101J50 CCSRCH151J50 CCSRCH181J50 CCSRCH181J50 CCSRCH331J50 CCSRCH331J50 CCSRCH331J50 CCSRCH390J50 CCSRCH390J50 CCSRCH390J50 CKSRYB105K6R3 CKSRYB105K6R3
X CONNECTOR A ASSY
This assembly has no service part.
X CONNECTOR B ASSY
This assembly has no service part.
PANEL IF ASSY
[PANEL IF BLOCK] SEMICONDUCTORS
IC4002
> IC4003
RESISTORS
D
24LC02B(I)SN PQ033EZ01ZP TC74VHC541FT DTA143EUA DTC143EUA DTC143EUA RN1901 RN2901 SM6K2 1SS355 RB751V-40 UDZS5.1B
OTHERS
CN3001 15P CONNECTOR K3001,K3004,K3009,K3015,K3017 TEST PIN K3019,K3021 TEST PIN AKP1218 AKX9002 AKX9002
50 SCAN B ASSY
E
SEMICONDUCTORS
IC3201-IC3206 D3201 AN16003A-K KU10N16
CAPACITORS
C3201,C3211,C3212,C3222,C3223 (0.1/250V) C3233,C3234,C3244,C3245 (0.1/250V) C3255,C3256,C3266 (0.1/250V) C3203,C3204,C3214,C3215,C3226 C3228,C3237,C3239,C3247,C3251 C3258,C3259 C3258,C3259 C3262 ACG1088 ACG1088 ACG1088
CAPACITORS
C4005,C4006 C4019 C4009,C4020 C4011,C4018,C4021 C4003,C4015 C4004,C4010,C4012,C4014 C4016,C4024,C4041 C4017 CCSRCH100D50 CCSRCH101J50 CCSRCH471J50 CEAT101M10 CEAT101M16 CKSRYB103K50 CKSSYF104Z16 CKSRYF105Z10
RESISTORS
PDP-504PU
3 4
40
1 2
Mark No.
R4006 Other Resistors
Description
Part No.
RAB4C101J RS1/16S###J
Mark No.
Description
Part No.
OTHERS
CN4004 114P FFC CONNECTOR CN4003 DVI SOCKET (24P) CN4002 SOCKET (20P) K4002-K4012 TEST PIN CN4006 3P TOP POST AKM1216 AKP1216 AKP1226 AKX9002 B3B-EH
OTHERS
CN4801 6P FFC CONNECTOR AKM1208
CAPACITORS
> C4856-C4858
C4854 C4853
RESISTORS
R4858 Other Resistors RAB4C182J RS1/16S###J
OTHERS
> X4851 CERALOCK
CAPACITORS
C4208,C4215,C4218,C4222,C4230 C4262 C4207,C4210,C4232,C4233,C4236 C4241,C4244,C4258 C4212,C4239,C4242,C4246 C4202,C4237,C4238 C4260 C4205,C4206,C4217,C4267 C4203,C4204,C4209,C4211,C4213 C4234,C4235,C4240,C4243,C4245 C4247,C4252,C4256,C4259,C4261 C4271 CCSRCH331J50 CCSRCH471J50 CCSRCH820J50 CCSRCH820J50 CEAT101M10 CEAT470M10 CKSRYB472K50 CKSRYF105Z10 CKSSYF104Z16 CKSSYF104Z16 CKSSYF104Z16 CKSSYF104Z16
ASS1162 VKN1596
PANEL IR ASSY
SEMICONDUCTORS
Q4901 D4902 D4901 2SC4116 1SS302 1SS355
CAPACITORS
C4901 C4903 C4902 C4904 CEVW470M6R3 CKSRYB102K50 CKSRYB103K50 CKSSYF104Z16
D
RESISTORS
R4241 R4213-R4218,R4245,R4247 R4253-R4255,R4257 R4250 Other Resistors RAB4C220J RAB4C470J RAB4C470J RS1/16S3900F RS1/16S###J
RESISTORS
Other Resistors RS1/16S###J
OTHERS
U4901 REMOTE RECEIVER UNIT RPM7240-H4
OTHERS
K4203,K4207 TEST PIN AKX9002
RESISTORS
R5101-R5115,R5131 Other Resistors RAB4C470J RS1/16S###J
CAPACITORS
> C4751-C4753
CCSRCH101J50
OTHERS
CN5001 114P FFC CONNECTOR K5002-K5004,K5007 TEST PIN CN5002 10P CONNECTOR AKM1216 AKX9002 B10B-PH-SM3
OTHERS
CN4751 CONNECTOR 3P B3B-ZR-3.4
PDP-504PU
5 6 7 8
41
Part No.
Description
Part No.
AKM1232 AKX9002 ASS1174 ASS1176
IC5206 IC5201 IC5205 IC5208 IC5213 IC5214,IC5215 IC5211,IC5212 IC5209 Q5201 D5207-D5212
24LC04B(I)SN M30626FHPGP-P PST3628UR TC74VHC08FT TC74VHC123AFT TC74VHC32FT TC74VHC541FT TC7W126FU 2SJ461A 1SS301 1SS355 SML-310LT
CN5301 PLUG 15-P K5301 TEST PIN > X5302 CRYSTAL OSCILLATOR > X5301 CRYSTAL OSCILLATOR
D5217,D5218 D5201
CAPACITORS
C5401,C5413,C5417,C5424 (100/6.3V) C5434,C5435 C5402-C5412,C5414-C5416 C5418-C5423,C5425-C5431 ACH1396 CKSRYB102K50 CKSSYF104Z16 CKSSYF104Z16
CAPACITORS
C5213,C5225 (47/6.3V) C5206,C5223,C5231 C5245-C5264 C5232 C5230 C5205
C
RESISTORS
R5406,R5421 R5408-R5413,R5415,R5416,R5419 R5422 R5405 Other Resistors RAB4C101J RAB4C220J RAB4C220J RS1/16S5601F RS1/16S###J
OTHERS
K5401 TEST PIN AKX9002
RESISTORS
R5209,R5211,R5212,R5235 R5254,R5255,R5265,R5266 R5205 R5270,R5271 R5256,R5257 Other Resistors
D
OTHERS
CN5201 PLUG 8-P K5201 TEST PIN > X5201 CERAMIC RESONATOR CN5202 3P PH CONNECTOR AKM1225 AKX9002 ASS1178 B3B-PH-SM3
OTHERS
CN5521 50P CONNECTOR
> CN5501-CN5508 40P CONNECTOR
CAPACITORS
C5320 C5304,C5307 C5311,C5314 C5303,C5306 C5301,C5302,C5305,C5309,C5313 C5316
F
CAPACITORS
C5601,C5603,C5607,C5614,C5616 (100/16V) C5602,C5604,C5615,C5617 C5605,C5606,C5610 ACH1394 CKSRYB103K50 CKSSYF104Z16
RESISTORS
R5601 (1,1/2W) R5627 (3.3,1/2W) Other Resistors ACN1162 ACN1168 RS1/16S###J
RESISTORS
R5317,R5318 Other Resistors RAB4C101J RS1/16S###J
42
1 2
PDP-504PU
3 4
Description
Part No.
B11B-PH-SM3 B7B-PH-SM3
Description
Part No.
RD1/2MMF2R2J RS1/16S###J
OTHERS
HD SP TERMINAL ASSY
COILS AND FILTERS
L3701,L3702 ATF1206
3511 AUDIO HEATSINK ANH1612 CN3504 3P CONNECTOR B3P-VH 3512-3515 SCREW VBB30P100FNI KN3501,KN3502 WRAPPING TERMINALVNF1084
CAPACITORS
> C3701-C3704
50 X DRIVE ASSY
[50 X LOGIC BLOCK] SEMICONDUCTORS
IC1002 IC1001 IC1003 TC74ACT540FT TC74ACT541FT TC74VHC08FT
B
RESISTORS
R3701-R3704 RD1/2MMF100J
OTHERS
J3701 6P HOUSING WIRE CN3701 SPEAKER TERMINAL > 3701 SPEAKER SHIELD A > 3702 SPEAKER SHIELD B ADX2838 AKE1060 ANK1710 ANK1711
CAPACITORS
C1001 C1002-C1004 CEHAT470M25 CKSRYB104K16
RESISTORS
R1001,R1002,R1005 R1003,R1004,R1007 RAB4C470J RAB4C472J
C
OTHERS
CN1001 30P FFC CONNECTOR AKM1218
CAPACITORS
C3525 C3501-C3504,C3520,C3528-C3532 C3505,C3526,C3549,C3557,C3564 C3519 C3536 C3537,C3538 C3551,C3552 C3566 C3561 C3562,C3565 C3559,C3560 C3509 C3507 C3571 C3563 C3512,C3522,C3572 C3511,C3513-C3518,C3533,C3534 C3545-C3548,C3573-C3576 C3521 C3524 C3523 C3506,C3508,C3510,C3527,C3535 C3550,C3558 C3543,C3544 CCSRCH221J50 CEAT100M50 CEAT101M16 CEAT1R0M50 CEAT220M50 CEAT2R2M50 CEAT330M25 CEHAT101M10 CEHAT101M16 CEHAT220M50 CEHAT2R2M50 CEHAT331M16 CEHAT471M25 CEHAT472M25 CEHATR47M50 CFTLA103J50 CFTLA104J50 CFTLA104J50 CFTLA333J50 CFTLA334J50 CFTLA474J50 CKSRYB103K50 CKSRYB103K50 CQMA222J50 CPH5506 1SS133 1SS302 EC11FS4 EC11FS4 EC11FS4 FCU20A30 FCU20A30 UDZS16B
CAPACITORS
C1112,C1113,C1114,C1125,C1126 (3.3/250V) C1127 (3.3/250V) C1111,C1124 (100p/630V) C1109,C1119 (0.1/630V) C1101,C1105,C1116,C1117 C1128,C1130-C1132 C1102,C1118 C1104,C1108,C1115,C1122 ACE1168 ACE1168 ACG1104 ACG1108 CCSRCH331J50 CKSRYB104K16 CKSRYB105K6R3 CKSYB105K25
F
PDP-504PU
5 6 7 8
43
Description
Part No.
RD1/4PU390J RS1/10S1003F RS1/10S100J RS1/10S2R2J RS1/10S2R2J RS1/16S1202F RS1/16S3301F RS1/16S5601F RS1/16S8201F RS1MMF101J CCP1390 RS1/16S###J
Mark No.
R1235,R1236 Other Resistors
Description
Part No.
RS2MMF121J RS1/16S###J
R1154 R1116,R1122 R1133,R1143-R1145 R1103,R1106,R1110,R1111,R1118 R1119,R1153,R1123,R1126 R1136 R1139 R1130 R1134 R1113,R1128 VR1101-VR1104 Other Resistors
OTHERS
KN1201-KN1205,KN1208,KN1209 (GROUND PLATE) KN1210-KN1212,KN1213,KN1214 (GROUND PLATE) CN1201 12P CONNECTOR ANK-142 ANK-142 B12B-EH
HCPL-M611 NJM2872F05 STK795-512 TLP181(P-GR) TND301S 2SC2412K 2SD1898 2SJ522 2SK2503 2SK3116-Z DTC124EK HN1B04FU 1SS302 1SS355 EC10QS04 EC11FS4 EC8FS6 UDZS5.6B
CAPACITORS
C1401,C1402 (22/315V) C1404 C1405 C1409 C1403,C1407,C1408,C1411 C1406 ACH1361 CEHAT101M16 CEHAT101M25 CEHAT331M16 CKSRYB104K16 CKSRYF104Z50
RESISTORS
R1405,R1406,R1408-R1410,R1414 R1420 R1403 R1401,R1404 R1417 VR1401 (1k) Other Resistors RS1/10S3602F RS1/16S1101F RS1/16S2702F RS1/16S4701F RS1/16S7500F CCP1390 RS1/16S###J
CAPACITORS
C1214-C1217,C1227-C1230 C1233 (0.12/250V) C1244 (0.1/250V) C1209 (0.1/630V) C1219,C1231
E
ACE1163 ACE1169 ACE1170 ACG1092 ACH1358 CEHAT101M16 CEHAT221M25 CEHAT470M25 CEHAT470M25 CKSRYB102K50 CKSRYB104K16 CKSRYF104Z50
OTHERS
1002 1001 1001 1001 1001 CARD SPACER DRIVE SIRICON SHEET A PLATE X DRIVE HEATSINK A SCREW AEC1957 AEH1062 ANG2622 ANH1613 BMZ30P080FZK PMB30P060FNI
1002 SCREW
RESISTORS
R1230 (2.2, 1/2W) R1208,R1321,R1322 (10,1/2W) R1304 (560,1/2W) R1305 (1k,1/2W) R1301,R1302,R1314 R1226,R1251 ACN1166 ACN1174 ACN1195 ACN1198 RS1/10S122J RS1MMF331J
CAPACITORS
C1075 (47/6.3V) C1074 C1071,C1076 C1072,C1073 ACH1357 CKSRYB103K50 CKSRYB104K16 CKSRYF105Z10
44
1 2
PDP-504PU
3 4
Description
Part No.
RS1/16S1001F RS1/16S###J
Part No.
ACE1168
A
50 Y DRIVE ASSY
OTHERS
2002 2001 2001 2001 2001 CARD SPACER DRIVE SIRICON SHEET A PLATE Y DRIVE HEATSINK A SCREW AEC1957 AEH1062 ANG2557 ANH1613 BMZ30P080FZK PMB30P060FNI
RESISTORS
R2254 R2240,R2241 R2244-R2247 R2204,R2205,R2211,R2213,R2220 R2221,R2224,R2228,R2253 R2234 R2235 R2233 R2242 R2215,R2230 VR2201-VR2204 (1k) Other Resistors RS1/4PU390J RS1/10S1003F RS1/10S100J RS1/10S2R2J RS1/10S2R2J RS1/16S1202F RS1/16S3301F RS1/16S5601F RS1/16S8201F RS1MMF101J CCP1390 RS1/16S###J
C B
2002 SCREW
CAPACITORS
C2001 C2010,C2011 C2002-C2006 CEHAT470M16 CKSRYB104K16 CKSRYF104Z50
RESISTORS
R2018,R2019 R2002,R2004,R2013-R2015 R2005,R2006,R2012,R2016,R2017 Other Resistors RAB4C102J RAB4C470J RAB4C472J RS1/16S###J
OTHERS
CN2001 50P CONNECTOR AKM1201
CAPACITORS
C2309-C2312,C2326,C2327 (1.5/300V) C2329,C2330 (1.5/300V) C2314 (0.047/250V) C2302 (0.1/630V) C2316,C2331 (300/280V) C2303 (22/315V) C2336 (220/100V) C2306,C2334 C2308,C2324,C2339,C2340 C2304,C2320,C2338 C2305,C2322,C2323,C2325,C2333 ACE1163 ACE1163 ACE1165 ACG1092 ACH1358 ACH1361 ACH1393 CEHAT221M25 CEHAT470M16 CEHAT470M25 CKSRYB104K16
PDP-504PU
5 6 7 8
45
Mark No.
Description
Part No.
CKSRYB104K16 CKSRYF104Z50
Mark No.
D2403,D2414 D2402 D2427 D2401
Description
Part No.
EC11FS4 EC8FS6 RD91PA U1ZB330 UDZS15B UDZS27B UDZS33B UDZS4.3B UDZS5.6B
C2341 C2301,C2307,C2328
A
RESISTORS
R2332 (2.2,1/2W) R2364,R2365 (10,1/2W) R2309 R2310,R2311 R2312-R2314,R2322,R2323 R2348,R2352,R2358,R2359 Other Resistors ACN1166 ACN1174 RS1MMF132J RS1MMF472J RS3LMF100J RS3LMF1R8J RS1/16S###J
OTHERS
B
CAPACITORS
C2406 (100/160V) C2401 (22/315V) C2427 C2403 C2405,C2407,C2417 HCPL-M611 HCPL-M611 TC74ACT540FT C2414 C2410 C2411 C2420 C2409,C2419 C2402,C2412,C2413,C2423,C2425 C2431,C2432,C2434-C2436 C2441-C2443 C2415,C2421,C2428 C2404,C2408,C2416,C2418,C2426 C2429
D
ACH1360 ACH1361 CEHAT100M50 CEHAT101M16 CEHAT101M25 CEHAT221M16 CEHAT221M25 CEHAT331M25 CEHAT470M2A CKSRYB103K50 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB105K6R3 CKSRYF104Z50 CKSRYF104Z50
CAPACITORS
C2104,C2111,C2116,C2117 (47/160V) ACH1392 C2101,C2107,C2113 CEHAT221M16 C2102,C2103,C2105,C2106 CKSRYB104K16 C2108-C2110,C2112,C2114 CKSRYB104K16
RESISTORS
R2121,R2128 Other Resistors RAB4C472J RS1/16S###J
RESISTORS
R2429 (180k,1/2W) R2435,R2439 R2402-R2404 R2442 R2468 R2424 R2420,R2427,R2438 R2467 R2457-R2460 R2506 VR2401,VR2402 (1k) Other Resistors ACN1225 RS1/10S2202F RS1/10S3902F RS1/16S1201F RS1/16S1202F RS1/16S2001F RS1/16S2201F RS1/16S3301F RS1/16S4701F RS3LMF151J CCP1390 RS1/16S###J
OTHERS
CN2101,CN2102 15P CONNECTOR AKM1200
IC2410-IC2412 IC2406 IC2401 IC2402-IC2405,IC2407-IC2409 Q2402,Q2407 Q2410 Q2417 Q2411-Q2414,Q2416 Q2405 Q2403 Q2401,Q2404 Q2415 D2430 D2410,D2419,D2436 D2409,D2418 D2404-D2407
AN1431M BA10358F MIP0223SC TLP181(P-GR) 2SA1037K 2SA1163 2SA1535 2SC2412K 2SC2713 2SD1664 2SD1898 HN1C01FU 1SS301 1SS302 1SS355 EC11FS2
OTHERS
2401 HEATSINK 2401 SCREW ANH1614 BBZ30P080FZK
46
1 2
PDP-504PU
3 4
6. ADJUSTMENT
6.1 ADJUSTMENT REQUIRED WHEN THE SET IS REPAIRED OR REPLACED
50 X DRIVE Assy
When replaced VRN Voltage adjustment.
A
50 Y DRIVE Assy
When replaced No adjustment is required, because necessary adjustment has already been made.
PANEL IF Assy
When replaced Replace the IC4201 from old assemble to new one.
6.2 COMMAND
6.2.1 RS232C COMMAND
The panel control items for the PDP-504 system can be controlled with the RS-232C commands by connecting a PC through the GGF1475 special communication device when the Media Receiver is not connected with the PDP.
Note: The special communication device for the PDP-503P cannot be used with this unit, because the control lines within the MDR cable are different.
Connection
MDR
Communication line: Connect the system cable. GGF1475 special communication device PC for control Connect to the D-SUB 9-pin connector. D-SUB 9-pin straight cable
PDP-504PU
5 6 7 8
47
48
1 2
PDP-504PU
3 4
Validity of direct numeric input Validity Lower limit Upper limit 0000 255 ?
? ?
98 121
158 135
Window (for measuring the peak luminance, Hi = 1023, 4%) Window (for measuring the peak luminance, Hi = 1023, 1.25%) Window (vertical line with 1/7-width for measuring the stress) Window (magenta, green, and stripe for check) Window (green,magenta, and stripe for checker) Window (black & white [1 x 8], checker, for EMG check) Window (for WB adjustment, magenta = 512, yellow = 512) Wiper for erasing afterimage Mask for warning of cable disconnection ColorBar Slanted lines (for checking cable disconnection) Raster-white Raster-red Raster-green Raster-blue Raster-black Raster-cyan 1023 Raster-magenta 1023 Raster-yellow 1023 Raster-cyan 274 Raster-flesh color_50 Raster-light purple_50 Raster-sky blue_50 Raster-red 779 Raster-cyan 218 Raster-cyan 448
PDP-504PU
5 6 7 8
49
A
66 67 68 69 70 71 72 73 74 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 M66 M67 M68 M69 M70 M71 M72 M73 M74 PBH PBL PCN PCY PGH PGL PLA PLB PLN POF PON PRH PRL SCN SCY SRN SRY TBN TBY TRE TSN TSY UAJ VOF VOL VSU XD1 XD2 XU1 XU2 YD1 YD2 YD3 YD4 YU1 YU2
Command Name MASK MODE 66 MASK MODE 67 MASK MODE 68 MASK MODE 69 MASK MODE 70 MASK MODE 71 MASK MODE 72 MASK MODE 73 MASK MODE 74 PANEL BLUE HIGH PANEL BLUE LOW PC RGB NO PC RGB YES PANEL GREEN HIGH PANEL GREEN LOW BRIGHT ENHANCE A BRIGHT ENHANCE B BRIGHT ENHANCE NO POWER OFF POWER ON PANEL RED HIGH PANEL RED LOW SYSTEM CABLE NO SYSTEM CABLE YES SRS NO SRS YES TRUBASS NO TRUBASS YES TREBLE ADJUSTMENT TRAP SW NO TRAP SW YES UN-ADJUSTMENT Vofs ADJUSTMENT VOLUME Vsus ADJUSTMENT XSUS-D-1 XSUS-D-2 XSUS-U-1 XSUS-U-2 YSUS-D1-1 YSUS-D1-2 YSUS-D2-1 YSUS-D2-2 YSUS-U-1 YSUS-U-2 Raster-flesh color_43 Raster-red 640 Raster-magenta 98 Raster-sky blue 1_43 Raster-sky blue 2_43 Raster-light purple_43 Raster-blue 60 Raster-gray 512 (reservation) Raster-gray 512 (reservation)
Function
Panel white-balance adjustment: Blue highlight Panel white-balance adjustment: Blue low light Setting input-signal type to video Setting input-signal type to PC Panel white-balance adjustment: Green highlight Panel white-balance adjustment: Green low light
Center luminance-compensation function on (no correspondence with APL) Center luminance-compensation function on (in correspondence with APL)
? ?
000 000
511 999
? ?
000 000
511 999
Center luminance-compensation function off Power off Power on Panel white balance adjustment-red highlight Panel white-balance adjustment: Red low light Prohibiting monitoring of cable-disconnection detection Permitting monitoring of cable-disconnection detection SRS function off SRS function on TruBass function off TruBass function on Audio treble adjustment Prohibiting detection of opening of the rear case Permitting detection of opening of the rear case Z-number 0003 to F003 Vofs voltage reference-value adjustment Audio volume adjustment Vsus voltage reference-value adjustment XSUS-D-1 adjustment XSUS-D-2 adjustment XSUS-U-1 adjustment XSUS-U-2 adjustment YSUS-D1-1 adjustment YSUS-D1-2 adjustment YSUS-D2-1 adjustment YSUS-D2-2 adjustment YSUS-U-1 adjustment YSUS-U-2 adjustment
? ?
000 000
511 999
121
135
? ? ? ? ? ? ? ? ? ? ? ? ?
000 000 000 000 000 000 000 000 000 000 000 000 000
255 060 255 255 255 255 255 255 255 255 255 255 255
50
1 2
PDP-504PU
3 4
Command description
Command GAJ GPD GPW GS1 GS2 GSD Function Obtaining various adjustment values Obtaining power-down-point log Obtaining panel white-balance adjustment values Obtaining information on the unit, such as the software version Obtaining information on the status of the unit Obtaining information on shutdown Data Size 3 bytes 3 bytes 3 bytes 3 bytes 3 bytes 3 bytes 3 bytes 3 bytes 3 bytes 3 bytes 3 bytes 3 bytes 3 bytes 3 bytes Remarks AB1 - AB3 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255 000 - 255
A
GAJ: Obtaining data on ABL setting values, electronic-control adjustment values, and drive-system adjustment values
Order 1 ABL table currently used 2 Upper limit of power 3 Vsus adjustment value 4 Vofs adjustment value 5 X-SUS-U1 adjustment value (XU1) 6 X-SUS-U2 adjustment value (XU2) 7 X-SUS-D2 adjustment value (XD2) 8 X-SUS-D1 adjustment value (XD1) 9 Y-SUS-U1 adjustment value (YU1) 10 Y-SUS-U2 adjustment value (YU2) 11 Y-SUS-D1-2 adjustment value (YD2) 12 Y-SUS-D1-1 adjustment value (YD1) 13 Y-SUS-D2-2 adjustment value (YD4) 14 Y-SUS-D2-1 adjustment value (YD3) Note: Ignore the 2-byte checksum at the end. Order 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 31 Notes: Data
PDP-504PU
5 6 7 8
51
Description on power-down
Data Power-down Point
0 1 2 3 4 5 6 7 8 9 A B C D E F
No power-down Not used (for MR-POWER) Panel-POWER SUPPLY SCAN SCN-5V Y-DRIVE Y-DCDC Y-SUS ADR X-DRIVE X-DCDC X-SUS DIG-DCDC Reservation Reservation Power-down point unidentified
GS1: Obtaining information on the unit, such as the software version (1)
Order 1 2 3 4 5 6 7 8 9 10 11 12 Data Display data Version of the module microcomputer IC4-MANTA version Sequence version (43VIDEO) Sequence version (43PC) Sequence version (50VIDEO) Sequence version (50PC) Version of the IF microcomputer Version of the main microcomputer IC3-MANTA version Version of the OSD Reserve Size 3 bytes 4 bytes 4 bytes 4 bytes 4 bytes 4 bytes 4 bytes 4 bytes 4 bytes 4 bytes 4 bytes 12 bytes
IC4 communication failure EEPROM communication failure Audio failure Volume IC communication failure Backup ROM communication failure Data on temperature (TEMP1) not obtained Operational status of panel protection mechanism Reservation 1st-5th byte: Hour, 6th-7th byte: Minute Hour meter Ignore the 2-byte checksum at the end. The data expected to be used for service may be "5. Data on temperature" and "15. Hour meter".
Size 1 byte 1 byte 1 byte 2 bytes 3 bytes 1 byte 1 byte 1 byte 1 byte 1 byte 1 byte 1 byte 1 byte 9 bytes 7 bytes
Remarks 1: OK for shifting to Standby 0: Adjusted, 1: Not adjusted 0: With backup, 1: Without backup 1st byte: 1stPD, 2nd byte: 2ndPD
0: Normal, 1: SD process completed, 2: In the process of SD warning 0: Normal, 1: SD process completed, 2: In the process of SD warning 0: Normal, 1: SD process completed, 2: In the process of SD warning 0: Normal, 1: SD process completed, 2: In the process of SD warning 0: Normal, 1: SD process completed, 2: In the process of SD warning 0: Normal, 1: SD process completed, 2: In the process of SD warning 0: Normal, 1: SD process completed, 2: In the process of SD warning 0: Normal, 1: SD process completed, 2: In the process of SD warning 0: Protection mechanism not activated, 1: Protection mechanism activated
52
1 2
PDP-504PU
3 4
Description of shutdown
Data
Factors of shutdown No abnormality IC4 Module microcomputer IIC Abnormality in RST2 (power decrease of DC-DC converter) Panel having high temperature Audio failure (speakers short-circuited) Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 1 2 3 4 5 6 7 8 9 A B C D E F
Factors of shutdown No subcategory EEPROM (DIGITAL VIDEO Assy : IC5206) EEPROM (PANEL IF Assy : IC4002) Volume IC Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation Reservation
PDP-504PU
5 6 7 8
53
7. GENERAL INFORMATION
7.1 DIAGNOSIS
A
50 ADDRESS Assy
X CONNECTOR B Assy
50 SCAN B Assy
X CONNECTOR A Assy
Rear view
54
1 2
PDP-504PU
3 4
MR-LED
Standby RED GREEN RED GREEN
PANEL-LED
Power on
Normal MR-AC power off RED GREEN RED GREEN RED GREEN RED GREEN RED GREEN RED GREEN RED GREEN RED GREEN RED GREEN
1.0S 1.0S 1.0S 1.0S 0.5S 0.5S 0.5S 3.0S 1.0S 1.0S 1.0S 1.0S
MR power-down
0.5S
3.0S
MR shutdown
0.5S
0.5S
0.5S
3.0S
Abnormality in MR
MR modification
P-power-down
P-shutdown
0.5S
0.5S
0.5S
3.0S
Disconnection of cable
Power management when the Media Receiver is not connected with the PDP
RED GREEN
1.0S
1.0S
PDP-504PU
5 6 7 8
55
Identification of locations having abnormality by the number of times the LEDs flash
On Shutdown and power-down
A
Shutdown Operation: When the microcomputer detects any abnormality, it forcibly turns off the unit. LED indication: The green LED flashes. Power-down Operation: When the unit is in emergency status, a protection circuit is activated, and the power is turned off. LED indication: The red LED flashes.
Category
MR-LED STB ON
Lit
PANEL-LED STB ON
1 time
2 times 3 times
Content
Unit's operation
Communication failure of the Immediate shutdown panel-drive IC Communication failure of the Immediate shutdown module IIC Power decrease of the digital Immediate shutdown DC-DC converter Shutdown 30 seconds after warning Powering off. Internal temperature too high. Check temperature around PDP. Check temperature around media receiver. [SD04] Powering off. Internal protection circuits activated, Is there a short in speaker cable ? [SD05]
Lit Lit
Lit
Lit
C
6 times
Communication failure of the Immediate shutdown module microcomputer Main 3-wire serial communication in failure Immediate shutdown
SD
Communication failure of the Immediate shutdown main IIC Communication failure of the Immediate shutdown main microcomputer Fan in failure MR or unit having higher temperature Immediate shutdown Shutdown 30 seconds after warning Powering off. Internal temperature too high. Check temperature around PDP. Check temperature around media receiver. [SD11]
11 times
Lit
Communication failure of the Immediate shutdown digital tuner MR-ASIC power (DC-DC) in failure Communication failure of IF-EEPROM MR power supply Panel-POWER SUPPLY SCAN SCAN-5V Y-DRIVE Y-DCDC Y-SUS ADDRESS X-DRIVE X-DCDC X-SUS DIGITAL-DCDC UNKNOWN Immediate shutdown Immediate shutdown Immediate power-down Immediate power-down Immediate power-down Immediate power-down Immediate power-down Immediate power-down Immediate power-down Immediate power-down Immediate power-down Immediate power-down Immediate power-down Immediate power-down Immediate power-down
PD
1 time Lit Lit Lit Lit Lit Lit Lit Lit Lit Lit Lit Lit
If the unit cannot identify which protection circuit was activated, even if a power-down had been detected, the red LED may flash 15 times.
56
1 2
PDP-504PU
3 4
PANEL IF ASSY
R7
RST2
2 2
IC4002 EEPROM IC5201 MODULE UCOM E_SCL E_SDA
IC5206 EEPROM
B
D4 TE1
IC3502 VOLUME IC
4
TEMP1
A_SCL A_SDA
B_SCL B_SDA
Diagnosis of shutdown
LED SD Circuit in Operation Defective Assy Reason for Shutdown Communication failure of IC4 Communication 1 time failure of the panel-drive IC DIGITAL VIDEO Writing failure of IC4 Point to be Checked IC4 BLOCK, PANEL FLASH BLOCK Possible Defective Part IC5401, IC5305
C
Remarks
After turning the unit on again, check if the data on the version can be read with the GS1 command. MODULE UCOM BLOCK PANEL IF BLOCK IC5206 IC4002 Check if the cable is disconnected or not securely connected. IC3502 ADY1081 Check if the 114-pin FPC is broken or not securely connected. Check if 3.3 V, 2.5 V, and 1.5 V are activated.
DIGITAL VIDEO Communication failure of the PANEL IF module IIC 2 times (Check the shutdown subcategory on the Factory menu.) HD AUDIO
Communication failure of the EEPROM (4K) Communication failure of the EEPROM (2K)
3 times
POWER SUPPLY No startup of 12 V Cable disconnected Panel having DIGITAL VIDEO higher temperature
CN5202 - CN1071 Shutdown occurs when the sensor temperature becomes 77C or more (PDP434P) or 83C or more (PDP-504P). Check if the speaker cables are in contact with the chassis, etc. IC3504 Check if the cable is disconnected or not securely connected.
E
4 times
Surrounding temperature
Speaker short-circuited Speaker terminals 5 times Audio failure HD AUDIO HD AUDIO Defective AMP IC HD AUDIO AMP ASSY
PDP-504PU
5 6 7 8
57
58
Note: The figures 1 - = indicate the number of times the LED flashes on the panel when power-down occurs in the corresponding route.
ADR_ PD
D5 -D8
AD1
D9 -D12
IC5214 IC5215 OR
2
XDRIVE_ PD XDD_ CNV_ PD XSUS_ PD
X DRIVE ASSY
S5201 D1 OR
PD_ MUTE
D14
IC5208 PD-MUTE circuit
PDP-504PU
X1
9 0 -
P2
Relay control
Y DRIVE ASSY
SCAN_ PD 5V_ YDRIVE_ PD YDD_ CNV_ PD YSUS_ PD
D13
SCAN_ PD
Y1 2
3 4 5 6 7
=
DCC_ PD
Protection circuit
DC-DC converter
PD_ TRIGGER
PD Circuit in operation Reason for Power-down Point to be Checked Possible Defective Part Remarks
Defective Assy
MR POWER
5
VSUS UVP VSUS UVP VH UVP VH UVP Disconnection of cable detected Disconnection of cable detected IC5V UVP IC5V OVP +16.5V OCP VOFS UVP VOFS OVP VH OVP Power-down caused by detection of middle-point voltage Y RESONANCE BLOCK Power-down caused by detection of middle-point voltage DIGITAL VIDEO Assy CN1501 ADR RESONANCE BLOCK ADR RESONANCE BLOCK CN1001, CN1201 X SUS BLOCK X SUS BLOCK VRN DC/DC VRN DC/DC VRN UVP X SUS BLOCK X RESONANCE BLOCK Q1205, R1226, R1251 IC1203, IC1207 (mask module), IC1204, IC1206, R1230 Q1205, R1226, R1251 IC1403, IC1404 IC1402, IC1403, IC1404 R1631, Q1601, D1602 Disconnection of cable detected Power-down caused by detection of a power surge Power-down caused by detection of middle-point voltage Disconnection of cable detected +16.5V OCP VRN OCP VRN OVP VH DC/DC IC2402, IC2410 Q2202, Q2214, Q2205, Q2206, Q2208, Q2209, Q2211, Q2212, IC2201, IC2202, Control signal series resistors IC5401, Control signal series resistors VOFS DC/DC IC2404, IC2412 VOFS DC/DC Y SUS BLOCK IC5V DC/DC IC2403, IC2411 IC2303 - IC2307 (mask module), IC2301, IC2304, R2309 IC2404, IC2412, Q2404, Q2407 SCAN IC, IC5V DC/DC Y SUS BLOCK SCAN IC, Q2401, Q2402, IC2304, IC2309 CN2101, CN2102 CN2001, CN2301 VH DC/DC IC2401, IC2402, IC2410, L2401 SCAN IC SCAN IC Y SUS BLOCK IC2303 - IC2307 (mask module) X SUS BLOCK IC1203 - IC1207 (mask module) Q1602, C1609, D1606, D1607 Power-down caused by detection of middle-point voltage Power-down caused by detection of middle-point voltage DCDC +3.3V, +1.5V OVP Q1102, Q1103, Q1105, Q1106, Q1108, Q1109, Q1111, Q1112, IC1101, IC1102, Control signal series resistors DIGITAL VIDEO Assy DC DC CONVERTER BLOCK IC5401, Control signal series resistors U5601 (DC DC CONVERTER Module)
POWER
If the elapsed time from relay-on until the LED in the power supply unit lights is about 2-4 seconds, the defective assembly may be the 50 X or Y DRIVE.
50 X DRIVE Assy
50 Y DRIVE Assy
SCAN
SCN-5V
6 E D C
Y-DRIVE
50 Y DRIVE Assy
Y-DCDC
50 Y DRIVE Assy
50 Y DRIVE Assy
PDP-504PU
Y-SUS
ADRS
50 ADDRESS Assy
X-DRIVE
50 X DRIVE Assy
10 X-DCDC
50 X DRIVE Assy
50 X DRIVE Assy
11 X-SUS
12 DIG-DCDC
OVP : Over Voltage Protection UVP : Under Voltage Protection OCP : Over Current Protection
59
When the Media Receiver is connected, the power-down and shutdown logs can be referred to with OSD. Only the items useful when servicing the PDP-434PU/PDP-504PU are described here.
I N1 0 1 3 NTV ST 1
S ECOND Y DCDC 0 0 0 0 0 0 0 0 0 0 0 0 5 2 0 0 0 0 2 7 9 4 0 0 3 5 0 3 2 0 H H H H H H H H 5 4 5 0 3 0 1 2 0 3 1 7 M M M M M M M M
10
C
15 16
I N F ORM A T I ON
I N1 0 1 3 NTV ST 1
D
5
SUB VOL I C 0 0 0 0 0 0 0 0 1 0 0 0 0 7 5 5 3 5 0 0 H H H H H H H H 5 4 5 4 1 2 0 5 M M M M M M M M
10
15 16
60
1 2
PDP-504PU
3 4
I N F ORM A T I ON TEMPERATURE
5
I N1 0 1 3 NTV ST 1
B
TEMP TEMP
1 2
10
F AN
15 16
Note: To update the data on temperature, use the Left and Right keys on the remote control unit.
PDP-504PU
5 6 7 8
61
62
Defective Assy
Cable disconnection CN4001 Check if the connection between the POWER SUPPLY and PANEL IF assemblies is properly made. ADY1081 Check if the FPC is broken or not securely inserted.
Symptom
1
Defective 114-pin FPC CN4004 - CN5001 Detection by the TRAP switch CN4006 Check if the TRAP switch is properly set. (See "7.1.4 Canceling detection of the TRAP switch".) ASG1089 Check if the unit works properly when detection of the TRAP switch is canceled. (See "7.1.4 Canceling detection of the TRAP switch.") Check if the system cables are securely connected. (See "7.1.5 Operation when the Media Receiver is not connected.") Defective TRAP switch Defective system cables CN4002, CN4003 System cables not connected Check connection of the system cables. (See "7.1.5 Operation when the Media Receiver is not connected.") Cable disconnection CN4801 - CN4851 ADD1225 Check if the FPCs are properly connected. Check if imparting vibration to the unit affects key inputs. Check if a pulse is output when the key corresponding to Pin 2 of the CN4852 is pressed. Check if the cables are disconnected or not securely connected. Check if a pulse is output when the key corresponding to Pin 5 of the CN4010 is pressed. Check if a pulse is output when the key corresponding to Pin 2 of the CN4852 is pressed. Check if the cables are not connected or securely connected. Cable disconnection CN4852 - CN4010 KEY CONTROL Defective KEY SCAN IC KEY CONTROL Assy IC4851 Cable disconnection CN4901 - CN4010 Check if the FPCs are properly connected. PANEL IR Defective infrared receiver PANEL IR U4901 Check if a pulse is output when the key corresponding to Pin 3 of the CN4010 is pressed. IC5401 Check if an abnormal area in the screen changes when the FPC connected to the address corresponding to the abnormal area is replaced with the one corresponding to the next address. IC4 BLOCK Check that an abnormal area in the screen does not change when the FPC connected to the address corresponding to the abnormal area is replaced with the one corresponding to the next address. Defective 114-pin FPC CN4004 - CN5001 ADY1081 Check if the FPC is broken or not securely inserted. DIGITAL VIDEO Defective IC4 ADDRESS
The power is interrupted, and the red and green warning indications appear on the screen.
PDP-504PU
7.1.5 CANCELING DETECTION BY THE TRAP SWITCH Canceling detection by the TRAP switch
Outline: For video data transmission from the Media Receiver to the plasma display, digital signals are used. Therefore, this unit adopts the HDCP (High-bandwidth Digital Content Protection) system for copyright protection. This unit is also provided with a detection switch (TRAP switch) that will prohibit the unit from being turned on again if the rear case of the unit is opened, in order to prevent the panel technology from being leaked out. Function: To deactivate the detection of the TRAP switch Purposes: 1. During production of this unit, adjusting with the rear cover opened is possible. 2. During servicing or repairing, diagnoses of the assemblies are possible while the power is on. Methods: For setting, use RS232C commands: TSN: Ignore the monitoring of the switch CTM: Clear the detection log of the switch TSY: Reactivate monitoring of the switch Notes:
The TRAP switch is located on the chassis (see Fig. below). Once rear case opening is detected, send the TSN and CTM commands. Because the TSN command is not stored in memory, monitoring of the switch can be reactivated by turning the unit off then back on. The same setting is possible using the Factory menu. Because the output of the DVI receiver is controlled by the physical setting of the TRAP switch, if the TRAP switch is set to OPEN, the DVI signal cannot be output even if the TSN command is sent. When the Media Receiver is connected, detection by the TRAP switch can be canceled by entering Factory mode.
A
How to enter Factory mode using the remote control unit Please refer to the technical documentation (Service knowhow). How to clear the detection log of the TRAP switch In the INITIALIZE layer, hold the OSD key on the remote control unit pressed for at least 3 seconds. After a power-down, to cancel detection of the TRAP switch using only the remote control unit, follow the procedures below. First, fix the TRAP switch to its depressed position. Set the drive ON/OFF switch in the DIGITAL VIDEO Assy to OFF, Then enter the Factory mode. Press the MUTE key four times, then hold the OSD key pressed for at least 3 seconds. Set the AC switch on the panel to OFF. The log is also cleared. Then set the drive ON/OFF switch to ON.
C
Rear View
TRAP switch
PDP-504PU
5 6 7 8
63
As the connection conditions of the system cables (MDR cable, DVI cable) are usually detected, if no connection, such as cable disconnection, is detected, a warning indication (alternate flashing of the red and green areas) is displayed on the mask screen, and the red and green LEDs flash alternately. Then after about 30 seconds, the power is automatically turned off.
Note: Only when the power is turned on again, a warning indication on the mask screen restarts. During standby, only the red and green LEDs flash alternately.
GREEN
B
RED
To operate the panel without the Media Receiver, there are the following two ways: 1. Operation-without-the-Media-Receiver mode Input the "SCN" RS232C command. The status of the LEDs changes to that in normal operation mode.
Note: Turning the AC switch to OFF then ON also maintains this mode. However, once the unit is connected with the Media Receiver using the MDR cable, this mode is automatically canceled.
2. DVI mode Turn the unit on while PC and DVI SG signals are being input with only the DVI connecter connected. After a warning is displayed for about 5 seconds, the unit is ready to display the screen of the input signal. (Green LED lit)
D
Notes: Although the output from XGA (43 inch) and WXGA (50 inch) can be input to the unit, this is not a mode open to general users. (With some signals, errors such as power-down may occur.) If a DE signal from the SG is not input during DVI mode, the green LED flashes (at intervals of 2 sec) for about 8 seconds, then the unit shifts to Power Management mode (the green LED lights).
Note: Temperature compensation is performed only for the VSUS voltage, and not for the VOFS voltage. This compensation is controlled by the software.
64
1 2
PDP-504PU
3 4
Methods: 1 Set the slide switch (S5201) on the DIGITAL VIDEO Assy to its upper position (see Fig. below). 2. Send the "DRF" RS232C command to turn the large-signal system off. 3. Send the "DRN" RS232C command to turn the large-signal system on.
Notes: As the unit enters Power-Down and Muting On mode when Methods 1 and 2 are performed, and power-downs other than those caused by the power (PS_PD) and DC-DC-converter (DIGITAL_DC-DC) circuits are not activated. If the slide switch is set from OFF to ON while the power is on, a power-down will occur. Be sure to turn the power off before switching the slide switch.
S5201
C
Rear View
DIGITAL VIDEO Assy
PDP-504PU
5 6 7 8
65
Outline
The data on the adjustment values for the main unit are stored in an EEPROM (IC5206, 4 kbits) on the DIGITAL VIDEO Assy. Part of the data (area A in the figure below) are automatically copied to an EEPROM (IC4002, 2 kbits) mounted on the PANEL IF Assy for backup. When the DIGITAL VIDEO Assy is replaced, the backup data on the adjustment values for the main unit stored in the PANEL IF Assy can be copied to the new DIGITAL VIDEO Assy, thus enabling you to omit newly performing adjustments on the main unit. The logs for the product (power-down log, etc.) can also be copied.
EEPROM on the PANEL IF Assy (for backup) 1 Power off 2 "BCP" command Backup data for the DIGITAL VIDEO Assy (Area B)
Backup data for the DIGITAL VIDEO Assy (Area A) Other data (Area C)
1 The keyword on the DIGITAL VIDEO Assy is checked when the power is turned off, and if it is "adjusted", automatic backup is performed. 2 If the keyword on the PANEL IF Assy (Area B) is "adjusted," copying can be performed with the "BCP" RS232C command.
2 "BCP" command
2. When a repaired DIGITAL VIDEO Assy is mounted on another unit (reuse of the repaired DIGITAL VIDEO Assy) The keyword of the DIGITAL VIDEO Assy to be reused must be changed to "not adjusted" using the "UAJ" RS232C command.
Note 1: If a repaired DIGITAL VIDEO Assy is mounted in another unit (Unit 2) without this change of keyword, and the power to the unit 2 is turned off, the data in force before the repair of the DIGITAL VIDEO Assy will be copied to Area B of the PANEL IF Assy of Unit 2, overwriting the data necessary for Unit 2. Once overwritten, the original data will not be restored.
66
1 2
PDP-504PU
3 4
3. When a repaired DIGITAL VIDEO Assy is mounted on the original unit (reuse of the repaired DIGITAL VIDEO Assy) Changing of keywords is not required. After the repaired DIGITAL VIDEO Assy is mounted in the original unit, the unit can operate with its latest adjustment values. 4. When both the DIGITAL VIDEO Assy and PANEL IF Assy are simultaneously replaced with other assemblies The automatic backup function of this unit will not work properly.
Note 2: Readjustment of the main unit is required. Note 3: After readjustment of the main unit, send the "FAJ" RS232C command to change the keyword of the DIGITAL VIDEO Assy to "adjusted." Thus, when the unit is turned off, automatic backup of adjustment data is performed properly. Note 4: If readjustment of the main unit is totally impossible, it can be omitted by installing the EEPROM (IC5206, 4 kbits) originally mounted on the DIGITAL VIDEO Assy for service.
Miscellaneous
If the white balance (W/B) value is largely shifted because of aging, etc., W/B adjustment is required. (As this may be a rare case, the adjustment procedures are described below, just for your reference.
[ W/B-adjustment procedures ]
The W/B adjustment can be performed with the RS232C commands with the Media Receiver not connected to this unit. The GGF1475 special communication tool and a Minolta CA-100 color difference meter are required. 1 Enter Operation-without-the-Media-Receiver mode with the "SCN" RS232C command. 2 Set the keyword for the DIGITAL VIDEO Assy to "not adjusted" with the "UAJ" RS232C command.
C
3 Obtain the current adjustment values in the two adjustment tables (see "6.2.1 RS232C commands"). Shifting to Table 1: Send the "M51" and "F60" commands. Obtaining the adjustment values: Send the "GPW" command. Shifting to Table 2: Send the "M51" and "F75" commands. Obtaining the adjustment values: Send the "GPW" command. 4 Make settings for various functions. Send the "PPN," "SDN," "SPN," and "WAY" commands.
Note: After adjustment, when the POWER switch is set to OFF, these settings will be reset to the initial values.
5 For each table, set the brightness. Adjustment in Table 1: After sending the "F60" command, perform adjustment. Adjustment in Table 2: After sending the "F75" command, perform adjustment. For each table, change the RGB parameters so that the values measured using a Minolta color difference meter (CA-100) become as indicated below. In this case, any one of PRH, PGH, or PBH must be set to 256.
x y Left side of Mask H Right side of Mask H 284 292 "PRH***" : 000 - 511 "PGH***" : 000 - 511 "PBH***" : 000 - 511
6 Check after adjustment Shifting to Table 1: Send the "F60" command. Obtaining the adjustment values: Send the "GPW" command. Shifting to Table 2: Send the "F75" command. Obtaining the adjustment values: Send the "GPW" command. Check that the adjustment data have been changed. 7 Change the keyword for the DIGITAL VIDEO Assy to "adjusted" by sending the "FAJ" RS232C command.
Note: Use a Minolta CA-100 color difference meter or the equivalent for measurement. Otherwise, the specifications of the product cannot be assured.
E
PDP-504PU
5 6 7 8
67
7.1.10 DISASSEMBLY
A
1 2 3
Remove the grip by removing the 4 screws. Remove the 12 screws (B tight). Remove the 16 screws (M screws). Note: At the time of a re-assembly, please attach after fixing a positioning hole previously.
3 2 1
Grip
2 3
2 1
Grip 1
4
B
1 2 3 2 3
2
1 2 3 2
3 2 2
2
3
2 5 6 7
C
Remove the 3 screws (B tight). Remove the flexible cable (J211) from the PANEL KEY Assy. Remove the front case (50P).
Note: As the screws used for the front case are B tight (ABZ30P100FZK) and other screws used are M screws (AMZ30P060FZK), care must be taken not to use the screws in the wrong places.
7
When only the front case Assy (50P) is removed
2567 PANEL KEY Assy Front case Assy (50P)
Flat clamp
Flat clamp
Housing wire (50) with power (J110) Pass J108 through under J110. Care must be taken that the wires do not protrude from the front chassis.
Care must be taken that the A flexible cable is put on a gasket. wires do not protrude from the front chassis.
68
1 2
PDP-504PU
3 4
1 3 3 1 2 3
Remove the front case, then remove the screw that secures the IR holder. Remove the nylon rivet, then remove the IR holder. Remove the flat clamp, then remove the wires. IR holder Flat clamp
5 7
B
Nyron rivet
Remove the front chassis VL Assy (50), by removing the 5 screws (M screws).
4
PANEL LED Assy
4
D
Remove the PANEL LED Assy, by removing the screw (M screw). If the screw is not removed, the connectors on the PANEL LED Assy may be damaged.
6
Switch holder
Flat clamp
5
PANEL LED Assy
Remove the front chassis VR Assy (50), by removing the 4 screws (M screws).
7
F
PDP-504PU
5 6 7 8
69
3 50 SCAN A, B,
A
1 2 3 4
Remove the 4 screws (M screws). Remove the 6 screws (M screws). Remove the some connectors. Remove the multi base section.
1 1
B
50 SCAN B Assy
2 1 1 1
3
50 Y DRIVE Assy
50 SCAN A Assy
C
1 2
4 1
5 6
5
50 X DRIVE Assy
E
X CONNECTOR B Assy
6
4
X CONNECTOR A Assy
PANEL IF Assy
HD SP TERMINAL Assy
70
1 2
PDP-504PU
3 4
7.2 IC INFORMATION
The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.
List of IC
BA10393F, BA10358F, BA8274F, NJM2195L, MBM29PL160BD, SII169CTG100, STK795-512, STK795-511, LA4625, M30626FHPGP, PD5856A, AN16003A-K, BD3869AS
-IN1
1ch + 2ch
OUT2
+IN1
-IN2
VEE
+IN2
-IN1
1ch + 2ch
OUT2
+IN1
-IN2
VEE
+IN2
PDP-504PU
5 6 7 8
71
VCC 8
LY 7
SY 6
N.C. 5
Buffer
Buffer
1 N.C.
2 LX
3 SX
4 GND
Pin Function
Pin No. Pin Name
VCC
Equivalent Circuit
Pin Function
2 7
LX LY
35.7 GND
Buffer output
VCC
3 6
SX SY
35.7
Buffer input
GND
4 8
GND VCC
72
1 2
PDP-504PU
3 4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
42 41 40 39 38 36 35 34 33 32 31 30 29 28 27 26 25 24 24 23 22
Block Diagram
BASSOUT VREFIN
23
MODE1
MODE2
MODE3
OUTR
OUTL
VREF
FFR1
FFR2
FFR3
FFL1
FFL2
FFL3
TP3
TP2
INR
INL
TP1
NC
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
22
MODE
D
MODE2
MODE3
FOCUS
TruBass
H L
3D Stereo
L -1
H L
V+
MODE1
10
11
12
13
14
15
16
17
18
19
20
21
FILOUT
PCOUT
PCIN
FIL1
FIL2
FIL3
FIL4
FIL5
FIL6
FIL7
SFIL2
SFIL3
SFIL1
SVOL2
SVOL1
GND
NC
C3
C4
C1
C2
PDP-504PU
5 6 7 8
73
Pin Function
A
No.
SDIP42 SOP40 QFP48
Pin Name
Equivalent Circuit
V+
V+
V+
14
13
C1
10k
0V
V+
V+
V+
15
C
14
10
C2
10k
50
0V
V+
V+
16 17 18
15 16 17
11 14 15
V+/2
V+
V+
19 2 5
18 2 5
16 44 47
SVOL2 C4 FIL2
WIDTH
VR V+/2
74
1 2
PDP-504PU
3 4
Pin Function
No.
SDIP42 SOP40 QFP48
Pin Name
Equivalent Circuit
21
20
18
GND
GND
0V
22
21
19
V+
V+
V+
V+
V+
50k
50k
23
22
20
VREFIN
V+/2
C
V+
V+
V+
24 29 30 31 36 40 3
23 28 29 30 34 38 3
21 28 29 30 34 40 45
50
V+/2
50
V+
V+
V+
150k
25 26 27
24 25 26
22 23 26
3 2 1
E
150
0V
PDP-504PU
5 6 7 8
75
Pin Function
A
SDIP42
No.
SOP40 QFP48
Pin Name
Equivalent Circuit
V+ V+ V+
28 35 39
B
27 33 37
27 33 39
150
V+/2
V+
33 37
C
31 35
31 35
TP2 TP3
V+
V+
V+
41 42
39 40
41 42
INR INL
Rch Lch
150 50k
V+/2
VREF
V+
V+
V+
VREF
76
1 2
PDP-504PU
3 4
50
46
FIL1
50
V+/2
VCC VSS
Input/Output Buffers
B
WE
State Control
BYTE
Command Register Program Voltage Generator
CE OE
STB
Data Latch
STB
Y-Decoder
Y-Gating
Address Latch
X-Decoder
Cell Matrix
A0 to A19 A-1
D
PDP-504PU
5 6 7 8
77
HS_DJTR
OCK_INV
OGND
OVCC
ODCK
CTL3
QO1
QO0
DE
45
44
43
42
41
50
49
48
47
46
40
39
38
37
36
35
34
33
32
31
30
29
28
27
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 84 100 75 80 85 90 76 82 95 96 97 77 78 79 83 89 81 86 87 88 91 92 93 94 98 99
26 25 24 23 22 21 20 19 18 17 16
QE13 QE12 QE11 QE10 QE9 QE8 OGND OVCC QE7 QE6 QE5 QE4 QE3 QE2 QE1 QE0 PDO# SCDT
QO9 QO10 QO11 QO12 QO13 QO14 QO15 VCC GND QO16
SiI 169
100-pin TQFP
(Top View)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
C
ODD 8-bits RED
RESERVED
AVCC
EXT_RES
OGND
OVCC
AGND
AGND
AGND
AGND
AGND
DIFFERENTIAL SIGNALS
PLL
HS_DJTR
OCK_INV
RESET#
STAG_OUT
Block Diagram
PD#
PDO#
PIXS
PGND
AVCC
AVCC
RXC+
RX2+
RX1+
RX0+
RXC-
RX2-
RX1-
RX0-
AVCC
PVCC
QO23
SCL
I2C Slave
CTL3 QE[23:0]
E
RXC RX0 RX1 RX2
24 / encrypted data
XOR Mask
control
24 / unencrypted data
EXT_RES
78
1 2
PDP-504PU
3 4
Block Diagram
VCC 22 VDD 21 SUS-B 20 SUS-G 19 GND 18 VSUS 16 VSUS 15 VSUS 14 VSUS 13 VSUS 12 SUSGND 10 SUSGND 9 SUSGND 8 SUSGND 7 SUSGND 6 SUSOUT 4 SUSOUT 3 SUSOUT 2 SUSOUT 1 42 PSUS 43 N.C. 44 SUS-MSK
D
23 SUB-GND M1 Delay Circuit DRIVER M3 24 N.C. 25 N.C. 27 N.C. 29 PSUS 30 PSUS 31 PSUS M6 M5 32 PSUS 33 PSUS M8 M7 36 PSUS 37 PSUS 38 PSUS 39 PSUS 40 PSUS
C B
PDP-504PU
5 6 7 8
79
Block Diagram
23 SUB-GND M1 Delay Circuit DRIVER M3 24 N.C. 25 N.C. 27 N.C. 29 PSUS 30 PSUS 31 PSUS M6 M5 32 PSUS 33 PSUS M8 M7 36 PSUS 37 PSUS 38 PSUS 39 PSUS 40 PSUS
VDD 21
SUSOUT 2 SUSOUT 1
80
1 2
PDP-504PU
3 4
BIAS CIRCUIT
STANDBY SW
PREDRIVER IN2 6 + IN --
PREDRIVER
POWER
D
5 7
PDP-504PU
5 6 7 8
81
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
VSUS VOFS TXD_IC4 RXD_IC4 CLK_IC4 BYTE CNVSS NC NC RST_MD XOUT VSS XIN VCC1 NMI REM_B KEY_B RST2 HD_IN_B PD_MUTE PS_PD DCC_PD NC NC VD_IN EEPRST E_SCL E_SDA TXD RXD SCLK BUSY TXD0 RXD0 NC REQ_MD PSW_D WE_IC4 EPM IC4_RST IC4_CE IC4_BUSY REQ_IC4 CE PSIZE B_SCL B_SDA ADR_PD LED_G LED_R
[D/A] Vofs power control [D/A] Vofs power control 3 serial communication with IC4MANTA - data transmission 3 serial communication with IC4MANTA - data receive 3 serial communication with IC4MANTA - clock output (GND connection) Pin for processor mode setting (pull-down) NC pin NC pin Reset input Output for main clock GND Input for main clock Power supply = STB3.3V (pull-up) (Interruption) Remote control signal input (in the panel unit) (Interruption) Key signal input (in the panel unit) (Interruption) IC4 reset detection HD signal existence distinction Mute the power down output to the POWER SUPPLY Unit PD signal in the POWER SUPPLY Unit PD signal of DC-DC converter NC pin NC pin V. frequency count EEPROM power SW IIC clock output for EEPROM IIC data I/O for EEPROM Communication with flash ROM writer - data transmission Communication with flash ROM writer - data receive Communication with flash ROM writer - clock input Communication with flash ROM writer - busy output
UART communication with main UCOM (external PC) - data transmission UART communication with main UCOM (external PC) - data receive
O O O I O I I
I O I I I I I I O I I
L L L H H
I O O I/O O I I O O I O O O I O O I I I I O I/O I O O
L H
NC pin Communication request to the main UCOM Mute of DC-DC converter In IC4 (MANTA) rewriting, control for communication path switch Setting pin for flash rewriting mode (pull-down) IC4 forced reset Enable for IC4 communication Busy input for IC4 communication Communication request from the IC4 Setting pin for flash rewriting mode (pull-up) Panel size distinction IIC clock output for backup EEPROM IIC DATA I/O for backup EEPROM PD signal of address junction Green LED control Red LED control
H H H L L H H
H H H L L
82
1 2
PDP-504PU
3 4
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
DRV_OFF RELAY POWER MR_ST_B OP_DET NC PNL_MUTE DITHER NC VCC2 PD_TRG VSS VH_PD YDRV_PD YRES_PD YDCDC_PD IC5V_PD XSUS_PD XDCDC_PD XDRV_PD NC MR_AC AC_DET DVI_MUTE A_MUTE A_NG A_SCL A_SDA TRUBASS STB_SW FOCUS SRS DDC_WP DVI_DET RSTBTMDS L_SYNC NC NC MASK1 MAX_PLS2 MAX_PLS1 TEMP MODE AVSS MODEL VREF AVCC NC NC AMG_MD
Driving OFF Power ON control output Power ON control input MDR connection detection Rear case open detection NC pin Panel mute PC/VIDEO dither switch (panel module exclusive use) NC pin Power supply = STB 3.3V PD detection GND Vh power decrease PD Y drive PD signal Y drive PD signal PD signal of Y drive DC-DC converter 5V power decrease PD X drive PD signal PD signal of X drive DC-DC converter X drive PD signal NC pin MR power monitor AC power monitor at panel side (same signal as CST1) Mute of panel link output Audio mute Audio NG detection IIC clock output for audio/others IIC data I/O for audio/others TRUBASS ON/OFF Standby setting of audio amp. FOCUS ON/OFF SRS ON/OFF DDCROM write protection DVI cable disconnection detection Reset detection of panel link receiver DE omission detection of the panel link NC pin NC pin [A/D] Mask display setting [A/D] Brightness setting for panel module [A/D] Brightness setting for panel module [A/D] AD input for temperature sensor [A/D] Operation mode setting GND for A/D input [A/D] CMX/HD/TV/WX distinction Reference voltage for A/D input Power supply for A/D input = STB3.3V NC pin NC pin Address emergency monitor
O O I I I I I I I I I I I I I I I I O O I O I/O O O O O O I I I
H H H L
L H H H H H H H H H L H H L L L H L H H H H L L
I I I I I I
PDP-504PU
5 6 7 8
83
A1 B1 C1 D1 E1 F1 G1 H1 J1 K1 L1 M1 N1 P1 R1 T1 U1 V1 W1 Y1 AA1 AB1 AC1 AD1 AE1 AF1 AF2 AF3 AF4 AF5 AF6 AF7 AF8 AF9 AF10 AF11 AF12 AF13 AF14 AF15 AF16 AF17 AF18 AF19 AF20 AF21 AF22 AF23 AF24 AF25
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
BAI_6 BAI_5 BAI_4 NC NC BAI_3 BAI_2 FIELD XSUSB_12 XSUSB_10 XSUSB_4 XSUSB_0 XSUSA_10 XSUSA_4 XSUSA_2 ADRS_0 AD6TXOUT3M AD6TXCLKOUTM AD6TXOUT2M AD6TXOUT1M AD6TXOUT0M AD7TXOUT3M AD7TXCLKOUTM AD7TXOUT2M AD7TXOUT1M AD7TXOUT0M AD7TXOUT0P VSSLA AD3TXOUT3M AD3TXCLKOUTM AD3TXOUT2M AD3TXOUT1M AD3TXOUT0M AD2TXOUT3M AD2TXCLKOUTM AD2TXOUT2M AD2TXOUT1M AD2TXOUT0M AD1TXOUT3M AD1TXCLKOUTM AD1TXOUT2M AD1TXOUT1M AD1TXOUT0M AD0TXOUT3M AD0TXCLKOUTM AD0TXOUT2M AD0TXOUT1M AD0TXOUT0M VSSL15 AD4TXOUT3P
A phase signal input of B video (sixth bit) A phase signal input of B video (fifth bit) A phase signal input of B video (fourth bit) NC pin NC pin A phase signal input of B video (fifth bit) A phase signal input of B video (fourth bit) FIELD signal input X-Drive control signal output X-Drive control signal output X-Drive control signal output X-Drive control signal output X-Drive control signal output X-Drive control signal output X-Drive control signal output Address control signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output GND Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output GND Address LVDS signal output
84
1 2
PDP-504PU
3 4
AF26 AE26 AD26 AC26 AB26 AA26 Y26 W26 V26 U26 T26 R26 P26 N26 M26 L26 K26 J26 H26 G26 F26 E26 D26 C26 B26 A26 A25 A24 A23 A22 A21 A20 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
AD4TXOUT3M AD4TXCLKOUTM AD4TXOUT2M AD4TXOUT1M AD4TXOUT0M AD5TXOUT3M AD5TXCLKOUTM AD5TXOUT2M AD5TXOUT1M AD5TXOUT0M SDIDBI_N SDIJTAG GPIO0_3 GPIO0_1 YSUSA_4 YSUSA_10 YSUSA_14 YSUSB_4 YSUSB_6 YSUSB_10 YSUSB_14 NC NC SCAN_10 CSIOTXD CSRD_N CSCS_N0 EXA16 EXA15 EXA14 EXA13 EXA12 EXA10 EXA7 EXA1 EXDIO_3 EXDIO_5 EXDIO_11 TRNSEND_O RBI_5 RBI_0 GBI_8 GBI_2 BBI_6 BBI_0 VDI RAI_5 DCLKI GAI_4 BAI_9
Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output JTAG signal JTAG signal Microcomputer macro general-purpose port Microcomputer macro general-purpose port Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output NC pin NC pin Scan control signal output Communication with microcomputer Communication with microcomputer Communication with microcomputer Flash memory address bus Flash memory address bus Flash memory address bus Flash memory address bus Flash memory address bus Flash memory address bus Flash memory address bus Flash memory address bus Flash memory data bus Flash memory data bus Flash memory data bus NC pin B phase signal input of R video (fifth bit) B phase signal input of R video (0 bit) B phase signal input of G video (eighth bit) B phase signal input of G video (second bit) B phase signal input of B video (sixth bit) B phase signal input of B video (0 bit) VD signal input A phase signal input of R video (fifth bit) CLK input A phase signal input of G video (fourth bit) A phase signal input of B video (ninth bit)
PDP-504PU
5 6 7 8
85
B2 C2 D2 E2 F2 G2 H2 J2 K2 L2 M2 N2 P2 R2 T2 U2 V2 W2 Y2 AA2 AB2 AC2 AD2 AE2 AE3 AE4 AE5 AE6 AE7 AE8 AE9 AE10 AE11 AE12 AE13 AE14 AE15 AE16 AE17 AE18 AE19 AE20 AE21 AE22 AE23 AE24 AE25 AD25 AC25 AB25
101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150
BAI_8 BAI_7 GND NC NC BAI_1 XSUSB_15 GND XSUSB_9 XSUSB_3 XSUSA_15 XSUSA_9 GND XSUSA_1 TEST2 AD6TXOUT3P AD6TXCLKOUTP AD6TXOUT2P AD6TXOUT1P AD6TXOUT0P AD7TXOUT3P AD7TXCLKOUTP AD7TXOUT2P AD7TXOUT1P VSSLA AD3TXOUT3P AD3TXCLKOUTP AD3TXOUT2P AD3TXOUT1P AD3TXOUT0P AD2TXOUT3P AD2TXCLKOUTP AD2TXOUT2P AD2TXOUT1P AD2TXOUT0P AD1TXOUT3P AD1TXCLKOUTP AD1TXOUT2P AD1TXOUT1P AD1TXOUT0P AD0TXOUT3P AD0TXCLKOUTP AD0TXOUT2P AD0TXOUT1P AD0TXOUT0P VSSL15 AD4TXCLKOUTP AD4TXOUT2P AD4TXOUT1P AD4TXOUT0P
A phase signal input of B video (eighth bit) A phase signal input of B video (seventh bit) GND NC NC A phase signal input of B video (first bit) X-Drive control signal output GND X-Drive control signal output X-Drive control signal output X-Drive control signal output X-Drive control signal output GND X-Drive control signal output Test signal input (Not used) Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output GND Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output GND Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output
86
1 2
PDP-504PU
3 4
AA25 Y25 W25 V25 U25 T25 R25 P25 N25 M25 L25 K25 J25 H25 G25 F25 E25 D25 C25 B25 B24 B23 B22 B21 B20 B19 B18 B17 B16 B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 C3 D3 E3 F3 G3 H3 J3 K3
151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200
AD5TXOUT3P AD5TXCLKOUTP AD5TXOUT2P AD5TXOUT1P AD5TXOUT0P SDITRST_N RESETX GND GPIO0_0 YSUSA_5 YSUSA_11 YSUSA_15 GND YSUSB_7 YSUSB_11 NC NC GND SCAN_11 CSIORXD CSIOSCKI UARTTXD UARTRXD CSWR_N0 GND EXA9 EXA6 EXA0 GND EXDIO_6 EXDIO_12 RBI_9 RBI_4 GND GBI_7 GBI_1 BBI_5 GND HDI RAI_4 GAI_9 GAI_3 GAI_2 VDDD33 GAI_1 GAI_0 NC XSUSB_14 VDDIO XSUSB_8
Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output Address LVDS signal output JTAG signal Reset input GND Microcomputer macro general-purpose port Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output GND Y-Drive control signal output Y-Drive control signal output NC pin NC pin GND Scan control signal output Communication with UCOM Communication with UCOM Communication with UCOM Communication with UCOM Communication with UCOM GND Flash memory address bus Flash memory address bus Flash memory address bus GND Flash memory data bus Flash memory data bus B phase signal input of R video (ninth bit) B phase signal input of R video (fourth bit) GND B phase signal input of G video (seventh bit) B phase signal input of G video (first bit) B phase signal input of B video (fifth bit) GND HD signal input A phase signal input of R video (fourth bit) A phase signal input of G video (ninth bit) A phase signal input of G video (third bit) A phase signal input of G video (second bit) 3.3V power supply A phase signal input of G video (first bit) A phase signal input of G video (0 bit) NC pin X-Drive control signal output 3.3V power supply X-Drive control signal output
PDP-504PU
5 6 7 8
87
L3 M3 N3 P3 R3 T3 U3 V3 W3 Y3 AA3 AB3 AC3 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 AD16 AD17 AD18 AD19 AD20 AD21 AD22 AD23 AD24 AC24 AB24 AA24 Y24 W24 V24 U24 T24 R24 P24 N24 M24 L24 K24 J24
201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250
XSUSB_2 XSUSA_14 XSUSA_8 VDDIO XSUSA_0 TEST1 VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA VSSLA SDITDO GPIO0_7 VDDIO YSUSA_0 YSUSA_6 YSUSA_12 YSUSB_0 VDDD33
X-Drive control signal output X-Drive control signal output X-Drive control signal output 3.3V power supply X-Drive control signal output Test signal input (Not used) GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND JTAG signal Microcomputer macro general-purpose port 3.3V power supply Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output 3.3V power supply
88
1 2
PDP-504PU
3 4
H24 G24 F24 E24 D24 C24 C23 C22 C21 C20 C19 C18 C17 C16 C15 C14 C13 C12 C11 C10 C9 C8 C7 C6 C5 C4 D4 E4 F4 G4 H4 J4 K4 L4 M4 N4 P4 R4 T4 U4 V4 W4 Y4 AA4 AB4 AC4 AC5 AC6 AC7 AC8
251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300
YSUSB_8 NC YSUSB_15 SCAN_3 VDDD33 SCAN_12 SCAN_13 SCAN_14 SCAN_15 VDDIO EXA8 EXA5 CLKD VDDIO EXDIO_7 EXDIO_13 RBI_8 RBI_3 VDDIO GBI_6 GBI_0 BBI_4 VDDIO RAI_9 RAI_3 GAI_8 GAI_7 GAI_6 GAI_5 VCMP XSUSB_13 XSUSB_11 XSUSB_7 XSUSB_1 XSUSA_13 XSUSA_7 XSUSA_3 ADRS_3 TESTAN VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA
Y-Drive control signal output NC pin Y-Drive control signal output Scan control signal output 3.3V power supply Scan control signal output Scan control signal output Scan control signal output Scan control signal output 3.3V power supply Flash memory address bus Flash memory address bus CLK input (60MHz) 3.3V power supply Flash memory data bus Flash memory data bus B phase signal input of R video (eighth bit) B phase signal input of R video (third bit) 3.3V power supply B phase signal input of G video (sixth bit) B phase signal input of G video (0 bit) B phase signal input of B video (fourth bit) 3.3V power supply A phase signal input of R video (ninth bit) A phase signal input of R video (third bit) A phase signal input of G video (eighth bit) A phase signal input of G video (seventh bit) A phase signal input of G video (sixth bit) A phase signal input of G video (fifth bit) GND X-Drive control signal output X-Drive control signal output X-Drive control signal output X-Drive control signal output X-Drive control signal output X-Drive control signal output X-Drive control signal output Address control signal output Test signal input (Not used) 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply
PDP-504PU
5 6 7 8
89
AC8 AC9 AC10 AC11 AC12 AC13 AC14 AC15 AC16 AC17 AC18 AC19 AC20 AC21 AC22 AC23 AB23 AA23 Y23 W23 V23 U23 T23 R23 P23 N23 M23 L23 K23 J23 H23 G23 F23 E23 D23 D22 D21 D20 D19 D18 D17 D16 D15 D14 D13 D12 D11 D10 D9 D8
300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349
VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDBG VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA VDDLA SDITDI GPIO0_6 GPIO0_2 YSUSA_1 YSUSA_7 YSUSA_13 YSUSB_1 YSUSB_5 YSUSB_9 VCMP SCAN_0 SCAN_4 SCAN_7 SCAN_8 SCAN_9 EXA11 EXA19 EXA4 EXDIO_0 EXDIO_4 EXDIO_8 EXDIO_14 RBI_7 RBI_2 GBI_9 GBI_5 BBI_9 BBI_3
3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supplyv 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply JTAG signal Microcomputer macro general-purpose port Microcomputer macro general-purpose port Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output Y-Drive control signal output GND Scan control signal output Scan control signal output Scan control signal output Scan control signal output Scan control signal output Flash memory address bus Flash memory address bus Flash memory address bus Flash memory data bus Flash memory data bus Flash memory data bus Flash memory data bus B phase signal input of R video (seventh bit) B phase signal input of R video (second bit) B phase signal input of G video (ninth bit) B phase signal input of G video (fifth bit) B phase signal input of B video (ninth bit) B phase signal input of B video (tenth bit)
90
1 2
PDP-504PU
3 4
D7 D6 D5 E5 F5 G5 H5 J5 K5 L5 M5 N5 P5 R5 T5 U5 V5 W5 Y5 AA5 AB5 AB6 AB7 AB8 AB9 AB10 AB11 AB12 AB13 AB14 AB15 AB16 AB17 AB18 AB19 AB20 AB21 AB22 AA22 Y22 W22 V22 U22 T22 R22 P22 N22 M22 L22 K22
350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399
DEI RAI_8 RAI_2 RAI_1 RAI_0 BAI_0 VSS15 VDDHR XSUSB_6 VSSD15 XSUSA_12 XSUSA_6 VSS15 ADRS_2 TESTBN VSSL15 VSSLA VSSLA VSSL15 VDDLP VSSL15 VSSLA VSSLA VSSL15 VSSLA VSSLA VSSL15 VSSLA VSSLA REFRIN VSSBG VSSL15 VSSLA VSSLA VSSL15 VSSLA VSSLA VSSLA VDDLA VSSL15 VSSLA VSSLA VSSL15 SDITMS GPIO0_5 VSS15 YSUSA_2 YSUSA_8 VSSD15 YSUSB_2
DE signal input A phase signal input of R video (eighth bit) A phase signal input of R video (second bit) A phase signal input of R video (first bit) A phase signal input of R video (0 bit) A phase signal input of B video (0 bit) GND 3.3V power supply X-Drive control signal output GND X-Drive control signal output X-Drive control signal output GND Address control signal output Test signal input (Not used) GND GND GND GND 3.3V power supply GND GND GND GND GND GND GND GND GND Reference current generation GND GND GND GND GND GND GND GND 3.3V power supply GND GND GND GND JTAG signal Microcomputer macro general-purpose port GND Y-Drive control signal output Y-Drive control signal output GND Y-Drive control signal output
PDP-504PU
5 6 7 8
91
J22 H22 G22 F22 E22 E21 E20 E19 E18 E17 E16 E15 E14 E13 E12 E11 E10 E8 E9 E7 E6 F6 G6 H6 J6 K6 L6 M6 N6 P6 R6 T6 U6 V6 W6 Y6 AA6 AA7 AA8 AA9 AA10 AA11 AA12 AA13 AA14 AA15 AA16 AA17 AA18 AA19
400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 418 417 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449
VDDHL VSSD15 YSUSB_12 SCAN_1 SCAN_5 SCAN_6 VSS15 EXA18 EXA3 EXDIO_1 VSS15 EXDIO_9 EXDIO_15 RBI_6 CLKS VSS15 GBI_4 BBI_2 BBI_8 VSS15 RAI_7 RAI_6 APL_DT VDD15 VBB XSUSB_5 VDDD15 XSUSA_11 XSUSA_5 VDD15 ADRS_1 TESTCN VDDL15 VDDLA VDDLA VDDL15 VDDLA VDDLA VDDL15 VDDLA VDDLA VDDL15 VDDLA VDDLA VDDLA VDDLA VDDL15 VDDLA VDDLA VDDL15
3.3V power supply GND Y-Drive control signal output Scan control signal output Scan control signal output Scan control signal output GND Flash memory address bus Flash memory address bus Flash memory data bus GND Flash memory data bus Flash memory data bus B phase signal input of R video (sixth bit) CLK input (85MHz) GND B phase signal input of G video (fourth bit) B phase signal input of B video (second bit) B phase signal input of B video (eighth bit) GND A phase signal input of R video (seventh bit) A phase signal input of R video (sixth bit) APL value trigger input 1.5V power supply VBB power monitor in the DRAM X-Drive control signal output 1.5V power supply X-Drive control signal output X-Drive control signal output 1.5V power supply Address control signal output Test signal input (Not used) 1.5V power supply 3.3V power supply 3.3V power supply 1.5V power supply 3.3V power supply 3.3V power supply 1.5V power supply 3.3V power supply 3.3V power supply 1.5V power supply 3.3V power supply 3.3V power supply 3.3V power supply 3.3V power supply 1.5V power supply 3.3V power supply 3.3V power supply 1.5V power supply
92
1 2
PDP-504PU
3 4
AA20 AA21 Y21 W21 V21 U21 T21 R21 P21 N21 M21 L21 K21 J21 H21 G21 F21 F20 F19 F18 F17 F16 F15 F14 F13 F12 F11 F10 F9 F8 F7
450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480
VDDLA VDDLA VDDL15 VDDLA VDDLA VDDL15 SDITCK GPIO0_4 VDD15 YSUSA_3 YSUSA_9 VDDD15 YSUSB_3 VBB VDDD15 YSUSB_13 SCAN_2 VDD15 EXA17 EXA2 EXDIO_2 VDD15 EXDIO_10 TRNSEND_I VDD15 RBI_1 VDD15 GBI_3 BBI_7 BBI_1 VDD15
3.3V power supply 3.3V power supply 1.5V power supply 3.3V power supply 3.3V power supply 1.5V power supply JTAG signal Microcomputer macro general-purpose port 1.5V power supply Y-Drive control signal output Y-Drive control signal output 1.5V power supply Y-Drive control signal output VBB power monitor in the DRAM 1.5V power supply Y-Drive control signal output Scan control signal output 1.5V power supply Flash memory address bus Flash memory address bus Flash memory data bus 1.5V power supply Flash memory data bus NC pin 1.5V power supply B phase signal input of R video (first bit) 1.5V power supply B phase signal input of G video (third bit) B phase signal input of B video (seventh bit) B phase signal input of B video (first bit) 1.5V power supply
PDP-504PU
5 6 7 8
93
AN16003A-K (50 SCAN A ASSY : IC3001 - IC3006) (50 SCAN B ASSY : IC3201 - IC3206)
Plasma Display Panel IC Pin Arrangement (Top view)
94
1 2
PDP-504PU
3 4
AN16003A-K (50 SCAN A ASSY : IC3001 - IC3006) (50 SCAN B ASSY : IC3201 - IC3206)
Plasma Display Panel IC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
OUT3 OUT4 OUT5 OUT6 OUT7 OUT8 OUT9 OUT10 OUT11 OUT12 OUT13 OUT14 OUT15 OUT16 OUT17 OUT18 OUT19 OUT20 OUT21 OUT22 OUT23 OUT24 OUT25 OUT26 OUT27 OUT28 OUT29 OUT30 N.C GND GND GND N.C VDDH VDDH OUT31 OUT32 OUT33 OUT34 OUT35 VDDH VDDH N.C GND GND GND N.C OUT36 OUT37 OUT38
Output
Not connected GND pin GND pin GND pin Not connected High-voltage circuit supply pin High-voltage circuit supply pin
Output
High-voltage circuit supply pin High-voltage circuit supply pin Not connected GND pin GND pin GND pin Not connected
F
PDP-504PU
5 6 7 8
95
AN16003A-K (50 SCAN A ASSY : IC3001 - IC3006) (50 SCAN B ASSY : IC3201 - IC3206)
A
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85
OUT39 OUT40 OUT41 OUT42 OUT43 OUT44 OUT45 OUT46 OUT47 OUT48 OUT49 OUT50 OUT51 OUT52 OUT53 OUT54 OUT55 OUT56 OUT57 OUT58 OUT59 OUT60 OUT61 OUT62 OUT63 OUT64 N.C VDDH VDDH N.C GND GND GND DIR SO CLK
Output
86
87 88 89
F
Not connected High-voltage circuit supply pin High-voltage circuit supply pin Not connected GND pin GND pin GND pin Setup pin of sift register sift direction Input L: Shift into reverse (SO = SI) H: Shift forward (SI = SO) Input/Output Serial data input/output pin Serial clock input pin Input Fetch SI or SO data to sift register by CLK rise edge LAT data input pin Input L: Transfer shft register data to output latch H: Hold data to output latch Supply Logic supply pin Output control pin Control output according to the right truth value table OC1 OC2 OUT L L ALL HiZ L H DATA H L ALL L H H ALL H
Input 90 OC2
96
1 2
PDP-504PU
3 4
AN16003A-K (50 SCAN A ASSY : IC3001 - IC3006) (50 SCAN B ASSY : IC3201 - IC3206)
Plasma Display Panel IC
91 92 93 94 95 96 97 98 99 100
Serial data input/output pin All output reset pin CLK pin: L = Normal operation CLK pin: H = All output High GND pin GND pin GND pin Not connected High-voltage circuit supply pin High-voltage circuit supply pin High-voltage push-pull output pin High-voltage push-pull output pin
PDP-504PU
5 6 7 8
97
f=80Hz
I2 C B U S L o g i c
f=80Hz
MUTE
BASS
B
BASS
MUTE
REAR VOLUME
REAR VOLUME
25K
VCC/2
+
25K
f=15kHz
TREBLE FRONT VOLUME
f=15kHz
TREBLE
FRONT VOLUME
1 FT1
2 FT2
3 IN1
4 LOUD1
5 IN2
6 LOUD2
CHIP F I L T E R G N D
Pin Function
No. Pin Name Function Pin Description
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
FT1 FT2 IN1 LOUD1 IN2 LOUD2 CHIP FILTER GND SDA SCL VCC OUT1 OUT2 FB12 FB11 FB21 FB22
CH1 Treble Filter Setting Pin CH2 Treble Filter Setting Pin CH1 Input Pin CH1 Loudness Filter Setting Pin CH2 Input Pin CH2 Loudness Filter Setting Pin Chip Select Pin 1/2 VCC Pin Ground pin I2C Communication Data Pin I2C Communication Data Pin Power Supply Pin CH1 Output Pin CH2 Output Pin CH1 Bass Filter Setting Pin CH1 Bass Filter Setting Pin CH2 Bass Filter Setting Pin CH2 Bass Filter Setting Pin
A pin for setting Treble frequency characteristic A pin for Inputting sound signal to main volume A pin for setting the loudness frequency characteristics and gain A pin for Inputting sound signal to main volume A pin for setting the loudness frequency characteristics and gain Terminal of Slave address select of I2C Bus 1/2 VCC. Voltage for power supply of signal system A ground pin Terminal of SDA of I2C bus. ACKNOWLEDGE signal is outputted. Data terminal Terminal of SCL of I2C bus. Clock terminal Power Supply Pin A pin for outputting a sound signal. Connect this pin to a rear stage circuit through a coupling capacitor A pin for setting Bass frequency characteristic and gain
98
1 2
PDP-504PU
3 4
5 6 7
B
2 1 3
1 2 3 4
Rear view
9 0
The terminals have faced downward.
99
8
Front view
(right view)
5 6 7
2 1
C
9 0
The terminals have faced downward.
100
1 2
PDP-504PU
3 4