Changing of + 145 depends on the supply voltage. If it's necessary to measure high voltage, Connect the probe of high voltage tester to the anode of CPT. 2Adjust contrast and brightness to minimum. 3Measure the high voltage as 27 KV for 25" and 28" screen size. 4for maximum brightness, high voltage regulation should be 2KV dc max.
Changing of + 145 depends on the supply voltage. If it's necessary to measure high voltage, Connect the probe of high voltage tester to the anode of CPT. 2Adjust contrast and brightness to minimum. 3Measure the high voltage as 27 KV for 25" and 28" screen size. 4for maximum brightness, high voltage regulation should be 2KV dc max.
Changing of + 145 depends on the supply voltage. If it's necessary to measure high voltage, Connect the probe of high voltage tester to the anode of CPT. 2Adjust contrast and brightness to minimum. 3Measure the high voltage as 27 KV for 25" and 28" screen size. 4for maximum brightness, high voltage regulation should be 2KV dc max.
SM-2 Chassis 28" Service Manual
SERVICE ADJUSTMENT AMSTRAD
AND ALIGNMENTS CTV3128N
HIGH VOLTAGE TEST
There is no high voltage adjustment component on the chassis. Changing of +145
depends on the supply voltage. IF it’s necessary to measure high voltage.
1- Connect the probe of high voltage tester to the anode of CPT
2. Adjust contrast and brightness to mininnum.
3+ Measure the high voltage as 27 KV for 25” and 28" screen size.
4. For maximum brightness, high voltage regulation should be 2kV de max.
AGC ADJUSTMENT
1- Apply Philips pattern signal which is 60 dB UV to the RF input.
2 “Adjust P30] unt find a picture without snowy.
VERTICAL ADJUSTMENT
1- Apply Philips pattem.
2- Adjust the vertical amplitude with P576 until the top and the bottom lines of the
picture appear.
3 Center the picture with PS79
HORIZONTAL ADJUSTMENT
1. Apply Phiips pattern signal.
2 Center the picture horizontally by shiffing to the left and right positions via P300.
ADJUSTMENT OF G2
1- Apply Philips test pattern
2- Adjust all the analog parameters to minimum with RC
3+ Adjust G2 until the maximum cathode voitage is ]75V.
ADJUSTMENT OF SUPPLY VOLTAGE
1- Apply Philips pattern signal.
2. Set the volume, brightness and contrast values to minimum.
3- Adjust the supply vottage on the PIN cathode of D125 as Vsys = 145 + 0.5 by
using P101
EDAD HADARADDADAANDTDADADADAADHMHAHHK AANASM-2 Chassis 28" Service Manual
FAULT TRACING DIAGRAM - POWER SUPPLY
‘SWITCHED MODE POWER SUPPLY
DEFECTIVE, + 145V iS MISSING OR
e101, c 102 YES Fuse (Ft LEVEL IS WRONG
r om = it detective
—
wo
| Y
R01, O07
H¢—>{ open and short Voltage at dai
aw
cireit
‘Contra range of
‘witched-mode‘SM-2 Chassis 26" Service Manual
OSCILLOSCOPE SIGNALS
1) Susn/100 volts/div
2) 20 usn/2 volts/div
3) 5 msn/2 volts/div
4) 5 msn/0.5 volt/div
q Sooo peo
pay io: oe FE
Hey + 1
th Hq coo SN
Coot Chere
EEE BEES EERE Ht
Drain of Q101 1301 pin 36 1301 pin 37 101 pin 42
5) 5msn/1 volt/div. 6) 5msn/20 volts/div 7) 20usn/2 volts/div 8) 20usn/div 2 volt/div
T ae T T T al TTT TTT
EEE HHH rece] = ARE)
Te | t 1 qj r
4
Coot cot FF H rH
CoCr} oot | EHH im
1876 pin3 1576 pin 5 110) pin 38
9) 20usn/2 volts/div 10) 10usn/2 volts/div 11) 10usn/250 votts/div 12) 20 usn/0.5 volt/div
COO oO [ T CT
EEE va TH Got aan
i E
RE Ao He AE Ut
Hee ree 4 Toot HH T
Coco rot Comper Ee
101 pin 19 1101 pin Collector of Q602 1101 pin 37
Coon
Collector of Q580
60
14) 20usn/1 volt/div
N01 pin 13