Professional Documents
Culture Documents
d-COPIA 16-200 - Service Manual (Y102911-6)
d-COPIA 16-200 - Service Manual (Y102911-6)
PUBLICATION ISSUED BY: Olivetti Tecnost S.p.A. 77, Via Jervis - 10015 Ivrea (TO) Italy
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturers instructions.
CAUTION
Double-pole/neutral fusing.
Y102911-6
Service Manual
iii
Safety precautions
This booklet provides safety warnings and precautions for our service personnel to ensure the safety of their customers, their machines as well as themselves during maintenance activities. Service personnel are advised to read this booklet carefully to familiarize themselves with the warnings and precautions described here before engaging in maintenance activities.
iv
Service Manual
Y102911-6
DANGER: High risk of serious bodily injury or death may result from insufficient attention to or incorrect compliance with warning messages using this symbol. WARNING:Serious bodily injury or death may result from insufficient attention to or incorrect compliance with warning messages using this symbol. CAUTION: Bodily injury or damage to property may result from insufficient attention to or incorrect compliance with warning messages using this symbol. Symbols The triangle ( ) symbol indicates a warning including danger and caution. The specific point of attention is shown inside the symbol. General warning. Warning of risk of electric shock. Warning of high temperature. indicates a prohibited action. The specific prohibition is shown inside the symbol. General prohibited action. Disassembly prohibited. indicates that action is required. The specific action required is shown inside the symbol. General action required. Remove the power plug from the wall outlet. Always ground the copier.
Y102911-6
Service Manual
1. Installation Precautions
WARNING Do not use a power supply with a voltage other than that specified. Avoid multiple connections to one outlet: they may cause fire or electric shock. When using an extension cable, always check that it is adequate for the rated current. ............................................................................................ Connect the ground wire to a suitable grounding point. Not grounding the copier may cause fire or electric shock. Connecting the earth wire to an object not approved for the purpose may cause explosion or electric shock. Never connect the ground cable to any of the following: gas pipes, lightning rods, ground cables for telephone lines and water pipes or faucets not approved by the proper authorities. .............................................................................................................................
CAUTION: Do not place the copier on an infirm or angled surface: the copier may tip over, causing injury. .....
Do not install the copier in a humid or dusty place. This may cause fire or electric shock. .............. Do not install the copier near a radiator, heater, other heat source or near flammable material. This may cause fire. ..........................................................................................................................
Allow sufficient space around the copier to allow the ventilation grills to keep the machine as cool as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ..........
Always handle the machine by the correct locations when moving it. .............................................. Always use anti-toppling and locking devices on copiers so equipped. Failure to do this may cause the copier to move unexpectedly or topple, leading to injury. ................................................. Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is accidentally ingested, drink a lot of water to dilute it in the stomach and obtain medical attention immediately. If it gets into the eyes, rinse immediately with copious amounts of water and obtain medical attention. .............................................................................................................................. Advice customers that they must always follow the safety warnings and precautions in the copiers instruction handbook. ........................................................................................................................
vi
Service Manual
Y102911-6
Always follow the procedures for maintenance described in the service manual and other related brochures. .........................................................................................................................................
Under no circumstances attempt to bypass or disable safety features including safety mechanisms and protective circuits. .................................................................................................
Always use parts having the correct specifications. .......................................................................... Always use the thermostat or thermal fuse specified in the service manual or other related brochure when replacing them. Using a piece of wire, for example, could lead to fire or other serious accident. ...............................................................................................................................
When the service manual or other serious brochure specifies a distance or gap for installation of a part, always use the correct scale and measure carefully. ...............................................................
Always check that the copier is correctly connected to an outlet with a ground connection. ............ Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it is dirty, clean it to remove the risk of fire or electric shock. ............................................................
Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may damage eyesight. .............................................................................................................................. Handle the charger sections with care. They are charged to high potentials and may cause electric shock if handled improperly. .................................................................................................
CAUTION Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are safely secured so they will not be caught in rotating sections...........................................................
Use utmost caution when working on a powered machine. Keep away from chains and belts. .......
Handle the fixing section with care to avoid burns as it can be extremely hot. .................................
Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause abnormally high temperatures. ..........................................................................................................
Do not remove the ozone filter, if any, from the copier except for routine replacement. ...................
Y102911-6
Service Manual
vii
Do not pull on the AC power cord or connector wires on high-voltage components when removing them; always hold the plug itself. ......................................................................................................
Do not route the power cable where it may be stood on or trapped. If necessary, protect it with a cable cover or other appropriate item. ..............................................................................................
Treat the ends of the wire carefully when installing a new charger wire to avoid electric leaks........ Remove toner completely from electronic components. ...................................................................
Run wire harnesses carefully so that wires will not be trapped or damaged. ................................... After maintenance, always check that all the parts, screws, connectors and wires that were removed, have been refitted correctly. Special attention should be paid to any forgotten connector, trapped wire and missing screws. .................................................................................. Check that all the caution labels that should be present on the machine according to the instruction handbook are clean and not peeling. Replace with new ones if necessary. ...................
Handle greases and solvents with care by following the instructions below: .................................... Use only a small amount of solvent at a time, being careful not to spill. Wipe spills off completely. Ventilate the room well while using grease or solvents. Allow applied solvents to evaporate completely before refitting the covers or turning the main switch on. Always wash hands afterwards. Never dispose of toner or toner bottles in fire. Toner may cause sparks when exposed directly to fire in a furnace, etc. .......................................................................................................................... Should smoke be seen coming from the copier, remove the power plug from the wall outlet immediately. ......................................................................................................................................
3. Miscellaneous
WARNING Never attempt to heat the drum or expose it to any organic solvents such as alcohol, other than the specified refiner; it may generate toxic gas. ................................................................................
viii
Service Manual
Y102911-6
CONTENTS
1-1 Specifications
1-1-1 Specifications ....................................................................................................................................... 1-1-2 Parts names and their functions ........................................................................................................... (1) Copier ............................................................................................................................................. (2) Operation panel .............................................................................................................................. 1-1-3 Machine cross section .......................................................................................................................... 1-1-4 Drive system ........................................................................................................................................ 1-1-1 1-1-3 1-1-3 1-1-4 1-1-5 1-1-6
1-3 Installation
1-3-1 Unpacking and installation ................................................................................................................... 1-3-1 (1) Installation procedure ..................................................................................................................... 1-3-1 1-3-2 Setting initial copy modes .................................................................................................................... 1-3-5 1-3-3 Installing the paper feeder (option) ...................................................................................................... 1-3-6 1-3-4 Installing the DP (option) ...................................................................................................................... 1-3-8 1-3-5 Installing the duplex unit (option) ....................................................................................................... 1-3-11 1-3-6 Installing the drawer heater (option) ................................................................................................... 1-3-14 1-3-7 Installing the key counter (option) ...................................................................................................... 1-3-17
1-5 Troubleshooting
1-5-1 Paper misfeed detection ...................................................................................................................... 1-5-1 (1) Paper misfeed indication ................................................................................................................ 1-5-1 (2) Paper misfeed detection conditions ................................................................................................ 1-5-2 (3) Paper misfeeds ............................................................................................................................... 1-5-6 1-5-2 Self-diagnosis ..................................................................................................................................... 1-5-15 (1) Self-diagnostic function ................................................................................................................ 1-5-15 (2) Self-diagnostic codes ................................................................................................................... 1-5-15 1-5-3 Image formation problems ................................................................................................................. 1-5-20 (1) No image appears (entirely white). ............................................................................................... 1-5-21 (2) No image appears (entirely black). ............................................................................................... 1-5-21 (3) Image is too light. ......................................................................................................................... 1-5-22 (4) Background is visible. ................................................................................................................... 1-5-22 (5) A white line appears longitudinally. .............................................................................................. 1-5-22 (6) A black line appears longitudinally. .............................................................................................. 1-5-23 1-1-1 (7) A black line appears laterally. ....................................................................................................... 1-5-23 (8) One side of the copy image is darker than the other. ................................................................... 1-5-23 (9) Black dots appear on the image. .................................................................................................. 1-5-24 (10) Image is blurred. ........................................................................................................................... 1-5-24 (11) The leading edge of the image is consistently misaligned with the original. ................................ 1-5-24 (12) The leading edge of the image is sporadically misaligned with the original. ................................ 1-5-25 (13) Paper creases. ............................................................................................................................. 1-5-25
Y102911-6
Service Manual
ix
(14) Offset occurs. ............................................................................................................................... (15) Image is partly missing. ................................................................................................................ (16) Fixing is poor. ............................................................................................................................... (17) Image is out of focus. ................................................................................................................... (18) Image center does not align with the original center. ................................................................... 1-5-4 Electrical problems ............................................................................................................................. (1) The machine does not operate when the power switch is turned on. ........................................... (2) The drive motor does not operate (C2000). ................................................................................. (3) The registration motor does not operate. ..................................................................................... (4) The exit motor does not operate. .................................................................................................. (5) The scanner motor does not operate. .......................................................................................... (6) Cooling fan motor 1 does not operate. ......................................................................................... (7) Cooling fan motor 2 does not operate. ......................................................................................... (8) The paper feed clutch does not operate. ...................................................................................... (9) The bypass paper feed clutch does not operate. ......................................................................... (10) The cleaning lamp does not turn on. ............................................................................................ (11) The exposure lamp does not turn on. ........................................................................................... (12) The exposure lamp does not turn off. ........................................................................................... (13) The fixing heater does not turn on (C6000). ................................................................................. (14) The fixing heater does not turn off. ............................................................................................... (15) Main charging is not performed. ................................................................................................... (16) Transfer charging is not performed. ............................................................................................. (17) No developing bias is output. ....................................................................................................... (18) The original size is not detected. .................................................................................................. (19) The original size is not detected correctly. ................................................................................... (20) The message requesting paper to be loaded is shown when paper is present in the drawer. ..... (21) The size of paper in the drawer is not displayed correctly. ........................................................... (22) A paper jam in the paper feed, paper conveying or fixing section is indicated when the power switch is turned on. ...................................................................................................... (23) The message requesting covers to be closed is displayed when the front cover and left cover are closed. .................................................................................................................... (24) Others. .......................................................................................................................................... 1-5-5 Mechanical problems ......................................................................................................................... (1) No primary paper feed. ................................................................................................................. (2) No secondary paper feed. ............................................................................................................ (3) Skewed paper feed. ...................................................................................................................... (4) The scanner does not travel. ........................................................................................................ (5) Multiple sheets of paper are fed at one time. ................................................................................. (6) Paper jams. .................................................................................................................................. (7) Toner drops on the paper conveying path. ................................................................................... (8) Abnormal noise is heard. ..............................................................................................................
1-5-25 1-5-26 1-5-26 1-5-26 1-5-27 1-5-28 1-5-28 1-5-28 1-5-28 1-5-28 1-5-29 1-5-29 1-5-29 1-5-29 1-5-29 1-5-29 1-5-29 1-5-30 1-5-30 1-5-30 1-5-30 1-5-30 1-5-30 1-5-30 1-5-30 1-5-31 1-5-31 1-5-31 1-5-31 1-5-31 1-5-32 1-5-32 1-5-32 1-5-32 1-5-32 1-5-32 1-5-32 1-5-32 1-5-32
Service Manual
Y102911-6
1-6-3 Optical section .................................................................................................................................... (1) Detaching and refitting the exposure lamp ................................................................................... (2) Detaching and refitting the scanner wires .................................................................................... (2-1) Detaching the scanner wires ............................................................................................... (2-2) Fitting the scanner wires ...................................................................................................... (3) Detaching and refitting the ISU (reference) .................................................................................. (4) Detaching and refitting the laser scanner unit .............................................................................. (5) Adjusting the longitudinal squareness (reference) ....................................................................... (6) Adjusting magnification of the scanner in the main scanning direction ........................................ (7) Adjusting magnification of the scanner in the auxiliary scanning direction ................................... (8) Adjusting the scanner leading edge registration ........................................................................... (9) Adjusting the scanner center line ................................................................................................. (10) Adjusting the margins for scanning an original on the contact glass ............................................ 1-6-4 Drum section ....................................................................................................................................... (1) Detaching and refitting the drum unit ............................................................................................ (2) Detaching and refitting the drum separation claws ....................................................................... (3) Detaching and refitting the main charger unit ............................................................................... 1-6-5 Developing section .............................................................................................................................. (1) Detaching and refitting the developing unit .................................................................................. 1-6-6 Transfer section .................................................................................................................................. (1) Detaching and refitting the transfer roller ..................................................................................... 1-6-7 Fixing section ...................................................................................................................................... (1) Detaching and refitting the fixing unit ........................................................................................... (2) Detaching and refitting the press roller ......................................................................................... (3) Detaching and refitting the fixing heater M and S ......................................................................... (4) Detaching and refitting the heat roller separation claws ............................................................... (5) Detaching and refitting the heat roller ........................................................................................... (6) Detaching and refitting the fixing thermostat ................................................................................ (7) Detaching and refitting the fixing thermistor .................................................................................
1-6-17 1-6-17 1-6-18 1-6-18 1-6-20 1-6-23 1-6-24 1-6-27 1-6-28 1-6-29 1-6-30 1-6-31 1-6-32 1-6-33 1-6-33 1-6-34 1-6-35 1-6-36 1-6-36 1-6-37 1-6-37 1-6-38 1-6-38 1-6-39 1-6-40 1-6-41 1-6-42 1-6-43 1-6-43
2-2-1 Electrical parts layout ........................................................................................................................... (1) PCBs .............................................................................................................................................. (2) Switches and sensors ..................................................................................................................... (3) Motors ............................................................................................................................................. (4) Other electrical components ...........................................................................................................
Y102911-6
Service Manual
xi
2-4 Appendixes
Timing chart No. 1 .......................................................................................................................................... 2-4-1 Timing chart No. 2 .......................................................................................................................................... 2-4-2 Timing chart No. 3 .......................................................................................................................................... 2-4-3 Timing chart No. 4 .......................................................................................................................................... 2-4-4 Chart of image adjustment procedures .......................................................................................................... 2-4-5 Maintenance parts list ..................................................................................................................................... 2-4-8 Periodic maintenance procedures .................................................................................................................. 2-4-9 Optional devices supplied parts list .............................................................................................................. 2-4-11 General wiring diagram ................................................................................................................................ 2-4-12
1-1-4
xii
Service Manual
Y102911-6
1-1-1 Specifications
Type ............................................... Desktop Copying system .............................. Indirect electrostatic system Originals ......................................... Sheets, books and 3-dimensional objects (Maximum original size: A3) Maximum size: A3/11" 17" Original feed system ...................... Fixed Copy paper ..................................... Paper weights Drawer: 64 105 g/m2 Bypass table: 45 160 g/m2 Paper type Drawer: Plain paper, recycled paper and colored paper Bypass table: Plain paper, recycled paper, thin paper, thick paper and colored paper Copying sizes ................................. Maximum: A3/11" 17" Minimum: A6R /51/2" 81/2" Magnification ratios ........................ Manual mode: 50 200%, 1% increments Copy speed .................................... At 100% magnification in copy mode: 16cpm machine 20cpm machine A4: 16 copies/min. A4: 20 copies/min. A4R: 13 copies/min. A4R: 13 copies/min. A3: 8 copies/min. A3: 10 copies/min. A5R: 10 copies/min. A5R: 10 copies/min. A6R: 10 copies/min. A6R: 10 copies/min. B5: 16 copies/min. B5: 20 copies/min. B5R: 13 copies/min. B5R: 13 copies/min. B4 (257 364 mm): 8 copies/min. B4 (257 364 mm): 11 copies/min. 11" 81/2": 16 copies/min. 11" 81/2": 20 copies/min. 81/2" 11": 10 copies/min. 81/2" 11": 13 copies/min. 11" 17": 8 copies/min. 11" 17": 10 copies/min. 81/2" 14": 8 copies/min. 81/2" 14": 11 copies/min. First copy time ................................ Approximately 5.9 s (A4/11" 81/2") Warm-up time ................................. Less then 19.8 s (room temperature 20C/68F, 50% RH) Paper feed system ......................... Automatic feed Capacity: Drawers: 300 sheets (80 g/m2) Manual feed Capacity: Bypass: 50 sheets (A4/11" 81/2" or less) 25 sheets (A3, B4, 11" 17", 81/2" 14") Paper ejection system .................... In-machine ejection (face down) Capacity: 250 sheets (80 g/m2) Continuous copying ........................ 1 250 sheets Photoconductor .............................. OPC (drum diameter 30 mm) Charging system ............................ Single positive corona charging Recording system .......................... Semiconductor laser Developing system ......................... Single component developing system Toner: magnetism toner Toner replenishing: automatic from a toner container Transfer system ............................. Transfer roller Separation system ......................... Curvature separation and separation electrode Fixing system ................................. Heat roller Heat source: halogen heaters (120 V specifications:main 550 W, sub 400W/ 220-240 V specifications:main 600 W, sub 450 W) Control temperature: 170C/338F (180C/356F on and after 6th sheet) Abnormally high temperature protection device: 180C/356F thermostat Fixing pressure: 44.1 N Charge erasing system .................. Exposure by cleaning lamp Cleaning system ............................. Cleaning blade Scanning system ............................ Flat bed scanning by CCD image sensor Bitmap memory .............................. 18 MB (standard) Image storage memory .................. 14 MB (standard) Resolution ...................................... 600 600 dpi
Y102911-6
Service Manual
1-1-1
Light source .................................... Inert gas lamp Dimensions .................................... 574 (W) 552 (D) 545 (H) mm 225/8" (W) 213/4" (D) 211/2" (H) Weight ............................................ Approx. 40.7 kg/89.7 lbs Floor requirements ......................... 827 (W) 552 (D) mm 325/8" (W) 213/4" (D) Functions ........................................ Automatic paper selection, Image quality selection, Automatic sizeing selection function, zoom function, Duplex copy, Divided copy, Binding margin, Border width, Aggregate copy, Sort copy, Eco-copy, Copy program and Section management mode Power source ................................. 120 V AC, 60 Hz, 9.0 A 220 240 V AC, 50 Hz, 5.0 A (Average) Options ........................................... Document processer, paper feeder, duplex unit, key counter
Duplex unit Type ............................................... Internal type Copy paper ..................................... Paper weights: 64 90 g/m2 Paper type: Plain paper, recycled paper and colored paper Paper sizes .................................... A3 A5R/11" 17" 51/2" 81/2" Power source ................................. Electrically connected to the copier Dimensions .................................... 368 (W) 53 (D) 180 (H) mm 141/2" (W) 21/16" (D) 71/16" (H) Weight ............................................ Approx. 0.65 kg/1.43 lbs
1-1-2
Service Manual
Y102911-6
Figure 1-1-1
1 Original cover 2 Copy storage section 3 Operation panel 4 Drawer 5 Width guide 6 Length guide 7 Left cover handle 8 Bypass tray 9 Support guide 0 Slider
! Contact glass @ Original size indicator plate # Left cover $ Waste toner box % Toner container release lever ^ Toner container & Cleaner rod * Front cover ( Power switch
Y102911-6
Service Manual
1-1-3
Inch
Figure 1-1-2 1 Start key (Indicator) 2 Stop/Clear key 3 Reset key 4 Numeric keys 5 Energy Saver key (Indicator) 6 Interrupt key (Indicator) 7 Management key 8 Auto Exposure key 9 Copy exposure adjustment keys (Indicators) 0 Eco-copy key ! Image mode selection key @ Program key # Copy quantity/magnification display $ Zoom (+) key % Zoom (-) key ^ Recall%/Enter key & Magnification Select key * Paper Select key ( Paper supply indicator ) Paper supply level indicator Paper jam indicator Bypass tray indicator Original size Select key Toner recovery indicator Toner supply indicator Memory overflow indicator Maintenance indicator Auto Selection key Aggregate copy key Duplex copy key Divided key Sort key Border lightening key Margin key Printer type selection key
1-1-4
Service Manual
Y102911-6
1 2 3 4 5 6 7 8
Paper feed section Optical section Drum section Developing section Transfer and separation section Fixing section Exit and switchback section Duplex section
Y102911-6
Service Manual
1-1-5
Figure 1-1-4
1 2 3 4 5 6 7 8 9 0 ! @ # $
Drive motor gear Gear 122 Registration gear 51 Registration motor gear Gear 32 Gear 25 Gear 25 Gear 20 Paper feed clutch gear Gear 30 Gear 31 Gear 25 Gear 49 Gear 30/23
% ^ & * ( )
Developing gear 25 Developing gear 26 Fixing joint gear 29 Gear 40 Gear 40 Gear 88/34 Gear 40 Fixing joint gear 40 Coupling gear Gear 50 Gear 60 Exit motor gear Gear 43/20
1-1-6
Service Manual
Y102911-6
1-2-1 Drum
Note the following when handling or storing the drum. When removing the drum unit, never expose the drum surface to strong direct light. Keep the drum at an ambient temperature between 20C/4F and 55C/131F and at a relative humidity not higher than 90% RH. Avoid abrupt changes in temperature and humidity. Avoid exposure to any substance which is harmful to or may affect the quality of the drum. Do not touch the drum surface with any object. Should it be touched by hands or stained with oil, clean it.
1-2-2 Toner
Store the toner in a cool, dark place. Avoid direct light and high humidity.
Y102911-6
Service Manual
1-2-1
d a
f c
b e
a: 571 mm/221/2" b: 552 mm/213/4" c: 502 mm/193/4" d: 1371.5 mm/54" e: 1272 mm/501/16" f: 952.5 mm/371/2" Figure 1-2-1 Installation dimensions
1-2-2
Service Manual
Y102911-6
Start
Load paper. Remove the tapes and pins. Output an own-status report (maintenance item U000).
Y102911-6
Service Manual
1-3-1
Unpack.
( Original holder (Asia and Oceania) ) Operation guide Cassette size sheet Paper protection bag Error code label Inspection report
1-3-2
Service Manual
Y102911-6
Install the optional paper feeder. 1. Install the optional paper feeder as necessary (see page 1-3-6 to 1-3-7).
Tapes
Tape
Tapes
Tape Tapes
Figure 1-3-2
Pins
Figure 1-3-3
1. Install the original cover or optional DP (see page 1-3-8 to 1-3-10 when installing the DP).
Install the optional duplex unit. 1. Install the optional duplex unit as necessary (see pages 1-3-11 to 1-3-13).
Y102911-6
Service Manual
1-3-3
Install the toner container. 1. Open the front cover. 2. Tap the top of the toner container five to six times. 3. Shake the toner container approximately 10 times in the horizontal direction to stir toner. 4. Turn the toner container release lever and gently push the toner container into the copier. *Push the container all the way into the copier until it locks in place. 5. Restore the toner container release lever. 6. Close the front cover.
Toner container release lever
Toner container
Figure 1-3-4
Connect the power cord. 1. Connect the power cord to the connector on the copier. 2. Insert the power plug into the wall outlet and turn the power switch on. Installing the toner (maintenance item U130). 1. Enter the maintenance mode by entering 10871087 using the numeric keys. 2. Enter 130 using the numeric keys and press the start key. 3. Press the start key to execute the maintenance item. Installation of toner starts and "9" is indicated in the copy quantity display. Each time one minute elapses, the indicated value decrements. When the installation is complete, "Gd" will be displayed if the installation is successful or "nG" will be displayed if it has failed. 4. Press the stop/clear key. Load paper. 1. Load paper in the drawer. Output an own-status report (maintenance item U000). 1. Enter 000 using the numeric keys and press the start key. 2. Select d-L and press the start key to output a list of the current settings of the maintenance items. 3. Press the stop/clear key. Exit maintenance mode. 1. Enter "001" using the numeric keys and press the start key. The machine exits the maintenance mode. Make test copies. 1. Place an original and make test copies. Completion of the machine installation.
1-3-4
Service Manual
Y102911-6
Contents Switching between double and single counts Turning auto start function on/off Setting auto clear time Switching copy operation at toner empty detection Changing the copy count timing Setting the ejection restriction
Y102911-6
Service Manual
1-3-5
Paper feeder
Figure 1-3-5 For stacking paper feeders for use: Stack a paper feeder on another paper feeder by aligning the positioning insertion sections of the first paper feeder with the positioning pins at the rear part of the second paper feeder. (Up to three paper feeders can be stacked.)
Positioning pins
Positioning pins
Figure 1-3-6
2. If a type of paper that is not included in the specifications for the standard sheet cassette size is used, replace the cassette size sheet indication with the supplied one. 3. Insert the copier power plug into the wall outlet and turn the copier power switch on. Load paper in the drawer and make test copies to check the operation.
Figure 1-3-7
1-3-6
Service Manual
Y102911-6
Adjusting the leading edge timing 1. Run maintenance mode 034. Press the image quality mode key until "Text" is lit. (group 1) First paper feeder: Press the exposure key until "exp3" is lit. (mode 3) Second paper feeder: Press the exposure key until "exp4" is lit. (mode 4) Third paper feeder: Press the exposure key until "exp5" is lit. (mode 5) Make a test copy to check the image. If an adequate image cannot be obtained, carry out the following adjustment. 2. If a copy example a is obtained, increase the adjustment value. If a copy example b is obtained, decrease the adjustment value. Setting range: -5.0 - 10.0 3. Make a test copy again. 4. Repeat steps 2 and 3 until an adequate image is obtained.
Adequate image
Copy example a
Copy example b
Figure 1-3-8 Adjusting the center line 1. Run maintenance mode 034. Press the image quality mode key until "Text" and "Photo" are lit. (group 2) First paper feeder: Press the exposure key until "exp3" is lit. (mode 3) Second paper feeder: Press the exposure key until "exp4" is lit. (mode 4) Third paper feeder: Press the exposure key until "exp5" is lit. (mode 5) Make a test copy to check the image. If an adequate image cannot be obtained, carry out the following adjustment. 2. If a copy example a is obtained, increase the adjustment value. If a copy example b is obtained, decrease the adjustment value. Setting range: -8.0 - 10.0 3. Make a test copy again. 4. Repeat steps 2 and 3 until an adequate image is obtained.
Adequate image
Copy example a
Copy example b
Figure 1-3-9
Y102911-6
Service Manual
1-3-7
Figure 1-3-10
3. Place the DP on the copier by fitting the pins into the holes at the hinge sections of the DP and sliding them toward the front side.
DP Pin Pin
Hole
Hole
Figure 1-3-11
4. Secure the DP with the two chrome TP screws M4 x 10 and the two screws that have been removed in step 1.
DP
Figure 1-3-12
1-3-8
Service Manual
Y102911-6
5. Close the DP, fit the fixing fitting from the rear side of the right hinge, and secure it with the two bronze TP screws M3 x 06. 6. Connect the cable of the DP to the copier. * Be sure to tighten the fixing screws on both side of the connector. 7. Remove the screw from the rear cover and fit the connector protection plate to the rear cover using the screw.
Cable
Figure 1-3-13
8. Paste the caution label that corresponds to the language according to the destination to the DP.
Caution label
Figure 1-3-14
15mm
15mm
Center line
[Operation check] 1. Prepare an original on which 4 lines are drawn 15 mm from the edges and the center line is drawn. 2. Set the original on the DP and make a test copy to check the copy image. At this time, set the paper guide for the original table and drawer to the paper size to be used. 3. If the copy image does not match the original image, carry out the following adjustments in maintenance mode. Maintenance mode 070 (sub-scan line adjustment) Maintenance mode 071 (leading edge timing adjustment) Maintenance mode 072 (center line adjustment)
15mm
Lines
Lines
15mm
Original
Figure 1-3-15
Y102911-6
Service Manual
1-3-9
Maintenance mode 070 (sub-scan line adjustment) For copy example a: decrease the value. For copy example b: increase the value. Changing the value by one changes the sub-scan line by 0.1%. The larger the value, the larger the magnification of the sub-scan line of the copy image. The smaller the value, the smaller the magnification of the sub-scan line of the copy image.
Original
Copy example a
Copy example b
Figure 1-3-16 Maintenance mode 071 (leading edge timing adjustment) For copy example a: increase the value. For copy example b: decrease the value. Changing the value by one moves the leading edge by 0.17 mm. The larger the value, the later the image scan start timing. The smaller the value, the earlier the image scan start timing.
Original
Copy example a
Copy example b
Figure 1-3-17 Maintenance mode 072 (center line adjustment) For copy example a: increase the value. For copy example b: decrease the value. Changing the value by one moves the center line by 0.17 mm. The larger the value, the center of the image moves toward the right. The smaller the value, the center of the image moves toward the left.
Original
Copy example a
Copy example b
Figure 1-3-18
1-3-10
Service Manual
Y102911-6
Fitting projection
Stopper
Strap
Pin
Left cover
Figure 1-3-19
6. Turn the wire guide section of the duplex unit in the direction indicated by the arrow.
Figure 1-3-20
7. Insert the axis sections of the duplex unit into the Ushape grooves of the conveyer unit.
Axis section
Axis section
Duplex unit
Figure 1-3-21
Y102911-6
Service Manual
1-3-11
8. Press the duplex unit in the direction indicated by the arrow to fit the claws into the conveyer unit.
Duplex unit
Claw
Claw
Figure 1-3-22
9. Secure the duplex unit with the two S tite screws M3 x 06.
Duplex unit
S tite screws M3 x 06
Figure 1-3-23
10. Open the conveyer unit and connect the connector of the duplex unit to the copier. 11. Reattach the removed parts to their original positions. 12. Connect the copier power plug to the wall outlet and turn the copier power switch on.
Duplex unit
Connector
Figure 1-3-24
1-3-12
Service Manual
Y102911-6
Adjusting the leading edge timing 1. Run maintenance mode 034. Press the image quality mode key until "Text" is lit. (group 1) Press the exposure key until "exp1" is flashing. (mode 6) Make a test copy in the duplex mode to check the image. If an adequate image cannot be obtained, carry out the following adjustment. 2. If a copy example a is obtained, increase the adjustment value. If a copy example b is obtained, decrease the adjustment value. Setting range: -5.0 - 10.0 3. Make a test copy again. 4. Repeat steps 2 and 3 until an adequate image is obtained.
Adequate image
Copy example a
Copy example b
Figure 1-3-25 Adjusting the center line 1. Run maintenance mode 034. Press the image quality mode key until "Text" and "Photo" are lit. (group 2) Press the exposure key until "exp1" is flashing. (mode 6) Make a test copy in the duplex mode to check the image. If an adequate image cannot be obtained, carry out the following adjustment. 2. If a copy example a is obtained, increase the adjustment value. If a copy example b is obtained, decrease the adjustment value. Setting range: -8.0 - 10.0 3. Make a test copy again. 4. Repeat steps 2 and 3 until an adequate image is obtained.
Adequate image
Copy example a
Copy example b
Figure 1-3-26
Y102911-6
Service Manual
1-3-13
Figure 1-3-27
1-3-14
Service Manual
Y102911-6
4. Insert the cassette heater from the bottom of the machine and attach it to the copier. 1) Pass the connector of the cassette heater through the hole located in the right frame of the machine to pull it out. 2) Insert the projections at the rear side of the cassette heater mounting plate into the two holes in the rear frame of the machine. 3) Position the screw hole of the drawer heater to the screw hole of the front frame of the machine and secure the heater using the M4 10 Taptite S binding screw.
Figure 1-3-28
Y102911-6
Service Manual
1-3-15
5. Remove the two screws and open the power source PCB in the direction indicated by the arrow. * Take care not to open the power source PCB too much. 6. Fit the wire of the drawer heater into the groove of the frame and put it inside the power source PCB. * Fit the wire into the groove so that the band mounted to the wire is located above the frame.
Band
Figure 1-3-29
7. Reattach the power source PCB to its original position and connect the connector of the drawer heater to YC8 of the power source PCB. 8. Refit all the removed parts.
Connector
YC8
Figure 1-3-30
1-3-16
Service Manual
Y102911-6
Procedure 1. Fit the key counter socket assembly to the key counter retainer using the two screws and nut. 2. Fit the key counter mount to the key counter cover using the two screws, and attach the key counter retainer to the mount using the two screws.
M4 6 screws Key counter retainer Key counter mount M3 nut Key counter cover
M4 6 screws
Figure 1-3-31
Y102911-6
Service Manual
1-3-17
3. Remove the rear cover. 4. Cut out the aperture plate on the right cover using nippers. 5. Connect the 4-pin connector of the key counter wire (located at a longer distance from the tube) to YC13 on the engine PCB, pass the wire through the two clamps, and pull the other 4-pin connector out from the aperture of the right cover. * Arrange the key counter wire behind the optical system wire as shown in the illustration. 6. Fold the 7-pin connector of the key counter wire back, pass the wire through the clamp at the upper part of the controller box, and hang it.
Figure 1-3-32
7. Pass the connector of the key counter through the aperture of the key counter mounting plate, and engage the projection of key counter mounting plate with the square hole of the key counter cover.
Aperture
4-pin connector
Figure 1-3-33
1-3-18
Service Manual
Y102911-6
8. Connect the 4-pin connector of the key counter to the key counter wire. 9. Engage the projection of the key counter mounting plate with the aperture of the right cover. 10. Secure the key counter cover and the key counter mounting plate together with the copier using a M4 x 35 screw. 11. Refit the rear cover.
Aperture Key counter wire 4-pin connector Projection Key counter cover
Figure 1-3-34
12. Insert the key counter into the key counter socket assembly. 13. Turn the main switch on and enter the maintenance mode. 14. Run maintenance item U204 and select KEYCOUNTER. 15. Exit the maintenance mode. 16. Check that if the key counter is removed, U1 is displayed in the copy quantity display. 17. Check that the counter counts up as copies are made.
Y102911-6
Service Manual
1-3-19
The copier is equipped with a maintenance function which can be used to maintain and service the machine. (1) Executing a maintenance item
Start
Enter the maintenance item number using the zoom +/- keys or numeric keys.
Yes
No
Yes
No Enter 001 using the zoom +/- keys or numeric keys and press the start key.
End
Y102911-6
Service Manual
1-4-1
(2) Maintenance mode item list Section General Item No. Maintenance item contents Initial setting* 5.1/0/0/0/0/0 -1.2/0/0/0/0/0 330 210 20/0/70/80/80/0 0 0 0 0 0 0 0 12 0 0 12 10 0 0 0 0 0 0 1 35 Off 0/0/0
U000 Outputting an own-status report U001 Exiting the maintenance mode U004 Checking the machine number U005 Copying without paper U019 Displaying the ROM version U020 Initializing all data U021 Initializing memories U030 Checking motor operation U031 Checking switches for paper conveying U032 Checking clutch or solenoid operation U034 Setting paper timing Adjusting the leading edge registration Adjusting the center line U035 Setting folio size Length Width U051 Adjusting the amount of slack in the paper U053 Performing fine adjustment of the motor speed Drive motor speed adjustment Polygon motor speed adjustment Exit motor speed adjustment Registration motor speed adjustment Motor speed adjustment (for paper feed from bypass tray) Motor speed adjustment (for paper feed from optional paper feeder) Motor speed adjustment (in duplex mode)
Optical
U060 Adjusting the scanner input properties U061 Turning the exposure lamp on U063 Adjusting the shading position U065 Adjusting the scanner magnification Main scanning direction auxiliary scanning direction U066 Adjusting the leading edge registration for scanning an original on the contact glass U067 Adjusting the center line for scanning an original on the contact glass U068 Adjusting the scanning position for originals from the DP U070 Adjusting the DP magnification U071 Adjusting the DP scanning timing Adjusting leading edge registration Adjusting trailing edge registration U072 Adjusting the DP center line U073 Checking scanner operation U074 Adjusting the DP input light luminosity U087 Turning the DP scanning position adjust mode on/off U088 Setting the input filter (moir reduction mode) U089 Outputting a MIP-PG pattern U091 Checking shading U092 Adjusting the scanner automatically U093 Setting the exposure density gradient Text/text and photo/photo mode U099 Checking the original size detection
1-4-2
Service Manual
Y102911-6
Item Maintenance item contents No. U100 Setting the main high voltage Grid control voltage Copy interval Copy quantity Correction amount U101 Setting the other high voltages Developing bias clock frequency Developing bias clock duty Transfer control voltage (large size) Transfer control voltage (small size) Transfer charging output OFF timing Transfer charging output ON timing Separation control voltage Separation charging output ON timing Separation charging output OFF timing U110 Checking/clearing the drum count
Initial setting* 135 60 50 10 27 45 168 179 38 34 1 33 43 0 140 160 170 180 5 20 Off 150000 0 Japan A3 On 90 Single mode After ejection 0 1.0 On
Developing
U130 Toner install mode U144 Setting toner loading operation U158 Checking/clearing the developing count
U161 Setting the fixing control temperature Primary stabilization fixing temperature Secondary stabilization fixing temperature Copying operation temperature 1 Copying operation temperature 2 Number of sheets for fixing control Number of sheets for fixing control (thick paper) U162 Stabilizing fixing forcibly U163 Resetting the fixing problem data U167 Checking/clearing the fixing count U199 Checking the fixing temperature
U200 Turning all LEDs on U202 Setting the KMAS host monitoring system U203 Operating DP separately U204 Setting the presence or absence of a key card or key counter U207 Checking the operation panel keys U243 Checking the operation of the DP motors and solenoids U244 Checking the DP switches
Mode setting
U250 Setting the maintenance cycle U251 Checking/clearing the maintenance count U252 Setting the destination U253 Switching between double and single counts U254 Turning auto start function on/off U255 Setting auto clear time U258 Switching copy operation at toner empty detection U260 Changing the copy count timing U265 Setting the destination specifications U332 Setting the size conversion factor U342 Setting the ejection restriction U345 Setting the value for maintenance due indication
Y102911-6
Service Manual
1-4-3
Item Maintenance item contents No. U402 Adjusting margins of image printing U403 Adjusting margins for scanning an original on the contact glass U404 Adjusting margins for scanning an original from the DP U407 Adjusting the leading edge registration for memory image printing
Initial setting*
Others
U901 Checking/clearing copy counts by paper feed locations U903 Checking/clearing the paper jam counts U904 Checking/clearing the service call counts U905 Checking/clearing counts by the DP U908 Checking the total count U910 Clearing the black ratio data U911 Checking/clearing copy counts by paper size U927 Clearing accounting counter U928 Checking/clearing the machine life counts U990 Checking/clearing the time for the exposure lamp to light U991 Checking the scanner count U993 Outputting a VTC-PG pattern
1-4-4
Service Manual
Y102911-6
(3) Contents of maintenance mode items Maintenance item No. U000 Outputting an own-status report Description
Description Outputs lists of the current settings of the maintenance items, and paper jam and service call occurrences. Purpose To check the current setting of the maintenance items, or paper jam or service call occurrences. Before initializing the backup RAM, output a list of the current settings of the maintenance items to reenter the settings after initialization or replacement. Method 1. Press the start key. A selection item appears. 2. Select the item to be output using the copy exposure adjustment keys. Display d-L J-L C-L Output list List of the current settings of the maintenance modes List of the paper jam occurrences List of the service call occurrences
3. Press the start key. The test copy mode is entered and a list is output. When A4/11" 81/2" paper is available, a report of this size is output. If not, specify the paper feed location. When output is complete, the selected item appears. Completion Press the stop/clear key while a selection item is displayed. The indication for selecting a maintenance item No. appears. U001 Exiting the maintenance mode Description Exits the maintenance mode and returns to the normal copy mode. Purpose To exit the maintenance mode. Method Press the start key. The normal copy mode is entered. U004 Checking the machine number Description Displays the machine number. Purpose To check the machine number. Method 1. Press the start key. The currently set machine number is displayed. 2. Change the indication of the copy quantity display by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 5 (lit) Exp. 1 (flashing) Exp. 2 (flashing) Exp. 3 (flashing) Exp. 4 (flashing) Exp. 5 (flashing) Copy quantity display 1st digit of machine number 2nd digit of machine number 3rd digit of machine number 4th digit of machine number 5th digit of machine number 6th digit of machine number 7th digit of machine number 8th digit of machine number 9th digit of machine number 10th digit of machine number
Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-5
Description
Description Simulates the copy operation without paper feed. Purpose To check the overall operation of the machine. Method 1. Press the start key. A selection item appears. 2. Select the item to be operated using the copy exposure adjustment keys. Display P P-d Operation Only the copier operates. Both the copier and DP operate.
3. Press the interrupt key. 4. Set the operation conditions required. Changes in the following settings can be made. Paper feed locations Magnifications Number of copies: continuous copying is performed when set to 250. Copy density Keys on the operation panel other than the energy saver (preheat) key 5. To control the paper feed pulley, remove all the paper in the drawers, or the drawers. With the paper present, the paper feed pulley does not operate. 6. Press the start key. The operation starts. Copy operation is simulated without paper under the set conditions. When operation is complete, the selected item appears. 7. To stop continuous operation, press the stop/reset key. Completion Press the stop/clear key while a selection item is displayed. The indication for selecting a maintenance item No. appears. U019 Displaying the ROM version Description Displays the part number of the ROM fitted to each board. Purpose To check the part number or to decide if the ROM version is new from the last digit of the number. Method 1. Press the start key. A selection item appears. 2. Select the item to be displayed using the image mode selection key and copy exposure adjustment keys. Image mode LEDs Copy exposure indicator Exp. 1 Exp. 2 Exp. 1 Exp. 2 Exp. 1 Exp. 2 Exp. 3 Exp. 1 Copy quantity display number of the main ROM number of the main ROM sub number of the engine ROM number of the engine ROM sub number of the first paper feeder ROM number of the second paper feeder ROM number of the third paper feeder ROM number of the DP ROM
: Off,
: On,
: Flashing
Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-6
Service Manual
Y102911-6
Description
Description Initializes all the backup RAM on the main board to return to the original settings. Purpose Run as needed. Method 1. Press the start key. 2. Select on using the zoom +/ keys. Display on Operation Canceling initialization Executing initialization
3. Press the start key. All data in the backup RAM is initialized, and the original settings for Japan specifications are set. When initialization is complete, the machine automatically returns to the same status as when the main switch is turned on. Completion To exit this maintenance item without executing initialization, press the stop/clear key. The indication for selecting a maintenance item No. appears. U021 Initializing memories Description Initializes the setting data other than that for adjustments due to variations between respective machines, i.e., settings for counters, service call history and mode settings. As a result, initializes the backup RAM according to the specifications depending on the destination selected in U252. Purpose Used to return the machine settings to the factory settings. Method 1. Press the start key. 2. Select on using the zoom +/ keys. Display on Operation Canceling initialization Executing initialization
3. Press the start key. All data other than that for adjustments due to variations between machines is initialized based on the destination setting. When initialization is complete, the machine automatically returns to the same status as when the main switch is turned on. Completion To exit this maintenance item without executing initialization, press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-7
Maintenance item No. U030 Checking motor operation Description Drives each motor. Purpose To check the operation of each motor.
Description
Method 1. Press the start key. A selection item appears. 2. Select the motor to be operated using the copy exposure adjustment keys. Display A 2F F1 F2 F3 EJ1 EJ2 Motor Drive motor (DM) Registration motor (RM) Drawer drive motor 1 (DDM1)* Drawer drive motor 2 (DDM2)* Drawer drive motor 3 (DDM3)* Exit motor (EM) forward rotation Exit motor (EM) reverse rotation
*: Optional 3. Press the start key. The selected motor operates. 4. To stop operation, press the stop/reset key. Completion Press the stop/clear key after operation stops. The indication for selecting a maintenance item No. appears. U031 Checking switches for paper conveying Description Displays the on-off status of each paper detection switch on the paper path. Purpose To check if the switches for paper conveying operate correctly. Method 1. Press the start key. 2. Turn each switche on and off manually to check the status. When the on-status of a switch is detected, the original size indicator corresponding to the operated switch lights. Original size indicator A3R/Ledger A5R/Legal A4/Letter-R B4R/Letter B5R/Statement Folio/U *: Optional Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. Switch Exit switch (ESW) Registration switch (RSW) Drawer feed switch 1 (DFSW1)* Drawer feed switch 2 (DFSW2)* Feedshift switch (FSSW) Duplex paper conveying switch (DUPPCSW)*
1-4-8
Service Manual
Y102911-6
Maintenance item No. U032 Checking clutch or solenoid operation Description Turns each clutch or solenoid on.
Description
Purpose To check the operation of each clutch or solenoid. Method 1. Press the start key. A selection item appears. 2. Select the clutch or solenoid to be operated using the copy exposure adjustment keys. 3. Press the start key. The selected clutch or solenoid turns on for 1 s. Display P1 Pb F1 F2 F3 *: Optional Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U034 Adjusting the print start timing Adjustment See pages 1-6-12 and 14. U035 Setting folio size Description Changes the image area for copying onto folio size paper. Purpose To prevent the image at the trailing edge, or right or left side of the paper from not being copied by setting the actual size of the folio paper used. Method Press the start key. Setting 1. Select the item to be set using the copy exposure adjustment keys. 2. Change the setting using the zoom +/ keys. Copy exposure indicator Exp. 1 Exp. 2 Setting Length Width Setting range 330 to 356 mm 200 to 220 mm Initial setting 330 210 Clutch Paper feed clutch (PFCL) Bypass paper feed solenoid (BYPPFSOL) Drawer paper feed clutch 1 (DPFCL1)* Drawer paper feed clutch 2 (DPFCL2)* Drawer paper feed clutch 3 (DPFCL3)*
3. Press the start key. The value is set. Completion Press the stop/clear key. The screen for selecting a maintenance item No. is displayed. U051 Adjusting the amount of slack in the paper Adjustment See page 1-6-16.
Y102911-6
Service Manual
1-4-9
Maintenance Description item No. U053 Performing fine adjustment of the motor speed Description Performs fine adjustment of the speeds of the motors. Purpose Used to adjust the speed of the respective motors when the magnification is not correct. Also speed adjustment for each paper source can be performed in group 2. Method Press the start key. Setting 1. Select the group to be set or checked by lighting image mode LEDs using the image mode selection key. 2. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. 3. Change the setting using the zoom +/ keys. Image mode LED Copy exposure Description indicator Exp. 1 Exp. 2 Exp. 3 Exp. 4 Exp. 1 Exp. 2 Exp. 3 Drive motor speed adjustment Polygon motor speed adjustment Exit motor speed adjustment Registration motor speed adjustment Motor speed adjustment (for paper feed from bypass tray) Motor speed adjustment (for paper feed from optional paper feeder) Motor speed adjustment (in duplex mode) Setting range 5.0 to +5.0 5.0 to +5.0 5.0 to +5.0 5.0 to +5.0 Initial setting 0 0 0 0
Drive motor speed adjustment (unit: %) Increasing the setting makes the image longer in the auxiliary scanning direction, and decreasing it makes the image shorter in the auxiliary scanning direction. Polygon motor speed adjustment (unit: %) Increasing the setting makes the image longer in the main scanning direction and shorter in the auxiliary scanning direction; decreasing the setting makes the image shorter in the main scanning direction and longer in the auxiliary scanning direction. 4. Press the start key. The value is set. Interrupt copy mode While this maintenance item is being performed, a VTC pattern shown below is output in interrupt copy mode. Correct values for an A3/11" 17" output are: A = 300 1.5 mm B = 270 1.35 mm
Figure 1-4-1 Adjustment 1. Output an A3/11" 17" VTC pattern in interrupt mode. 2. Measure A and B on the VTC pattern (Figure 1-4-1), and perform the following adjustments if they are different from the correct sizes: A: Drive motor speed adjustment B: Polygon motor speed adjustment Completion Press the stop/clear key while a selection item is displayed. The indication for selecting a maintenance item No. appears.
1-4-10
Service Manual
Y102911-6
Maintenance item No. U060 Adjusting the scanner input properties Description Adjusts the image scanning density.
Description
Purpose Used when the entire image appears too dark or light. Method Press the start key. Setting 1. Change the setting using the zoom +/ keys. Description Image scanning density Setting range 0 to 23 Initial setting 12
Increasing the setting makes the density lower, and decreasing it makes the density higher. 2. Press the start key. The value is set. Test copy mode While this maintenance item is being performed, copying from an original can be made in test copy mode. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. Caution The following settings are also reset to the initial values by performing this maintenance item: Exposure density gradient set in maintenance mode (U093) Exposure set in the copy default item of the copier management mode U061 Turning the exposure lamp on Description Turns the exposure lamp on. Purpose To check the exposure lamp. Method 1. Press the start key. on appears. 2. Press the start key. The exposure lamp lights. 3. To turn the exposure lamp off, press the stop/clear key. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-11
Maintenance item No. U063 Adjusting the shading position Description Changes the shading position.
Description
Purpose Used when white lines continue to appear longitudinally on the image after the shading plate is cleaned. This is due to flaws or stains inside the shading plate. To prevent this problem, the shading position should be changed so that shading is possible without being affected by the flaws or stains. Method 1. Press the start key. 2. Change the setting using the zoom +/ keys. Description Shading position Setting range 5 to +5 Initial setting 0 Change in value per step 0.17 mm
Increasing the setting moves the shading position toward the machine left, and decreasing it moves the position toward the machine right. 3. Press the start key. The value is set. Test copy mode While this maintenance item is being performed, copying from an original can be made in test copy mode. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U065 Adjusting the scanner magnification Adjustment See pages 1-6-28 and 29. U066 Adjusting the leading edge registration for scanning an original on the contact glass Adjustment See page 1-6-30. U067 Adjusting the center line for scanning an original on the contact glass Adjustment See page 1-6-31. U068 Adjusting the scanning position for originals from the DP Description Adjusts the position for scanning originals from the DP. Purpose Used when there is a regular error between the leading edges of the original and the copy image when the DP is used. Method Press the start key. Setting 1. Change the setting using the zoom +/ keys. Description Scanning position Setting range 17 to +17 Initial setting 0 Change in value per step 0.254 mm
Increasing the setting moves the image backward, and decreasing it moves the image forward. 2. Press the start key. The value is set. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-12
Service Manual
Y102911-6
Maintenance item No. U070 Adjusting the DP magnification Description Adjusts the DP original scanning speed.
Description
Purpose To be executed if the correct magnification is not obtained in the auxiliary scanning direction when the optional DP is used. Caution Before making this adjustment, ensure that the following adjustments have been made in maintenance mode.
U053
U065
U070
Method Press the start key. Setting 1. Change the setting using the zoom +/ keys. Description Original conveying motor speed Setting range 25 to +25 Initial setting 0 Change in value per step 0.1%
Increasing the setting makes the image longer, and decreasing it makes the image shorter. 2. Press the start key. The value is set. Interrupt copy mode While this maintenance item is being performed, copying from an original can be made in interrupt copy mode. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-13
Maintenance item No. U071 Adjusting the DP scanning timing Description Adjusts the DP original scanning timing.
Description
Purpose To be executed if there is a regular error between the leading or trailing edges of the original and the copy image when the optional DP is used. Caution Before making this adjustment, ensure that the following adjustments have been made in maintenance mode.
U034
U066
U071
Method Press the start key. Setting 1. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. 2. Change the setting using the zoom +/ keys. Copy exposure indicator Exp. 1 Exp. 2 Description Change in Setting range Initial setting value per step 0 0 0.254 mm 0.254 mm
Decreasing the setting moves the copy image backward, and increasing it moves the copy image forward. 3. Press the start key. The value is set. Interrupt copy mode While this maintenance item is being performed, copying from an original can be made in interrupt copy mode. Adjustment 1. In interrupt copy mode, make a copy using the DP. 2. Check the copy image and adjust the registration as follows. For copy example 1, decrease the setting of exp.1. For copy example 2, increase the setting of exp.1.
Original
Copy example 1
Copy example 2
Figure 1-4-2 Completion Press the stop/clear key while a selection item is displayed. The indication for selecting a maintenance item No. appears.
1-4-14
Service Manual
Y102911-6
Description
Description Adjusts the scanning start position for the DP original. Purpose To be executed if there is a regular error between the centers of the original and the copy image when the optional DP is used. Caution Before making this adjustment, ensure that the following adjustments have been made in maintenance mode.
U034
U067
U072
Method Press the start key. Setting 1. Change the setting using the zoom +/ keys. Description DP center line Setting range 6.6 to +6.6 Initial setting 0.0 Change in value per step 0.1 mm
Increasing the setting moves the image to the right, and decreasing it moves the image to the left. 2. Press the start key. The value is set. Interrupt copy mode While this maintenance item is being performed, copying from an original can be made in interrupt copy mode. Adjustment 1. In interrupt copy mode, make a copy using the DP. 2. Check the copy image and adjust the center line as follows. For copy example 1, increase the setting. For copy example 2, decrease the setting.
Reference
Original
Copy example 1
Copy example 2
Figure 1-4-3 Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-15
Description
Description Simulates the scanner operation under arbitrary conditions. Purpose To check scanner operation. Method 1. Press the start key. 2. Select the item to be changed by lighting a copy exposure indicator using the copy exposure adjustment keys. 3. Change the setting using the zoom +/ keys. Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Paper size for each setting Setting 8 9 24 36 39 40 41 Paper size A4 B5 11" 81/2" A3 B4 A4R B5R Setting 42 47 52 53 55 56 58 Paper size A5R Folio 11" 17" 11" 15" 81/2" 14" 81/2" 11" 51/2" 81/2" Operating conditions Magnification Paper size On and off of the exposure lamp Setting range 50 to 200% See below. on or off
4. Press the interrupt key. 5. Press the start key. Scanning starts under the selected conditions. 6. To stop operation, press the stop/clear key. Completion Press the stop/clear key when scanning stops. The indication for selecting a maintenance item No. appears. U074 Adjusting the DP input light luminosity Description Adjusts the luminosity of the exposure lamp for scanning originals from the DP. Purpose Used if the exposure amount differs significantly between when scanning an original on the contact glass and when scanning an original from the DP. Method Press the start key. Setting 1. Change the setting using the zoom +/ keys. Description DP input light luminosity Setting range 0 to 8 Initial setting 1
Increasing the setting makes the luminosity higher, and decreasing it makes the luminosity lower. 2. Press the start key. The value is set. Test copy mode While this maintenance item is being performed, copying from an original can be made in test copy mode. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-16
Service Manual
Y102911-6
Maintenance Description item No. U087 Turning the DP scanning position adjust mode on/off Description Turns on or off the DP scanning position adjust mode, in which the DP original scanning position is adjusted automatically by determining the presence or absence of dust on the slit glass. Also changes the reference data for identifying dust. Reference In the DP original scanning position adjust mode, the presence or absence of dust is determined by comparing the scan data of the original trailing edge and that taken after the original is conveyed past the DP original scanning position. If dust is identified, the DP original scanning position is adjusted for the following originals. Purpose Used to prevent appearance of black lines due to dust adhering in the original scanning position on the slit glass when the DP is used. Method 1. Press the start key. 2. Select the item to be set by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Description Setting the mode on/off Setting the reference data for identifying dust
Setting the mode on/off 1. Select on or oFF using the zoom +/ keys. Display on oFF Initial setting: on 2. Press the start key. The setting is set. Setting the reference data for identifying dust Available only when the mode is turned on. 1. Change the setting using the zoom +/ keys. Description Minimum density to be regarded as dust Setting range 10 to 95 Initial setting 35 Description DP scanning position adjust mode on DP scanning position adjust mode off
Example The figure indicates the density in 256 levels of gray (0: white, 255: black). When the setting is 35, data of the level of 35 or higher is regarded as dust and data of lower level is regarded as the background (scan data taken when there is no original). 2. Press the start key. The value is set. Completion Press the stop/clear key while a selection item is displayed. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-17
Maintenance Description item No. U088 Setting the input filter (moir reduction mode) Description Turns moir reduction mode on and off by switching the input filter on and off. Purpose Used to prevent regular density unevenness (moir) on halftone image areas of the copy image in text mode and text and photo mode. Such moir is more likely to appear when an enlargement or reduction copy is made in text mode from an original containing large halftone image areas. Method Press the start key. Setting 1. Select on or oFF using the zoom +/ keys. Display on oFF Initial setting: oFF If moir on the copy image is significant, change the setting to on. Note that when the moir reduction mode is turned on, the resolution may be slightly reduced. 2. Press the start key. The value is set. The indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears. U089 Outputting a MIP-PG pattern Description Selects and outputs a MIP-PG pattern created in the copier. Purpose When performing respective image printing adjustments, used to check the machine status apart from that of the scanner with a non-scanned output MIP-PG pattern. Method 1. Press the start key. 2. Select the MIP-PG pattern to be output using the copy exposure adjustment keys. Display G-S 0 FFL 1-d Setting Gray scale Mono level 256 level 1-dot level Setting range 0 to 255 Initial setting 0 Description Moir reduction mode Normal copy mode
3. Press the interrupt key. The machine enters the PG pattern output mode. 4. Press the start key. A MIP-PG pattern is output. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-18
Service Manual
Y102911-6
Description
Description Performs scanning under the same conditions as before and after shading is performed, displaying the original scanning values at nine points of the contact glass. Purpose To check the change in original scanning values before and after shading. The results may be used to decide the causes for fixing unevenness (uneven density) of the gray area of an image: either due to optical (shading or CCD) or other problems. Also to check the causes for a white or black line appearing longitudinally. Method 1. Press the start key. A selection item appears. 2. Select the item to be operated using the zoom +/ keys. Display on oFF Operation Performs scanning before shading and displays the result. Performs scanning after shading and displays the result.
3. Press the start key. Scanning is performed under the selected conditions and the result is displayed. 4. Change the measurement point by lighting a copy exposure indicator or making one flash using the copy exposure adjustment keys. For the correspondence between the measurement points and the copy exposure indicators, see Figure 1-4-4.
100 mm from the machine center toward machine rear Machine center 100 mm from the machine center toward machine front 20 mm from the machine left
1 4 7
2 5 8
3 6 9
Point 1 2 3 4 5
Copy exposure indicator exp. 1 (lit) exp. 2 (lit) exp. 3 (lit) exp. 4 (lit) exp. 5 (lit)
Point 6 7 8 9
Copy exposure indicator exp. 1 (flashing) exp. 2 (flashing) exp. 3 (flashing) exp. 4 (flashing)
Figure 1-4-4 When scanning is performed before shading, the scan value at the machine center should be slightly different from those at the machine front and rear. When scanning is performed after shading, there should be no difference between respective values. Any differences between the values at machine front and rear indicates that scanner problem causes the fixing unevenness. If the displayed results indicate no shading problems, the fixing unevenness (uneven copy density) is caused by factors other than in the scanner section (shading or CCD). If a black line appears, the cause may be assumed based on the results of the scanning operation before shading: if a white line appears, they may be assumed based on the results of the scanning operation after shading. Note that depending on the thickness and location of the black or white line, it may not be possible to use this method to determine the cause. This is because the displayed values obtained from scanning at the limit of nine points are insufficient to provide significant information. 5. Press the stop/clear key. The selected item appears. Completion Press the stop/clear key while a selection item is displayed. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-19
Description
Description Makes auto scanner adjustments in the order below using the specified original. Adjusting the scanner center line (U067) Adjusting the scanner leading edge registration (U066) Adjusting scanner magnification in the auxiliary direction (U065) When this maintenance item is performed, the settings in U065, U066 and U067 are also changed. Purpose Used to make respective auto adjustments for the scanner. Method 1. Place the specified original on the contact glass. 2. Press the start key. on appears. 3. Press the start key. Auto adjustment starts. When adjustment is complete, Gd appears. 4. Display each setting value after adjustment by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Setting value Scanner center line Scanner leading edge registration Scanner magnification in the auxiliary scanning direction
If a problem occurs during auto adjustment, nG is displayed and operation stops. Lighting the copy exposure indicator exp. 2 and then exp. 3 using the copy exposure adjustment keys will display the error code. Determine the details of the problem and either repeat the procedure from the beginning, or adjust the remaining items manually by running the corresponding maintenance items. Completion Press the stop/clear key after auto adjustment is complete. The indication for selecting a maintenance item No. appears. If the stop/clear key is pressed during auto adjustment, adjustment stops and no settings are changed.
1-4-20
Service Manual
Y102911-6
Description
Description Changes the exposure density gradient in manual density mode, depending on respective image modes (text, text and photo, photo). Purpose To set how the image density is altered by a change of one step in the manual density adjustment. Also used to make copy image darker or lighter. Start 1. Press the start key. A selection item appears. 2. Select the image mode to be adjusted by lighting image mode LEDs using the image mode selection key. Image mode LEDs Description Density in text mode
: Off,
: On
Setting 1. Select the item to be adjusted by lighting a copy exposure indicator using the copy exposure adjustment keys. 2. Adjust the setting using the zoom +/ keys. Copy exposure indicator Exp. 1 Exp. 2 Description Setting range Initial setting 0 0
Change in density when manual density is set dark 0 to 3 Change in density when manual density is set light 0 to 3
Image density Dark Setting: 3 Setting: 0
Increasing the setting makes the change in density larger, and decreasing it makes the change smaller.
Set to LIGHTER
Set to DARKER
Light Light Center Density adjustment range: Normal Density adjustment range: Special area Dark
Density adjustment
Figure 1-4-5 Exposure density gradient 3. Press the start key. The value is set. Test copy mode While this maintenance item is being performed, copying from an original can be made in test copy mode. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-21
Description
Description Displays the original width detection data and sets the original width detection threshold. Purpose To check the original width detection. Also to change the original size detection threshold if the size of the original on the contact glass is detected incorrectly. Start 1. Press the start key. A selection item appears. 2. Select the item using the zoom +/ keys. 3. Press the start key. The machine enters the execution mode. Display dA LE Description Checking the original width detection data Setting or checking the original width detection threshold
Method to display the original width detection data 1. Place an original on the contact glass and turn the original detection switch on. The exposure lamp turns on and the width of the original is detected. The scanner data taken at the nine points from (1) at the machine rear to (9) at the machine front is displayed. The data is displayed within the range of 000 to 255, 000 indicating white (original present) and 255 indicating black (no original). 2. Change the point to display the detection data by lighting a copy exposure indicator or making one flash using the copy exposure adjustment keys. For the correspondence between the detection point and the copy exposure indicators, see Figure 1-4-6.
1 4 7
Point 1 2 3 4 5
2 5 8
3 6 9
Point 6 7 8 9 Copy exposure indicator exp. 1 (flashing) exp. 2 (flashing) exp. 3 (flashing) exp. 4 (flashing)
Copy exposure indicator exp. 1 (lit) exp. 2 (lit) exp. 3 (lit) exp. 4 (lit) exp. 5 (lit)
Figure 1-4-6 3. Press the stop/clear key. The selected item appears.
1-4-22
Service Manual
Y102911-6
Maintenance Description item No. U099 Method to set or check the original size detection threshold (cont.) 1. Place an original on the contact glass and turn the original detection switch on. The original size detection starts and detection data is displayed. 2. Change the detection item by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Exp. 4 Description Scanner data threshold Time between original detection switch turning on and reading-in of scanner data Detected original width Original size detected by scanner data and original size sensor detection data * See Paper size in U073 for the paper size for each setting. 3. To change the original size detection threshold, light exp. 1 or 2 and change the setting using the zoom +/ keys. 4. Press the start key. The value is set. 5. Press the stop/clear key. The selected item appears. Completion Press the stop/clear key while a selection item is displayed. The indication for selecting a maintenance item No. appears. U100 Setting the main high voltage Description Changes the surface potential by changing the grid control voltage. Also performs main charging. Also changes the setting of main charging copy quantity correction. Purpose To set the surface potential or check main charging. Also used when reentering data after initializing the set data. Start 1. Press the start key. A selection item appears. 2. Select the item using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 5 (lit) Exp. 1 (flashing) Description Changing the grid control voltage Turning the main charger on Turning the main charger on and the laser scanner unit on and off Main charging copy quantity correction, copy interval Main charging copy quantity correction, copy quantity Main charging copy quantity correction, correction amount Data range 0 to 255 0 to 100 ms 0 to 350 mm 0 to 63* Remarks Adjustable Adjustable Initial setting 170 50
Method for main charger output 1. Press the start key. The selected operation starts. 2. To stop operation, press the stop/clear key. Setting the grid control voltage 1. Change the setting using the zoom +/ keys. Description Grid control voltage Setting range 0 to 255 Initial setting 135
Increasing the setting makes the surface potential higher, and decreasing it makes the potential lower. Change in value per step: approximately 3.6 V 2. Press the start key. The value is set.
Y102911-6
Service Manual
1-4-23
Maintenance Description item No. U100 Setting the main charging copy quantity correction (cont.) 1. Change the setting using the zoom +/ keys. Display Exp. 4 (lit) Exp. 5 (lit) Exp. 1 (flashing) Setting Copy interval Copy quantity Correction amount Setting range 1 to 255 (minute) 1 to 255 (10 sheets) 0 to 50 (bit) Initial setting 60 50 10
* Copy interval: Sets the time interval from the previous copying. If the time from the previous copying exceeds this preset value, the copy quantity counter will be reset. Copy quantity: Sets the copy quantity from which copy quantity correction starts. When the copy quantity counter reaches this preset value, correction will start. Correction amount: Sets the correction amount for copy quantity correction. * Set the values in the range from 5 to 120 minutes for copy interval, from 10 to 2,000 sheets for copy quantity, and from 5 to 50 bits for correction amount. 2. Press the start key. The value is set. Completion Press the stop/clear key when main charger output stops while a selection item is displayed. The indication for selecting a maintenance item No. appears. U101 Setting the other high voltages Description Changes the developing bias clock, the transfer and separation charging output timing. Purpose To check the developing bias clock, the transfer and separation charging output timing. Do not change the preset value. Method Press the start key. A selection item appears. Setting 1. Select the group to be set or checked by lighting image mode LEDs using the image mode selection key. 2. Select the item to be set by lighting a copy exposure indicator using the copy exposure adjustment keys. Image mode LED Copy exposure indicator Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 5 (lit) Exp. 1 (flashing) Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Description Developing bias clock frequency Developing bias clock duty Transfer control voltage (large size) Transfer control voltage (small size) Transfer charging output OFF timing Transfer charging output ON timing Setting range 2 to 255 1 to 99 0 to 255 0 to 255 0 to 255 0 to 255 Initial setting 27 45 168 179 38 34 1 33 43
Separation control voltage 0 to 255 Separation charging output ON timing 0 to 255 Separation charging output OFF timing 0 to 255
3. Change the setting using the zoom +/ keys. 4. Press the start key. The value is set. Completion Press the stop/clear key while a selection item is displayed. The indication for selecting a maintenance item No. appears.
1-4-24
Service Manual
Y102911-6
Description
Description Displays the drum counts for checking, clearing or changing a figure. Purpose To check the drum status. Also used to clear the count after replacing the drum during regular maintenance. Since the count was cleared before shipping, do not clear it when installing. A drum count value less than 150K, however, cannot be cleared. Method 1. Press the start key. 2. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Description First 3 digits Last 3 digits Clearing the count Setting range 000 to 999 000 to 999 Initial setting 000 000
Clearing 1. Light exp. 3. 2. Press the start key. The count is cleared, and the indication for selecting a maintenance item No. appears. Setting 1. Change the count using the numeric or zoom +/ keys. 2. Press the start key. The count is set, and the indication for selecting a maintenance item No. appears. Completion To exit the maintenance mode without changing the count, press the stop/clear key. The indication for selecting a maintenance item No. appears. U130 Toner install mode Description Executes toner install operation. Purpose To operate when installing the machine. Method 1. Press the start key. on appears. 2. Press the start key. * Installation of toner starts and "9" is indicated in the copy quantity display. Each time one minute elapses, the indicated value decrements. When the installation is complete, "Gd" will be displayed if the installation is successful or "nG" will be displayed if it has failed. 3. To stop the installation in the middle, press the stop/clear key. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-25
Maintenance item No. U144 Setting toner loading operation Description Sets toner loading operation.
Description
Purpose To run when drum filming (background blur in paper edge section) occurs. Change the setting value to 3 when poor-quality paper is used and filming occurs frequently. Method Press the start key. The screen for selecting an item is displayed. Setting 1. Change the setting using the zoom +/ keys. Display 0 1 2 3 Description Toner not loaded Executes toner loading operation before starting driving based on the printing ratio. Executes toner loading operation between sheets of paper based on the printing ratio. Executes toner loading operation between sheets of paper every time.
Initial setting: 0 2. Press the start key. The value is set. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U158 Checking/clearing the developing count Description Displays the developing count for checking, clearing or changing a figure. Purpose To check the developing count. Method 1. Press the start key. 2. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Description First 3 digits Last 3 digits Clearing the count Setting range 000 to 999 000 to 999 Initial setting 000 000
Clearing 1. Light exp. 3. 2. Press the start key. The count is cleared, and the indication for selecting a maintenance item No. appears. Setting 1. Change the count using the numeric or zoom +/ keys. 2. Press the start key. The count is set, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the count, press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-26
Service Manual
Y102911-6
Maintenance item No. U161 Setting the fixing control temperature Description Changes the fixing control temperature.
Description
Purpose Normally no change is necessary. However, can be used to prevent curling or creasing of paper, or solve a fixing problem on thick paper. Method Press the start key. A selection item appears. Setting 1. Select the item to be set by lighting a copy exposure indicator using the copy exposure adjustment keys. 2. Change the setting using the zoom +/ keys. Copy exposure indicator Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 5 (lit) Exp. 1 (flashing) Description Primary stabilization fixing temperature Secondary stabilization fixing temperature Copying operation temperature 1 Copying operation temperature 2 Number of sheets for fixing control Number of sheets for fixing control (thick paper) Setting range 120 to 185 (C) 120 to 185 (C) 160 to 220 (C) 160 to 220 (C) 1 to 99 1 to 99 Initial setting 140 160 170 180 5 20
Copying operation temperature 1: Temperature in copying operation at the start of copying Copying operation temperature 2: Temperature in copying operation after the specified number of sheets for fixing control have passed Number of sheets for fixing control: The number of sheets to be counted for switching from copying operation temperature 1 to copying operation temperature 2 The temperatures are to be set such that Secondary stabilization > Primary stabilization. = 3. Press the start key. The value is set. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears. U162 Stabilizing fixing forcibly Description Stops the stabilization fixing drive forcibly, regardless of fixing temperature. Purpose To forcibly stabilize the machine before the fixing section reaches stabilization temperature. Method 1. Press the start key. on appears. 2. Press the start key. The forced stabilization mode is entered, and stabilization operation stops regardless of fixing temperature. The indication for selecting a maintenance item No. appears. To exit the forced stabilization mode, turn the power off and on. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U163 Resetting the fixing problem data Description Resets the detection of a service call code indicating a problem in the fixing section. Purpose To prevent accidents due to an abnormally high fixing temperature. Method 1. Press the start key. CLE appears. 2. Press the start key. The fixing problem data is initialized. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-27
Description
Description Displays the fixing count for checking, clearing or changing a figure. Purpose To check the fixing count. Method 1. Press the start key. 2. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Description First 3 digits Last 3 digits Clearing the count Setting range 000 to 999 000 to 999 Initial setting 000 000
Clearing 1. Light exp. 3. 2. Press the start key. The count is cleared, and the indication for selecting a maintenance item No. appears. Setting 1. Change the count using the numeric or zoom +/ keys. 2. Press the start key. The count is set, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the count, press the stop/clear key. The indication for selecting a maintenance item No. appears. U199 Checking the fixing temperature Description Displays the fixing temperature and the ambient temperature. Purpose To check the fixing temperature and the ambient temperature. Method 1. Press the start key. 2. Display each temperature by lighting the respective copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Description Fixing temperature (C) Ambient temperature (C)
Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U200 Turning all LEDs on Description Turns all the LEDs on the operation panel on. Purpose To check if all the LEDs on the operation panel light. Method Press the start key. All the LEDs on the operation panel light. Press the stop/clear key or wait for 10 s. The LEDs turns off, and the indication for selecting a maintenance item No. appears. U202 Setting the KMAS host monitoring system Description Initializes or operates the KMAS host monitoring system. This is an optional device which is currently supported only by Japanese specification machines, so no setting is necessary.
1-4-28
Service Manual
Y102911-6
Description
Description Simulates the original conveying operation separately in the DP. Purpose To check the DP. Method 1. Press the start key. 2. Place an original in the DP if running this simulation with paper. 3. Select the item to be operated using the copy exposure adjustment keys. Display (copy exposure indicator) d-P (exp. 1) d-n (exp. 2) dp2 (exp. 3) dn2 (exp. 4) Operation With paper Without paper (continuous operation) With paper (duplex mode) Without paper (duplex mode)
4. Press the start key. The operation starts. 5. To stop continuous operation, press the stop/clear key. Completion Press the stop/clear key when the operation stops. The indication for selecting a maintenance item No. appears. U204 Setting the presence or absence of a key card or key counter Description Sets the presence or absence of the optional key card or key counter. Purpose To run this maintenance item if a key card or key counter is installed. Method Press the start key. Setting 1. Select either on or oFF using the zoom +/ keys. Display oFF on Description None The key card or key counter is installed
Initial setting: oFF 2. Press the start key. The setting is set and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears. U207 Checking the operation panel keys Description Checks operation of the operation panel keys. Purpose To check operation of all the keys and LEDs on the operation panel. Method 1. Press the start key. 2. 1 appears on the copy quantity display and the leftmost LED on the operation panel lights. 3. As the keys on the operation panel are pressed in order from the left to right, the figure shown on the copy quantity display increases in increments of 1. If there is an LED corresponding to the key pressed, the LED will light. 4. When all the keys on the operation panel have been pressed, all the LEDs light for up to 10 seconds. 5. When the LEDs go off, press the start key. All the LEDs light for 10 seconds again. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-29
Maintenance Description item No. U243 Checking the operation of the DP motors and solenoids Description Turns the motors and solenoids in the optional DP on. Purpose To check the operation of the DP motors and solenoids. Method 1. Press the start key. 2. Select the motor or solenoid to be operated using the copy exposure adjustment keys. 3. Press the start key. The operation starts. Indication (copy exposure indicator) F-0 (exp. 1) C-0 (exp. 2) b-S (exp. 3) P-S (exp. 4) Motor Original feed motor (OFM) Original conveying motor (OCM) Switchback feedshift solenoid (SBFSSOL) Switchback pressure solenoid (SBPSOL)
4. To turn each motor off, press the stop/clear key. Completion Press the stop/clear key when operation stops. The indication for selecting a maintenance item No. appears. U244 Checking the DP switches Description Displays the status of the switches in the optional DP. Purpose To check if switches in the DP operate correctly. Method 1. Press the start key. 2. Turn each switche on and off manually to check the status. When the on-status of a switch is detected, the LEDs on the operation panel corresponding to the operated switch lights. LEDs Auto Exp. Text & Photo Photo Text Program Eco-copy Switch Original set switch (OSSW) DP timing switch (DPTSW) Original detection switch (ODSW) DP original cover switch (DPOCSW) Original size length switch (OSLSW) Original switchback switch (OSBSW)
Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U250 Setting the maintenance cycle Description Displays and changes the maintenance cycle. Purpose To check and change the maintenance cycle. Method 1. Press the start key. The current setting is displayed. 2. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Description First 3 digits Last 3 digits Setting range 000 to 999 000 to 999 Initial setting 150 000
3. Change the setting using the numeric or zoom +/ keys. 4. Press the start key. The value is set, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-30
Service Manual
Y102911-6
Description
Description Displays, clears and changes the maintenance count. Purpose To check the maintenance count. Also to clear the count during maintenance service. Method 1. Press the start key. 2. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Description First 3 digits Last 3 digits Clearing the count Setting range 000 to 999 000 to 999 Initial setting 000 000
Clearing 1. Light exp. 3. 2. Press the start key. The count is cleared, and the indication for selecting a maintenance item No. appears. Setting 1. Change the count using the numeric or zoom +/ keys. 2. Press the start key. The count is set, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the count, press the stop/clear key. The indication for selecting a maintenance item No. appears. U252 Setting the destination Description Switches the operations and screens of the machine according to the destination. Purpose To return the destination setting to its default setting after initializing the backup RAM by running maintenance item U020. Method Press the start key. Setting 1. Select the destination using the zoom +/ keys. Display Jpn Inc EUP ASA Description Metric (Japan) specifications Inch (North America) specifications Metric (Europe) specifications Metric (Asia Pacific) specifications
2. Press the start key. The setting is set, and the machine automatically returns to the same status as when the power is turned on. Completion To exit this maintenance item without changing the current count, press the stop/clear key. The indication for selecting a maintenance item No. appears. Supplement The specified initial settings are provided according to the destinations in the maintenance items below. To change the initial settings in those items, be sure to run maintenance item U021 after changing the destination. Initial setting according to the destinations Maintenance Title item No. 253 255 Switching between double and single counts Setting auto clear time Japan Single 120 s Inch Double 90 s Europe Metric, Asia Pacific Double 90 s
Y102911-6
Service Manual
1-4-31
Maintenance Description item No. U253 Switching between double and single counts Description Switches the count system for the total counter and other counters. Purpose According to user (copy service provider) request, select if A3/11" 17" paper is to be counted as one sheet (single count) or two sheets (double count). Method Press the start key. Setting 1. Select the item using the zoom +/ keys. Display -A3 Sin -b4 Description Double count for A3/11" 17" paper only Single count for all size paper Double count for B4 size or larger
Initial setting: -A3 2. Press the start key. The setting is set, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears. U254 Turning auto start function on/off Description Selects if the auto start function is turned on. Purpose Normally no change is necessary. If incorrect operation occurs, turn the function off: this may solve the problem. Method Press the start key. Setting 1. Select either on or oFF using the zoom +/ keys. Display on oFF Description Auto start function on Auto start function off
Initial setting: on 2. Press the start key. The setting is set, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-32
Service Manual
Y102911-6
Description
Description Sets the time to return to initial settings after copying is complete. Purpose To be set according to frequency of use. Set to a comparatively long time for continuous copying at the same settings, and a comparatively short time for frequent copying at various settings. Method Press the start key. The current setting is displayed. Setting 1. Change the setting using the zoom +/ keys. Description Auto clear time Setting range 0 to 270 (s) Initial setting 90
The setting can be changed by 10 s per step. When set to 0, the auto clear function is cancelled. 2. Press the start key. The value is set, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears. U258 Switching copy operation at toner empty detection Description Selects if continuous copying is enabled after toner empty is detected. Method Press the start key. The current setting is displayed. Setting 1. Select single or continuous copying using the zoom +/ keys. Display Sin Con Description Enables only single copying. Enables single and continuous copying.
Initial setting: Sin 2. Press the start key. The setting is set, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-33
Description
Description Changes the copy count timing for the total counter and other counters. Purpose To be set according to user (copy service provider) request. If a paper jam occurs frequently in the eject section when the number of copies is counted at the time of paper ejection, copies are provided without copy counts. The copy service provider cannot charge for such copying. To prevent this, the copy timing should be made earlier. If a paper jam occurs frequently in the paper conveying or fixing sections when the number of copies is counted before the paper reaches those sections, copying is charged without a copy being made. To prevent this, the copy timing should be made later. Method Press the start key. Setting 1. Select the copy count timing using the zoom +/ keys. Display FEd EJE Description When secondary paper feed starts When the paper is ejected
Initial setting: EJE 2. Press the start key. The setting is set, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears. U265 Setting the destination specifications Description Sets whether or not to print the product name on the reports that users print. Purpose To be set according to user request. Method Press the start key. The current setting appears. Setting 1. Enter 0 or 2 using the zoom +/ keys. Setting 0 2 Description Product name printed Product name not printed
Initial setting: 0 2. Press the start key. The setting is set. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-34
Service Manual
Y102911-6
Description
Description Sets the coefficient of nonstandard sizes in relation to the A4/11" 81/2" size. The coefficient set here is used to convert the black ratio in relation to the A4/11" 81/2" size and to display the result in user simulation. Purpose To set the coefficient for converting the black ratio for nonstandard sizes in relation to the A4/11" 81/2" size for copying and printing respectively. Method Press the start key. The current setting is displayed. Setting 1. Change the setting using the zoom +/ keys. Description Size conversion factor Setting range 0.0 to 3.0 Initial setting 1.0
2. Press the start key. The value is set, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears. U342 Setting the ejection restriction Description Sets or cancels the restriction on the number of sheets to be ejected continuously. When the restriction is set, the number of sheets that can be ejected continuously to the internal eject tray will be limited to 250. Purpose According to user request, sets or cancels restriction on the number of sheets. Method Press the start key. Setting 1. Select on or oFF using the zoom +/ keys. Display on oFF Description The number of sheets restricted. The number of sheets not restricted.
Initial setting: on 2. Press the start key. The setting is set. The indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the current setting, press the stop/clear key. The indication for selecting a maintenance item No. appears. U345 Setting the value for maintenance due indication Description Sets when to display a message notifying that the time for maintenance is about to be reached, by setting the number of copies that can be made before the current maintenance cycle ends. When the difference between the number of copies of the maintenance cycle and that of the maintenance count reaches the set value, the message is displayed. This maintenance mode is effective for only Japanese specification.
Y102911-6
Service Manual
1-4-35
Maintenance item No. U402 Adjusting margins of image printing Adjustment See page 1-6-15. U403
Description
Adjusting margins for scanning an original on the contact glass Adjustment See page 1-6-32.
U404
Adjusting margins for scanning an original from the DP Description Adjusts margins for scanning the original from the DP. Purpose Used if margins are not correct when the optional DP is used. Caution Before making this adjustment, ensure that the following adjustments have been made in maintenance mode.
U402
U403
U404
Method Press the start key. Setting 1. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. 2. Change the setting using the zoom +/ keys. Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Exp. 4 Description Left margin Leading edge margin Right margin Trailing edge margin Setting range 0.0 to 10.0 0.0 to 10.0 0.0 to 10.0 0.0 to 10.0 Initial setting 2.0 3.0 2.0 2.0 Change in value per step 0.5 mm 0.5 mm 0.5 mm 0.5 mm
Increasing the setting makes the margin wider, and decreasing it makes the margin narrower.
DP leading edge margin (3 2.5 mm) Ejection direction (reference)
Figure 1-4-7 Correct margin amount 3. Press the start key. The value is set. Interrupt copy mode While this maintenance item is being performed, copying from an original can be made in interrupt copy mode. A test copy is output at the reduction ratio of 95%. Completion Press the stop/clear key while a selection item is displayed. The indication for selecting a maintenance item No. appears. U407 Adjusting the leading edge registration for memory image printing Adjustment See page 1-6-13.
1-4-36
Service Manual
Y102911-6
Maintenance Description item No. U901 Checking/clearing copy counts by paper feed locations
Description Displays or clears copy counts by paper feed locations. Purpose To check the time to replace consumable parts. Also to clear the counts after replacing the consumable parts. Method 1. Press the start key. 2. Select the paper feed location (group No.) for which the count is to be checked or cleared by lighting image mode LEDs using the image mode selection key. 3. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. Image mode LED (group No.) 1 Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Exp. 1 Exp. 2 Exp. 3 Exp. 1 Exp. 2 Exp. 3 Exp. 1 Exp. 2 Exp. 3 Exp. 1 Exp. 2 Exp. 3 Exp. 1 Exp. 2 Exp. 3 Exp. 1 Copy quantity display (count value) First 3 digits of bypass copy count Last 3 digits of bypass copy count Clearing the count (CLE) First 3 digits of the drawer copy count Last 3 digits of the drawer copy count Clearing the count (CLE) First 3 digits of the first paper feeder copy count Last 3 digits of the first paper feeder copy count Clearing the count (CLE) First 3 digits of the second paper feeder copy count Last 3 digits of the second paper feeder copy count Clearing the count (CLE) First 3 digits of the third paper feeder copy count Last 3 digits of the third paper feeder copy count Clearing the count (CLE) First 3 digits of the duplex unit copy count Last 3 digits of the duplex unit copy count Clearing the count (CLE) Clearing all counts (CLE)
: Off, : On, : Flashing Note: When no optional paper feed device is installed, the counts corresponding to optional paper feed devices will not appear.
Clearing copy counts by paper feed locations 1. Select the paper feed location to clear the count. 2. Light exp. 3 using the copy exposure adjustment key. 3. Press the start key. The count is cleared. Clearing copy counts for all paper feed locations 1. Select group 7. 2. Press the start key. The counts are cleared. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-37
Description
Description Displays or clears the jam counts by jam locations. Purpose To check the paper jam status. Also to clear the jam counts after replacing consumable parts. Method 1. Press the start key. 2. Display the jam code to check the count using the copy exposure adjustment keys. 3. Press the start key. The jam count appears. If the jam count is a 4-digit value, the first digit and the last 3 digits are displayed alternately. 4. Press the stop/clear key. The jam code appears again.
Copy exposure adjustment keys Start key Stop/ Copy exposure clear key adjustment keys Copy exposure adjustment keys Start key
J10
Stop/ clear key
J11
CLE
10
100
Figure 1-4-8 Clearing all jam counts 1. Display CLE using the copy exposure adjustment keys. Jam counts cannot be cleared individually. 2. Press the start key. The counts are cleared. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U904 Checking/clearing the service call counts Description Displays or clears the service call code counts by types. Purpose To check the service call code status by types. Also to clear the service call code counts after replacing consumable parts. Method 1. Press the start key. 2. Display the service call code to check the count using the copy exposure adjustment keys. 3. Press the start key. The service call count appears. If the service call count is a 4-digit value, the first digit and the last 3 digits are displayed alternately. 4. Press the stop/clear key. The service call code appears again.
Copy exposure adjustment keys Start key Stop/ Copy exposure clear key adjustment keys Copy exposure adjustment keys Start key
010
Stop/ clear key
011
CLE
10
100
Figure 1-4-9 Clearing counts by service call codes 1. Display the service call code to clear the count. 2. Press the reset key. The count is cleared. Clearing all service call counts 1. Display CLE using the copy exposure adjustment keys. 2. Press the start key. The counts are cleared. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-38
Service Manual
Y102911-6
Maintenance item No. U905 Checking/clearing counts by the DP Description Displays or clears the counts of the DP.
Description
Purpose To check the use of the DP. Also to clear the counts after replacing consumable parts. Method 1. Press the start key. 2. Select the count (group No.) to be checked or cleared by lighting image mode LEDs using the image mode selection key. 3. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. Image mode LED (group No.) 1 Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 2 Exp. 1 Exp. 2 Exp. 3
: Off,
: On
Copy quantity display (count value) First 3 digits of the number of original replacement Last 3 digits of the number of original replacement Clearing the count (CLE) First 3 digits of the double-sided original feed count Last 3 digits of the double-sided original feed count Clearing the count (CLE)
Clearing 1. Select the count to be cleared. 2. Light exp. 3 using the copy exposure adjustment keys. 3. Press the start key. The count is cleared. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-39
Maintenance item No. U908 Checking the total count Description Display the total count value. Purpose To check the total count value.
Description
Method 1. Press the start key. 2. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Copy quantity display (count value) First 3 digits of the total count Last 3 digits of the total count
Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U910 Clearing the black ratio data Description Clears the accumulated black ratio data for A4/11" 81/2" sheets. Purpose To clear data as required at times such as during maintenance service. Method 1. Press the start key. 2. Select on using the zoom +/ keys. Display on Operation Canceling the clearing Executing the clearing
3. Press the start key. The accumulated black ratio data is cleared. Completion To exit this maintenance item without clearing the data, press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-40
Service Manual
Y102911-6
Maintenance Description item No. U911 Checking/clearing copy counts by paper size Description Displays or clears the paper feed count value by paper size. Purpose To check the time to replace consumable parts. Also to clear the counts after replacing the consumable parts. Method 1. Press the start key. 2. Select the paper size (group No.) for which the count is to be checked or cleared by lighting image mode LEDs using the image mode selection key. 3. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys.
Image mode LED (group No.) 1 Copy exposure indicator Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) 3 Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) 7 Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) : Off : On : Flashing Copy quantity display (count value) -A3 display the A3 size First 3 digits of A3 size copy count Last 3 digits of A3 size copy count Clearing the count (CLE) -b4 display the B4 size First 3 digits of B4 size copy count Last 3 digits of B4 size copy count Clearing the count (CLE) -A4 display the A4 size First 3 digits of A4 size copy count Last 3 digits of A4 size copy count Clearing the count (CLE) -b5 display the B5 size First 3 digits of FOLIO size copy count Last 3 digits of FOLIO size copy count Clearing the count (CLE) -A5 display the A5 size First 3 digits of Legal size copy count Last 3 digits of Legal size copy count Clearing the count (CLE) -A6 display the A6 size First 3 digits of Letter size copy count Last 3 digits of Letter size copy count Clearing the count (CLE) -Fo display the FOLIO size First 3 digits of FOLIO size copy count Last 3 digits of FOLIO size copy count Clearing the count (CLE) -Ld display the Ledger size First 3 digits of Ledger size copy count Last 3 digits of Ledger size copy count Clearing the count (CLE)
Y102911-6
Service Manual
1-4-41
Maintenance item No. U911 Image mode LED (group No.) 9 Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) 11 Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) 12 Exp. 1 (lit) Exp. 2 (lit) Exp. 3 (lit) Exp. 4 (lit) Exp. 1 (lit)
Description
Copy quantity display (count value) -Lg display the Legal size First 3 digits of Legal size copy count Last 3 digits of Legal size copy count Clearing the count (CLE) -Lt display the Letter size First 3 digits of Letter size copy count Last 3 digits of Letter size copy count Clearing the count (CLE) -St display the Statement size First 3 digits of Statement size copy count Last 3 digits of Statement size copy count Clearing the count (CLE) -ot display the other size First 3 digits of other size copy count Last 3 digits of other size copy count Clearing the count (CLE) Clearing all counts (CLE)
10
13
: Off
: On
: Flashing
Clearing copy counts by paper size 1. Select the paper size to clear the count. 2. Display CLE using the copy exposure adjustment keys. 3. Press the start key. The count is cleared. Clearing copy counts for all paper size 1. Select group 13. 2. Press the start key. The counts are cleared. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U927 Clearing accounting counter Description Clears the total count and the scanner count. The counts, however, can be cleared only one time. If either of the total count or the scanner count exceeds 1,000, this mode cannot be run. Purpose To start the counters with value 0 when installing the machine. Method 1. Press the start key. If the counters have been already cleared or either of the total counter or the scanner counter exceeds 1,000, this mode cannot be run and nG is displayed. 2. Select on using the zoom +/ keys. Display on Operation Canceling the clearing Executing the clearing
3. Press the start key. The accounting counter is cleared. Completion To exit this maintenance item without clearing the data, press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-42
Service Manual
Y102911-6
Description
Description Displays the machine life counts for checking a figure. Purpose To check machine status. Do not clear or change the preset value. Method 1. Press the start key. 2. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Description First 3 digits Last 3 digits Clearing the count Setting range 000 to 999 000 to 999 Initial setting 000 000
Clearing 1. Light exp. 3. 2. Press the start key. The count is cleared, and the indication for selecting a maintenance item No. appears. Setting 1. Change the count using the numeric or zoom +/ keys. 2. Press the start key. The count is set, and the indication for selecting a maintenance item No. appears. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U990 Checking/clearing the time for the exposure lamp to light Description Displays or clears the accumulated time for the exposure lamp to light. Purpose To check duration of use of the exposure lamp. Also to clear the accumulated time for the lamp after replacement. Method 1. Press the start key. 2. Select the item by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Exp. 3 Copy quantity display First 3 digits of the lamp-on time (minutes) Last 3 digits of the lamp-on time (minutes) Clearing the lamp-on time (CLE)
Clearing 1. Light exp. 3. 2. Press the start key. The accumulated time is cleared, and the indication for selecting a maintenance item No. appears. Completion To exit this maintenance item without changing the accumulated time, press the stop/clear key. The indication for selecting a maintenance item No. appears.
Y102911-6
Service Manual
1-4-43
Maintenance item No. U991 Checking the scanner count Description Display the scanner count value. Purpose To check the scanner count value.
Description
Method 1. Press the start key. 2. Change the indication of the copy quantity display by lighting a copy exposure indicator using the copy exposure adjustment keys. Copy exposure indicator Exp. 1 Exp. 2 Copy quantity display (count value) First 3 digits of the scanner count Last 3 digits of the scanner count
Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears. U993 Outputting a VTC-PG pattern Description Selects and outputs a VTC-PG pattern created in the copier. Purpose When performing respective image printing adjustments, used to check the machine status apart from that of the scanner with a non-scanned output VTC-PG pattern. Method 1. Press the start key. 2. Select the VTC-PG pattern to be output using the copy exposure adjustment keys. Display 0 PG pattern to be output Purpose Center line adjustment
3. Press the interrupt key. The machine enters the PG pattern output mode. 4. Press the start key. A VTC-PG pattern is output. Completion Press the stop/clear key. The indication for selecting a maintenance item No. appears.
1-4-44
Service Manual
Y102911-6
Press both of the copy exposure adjustment keys and manegement key for 3 s.
End
Y102911-6
Service Manual
1-4-45
(2) Setting department management items Management on/off setting 1. Select d01 and press the enter key. 2. Select ON or OFF and press the enter key. Setting range: ON (set)/OFF (no setting) Management code registration 1. Select d02 and press the enter key. 2. Enter a department code using the numeric keys and press the enter key. Setting range: 0 to 99999999 Management code deletion 1. Select d03 and press the enter key. 2. Enter the department code to be deleted using the numeric keys 3. Select YES or NO and press the enter key. Setting range: YES (delete)/NO (no deletion) Clearing management count 1. Select d04 and press the enter key. 2. Select YES or NO and press the enter key. Setting range: YES (clear)/NO (do not clear) Outputing the management list 1. Select d05 and press the enter key. If A4/11" 81/2" paper is present, the list is automatically printed out. Otherwise, select the paper source and press the start key.
(3) Copy default User status report Prints the details of the default settings. 1. Select F01 and press the enter key. If A4/11" 81/2" paper is present, the list is automatically printed out. Otherwise, select the paper source and press the start key. Original image quality Selects the image quality at power-on. 1. Select F02 and press the enter key. 2. Select the image mode and press the enter key. Setting range: 1 (text & photo)/2 (photo)/ 3 (text) Exposure mode Selects the exposure mode at power-on. 1. Select F03 and press the enter key. 2. Select the exposure mode and press the enter key. Setting range: 1 (manual)/2 (auto) Eco-copy Selects the eco-copy mode at power-on. 1. Select F04 and press the enter key. 2. Select ON or OFF and press the enter key. Setting range: ON (enabled)/OFF (disabled) Exposure steps Sets the number of exposure steps for the manual exposure mode. 1. Select F05 and press the enter key. 2. Select 1 step or 0.5 step and press the enter key. Setting range: 1 (1 step)/2 (0.5 step) Auto exposure adjustment Adjusts the exposure for the auto exposure mode. 1. Select F06 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 (lightest) to 7 (darkest) Text and photo mode exposure adjustment Adjusts the exposure to be used when text and photo original is selected for the image mode. 1. Select F07 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 (lightest) to 7 (darkest) Photo exposure adjustment Adjusts the exposure to be used when photo original is selected for the image mode. 1. Select F08 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 (lightest) to 7 (darkest) Text exposure adjustment Adjusts the exposure to be used when text original is selected for the image mode. 1. Select F09 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 (lightest) to 7 (darkest) Black-line correction Reduces black lines that may be caused when the DP is used. 1. Select F10 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 (off)/2 (weak)/3 (strong)
1-4-46
Service Manual
Y102911-6
Photo processing Select the image processing method for photo originals. 1. Select F11 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 (error diffusion)/2 (dithering) Setting this to error diffusion when copying originals with text and photo and dithering when copying originals with mainly photos. Ground color adjustment The ground color adjusting after copying. 1. Select F12 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 (lightest) to 5 (darkest) Paper selection Select the auto paper select function based on the original size or priority cassette selection. 1. Select F13 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 (auto paper selection)/ 2 (selected drawer) Selected drawer Selects the drawer that is to be automatically be given priority for use. 1. Select F14 and press the enter key. 2. Select the default drawer and press the enter key. Setting range: 1 (drawer)/2 (first paper feeder)/ 3 (second paper feeder)/4 (third paper feeder) Note: This setting item will not be displayed if no optional paper feeder is installed. Auto drawer switching Sets whether the auto drawer switching function is available. 1. Select F15 and press the enter key. 2. Select ON or OFF and press the enter key. Setting range: ON (enabled)/OFF (disabled) Note: This setting item will not be displayed if no optional paper feeder is installed. AMS mode Selects whether auto magnification selection or 100% magnification is to be given priority when the sizes of the original and copy paper are different. 1. Select F16 and press the enter key. 2. Select ON or OFF and press the enter key. Setting range: ON (enabled)/OFF (disabled) Drawer paper size (drawer 1) Sets the paper size for the drawer so that it will be automatically selected. 1. Select F17 and press the enter key. 2. Select the paper size and press the enter key. Setting range: AtC (auto detection metric)/ AtI (auto detection inch)/o2r (oficio2)
Drawer paper size (drawer 2) Sets the paper size for the first paper feeder so that it will be automatically selected. 1. Select F18 and press the enter key. 2. Select the paper size and press the enter key. Setting range: AtC (auto detection metric)/ AtI (auto detection inch)/o2r (oficio2) Note: This setting item will not be displayed if no optional paper feeder is installed. Drawer paper size (drawer 3) Sets the paper size for the second paper feeder so that it will be automatically selected. 1. Select F19 and press the enter key. 2. Select the paper size and press the enter key. Setting range: AtC (auto detection metric)/ AtI (auto detection inch)/o2r (oficio2) Note: This setting item will not be displayed if no optional paper feeder is installed. Drawer paper size (drawer 4) Sets the paper size for the third paper feeder so that it will be automatically selected. 1. Select F20 and press the enter key. 2. Select the paper size and press the enter key. Setting range: AtC (auto detection metric)/ AtI (auto detection inch)/o2r (oficio2) Note: This setting item will not be displayed if no optional paper feeder is installed. Bypass tray paper size Sets the paper size for the bypass tray so that it will be automatically selected. 1. Select F21 and press the enter key. 2. Select the paper size and press the enter key. Setting range: Uni (universal size)/A3r (A3/ 11" 17")/A4r (A4/81/2" 11")/A4E (A4 vertical/11" 81/2")/A5r (A5/51/2" 81/2")/ b4r (B4/81/2" 14")/b5r (B5)/Cu1 (custom 1)/ Cu2 (custom 2) Custom 1 size Sets the size of the paper to be set to the custom 1 size. 1. Select F22 and press the enter key. 2. Select the paper size and press the enter key. Setting range: b6r (B6)/A6r (A6)/Pos (postcard)/Ldr (ledger/11" 17")/Lgr (legal/ 81/2" 14")/Ltr (letter/81/2" 11")/LtE (letter vertical/11" 81/2")/Str (statement)/o2r (oficio2)/CPF (11" 15")/InP (irregular size)
Y102911-6
Service Manual
1-4-47
Custom 2 size Sets the size of the paper to be set to the custom 2 size. 1. Select F23 and press the enter key. 2. Select the paper size and press the enter key. Setting range: b6r (B6)/A6r (A6)/Pos (postcard)/Ldr (ledger/11" 17")/Lgr (legal/ 81/2" 14")/Ltr (letter/81/2" 11")/LtE (letter vertical/11" 81/2")/Str (statement)/o2r (oficio2)/CPF (11" 15")/InP (irregular size) Copy limit Sets the number of copies limit for multiple copying. 1. Select F24 and press the enter key. 2. Enter the setting and press the enter key. Setting range: 1 to 250 copies Duplex copy reverse-side rotation setting Select whether or not the image on the reverse side is rotated 180 degrees in the duplex copy mode. 1. Select F25 and press the enter key. 2. Select ON or OFF and press the enter key. Setting range: ON (rotate)/OFF (no rotation) Margin width Sets the default setting of the margin width for the margin copying. 1. Select F26 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 to 18 mm Border erase width Sets the default setting of the border erase width for the border erase mode. 1. Select F27 and press the enter key. 2. Select the setting and press the enter key. Setting range: 6 mm/12 mm/18 mm 4 in 1 layout setting Sets the layoout for the order in which the originals will appear in the 4 in 1 layout mode. 1. Select F28 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 to 4 Aggregate copy borderline Selects the type of borderline to be usedf in the layout mode. 1. Select F29 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 (no borderline)/2 (solid line)/ 3 (dotted line) Rotate sort Sets whether or not to perform rotate sorting when the sort mode is selected. 1. Select F30 and press the enter key. 2. Select ON or OFF and press the enter key. Setting range: ON (enabled)/OFF (disabled)
Silent mode transition time Set the silent mode transition time after copying. 1. Select F31 and press the enter key. 2. Select the setting and press the enter key. Setting range: 0 sec/5 sec/10 sec/ 15 sec/30 sec Auto clear setting Sets whether the auto clear function is available. 1. Select F32 and press the enter key. 2. Select ON or OFF and press the enter key. Setting range: ON (enabled)/OFF (disabled) Auto off setting Sets whether the auto off function is available. 1. Select F33 and press the enter key. 2. Select ON or OFF and press the enter key. Setting range: ON (enabled)/OFF (disabled) Auto clear time Sets the auto clear time. 1. Select F34 and press the enter key. 2. Select the setting and press the enter key. Setting range: 10 to 270 sec Auto preheat time Sets the auto preheat time. 1. Select F35 and press the enter key. 2. Select the setting and press the enter key. Setting range: 1 min/5 min/15 min/30 min/45 min/60 min/90 min/120 min/180 min/240 min Auto shutoff time Sets the auto shutoff time. 1. Select F36 and press the enter key. 2. Select the setting and press the enter key. Setting range: 15 min/30 min/45 min/60 min/ 90 min/120 min/180 min/240 min Alarm The alarm can be set to sound when errors occur. 1. Select F37 and press the enter key. 2. Select ON or OFF and press the enter key. Setting range: ON (sound alarm)/ OFF (no alarm) Toner coverage report Prints out a report that shows the number of copies made and the blackness ratio for each paper size. 1. Select F38 and press the enter key. If A4/11" 81/2" paper is present, the list is automatically printed out. Otherwise, select the paper source and press the start key.
1-4-48
Service Manual
Y102911-6
Figure 1-5-1
1 2 3 4
Misfeed in the paper feed section Misfeed in the paper conveying section Misfeed in the optional DP Misfeed in the optional paper feeder
Y102911-6
Service Manual
1-5-1
ESW
FSSW
DPFCL1 DFSW1
DPFCL2
DFSW2
DPFCL3
Figure 1-5-2
1-5-2
Service Manual
Y102911-6
Section System
Jam code 00
Conditions When the power switch is turned on, the machine detects activation of the registration switch (RSW), the exit switch (ESW) or the feedshift switch (FSSW). A cover open state is detected during copying. When the machine waits for secondary paper feed, 15 s or more have elapsed. The registration switch (RSW) does not turn on within 1680 ms of the bypass paper feed clutch (BYPPFCL) turning on; the clutch is then successively held off for 1 s and turned back on once, but the switch again fails to turn on within 1680 ms. The registration switch (RSW) does not turn on within 1254 ms of the paper feed clutch (PFCL) turning on; the clutch is then successively held off for 1 s and turned back on once, but the switch again fails to turn on within 1254 ms. The registration switch (RSW) does not turn on within 2780 ms of the drawer paper feed clutch 1 (DPFCL1)* turning on; the clutch is then successively held off for 1 s and turned back on once, but the switch again fails to turn on within 2780 ms. The drawer feed switch 1 (DFSW1)* does not turn on within 2490 ms of the drawer paper feed clutch 2 (DPFCL2)* turning on; the clutch is then successively held off for 1 s and turned back on once, but the switch again fails to turn on within 2490 ms. The drawer feed switch 2 (DFSW2)* does not turn on within 2490 ms of the drawer paper feed clutch 3 (DPFCL3)* turning on; the clutch is then successively held off for 1 s and turned back on once, but the switch again fails to turn on within 2490 ms. The registration switch (RSW) does not turn on within 2340 ms of drawer feed switch 1 (DFSW1)* turning on. The drawer feed switch 1 (DFSW1)* does not turn off within 2050 ms of drawer feed switch 2 (DFSW2)* turning on. The drawer feed switch 1 (DFSW1)* does not turn off within 2050 ms of drawer feed switch 2 (DFSW2)* turning off.
Cover open JAM Secondary paper feed timeout No paper feed from the bypass tray
11
12
13
14
15
The drawer feed switch 1 (DFSW1)* does not turn on within 2050 ms of drawer feed switch 2 (DFSW2)* turning on. The registration switch (RSW) does not turn off within 5320 ms of registration switch (RSW) turning on.
The registration switch (RSW) does not turn off within 1680 ms of bypass paper feed solenoid (BYPPFSOL) turning on.
21 Multiple sheets in the drawer 1 The registration switch (RSW) does not turn off within 5320 ms of registration switch (RSW) turning on. The registration switch (RSW) does not turn off within 1254 ms of paper feed clutch (PFCL) turning on.
*: Optional.
Y102911-6
Service Manual
1-5-3
Jam code 22
Conditions The registration switch (RSW) does not turn off within 4320 ms of registration switch (RSW) turning on. The registration switch (RSW) does not turn off within 2482 ms of drawer paper feed clutch 1 (DPFCL1)* turning on. The drawer feed switch 1 (DFSW1)* does not turn off within 5267 ms of drawer feed switch 1 (DFSW1)* turning on. The rdrawer feed switch 1 (DFSW1)* does not turn off within 2223 ms of drawer paper feed clutch 2 (DPFCL2)* turning on. The drawer feed switch 2 (DFSW2)* does not turn off within 5267 ms of drawer feed switch 2 (DFSW2)* turning on. The rdrawer feed switch 2 (DFSW2)* does not turn off within 2223 ms of drawer paper feed clutch 3 (DPFCL3)* turning on. A signal other than secondary paper feed start is received when the machine is waiting for secondary paper feed. The exit switch (ESW) does not turn on within 3020 ms of the registration motor (RM) turning on. The exit switch (ESW) does not turn off within 3020 ms of the registration switch (RSW) turning off. The exit switch (ESW) does not turn on within 3020 ms of the registration motor (RM) turning on.
23
24
30 40 50
Misfeed in registration/ transfer section Misfeed in the fixing section Misfeed in the exit section
Feedshift section
52
The feedshift switch (FSSW) does not turn on within 5320 ms of feedshift switch (FSSW) turning on. The feedshift switch (FSSW) does not turn off within 1530 ms of paper switchback. The feedshift switch (FSSW) does not turn on within 1530 ms of paper switchback.
Duplex section
60
The duplex paper conveying switch (DUPPCSW)* does not turn off within 3280 ms of the feedshift switch (FSSW) turning on. The duplex paper conveying switch (DUPPCSW)* does not turn on within 3280 ms of the feedshift switch (FSSW) turning on. The duplex paper conveying switch (DUPPCSW)* does not turn off within 3280 ms of the feedshift switch (FSSW) turning off.
61
The registration switch (RSW) does not turn on within 1760 ms of the duplex paper conveying switch (DUPPCSW)* turning on. The registration switch (RSW) does not turn off within 1760 ms of the duplex paper conveying switch (DUPPCSW)* turning off.
DP
70
No original feed*
During the primary feed of the second original in the singlesided or double-sided original mode, even if retry operation is performed five times, primary original feed is not performed.
*: Optional.
1-5-4
Service Manual
Y102911-6
Section DP
Jam code 71
Description An original jam in the original conveying section 1* An original size error jam*
Conditions During the secondary original feed in the single-sided or double-sided original mode, the DP timing switch (DPTSW)* does not turn off within 6500 ms of the original conveying motor (OCM)* turning on. During the secondary original feed in the single-sided or double-sided original mode, the DP timing switch (DPTSW)* does turn off within 750 ms of the original conveying motor (OCM)* turning on. During scanning of the second side or reversing of the original for ejection in the double-sided original mode, the DP timing switch (DPTSW)* does not turn off within 6500 ms of the original conveying motor (OCM)* turning on. During scanning of the second side or reversing of the original for ejection in the double-sided original mode, the DP timing switch (DPTSW)* does not turn on within 750 ms of the original conveying motor (OCM)* turning on. During the switchback operation of an original in the doublesided original mode, the original switchback switch (OSBSW) *does not turn on within 1300 ms of the original conveying motor (OCM)* turning on.
72
73
An original jam in the original conveying section 2* An original jam in the original conveying section 3* An original jam in the original switchback section*
74
75
*: Optional.
Y102911-6
Service Manual
1-5-5
(3) Paper misfeeds Copier Problem (1) A paper jam in the paper feed, paper conveying or exit section is indicated as soon as the power switch is turned on. Jam code 00 Causes/check procedures A piece of paper torn from copy paper is caught around registration switch, exit sensor or feedshift switch. Defective registration switch. Defective exit switch. Corrective measures Check visually and remove it, if any.
Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding switch is not light. Run maintenance item U031 and turn exit switch on and off manually. Replace exit switch if indication of the corresponding switch is not light. Run maintenance item U031 and turn feedshift switch on and off manually. Replace feedshift switch if indication of the corresponding switch is not light. Change the paper. Check visually and replace any deformed pulley. Check visually and replace registration switch if its actuator is broken. Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding switch is not light.
(2) A paper jam in the paper feed section is indicated during copying (no paper feed from the bypass tray). Jam code 10
Paper on the bypass tray is extremely curled. Check if the bypass paper feed pulley is deformed. Broken registration switch actuator. Defective registration switch.
Check if the bypass paper feed solenoid malfunctions. Electrical problem with the bypass paper feed solenoid.
(3) A paper jam in the paper feed section is indicated during copying (no paper feed from the drawer 1). Jam code 11 Paper in the drawer is extremely curled. Check if the paper feed pulley, separation pulley or forward pulley is deformed. Broken registration switch actuator. Defective registration switch. Check if the paper feed clutch malfunctions. Electrical problem with the paper feed clutch.
Run maintenance item U032 and select the bypass paper feed solenoid to be turned on and off. Check the status and remedy if necessary.
Check (see page 1-5-29).
Check visually and replace registration switch if its actuator is broken. Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding switch is not light. Run maintenance item U032 and select the paper feed clutch to be turned on and off. Check the status and remedy if necessary. Check (see page 1-5-29).
1-5-6
Service Manual
Y102911-6
Problem (4) A paper jam in the paper feed section is indicated during copying (no paper feed from the drawer 2). Jam code 12
Causes/check procedures Paper in the first paper feeder is extremely curled. Check if the paper feed pulley, separation pulley or forward pulley in the first paper feeder is deformed. Broken registration switch actuator. Defective registration switch. Check if the drawer paper feed clutch 1 malfunctions. Electrical problem with the drawer paper feed clutch 1. Change the paper.
Corrective measures
Check visually and replace registration switch if its actuator is broken. Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding switch is not light. Run maintenance item U032 and select the drawer paper feed clutch 1 to be turned on and off. Check the status and remedy if necessary. Check.
(5) A paper jam in the paper feed section is indicated during copying (no paper feed from the drawer 3). Jam code 13
Paper in the second paper feeder is extremely curled. Check if the paper feed pulley, separation pulley or forward pulley in the second paper feeder is deformed. Broken drawer feed switch 1 actuator. Defective drawer feed switch 1. Check if the drawer paper feed clutch 2 malfunctions. Electrical problem with the drawer paper feed clutch 2.
Change the paper. Check visually and replace any deformed pulley.
Check visually and replace drawer feed switch 1 if its actuator is broken. Run maintenance item U031 and turn drawer feed switch 1 on and off manually. Replace drawer feed switch 1 if indication of the corresponding switch is not light. Run maintenance item U032 and select the drawer paper feed clutch 2 to be turned on and off. Check the status and remedy if necessary. Check.
(6) A paper jam in the paper feed section is indicated during copying (no paper feed from the drawer 4). Jam code 14
Paper in the third paper feeder is extremely curled. Check if the paper feed pulley, separation pulley or forward pulley in the third paper feeder is deformed. Broken drawer feed switch 2 actuator. Defective drawer feed switch 2.
Change the paper. Check visually and replace any deformed pulley.
Check visually and replace drawer feed switch 2 if its actuator is broken. Run maintenance item U031 and turn drawer feed switch 2 on and off manually. Replace drawer feed switch 2 if indication of the corresponding switch is not light.
Y102911-6
Service Manual
1-5-7
Problem (6) A paper jam in the paper feed section is indicated during copying (no paper feed from the drawer 4). Jam code 14 (7) A paper jam in the paper feed section is indicated during copying (misfeed in vertical paper conveying 1). Jam code 15
Causes/check procedures Check if the drawer paper feed clutch 3 malfunctions. Electrical problem with the drawer paper feed clutch 3.
Corrective measures Run maintenance item U032 and select the drawer paper feed clutch 3 to be turned on and off. Check the status and remedy if necessary. Check.
Broken registration switch actuator. Defective registration switch. Broken drawer feed switch 1 actuator. Defective drawer feed switch 1. Broken drawer feed switch 2 actuator. Defective drawer feed switch 2. Check if the paper feed clutch malfunctions. Electrical problem with the paper feed clutch. Check if the drawer paper feed clutch 1 malfunctions. Electrical problem with the drawer paper feed clutch 1. Check if the drawer paper feed clutch 2 malfunctions. Electrical problem with the drawer paper feed clutch 2. Check if the drawer paper feed clutch 3 malfunctions. Electrical problem with the drawer paper feed clutch 3.
Check visually and replace registration switch if its actuator is broken. Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding switch is not light. Check visually and replace drawer feed switch 1 if its actuator is broken. Run maintenance item U031 and turn drawer feed switch 1 on and off manually. Replace drawer feed switch 1 if indication of the corresponding switch is not light. Check visually and replace drawer feed switch 2 if its actuator is broken. Run maintenance item U031 and turn drawer feed switch 2 on and off manually. Replace drawer feed switch 2 if indication of the corresponding switch is not light. Run maintenance item U032 and select the paper feed clutch to be turned on and off. Check the status and remedy if necessary. Check (see page 1-5-29). Run maintenance item U032 and select the drawer paper feed clutch 1 to be turned on and off. Check the status and remedy if necessary. Check.
Run maintenance item U032 and select the drawer paper feed clutch 2 to be turned on and off. Check the status and remedy if necessary. Check.
Run maintenance item U032 and select the drawer paper feed clutch 3 to be turned on and off. Check the status and remedy if necessary. Check.
1-5-8
Service Manual
Y102911-6
Problem (8) A paper jam in the paper feed section is indicated during copying (misfeed in vertical paper conveying 2). Jam code 16
Causes/check procedures Broken drawer feed switch 1 actuator. Defective drawer feed switch 1. Broken drawer feed switch 2 actuator. Defective drawer feed switch 2. Check if the drawer paper feed clutch 1 malfunctions. Electrical problem with the drawer paper feed clutch 1. Check if the drawer paper feed clutch 2 malfunctions. Electrical problem with the drawer paper feed clutch 2.
Corrective measures Check visually and replace drawer feed switch 1 if its actuator is broken. Run maintenance item U031 and turn drawer feed switch 1 on and off manually. Replace drawer feed switch 1 if indication of the corresponding switch is not light. Check visually and replace drawer feed switch 2 if its actuator is broken. Run maintenance item U031 and turn drawer feed switch 2 on and off manually. Replace drawer feed switch 2 if indication of the corresponding switch is not light. Run maintenance item U032 and select the drawer paper feed clutch 1 to be turned on and off. Check the status and remedy if necessary. Check.
Run maintenance item U032 and select the drawer paper feed clutch 2 to be turned on and off. Check the status and remedy if necessary. Check.
(9) A paper jam in the paper conveying section is indicated during copying (multiple sheets in the bypass tray). Jam code 20
Deformed guides along the paper conveying path. Broken registration switch actuator. Defective registration switch. Check if the bypass paper feed clutch malfunctions.
Repair or replace if necessary. Check visually and replace registration switch if its actuator is broken. Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding switch is not light. Run maintenance item U032 and select the bypass paper feed clutch to be turned on and off. Check the status and remedy if necessary. Check (see page 1-5-29). Check visually and remedy if necessary.
Repair or replace if necessary. Check visually and replace registration switch if its actuator is broken. Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding switch is not light. Run maintenance item U032 and select the paper feed clutch to be turned on and off. Check the status and remedy if necessary.
Y102911-6
Service Manual
1-5-9
Problem (10) A paper jam in the paper conveying section is indicated during copying (multiple sheets in the drawer 1). Jam code 21 (11) A paper jam in the paper conveying section is indicated during copying (multiple sheets in the drawer 2). Jam code 22
Causes/check procedures Electrical problem with the paper feed clutch. Check if the right and left registration rollers contact each other.
Corrective measures Check (see page 1-5-29). Check visually and remedy if necessary.
Deformed guides along the paper conveying path. Broken registration switch actuator. Defective registration switch. Check if the drawer paper feed clutch 1 malfunctions. Electrical problem with the drawer paper feed clutch 1. Check if the right and left registration rollers contact each other.
Repair or replace if necessary. Check visually and replace registration switch if its actuator is broken. Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding switch is not light. Run maintenance item U032 and select the drawer paper feed clutch 1 to be turned on and off. Check the status and remedy if necessary. Check.
(12) A paper jam in the paper conveying section is indicated during copying (multiple sheets in the drawer 3). Jam code 23
Deformed guides along the paper conveying path. Broken drawer feed switch 1 actuator. Defective drawer feed switch 1. Check if the drawer paper feed clutch 2 malfunctions. Electrical problem with the drawer paper feed clutch 2.
Repair or replace if necessary. Check visually and replace drawer feed switch 1 if its actuator is broken. Run maintenance item U031 and turn drawer feed switch 1 on and off manually. Replace drawer feed switch 1 if indication of the corresponding switch is not light. Run maintenance item U032 and select the drawer paper feed clutch 2 to be turned on and off. Check the status and remedy if necessary. Check.
(13) A paper jam in the paper conveying section is indicated during copying (multiple sheets in the drawer 4). Jam code 24
Deformed guides along the paper conveying path. Broken drawer feed switch 2 actuator. Defective drawer feed switch 2. Check if the drawer paper feed clutch 3 malfunctions.
Repair or replace if necessary. Check visually and replace drawer feed switch 2 if its actuator is broken. Run maintenance item U031 and turn drawer feed switch 2 on and off manually. Replace drawer feed switch 2 if indication of the corresponding switch is not light. Run maintenance item U032 and select the drawer paper feed clutch 3 to be turned on and off. Check the status and remedy if necessary.
1-5-10
Service Manual
Y102911-6
Problem (13) A paper jam in the paper conveying section is indicated during copying (multiple sheets in the drawer 4). Jam code 24 (14) A paper jam in the fixing section is indicated during copying (misfeed in the fixing section). Jam code 40
Causes/check procedures Electrical problem with the drawer paper feed clutch 3. Check.
Corrective measures
Check if the fixing unit front guide is deformed. Check if the press roller is extremely dirty or deformed. Check if the heat roller separation claws are dirty or deformed. Check if the heat roller and its separation claws contact each other. Broken exit switch actuator. Defective exit switch.
Check visually and replace the exit switch if its actuator is broken. Run maintenance item U031 and turn exit switch on and off manually. Replace exit switch if indication of the corresponding switch is not light. Run maintenance item U030 and select the registration motor to be turned on and off. Check the status and remedy if necessary. Check (see page 1-5-28). Check visually and replace registration switch if its actuator is broken. Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding switch is not light. Check visually and replace the exit switch if its actuator is broken. Run maintenance item U031 and turn exit switch on and off manually. Replace exit switch if indication of the corresponding switch is not light. Run maintenance item U030 and select the registration motor to be turned on and off. Check the status and remedy if necessary. Check (see page 1-5-28).
Check if the registration motor malfunctions. Electrical problem with the registration motor. (15) A paper jam in the exit section is indicated during copying (misfeed in the exit section). Jam code 50 Broken registration switch actuator. Defective registration switch. Broken exit switch actuator. Defective exit switch.
Check if the registration motor malfunctions. Electrical problem with the registration motor.
Y102911-6
Service Manual
1-5-11
Problem (16) A paper jam in the feedshift section is indicated during copying (misfeed in the feedshift section). Jam code 52
Corrective measures Check visually and replace the feedshift switch if its actuator is broken. Run maintenance item U031 and turn feedshift switch on and off manually. Replace feedshift switch if indication of the corresponding switch is not light. Run maintenance item U030 and select the exit motor to be turned on and off. Check the status and remedy if necessary. Check (see page 1-5-28). Check visually and replace the feedshift switch if its actuator is broken. Run maintenance item U031 and turn feedshift switch on and off manually. Replace feedshift switch if indication of the corresponding switch is not light. Check visually and replace the duplex paper conveying switch if its actuator is broken. Run maintenance item U031 and turn duplex paper conveying switch on and off manually. Replace duplex paper conveying switch if indication of the corresponding switch is not light. Run maintenance item U030 and select the exit motor to be turned on and off. Check the status and remedy if necessary. Check (see page 1-5-28). Check visually and remedy if necessary. Check. Check visually and replace the duplex paper conveying switch if its actuator is broken. Run maintenance item U031 and turn duplex paper conveying switch on and off manually. Replace duplex paper conveying switch if indication of the corresponding switch is not light. Check visually and replace the registration switch if its actuator is broken. Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding switch is not light. Check visually and remedy if necessary. Check.
Check if the exit motor malfunctions. Electrical problem with the exit motor.
(17) A paper jam in the duplex section is indicated during copying (misfeed in duplex paper conveying section). Jam code 60
Broken duplex paper conveying switch actuator. Defective duplex paper conveying switch. Check if the exit motor malfunctions. Electrical problem with the exit motor. Check if the duplex feed clutch malfunctions. Electrical problem with the duplex feed clutch.
(18) A paper jam in the duplex section is indicated during copying (misfeed in duplex exit section). Jam code 61
Broken duplex paper conveying switch actuator. Defective duplex paper conveying switch. Broken registration switch actuator. Defective registration switch. Check if the duplex feed clutch malfunctions. Electrical problem with the duplex feed clutch.
1-5-12
Service Manual
Y102911-6
DP Problem (1) An original jams when the power switch is turned on. Causes/check procedures A piece of paper torn from an original is caught around the DP timing switch or original switchback switch. Defective DP timing switch. Defective original switchback switch. (2) An original jams in the original feed section is indicated during copying (no original feed). Jam code 70 Defective original set switch. Check if the original feed motor malfunctions. Check if the DP paper feed pulley or DP separation pad is deformed. (3) An original jams in the original conveying section is indicated during copying (An original jam in the original conveying section 1). Jam code 71 (4) An original jams in the original conveying section is indicated during copying (An original size error jam). Jam code 72 (5) An original jams in the original conveying section is indicated during copying (An original jam in the original conveying section 2). Jam code 73 Broken DP timing switch actuator. Defective DP timing switch. Check if the original conveying motor malfunctions. Broken DP timing switch actuator. Defective DP timing switch. Check if the original conveying motor malfunctions. Broken DP timing switch actuator. Defective DP timing switch. Check if the original conveying motor malfunctions. Check if the switchback feedshift solenoid malfunctions. Corrective measures Check visually and remove it, if any.
Run maintenance item U244 and turn DP timing switch on and off manually. Replace DP timing switch if indication of the corresponding switch is not light. Run maintenance item U244 and turn original switchback switch on and off manually. Replace original switchback switch if indication of the corresponding switch is not light. Run maintenance item U244 and turn original set switch on and off manually. Replace original set switch if indication of the corresponding switch is not light. Run maintenance item U243 and select the original feed motor to be turned on and off. Check the status and remedy if necessary. Check visually and replace the deformed pulley.
Check visually and replace DP timing switch if its actuator is broken. Run maintenance item U244 and turn DP timing switch on and off manually. Replace DP timing switch if indication of the corresponding switch is not light. Run maintenance item U243 and select the original conveying motor to be turned on and off. Check the status and remedy if necessary. Check visually and replace DP timing switch if its actuator is broken. Run maintenance item U244 and turn DP timing switch on and off manually. Replace DP timing switch if indication of the corresponding switch is not light. Run maintenance item U243 and select the original conveying motor to be turned on and off. Check the status and remedy if necessary. Check visually and replace DP timing switch if its actuator is broken. Run maintenance item U244 and turn DP timing switch on and off manually. Replace DP timing switch if indication of the corresponding switch is not light. Run maintenance item U243 and select the original conveying motor to be turned on and off. Check the status and remedy if necessary. Run maintenance item U243 and select the switchback feedshift solenoid to be turned on and off. Check the status and remedy if necessary.
Y102911-6
Service Manual
1-5-13
Problem (6) An original jams in the original conveying section is indicated during copying (An original jam in the original conveying section 3). Jam code 74
Causes/check procedures Broken DP timing switch actuator. Defective DP timing switch. Check if the original conveying motor malfunctions. Check if the switchback feedshift solenoid malfunctions.
Corrective measures Check visually and replace DP timing switch if its actuator is broken. Run maintenance item U244 and turn DP timing switch on and off manually. Replace DP timing switch if indication of the corresponding switch is not light. Run maintenance item U243 and select the original conveying motor to be turned on and off. Check the status and remedy if necessary. Run maintenance item U243 and select the switchback feedshift solenoid to be turned on and off. Check the status and remedy if necessary. Run maintenance item U244 and turn original switchback switch on and off manually. Replace original switchback switch if indication of the corresponding switch is not light. Run maintenance item U243 and select the original conveying motor to be turned on and off. Check the status and remedy if necessary. Run maintenance item U243 and select the switchback feedshift solenoid to be turned on and off. Check the status and remedy if necessary. Use only originals conforming to the specifications. Clean with isopropyl alcohol.
(7) An original jams in the original switchback section is indicated during copying (An original jam in the original switchback section). Jam code 75 (8) Original jams frequently.
Defective original switchback switch. Check if the original conveying motor malfunctions. Check if the switchback feedshift solenoid malfunctions. An original outside the specifications is used. The DP forwarding pulley or DP paper feed pulley is dirty with paper powder. The DP paper feed pulley and DP separation pad do not contact correctly.
1-5-14
Service Manual
Y102911-6
1-5-2 Self-diagnosis
(1) Self-diagnostic function This unit is equipped with a self-diagnostic function. When a problem is detected, copying is disabled. "C" and a number between 0100 and 7810 altenates, indicating the nature of the problem. After removing the problem, the self-diagnostic function can be reset by opening and closing the front cover to turn safety switch off and on or power switch turns off and on. (2) Self diagnostic codes Code Contents Remarks Causes Defective backup RAM or main PCB. Problem with the backup memory data. Defective backup RAM. Defective backup RAM or engine PCB. Problem with the backup memory data. Defective backup RAM. Defective main PCB or engine PCB. Check procedures/corrective measures Replace the main PCB and check for correct operation. Turn safety switch off and back on and run maintenance item U020 to set the contents of the backup memory data again. If the C011 is displayed after re-setting the backup memory contents, replace the backup RAM or main PCB. Replace the engine PCB and check for correct operation. Turn safety switch off and back on and run maintenance item U020 to set the contents of the backup memory data again. If the C016 is displayed after re-setting the backup memory contents, replace the backup RAM or engine PCB. Replace the main PCB or engine PCB and check for correct operation.
Backup memory read/write problem C0100 (A0100*) (main PCB) Read and write data does not match. Backup memory data problem (main C0110 (A0110*) PCB) Data in the specified area of the backup memory does not match the specified values.
Backup memory read/write problem C0150 (A0150*) (engine PCB) Read and write data does not match. C016 (A016*) Backup memory data problem (engine PCB) Data in the specified area of the backup memory does not match the specified values.
C0170
Accounting count problem When the power is turned on, the total count and the scan count are abnormal both on the main PCB and the engine PCB. Machine number mismatch When the power is turned on, the machine number does not match between the main PCB and the engine PCB.
C0180
Correct EEPROM is not installed. Data damage of EEPROM. Poor contact in the connector terminals.
Install the correct EEPROM. If it does not solve the problem, contact the Service Administrative Division. Contact the Service Administrative Division. Check the connection of connectors YC6 on the main PCB and YC1 on the engine PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB or engine PCB and check for correct operation. Check the installation state of the DP and adjust it if it is not properly installed. Replace the main PCB or DP driver PCB and check for correct operation.
Communication problem between C0210 (A0210*) the main PCB and engine board PCB When the power is turned on, the machine does not detect the low level of SBSY and the high level of SDIR for three seconds.
Defective main PCB or engine PCB. DP installed incorrectly. Defective main PCB or DP driver PCB.
Optional DP communication problem C0410 (A0410*) Communication fails five times successively.
Y102911-6
Service Manual
1-5-15
Code
Contents
Remarks Causes Paper feeder installed incorrectly. Defective main PCB or drawer main PCB. Paper feeder installed incorrectly. Defective main PCB or drawer main PCB. Paper feeder installed incorrectly. Defective main PCB or drawer main PCB. Defective main PCB. DIMM installed incorrectly. Defective DIMM. Check procedures/corrective measures Check the installation state of the paper feeder and adjust it if it is not properly installed. Replace the main PCB or drawer main PCB and check for correct operation. Check the installation state of the paper feeder and adjust it if it is not properly installed. Replace the main PCB or drawer main PCB and check for correct operation. Check the installation state of the paper feeder and adjust it if it is not properly installed. Replace the main PCB or drawer main PCB and check for correct operation. Replace the main PCB and check for correct operation. Check if the DIMM is inserted into the socket on the main PCB correctly. Replace the DIMM and check for correct operation. Replace the main PCB and check for correct operation.
Optional first paper feeder communiC0420 (A0420*) cation problem Communication fails five times successively.
Optional second paper feeder comC0500 (A0500*) munication problem Communication fails five times successively.
Optional third paper feeder commuC0510 (A0510*) nication problem Communication fails five times successively.
Bitmap (DIMM) problem C0610 (A0610*) There is a problem with the data or address bus of the bitmap DRAM.
Memory input interface problem C0620 (A0620*) Reading-in of an image does not complete within 10 s of the start of image transmission. DMA problem C0630 (A0630*) DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time. Image processing problem C0800 (A0800*) JAM05 is detected twice. C2000 Drive motor problem LOCK ALM signal remains high for 1 s, 1 s after the drive motor has turned on.
Defective engine PCB. Poor contact in the main motor connector terminals. Defective drive motor rotation control circuit. Defective drive transmission system.
Replace the engine PCB and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the drive motor.
Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.
1-5-16
Service Manual
Y102911-6
Code C3100
Contents Scanner carriage problem The home position is not correct when the power is turned on or copying the document placed on the contact glass.
Remarks Causes Poor contact of the connector terminals. Defective scanner home position switch. Defective engine PCB. Defective scanner motor. Check procedures/corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the scanner home position switch.
Replace the engine PCB and check for correct operation. Replace the scanner motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the exposure lamp or inverter board. Replace the engine PCB and check for correct operation. Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the scanner home position switch. Replace the exposure lamp or inverter board. Replace the engine PCB and check for correct operation. Adjust the position of the contact glass (shading plate). If the problem still occurs, replace the scanner home position switch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the LSU. Replace the engine PCB and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the LSU. Replace the engine PCB and check for correct operation.
Exposure lamp problem C3200 (A3200*) In indicator check before starting copying, the average value in scanning of the shading plate with the CCD is 128 or more.
Poor contact of the connector terminals. Defective exposure lamp or inverter board. Defective engine PCB. Incorrect shading position.
Optical system (AGC) problem C3300 (A3300*) After AGC, correct input is not obtained at CCD.
Insufficient exposure lamp luminosity. Defective engine PCB. Incorrect shading position.
C4000
Polygon motor synchronization problem The polygon motor does not reach the stable speed within 15 s of the START signal turning on.
Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PCB.
C4010
Polygon motor steady-state problem The polygon motor rotation is not stable for 5 s after the polygon motor rotation has been stabilized.
Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective engine PCB.
Y102911-6
Service Manual
1-5-17
Code
Contents
Remarks Causes Defective laser diode. Defective polygon motor. Defective main PCB. Defective engine PCB. Check procedures/corrective measures Replace the LSU. Replace the LSU. Replace the main PCB and check for correct operation. Replace the engine PCB and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check and reinstall if necessary.
BD steady-state problem C4200 (A4200*) The MIC detects a BD error for 600 ms after the polygon motor rotation has been stabilized.
C6000
Broken fixing heater wire In fixing warm-up, the time to reach 50C/122 F exceeds 13.5 s, the time to reach 100C/212 F exceeds 10 s, the time to reach the primary stabilization exceeds 10 s or the time to reach the secondary stabilization exceeds 24 s.
Poor contact in the thermistor connector terminals. Fixing thermistor installed incorrectly. Fixing thermostat triggered. Fixing heater M or S installed incorrectly. Broken fixing heater M or S wire.
Check for continuity. If none, replace the fixing thermostat. Check and reinstall if necessary.
Check for continuity. If none, replace the heater lamp. Measure the resistance. If it is 0 , replace the thermistor. Replace the power supply PCB and check for correct operation.
C6020
Abnormally high fixing unit thermistor temperature The fixing temperature exceeds 230C/446 F for 40 ms.
Shorted thermistor. Broken heater control circuit on the power supply PCB. Poor contact in the thermistor connector terminals. Broken fixing thermistor wire. Fixing thermistor installed incorrectly. Fixing thermostat triggered. Fixing heater M or S installed incorrectly. Broken fixing heater M or S wire.
C6050
Abnormally low fixing unit thermistor temperature The fixing temperature remains below 90C/194F for 1 s.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Measure the resistance. If it is , replace the fixing thermistor. Check and reinstall if necessary.
Check for continuity. If none, replace the fixing thermostat. Check and reinstall if necessary.
1-5-18
Service Manual
Y102911-6
Code C6400
Contents Zero-crossing signal problem The engine PCB does not detect the zero-crossing signal for the time specified below. At power-on: 3 s Others: 5 s
Remarks Causes Poor contact in the connector terminals. Defective power supply PCB. Defective engine PCB. Check procedures/corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if the zero-crossing signal is output from CN2-5 on the power supply PCB. If not, replace the power supply PCB. Replace the engine PCB if C640 is detected while CN2-5 on the power supply PCB outputs the zero-crossing signal. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the drawer PCB and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the drawer PCB and check for correct operation.
C7800
Poor contact in the humidity sensor connector terminals. Defective humidity sensor.
C7810
Poor contact in the humidity sensor connector terminals. Defective humidity sensor.
Y102911-6
Service Manual
1-5-19
See page 1-5-22 (8) One side of the copy image is darker than the other.
See page 1-5-23 (11) The leading edge of the image is consistently misaligned with the original.
See page 1-5-23 (12) The leading edge of the image is sporadically misaligned with the original.
See page 1-5-25 (18) Image center does not align with the original center.
1-5-20
Service Manual
Y102911-6
Causes 1. No transfer charging. A. The connector terminals of the high-voltage PCB make poor contact. B. Defective engine PCB. C. Defective high-voltage PCB. 2. No LSU laser is output. A. Defective laser scanner unit. B. Defective main PCB. 3. No developing bias is output. A. The connector terminals of the high-voltage PCB make poor contact. B. Defective engine PCB. C. Defective high-voltage PCB.
Check procedures/corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the engine PCB and check for correct operation. Replace the high voltage PCB and check for correct operation. Replace the laser scanner unit (see page 1-6-24). Replace the main PCB and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the engine PCB and check for correct operation. Replace the high voltage PCB and check for correct operation.
Causes
1. No main charging. A. Broken main charger wire. B. Leaking main charger housing. C. The connector terminals of the high-voltage PCB make poor contact. D. Defective engine PCB. E. Defective high-voltage PCB. Replace the main charger unit (see page 1-6-35). Clean the main charger wire, grid and shield. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if YC9-5 on the engine PCB goes low when maintenance item U100 is run. If not, replace the engine PCB. Check if main charging takes place when YC1-12 on the highvoltage PCB goes low while maintenance item U100 is run. If not, replace the high-voltage PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if the exposure lamp lights when YC1-1 and 1-6 on the inverter PCB go low while maintenance item U061 is run. If not, replace the inverter PCB. Check if YC17-1 and YC17-6 on the engine PCB goes low when maintenance item U061 is run. If not, replace the engine PCB.
2. Exposure lamp fails to light. A. The connector terminals of the exposure lamp make poor contact. B. Defective inverter PCB.
Y102911-6
Service Manual
1-5-21
Causes 1. Insufficient toner. 2. The transfer voltage is not output properly. 3. Dirty main charger wire. 4. Dirty main charger grid.
Causes
1. Insufficient toner. 2. The transfer voltage is not output properly. 3. Dirty main charger wire. 4. Dirty main charger grid.
If the add toner indicator lights, replace the toner container. Clean or check the transfer roller (see page 1-6-37). Clean the main charger wire or, if it is extremely dirty, replace the main chager unit (see page 1-6-35). Clean the main charger grid or, if it is extremely dirty, replace the main chager unit (see page 1-6-35).
Causes 1. The developing bias voltage is not properly. 2. Dirty main charger wire.
Causes
1. The developing bias voltage is not properly. 2. Dirty main charger wire.
Replace the high voltage PCB and check for correct operation. Clean the main charger wire or, if it is extremely dirty, replace the main chager unit (see page 1-6-35).
Causes 1. Dirty main charger wire. 2. Foreign matter in the developing unit. 3. Dirty shading plate.
Causes
1. Dirty main charger wire. 2. Foreign matter in the developing unit. 3. Dirty shading plate.
Clean the main charger wire or, if it is extremely dirty, replace the main chager unit (see page 1-6-35). Check if the magnetic brush is formed uniformly. Replace the developing unit if any foreign matter (see page 1-6-36). Clean the shading plate.
1-5-22
Service Manual
Y102911-6
Causes 1. Dirty contact glass. 2. Dirty or flawed drum. 3. Dirty scanner mirror. 4. Dirty main charger wire.
Causes
1. Dirty contact glass. 2. Dirty or flawed drum. 3. Dirty scanner mirror. 4. Dirty main charger wire.
Clean the contact glass. Clean the drum or, if it is flawed, replace the drum unit (see page 1-6-33). Clean the scanner mirror. Clean the main charger wire or, if it is extremely dirty, replace the main chager unit (see page 1-6-35).
Causes 1. Dirty contact glass. 2. Dirty or flawed drum. 3. Dirty scanner mirror. 4. Dirty shading plate. 5. Leaking main charger housing.
Causes
1. Dirty contact glass. 2. Dirty or flawed drum. 3. Dirty scanner mirror. 4. Dirty shading plate. 5. Leaking main charger housing.
Clean the contact glass. Clean the drum or, if it is flawed, replace it (see page 1-6-33). Clean the scanner mirror. Clean the shading plate. Clean the main charger wire, grid and shield.
(8) One side of the copy image is darker than the other.
Causes
Clean the main charger wire or, if it is extremely dirty, replace the main chager unit (see page 1-6-35). Check if the exposure lamp light is distributed evenly. If not, replace the exposure lamp and inverter PCB.
Y102911-6
Service Manual
1-5-23
Causes 1. Dirty or flawed drum. 2. Dirty contact glass. 3. Deformed or worn cleaning blade. 4. Dirty drum separation claws. 5. Dirty heat roller separation claws.
Causes
1. Dirty or flawed drum. 2. Dirty contact glass. 3. Deformed or worn cleaning blade. 4. Dirty drum separation claws. 5. Dirty the heat roller separation claws.
Clean the drum or, if it is flawed, replace the drum unit (see page 1-6-33). Clean the contact glass. Replace the drum unit (see page 1-6-33). Clean the drum separation claws. Clean the heat roller separation claws.
Causes 1. Scanner moves erratically. 2. Deformed press roller. 3. Paper conveying section drive problem.
Causes
1. Scanner moves erratically. 2. Deformed press roller. 3. Paper conveying section drive problem.
Check if there is any foreign matter on the front and rear scanner rails. If any, remove it. Replace the press roller (see page 1-6-39). Check the gears and belts and, if necessary, grease them.
(11) The leading edge of the image is consistently misaligned with the original.
Causes 1. Misadjusted leading edge registration. 2. Misadjusted scanner leading edge registration.
Causes
Readjust the leading edge registration (see pages 1-6-12). Readjust the scanner leading edge registration (see page 1-6-30).
1-5-24
Service Manual
Y102911-6
(12) The leading edge of the image is sporadically misaligned with the original.
Causes 1. Paper feed clutch, bypass paper feed clutch or registration motor installed or operating incorrectly.
Causes
1. Paper feed clutch, bypass paper feed clutch or registration motor installed or operating incorrectly.
Check the installation position and operation of the paper feed clutch, bypass paper feed clutch and registration motor. If any of them operates incorrectly, replace it.
Causes 1. Paper curled. 2. Paper damp. 3. Defective pressure springs. 4. Defective separation. 5. Dirty separation electrode.
Causes
1. Paper curled. 2. Paper damp. 3. Defective pressure springs. 4. Defective separation. 5. Dirty separation electrode.
Check the paper storage conditions. Check the paper storage conditions. Replace the pressure springs. Check the drum separation claws and heat roller separation claws. Clean the separation electrode.
Causes
Replace the drum unit (see page 1-6-33). Check the heat roller and press roller.
Y102911-6
Service Manual
1-5-25
Causes 1. Paper damp. 2. Paper creased. 3. Dirty or flawed drum. 4. Dirty transfer roller.
Causes
1. Paper damp. 2. Paper creased. 3. Dirty or flawed drum. 4. Dirty transfer roller.
Check the paper storage conditions. Replace the paper. Clean the drum or, if it is flawed, replace the drum unit (see page 1-6-33). Clean the transfer roller.
Causes 1. Wrong paper. 2. Defective pressure springs. 3. Flawed press roller. 4. Defective fixing heater.
Causes
1. Wrong paper. 2. Defective pressure springs. 3. Flawed press roller. 4. Defective fixing heater.
Check if the paper meets specifications. Replace the pressure springs. Replace the press roller (see page 1-6-39). Replace the fixing heater (see page 1-6-40).
Causes
Replace the image scanning unit (see page 1-6-23). Clean the drum.
1-5-26
Service Manual
Y102911-6
(18) Image center does not Causes align with the original 1. Misadjusted center line of image printing. center. 2. Misadjusted scanner center line. 3. Original placed incorrectly.
Causes
1. Misadjusted center line of image printing. 2. Misadjusted scanner center line. 3. Original placed incorrectly.
Readjust the center line of image printing (see page 1-6-14). Readjust the scanner center line (see page 1-6-31). Place the original correctly.
Y102911-6
Service Manual
1-5-27
Check for continuity. If none, replace the cord. Check for continuity across the contacts. If none, replace the power switch. Check for continuity. If none, remove the cause of blowing and replace the fuse. Check for continuity across the contacts of each switch. If none, replace the switch. With AC present, check for 24 V DC at YC1-1 and 5 V DC at YC1-7 on the power source PCB. If none, replace the power source PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check visually and replace the drive motor if necessary. Run maintenance item U030 and check if the drive motor operates when YC7-5 on the engine PCB goes low. If not, replace the drive motor. Run maintenance item U030 and check if YC7-5 on the engine PCB goes low. If not, replace the engine PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check visually and replace the registration motor if necessary. Run maintenance item U030 and check if the registration motor operates when YC2-1,2,4,5 on the registration motor PCB goes low. If not, replace the registration motor. Run maintenance item U030 and check if YC4-4 on the engine PCB goes low. If not, replace the engine PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check visually and replace the exit motor if necessary. Run maintenance item U030 and check if the exit motor operates when YC14-1,2,3,4 on the engine PCB go low. If not, replace the exit motor. Run maintenance item U030 and check if YC14-1,2,3,4 on the engine PCB go low. If not, replace the engine PCB.
Defective engine PCB. (3) The registration motor does not operate. Poor contact in the registration motor connector terminals. Broken registration motor gear. Defective registration motor. Defective engine PCB. (4) The exit motor does not operate. Poor contact in the exit motor connector terminals. Broken exit motor gear. Defective exit motor.
1-5-28
Service Manual
Y102911-6
Causes Broken scanner motor coil. Poor contact in the scanner motor connector terminals. Broken cooling fan motor 1 coil. Poor contact in the cooling fan motor 1 connector terminals. Broken cooling fan motor 2 coil. Poor contact in the cooling fan motor 2 connector terminals. Broken paper feed clutch coil. Poor contact in the paper feed clutch connector terminals. Defective engine PCB.
Check procedures/corrective measures Check for continuity across the coil. If none, replace the scanner motor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Check for continuity across the coil. If none, replace cooling fan motor 1. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable.
Check for continuity across the coil. If none, replace cooling fan motor 2. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable.
Check for continuity across the coil. If none, replace the paper feed clutch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if YC8-3 on the engine PCB goes low. If not, replace the engine PCB. Check for continuity across the coil. If none, replace the bypass paper feed clutch. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U032 and check if YC8-5 on the engine PCB goes low. If not, replace the engine PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity. If none, replace the cleaning lamp. If the cleaning lamp turns on when YC3-7,8 on the engine PCB is held low, replace the engine PCB. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Run maintenance item U061 and check if the exposure lamp turns on with YC1-1 and YC1-6 on the inverter PCB go low. If not, replace the inverter PCB. Run maintenance item U061 and check if YC17-1 and YC17-6 on the engine PCB goes low. If not, replace the engine PCB.
Broken bypass paper feed clutch coil. Poor contact in the bypass paper feed clutch connector terminals. Defective engine PCB.
Poor contact in the cleaning lamp connector terminals. Defective cleaning lamp. Defective engine PCB.
Poor contact in the exposure lamp connector terminals. Defective inverter PCB.
Y102911-6
Service Manual
1-5-29
Causes Defective inverter PCB. Defective engine PCB. Broken wire in fixing heater M or S. Fixing thermostat triggered. Broken fixing thermistor wire. Dirty sensor part of the fixing thermistor. Broken main charger wire. Leaking main charger housing. Poor contact in the highvoltage PCB connector terminals. Defective engine PCB. Defective high- voltage PCB.
Check procedures/corrective measures If the exposure lamp does not turn off with YC1-1 and YC1-6 on the inverter PCB high, replace the inverter PCB. If YC17-1 and YC17-6 on the engine PCB are always low, replace the engine PCB. Check for continuity across each heater. If none, replace the heater M or S. Check for continuity across thermostat. If none, remove the cause and replace the thermostat. Measure the resistance. If it is , replace the fixing thermistor. Check visually and clean the thermistor sensor parts. See page 1-5-21.
(13) The fixing heater does not turn on (C6000). (14) The fixing heater does not turn off.
Poor contact in the highvoltage PCB connector terminals. Defective engine PCB. Defective high-voltage PCB.
Poor contact in the highvoltage PCB connector terminals. Defective engine PCB. Defective high-voltage PCB.
(18) The original size is not detected. (19) The original size is not detected correctly.
Defective original detection switch. Original is not placed correctly. Poor contact in the original size detection sensor connector terminals. Defective original size detection sensor.
If the level of YC18-5 on the engine PCB does not change when the original detection switch is turned on and off, replace the original detection switch. Check the original and correct if necessary. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if sensor operates correctly. If not, replace it.
1-5-30
Service Manual
Y102911-6
Problem (20) The message requesting paper to be loaded is shown when paper is present in the drawer. (21) The size of paper in the drawer is not displayed correctly.
Causes Poor contact in the paper switch connector terminals. Defective paper switch.
Check procedures/corrective measures Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. If the level of YC8-2 on the engine PCB does not change when the paper switch is turned on and off, replace the paper switch.
Poor contact in the paper length switch connector terminals. Defective paper length switch. A piece of paper torn from copy paper is caught around registration switch, exit switch or feedshift switch. Defective registration switch. Defective exit switch.
Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check if YC22-1,2,4 on the engine PCB goes low when the paper length switch is turned on. If not, replace the paper length switch. Check and remove if any.
(22) A paper jam in the paper feed, paper conveying or fixing section is indicated when the power switch is turned on.
Run maintenance item U031 and turn registration switch on and off manually. Replace registration switch if indication of the corresponding sensor is not light. Run maintenance item U031 and turn exit switch on and off manually. Replace exit switch if indication of the corresponding sensor is not light. Run maintenance item U031 and turn feedshift switch on and off manually. Replace feedshift switch if indication of the corresponding sensor is not light. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check for continuity across each switch. If there is no continuity when the switch is on, replace it.
(23) The message requesting covers to be closed is displayed when the front cover and left cover are closed. (24) Others.
Poor contact in the connector terminals of safety switch. Defective safety switch.
Check for continuity. If none, repair. Locate the source of noise and remove.
Y102911-6
Service Manual
1-5-31
Check visually and replace any deformed pulleys (see page 1-6-3 and 5). See pages 1-5-29.
See page 1-5-28. Check the width guide visually and correct or replace if necessary. Repair or replace if necessary . Repair or replace. Reinstall the scanner wire (see page 1-618). See page 1-5-29. Replace the separation pulley if it is worn (see page 1-6-3). Change the paper. Change the paper. Repair or replace if necessary. Check visually and remedy if necessary. Clean or replace the press roller (see page 1-6-39). Repair if any springs are off the separation claws. Check visually and remedy if necessary. Clean the developing unit.
1-5-32
Service Manual
Y102911-6
Y102911-6
Service Manual
1-6-1
Start
Enter the maintenance item number using the zoom +/- keys or numeric keys.
Yes
No
Yes
No Enter 001 using the zoom +/- keys or numeric keys and press the start key.
End
1-6-2
Service Manual
Y102911-6
Drawer
Figure 1-6-1 3. Remove the screw and then the front left lower cover.
Figure 1-6-2 4. Remove the screw and then the lower paper feed unit.
Figure 1-6-3
Y102911-6
Service Manual
1-6-3
5. Remove the separation pulley unit from the lower paper feed unit. 6. Remove the separation pulley from the separation pulley unit. 7. Replace the separation pulley and refit all the removed parts.
Separation pulley
Figure 1-6-4
1-6-4
Service Manual
Y102911-6
(2) Detaching and refitting the forwarding pulley and paper feed pulley Follow the procedure below to replace the forwarding pulley and paper feed pulley. Procedure 1. Remove the lower paper feed unit (see page 1-6-3). 2. Remove the drum unit (see page 1-6-33). 3. Remove the rear cover. 4. Remove the paper feed clutch, stop ring and bushing at the machine rear.
Stop ring
Figure 1-6-5
Registration guide
Figure 1-6-6
6. Remove the screw and then the upper paper feed unit.
Figure 1-6-7
Y102911-6
Service Manual
1-6-5
7. Remove the springs, stop ring and bushing and then the shaft holder from the upper paper feed unit.
Spring
Stop ring
Bushing
Figure 1-6-8
8. Remove the forwarding pulley from the upper paper feed unit. 9. Remove the paper feed pulley from the upper paper feed unit. 10. Replace the forwarding pulley and paper feed pulley and refit all the removed parts.
Forwarding pulley
Figure 1-6-9
1-6-6
Service Manual
Y102911-6
(3) Detaching and refitting the paper conveying unit Follow the procedure below to maintenance of the paper feed section. Procedure 1. Remove the drum unit (see page 1-6-33). 2. Remove the strap from the rear side. Restore the paper conveying unit. Remove the fitting projection and pin, and then remove the stopper from the front side.
Left cover
Pin
Figure 1-6-10
3. Open the left cover until it is put horizontally. 4. Push the fitting portions of the fixtures located on the front and rear and then remove the fixtures from the left cover.
Fixture
Left cover
Fixture
Figure 1-6-11
Y102911-6
Service Manual
1-6-7
5. Remove the left cover from the copier. 6. Push the fitting portions of the bypass upper cover. Remove the bypass upper cover from
Figure 1-6-12 the bypass unit. 7. Detach the connector and remove the bypass
Connector
Figure 1-6-13
lower cover from the copier. 8. Remove the paper conveying unit from the copier.
Figure 1-6-14
1-6-8
Service Manual
Y102911-6
(4) Detaching and refitting the bypass paper feed pulley and bypass separation pad Follow the procedure below to replace the bypass paper feed pulley and bypass separation pad. Procedure 1. Open the front cover and remove the waste toner box. Pull out the drawer. 2. Remove the screw and then the front left lower cover.
Figure 1-6-15
3. Remove the paper conveying unit (see page 1-6-7). 4. Remove the stop ring and bushing at the machine front side.
Stop ring
Bushing
Figure 1-6-16
5. Remove the rear cover. 6. Remove the stop ring and bypass paper feed clutch gear at the machine rear side.
Stop ring
Figure 1-6-17
Y102911-6
Service Manual
1-6-9
7. Temporarily push the bypass paper feed pulley unit into the rear side to unlock the front side and then remove it from the copier.
Figure 1-6-18
8. Remove the bypass paper feed pulley from the bypass paper feed pulley shaft.
Bypass paper feed pulley shaft
Figure 1-6-19
9. Push the fitting portions of the bypass separation pad. Remove the bypass separation pad from the copier. 10. Replace the bypass paper feed pulley and bypass separation pad and refit all the removed parts.
Figure 1-6-20
1-6-10
Service Manual
Y102911-6
(5) Detaching and refitting the registration left roller Follow the procedure below to replace the registration left roller. Procedure 1. Remove the paper conveying unit (see page 1-6-7). 2. Remove the transfer roller (see page 1-6-37). 3. Release the stoppers at the front and rear side, and then remove the registration left roller from the paper conveying unit. 4. Replace the registration left roller and refit all the removed parts.
Stopper Paper conveying unit
Stopper
Figure 1-6-21
(6) Detaching and refitting the registration cleaner Follow the procedure below to replace the registration cleaner. Procedure 1. Remove the drum unit (see page 1-6-33). 2. Remove the screw and then the registration guide.
Trans guide film
Registration guide
Figure 1-6-22
3. Remove the screw and then the registration cleaner. 4. Replace the registration cleaner and refit all the removed parts.
Registration cleaner
Figure 1-6-23
Y102911-6
Service Manual
1-6-11
(7) Adjustment after roller and clutch replacement Perform the following adjustment after refitting rollers and clutches. (7-1) Adjusting the leading edge registration of image printing Make the following adjustment if there is a regular error between the leading edges of the copy image and original.
U066 (P. 1-6-30) U071 (P. 1-4-14)
U034
Caution: Check the copy image after the adjustment. If the image is still incorrect, perform the above adjustments in maintenance mode. Procedure
Leading edge registration
Start Correct image Enter maintenance mode. Output example 1 Output example 2
Figure 1-6-24
G Image mode selection key Photo Text
Press the image mode selection key to light the text indicator.
Select the items to be adjusted using the copy exposure adjustment keys.
G Copy exposure adjustment keys Exp. 1 (lit): Drawer Exp. 2 (lit): Bypass tray Exp. 3 (lit): First paper feeder Exp. 4 (lit): Second paper feeder Exp. 5 (lit): Third paper feeder Exp. 1 (flashing): duplex copying (second face) Press the start key The new setting is stored
Is the leading edge registration correct? Yes Press the stop/clear key to exit maintenance mode.
No
For output example 1, decrease the value using the zoom () key. For output example 2, increase the value using the zoom (+) key. Setting range (Initial setting) Drawer: 5.0 +10.0 (5.1) Bypass tray: 5.0 +10.0 (0.0) First paper feeder: 5.0 +10.0 (0.0) Second paper feeder: 5.0 +10.0 (0.0) Third paper feeder: 5.0 +10.0 (0.0) Duplex copying: 5.0 +10.0 (0.0) Changing the value by 1 moves the leading edge by 1.0 mm.
End
1-6-12
Service Manual
Y102911-6
(7-2) Adjusting the leading edge registration for memory image printing Make the following adjustment if there is a regular error between the leading edge of the copy image and the leading edge of the original during memory copying.
U053 (P. 1-4-10)
U034 (P. 1-6-12)
U407
Caution: Before making the following adjustment, ensure the above adjustments have been made in maintenance mode. Procedure
Start
Original
Enter 407 using the numeric keys.
Copy example 1
Copy example 2
Figure 1-6-25
Is the leading edge registration correct? Yes Press the stop/clear key to exit maintenance mode.
No
For copy example 1, increase the value using the zoom (+) key. For copy example 2, decrease the value using the zoom () key. Setting range: 10 +10 Initilal setting: 0 Changing the value by 1 moves the leading edge by 1 mm.
End
Y102911-6
Service Manual
1-6-13
(7-3) Adjusting the center line of image printing Make the following adjustment if there is a regular error between the center lines of the copy image and original when paper is fed from the drawer.
U067 (P. 1-6-35) U072 (P. 1-4-15)
U034
Caution: Check the copy image after the adjustment. If the image is still incorrect, perform the above adjustments in maintenance mode. Procedure
Center line of printing
Start
Correct image
Output example 1
Output example 2
Figure 1-6-26
G Image mode selection key Photo Text Photo and text indicators are on: Center line adjustment
Press the image mode selection key to light the photo and text indicators.
Select the item to be adjusted using the copy exposure adjustment keys.
G Copy exposure adjustment keys Exp. 1 (lit): Drawer Exp. 2 (lit): Bypass tray Exp. 3 (lit): First paper feeder Exp. 4 (lit): Second paper feeder Exp. 5 (lit): Third paper feeder Exp. 1 (flashing): duplex copying (second face) Press the start key. The new setting is stored.
Is the image correct? Yes Press the stop/clear key to exit maintenance mode.
No
For output example 1, decrease the value using the zoom () key. For output example 2, increase the value using the zoom (+) key. Setting range (Initial setting) Drawer: 8.0 +10.0 (1.2) Bypass tray: 8.0 +10.0 (0.0) First paper feeder: 8.0 +10.0 (0.0) Second paper feeder: 8.0 +10.0 (0.0) Third paper feeder: 8.0 +10.0 (0.0) Duplex copying: 8.0 +10.0 (0.0) Changing the value by 1 moves the center line by 1 mm.
End
1-6-14
Service Manual
Y102911-6
(7-4) Adjusting the margins for printing Make the following adjustment if the margins are not correct.
U403 (P. 1-6-32) U404 (P. 1-4-36)
U402
Caution: Check the copy image after the adjustment. If the margins are still incorrect, perform the above adjustments in maintenance mode. Procedure
Start
G Copy exposure adjustment keys Exp. 1 (lit): Printer leading edge margin Exp. 2 (lit): Printer left/right margins Exp. 3 (lit): Printer trailing edge margin
Select the item to be adjusted using the copy exposure adjustment keys.
Press the start key to output a test pattern using A3/11" 17" paper. Change the setting. Increasing the value using the zoom (+) key makes the margin wider. Decreasing the value using the zoom () key makes the margin narrower. Setting range (initial setting/change in value per step) Printer leading edge margins: 0.0 +10.0 (3.0/0.5 mm) Printer left/right margin: 5.0 +10.0 (3.0/0.5 mm) Printer trailing edge margin: 5.0 +10.0 (4.0/0.5 mm)
No
Yes Yes Proceed to another mode? No Press the stop/clear key to exit maintenance mode.
Printer leading edge margin (3 2.5 mm) Ejection direction (reference) Printer left margin +1.5 (2.52.0 mm) Printer right margin (2.5+1.5 mm) 2.0
End
Figure 1-6-27
Y102911-6
Service Manual
1-6-15
(7-5) Adjusting the amount of slack in the paper Make the following adjustment if the leading edge of the copy image is missing or varies randomly, or if the copy paper is Z-folded. Procedure
Start
Original
Enter maintenance mode.
Copy example 1
Copy example 2
Figure 1-6-28
Enter 051 using the numeric keys. G Copy exposure adjustment keys Exp. 1 (lit): Drawer Exp. 2 (lit): Bypass tray Exp. 3 (lit): First paper feeder Exp. 4 (lit): Second paper feeder Exp. 5 (lit): Third paper feeder Exp. 1 (flashing): duplex copying (second face) Press the start key. The new setting is stored. Press the start key to make a test copy.
Is the leading edge of the image missing or varying randomly (copy example 1)? No
Yes
Yes
Decrease the value using the zoom () key. Setting range (Initial setting) Drawer: 50 +50 (20) Bypass tray: 50 +50 (0) First paper feeder: 50 +127 (70) Second paper feeder: 50 +127 (80) Third paper feeder: 50 +127 (80) Duplex copying: 50 +50 (0) Changing the value by 1 changes the amount of slack by 0.32 mm. The greater the value, the larger the amount of slack; the smaller the value, the smaller the amount of slack.
End
1-6-16
Service Manual
Y102911-6
Figure 1-6-29 3. Move the mirror 1 frame to the cutouts of the machine. * When moving the mirror 1 frame, do not touch the exposure lamp nor the inverter PCB. 4. Detach the exposure lamp connector from the inverter PCB and release the wire from three clamps.
Clamps
Connector
Inverter PCB
Figure 1-6-30 5. Remove the two screws holding the exposure lamp and then the lamp. 6. Replace the exposure lamp and refit all the removed parts.
Exposure lamp
Figure 1-6-31
Y102911-6
Service Manual
1-6-17
(2) Detaching and refitting the scanner wires Take the following procedure when the scanner wires are broken or to be replaced. (2-1) Detaching the scanner wires Procedure 1. Remove the exposure lamp (see page 1-617). 2. Remove the two screws holding the upper rear cover and then the cover. Remove the two screws holding the middle left cover and upper left cover and then the covers.
Uppeer rear cover
Figure 1-6-32 3. Remove the screw and then the slit retainer and slit glass. Detach the fitting portions and then remove the front scanner cover.
Slit glass
Slit retainer
Figure 1-6-33 4. Remove the inverter wire guide and then detach the inverter wire from the inverter PCB.
Inverter wire guide
Figure 1-6-34
1-6-18
Service Manual
Y102911-6
5. Remove the screw holding each of the front and rear wire retainers and then remove the mirror 1 frame from the scanner unit.
Mirror 1 frame
Figure 1-6-35
6. Unhook the round terminal of the scanner wire from the scanner tension spring on the left side of the scanner unit. 7. Remove the scanner wire.
Figure 1-6-36
Y102911-6
Service Manual
1-6-19
(2-2) Fitting the scanner wires Caution: When fitting the wires, be sure to use those specified below. Machine front: gray Machine rear: black Fitting requires the following tools: Two frame securing tools Two scanner wire stoppers Procedure 1. Remove the screw and then scanner wire drum gear at the machine rear side.
Figure 1-6-37
2. Remove the stop ring and bushing from the front of the scanner wire drum shaft. 3. Remove the scanner wire drum shaft from the scanner unit.
Bushing
Stop ring
Figure 1-6-38
1-6-20
Service Manual
Y102911-6
4. Insert the locating ball on each of the scanner wires into the hole in the respective scanner wire drum and wind the scanner wire three turns inward and four turns outward. With the locating ball as the reference point, wind the shorter end of each of the wires outward. 5. Secure the scanner wires using the scanner wire stoppers.
Locating ball Four turns outward Scanner wire drum Four turns outward
Figure 1-6-39
6. Refit the scanner wire drum shaft to the scanner unit. 7. Insert the two frame securing tools into the positioning holes at the front and rear of the scanner unit to pin the mirror 2 frame in position.
Mirror 2 frame
Figure 1-6-40
Y102911-6
Service Manual
1-6-21
8. Loop the outer ends of the scanner wires around the outer grooves in the pulleys on the mirror 2 frame, winding from below to above. ......................................................................................................................... 1 9. Hook the round terminals onto the catches inside the scanner unit. .............................................................. 2 10. Loop the inner ends of the scanner wires around the grooves in the pulleys at the left of the scanner unit, winding from below to above. ......................................................................................................................... 3 11. Loop the scanner wires around the inner grooves in the pulleys on the mirror 2 frame, winding from above to below. .............................................................................................................................................................. 4 12. Wind the scanner wires around the grooves in the scanner wire guides at the left of the scanner unit. ........ 5 13. Hook the round terminals onto the scanner tension springs. .......................................................................... 6
Figure 1-6-41
14. Remove the scanner wire stoppers and frame securing tools. 15. Gather the scanner wires toward the locating balls. 16. Move the mirror 2 frame from side to side to correctly locate the wires in position. 17. Put the mirror 1 frame on the scanner rail and move it toward the left side of the machine. 18. Insert the frame securing tools into the positioning holes (leftmost holes) at the front and the rear of the scanner unit and screw the mirror 1 frame while securing both the mirror 1 frame and the mirror 2 frame. 19. Remove the two frame securing tools. 20. Refit all the removed parts.
Figure 1-6-42
1-6-22
Service Manual
Y102911-6
(3) Detaching and refitting the ISU (reference) Take the following procedure when the ISU is to be replaced. Procedure Detaching the ISU 1. Remove the contact glass (see page 1-6-17). 2. Remove the four screws holding the ISU cover and then the cover.
ISU cover
Figure 1-6-43 3. Detach the CCD wire from the CCD PCB. 4. Remove the four screws holding the ISU and then the ISU. 5. Replace the ISU.
CCD PCB CCD wire
ISU
Figure 1-6-44 Refitting the ISU 1. Align the positioning holes of the ISU by pushing it a little and attach the ISU to the scanner unit. * Attach the ISU with reference to marking "C". 2. Secure the ISU using the four screws. 3. Refit the CCD wire to CCD PCB. 4. Refit all the removed parts.
ISU Positioning holes
C M
Marking
Figure 1-6-45
Y102911-6
Service Manual
1-6-23
(4) Detaching and refitting the laser scanner unit Take the following procedure when the laser scanner unit is to be replaced. Procedure 1. Remove the original cover or the DP. 2. Remove the upper right cover, contact glass, upper rear cover, middle left cover, upper left cover, slit glass and front scanner cover (see page 1-6-18). 3. Remove the four screws holding the right cover and then the cover. Remove the ten screws holding the rear cover and then the cover.
Figure 1-6-46
4. Detach the connector YC8 on the main PCB. Detach the connectors YC16, YC17,YC18 and YC19 on the engine PCB.
YC8
YC16
Figure 1-6-47
1-6-24
Service Manual
Y102911-6
5. Remove the four pins holding the scanner unit and then the unit.
Pin
Pin
Pin
Figure 1-6-48 6. Remove the screw holding the exit cover and then the cover. Remove the two screws holding the inner rear cover and then the cover.
Exit cover Inner rear cover
Figure 1-6-50
Y102911-6
Service Manual
1-6-25
8. Remove the two screws holding the exit unit and then pull out the unit a little.
Exit unit
Figure 1-6-52
10. Remove the four screws and detach the two connector and then remove the laser scanner unit. 11. Replace the laser scanner unit and refit all the removed parts.
Connector
Connector
Figure 1-6-53
1-6-26
Service Manual
Y102911-6
(5) Adjusting the longitudinal squareness (reference) Perform the following adjustment if the copy image is longitudinally skewed (longitudinal squareness not obtained). Caution: Adjust the amount of slack in the paper (page 1-6-16) first. Check for the longitudinal squareness of the copy image, and if it is not obtained, perform the longitudinal squareness adjustment. Before making the following adjustment, output a VTC-PG2 pattern in maintenance item U993 to use as the original for the adjustment. Procedure
Start
Original
Place the original on the contact glass.
Copy example 1
Copy example 2
Figure 1-6-54
Press the start key and make a test copy at 100% magnification.
No
Yes
Remove the contact glass. Loosen the two screws and adjust the position of the mirror 2 frame. For copy example 1, move the frame in the direction of the white arrow (e). For copy example 2, move the frame in the direction of the black arrow (b).
End
Screws
Figure 1-6-55
Y102911-6
Service Manual
1-6-27
(6) Adjusting magnification of the scanner in the main scanning direction Perform the following adjustment if the magnification in the main scanning direction is not correct.
U053 (P. 1-4-10)
U065 (main scanning direction) U065 (auxiliary scanning direction) (P. 1-6-29)
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. Also, perform (7) Adjusting magnification of the scanner in the auxiliary scanning direction (page 1-6-29) and (9) Adjusting the scanner center line (page 1-6-31) after this adjustment. Procedure
Enter 065 using the numeric keys. Press the start key. Select exp. 1 (main scanning direction using the copy exposure adjustment keys).
Copy example
Copy example 2
Figure 1-6-56
G Copy exposure adjustment keys Exp. 1 (lit): Main scanning direction Exp. 2 (lit): Auxiliary scanning direction Press the start key. The new setting is stored.
Place an original and press the start key to make a test copy.
No
For copy example 1, increase the value using the zoom (+) key. For copy example 2, decrease the value using the zoom () key. Setting range: 25 +25 Initial setting: 0 Changing the value by 1 changes the magnification by 0.1%. Increasing the value makes the image wider, and decreasing it makes the image narrower.
End
1-6-28
Service Manual
Y102911-6
(7) Adjusting magnification of the scanner in the auxiliary scanning direction Perform the following adjustment if the magnification in the auxiliary scanning direction is not correct.
U053 (P. 1-4-10)
U065 (main scanning direction) (P. 1-6-28) U065 (auxiliary scanning direction)
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. Procedure
Enter 065 using the numeric keys. Press the start key. Select exp. 2 (auxiliary scanning direction using the copy exposure adjustment keys). Press the interrupt key. Place an original and press the start key to make a test copy.
Copy example 1
Copy example 2
Figure 1-6-57
G Copy exposure adjustment keys Exp. 1 (lit): Main scanning direction Exp. 2 (lit): Auxiliary scanning direction Press the start key. The new setting is stored.
No
For copy example 1, increase the value using the zoom (+) key. For copy example 2, decrease the value using the zoom () key. Setting range: 25 +25 Initial setting: 12 Changing the value by 1 changes the magnification by 0.1%. Increasing the value makes the image longer, and decreasing it make the image shorter.
End
Y102911-6
Service Manual
1-6-29
(8) Adjusting the scanner leading edge registration Perform the following adjustment if there is regular error between the leading edges of the copy image and original.
U034 (P. 1-6-12) U071 (P. 1-4-14)
U066
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. Procedure
Scanner leading edge registration
Start
Figure 1-6-58
Press the start key.
Place an original and press the start key to make a test copy.
Is the scanner leading edge registration correct? Yes Press the stop/clear key to exit maintenance mode.
No
For copy example 1, decrease the value using the zoom () key. For copy example 2, increase the value using the zoom (+) key. Setting range : 32 +32 Initial setting: 10 Changing the value by 1 moves the leading edge by 0.17 mm.
End
1-6-30
Service Manual
Y102911-6
(9) Adjusting the scanner center line Perform the following adjustment if there is a regular error between the center lines of the copy image and original.
U034 (P. 1-6-14) U072 (P. 1-4-15)
U067
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. Procedure
Scanner center line
Start
Enter maintenance mode. Original Enter 067 using the numeric keys. Copy example 1 Copy example 2
Figure 1-6-59
Press the start key.
Place an original and press the start key to make a test copy.
Is the scanner center line correct? Yes Press the stop/clear key to exit maintenance mode.
No
For copy example 1, increase the value using the zoom (+) key. For copy example 2, decrease the value using the zoom () key. Setting range: 66 +66 Initial setting: 0 Changing the value by 1 moves the center line by 0.17 mm.
End
Y102911-6
Service Manual
1-6-31
(10) Adjusting the margins for scanning an original on the contact glass Perform the following adjustment if the margins are not correct.
U402 (P. 1-6-15) U404 (P. 1-4-36)
U403
Caution: Before making the following adjustment, ensure that the above adjustments have been made in maintenance mode. Procedure
Start
Press the start key. G Copy exposure adjustment keys Exp. 1 (lit): Scanner left margin Exp. 2 (lit): Scanner leading edge margin Exp. 3 (lit): Scanner right margin Exp. 4 (lit): Scanner trailing edge margin Press the start key. The new setting is stored.
Select the item to be adjusted using the copy exposure adjustment keys.
Press the start key to make a test copy (A test copy is output at the reduction ratio of 95%).
Are the margins correct? Yes Yes Proceed to another mode? No Press the stop/clear key to exit maintenance mode.
No
Change the setting. Increasing the value using the zoom (+) key makes the margin wider. Decreasing the value using the zoom () key makes the margin narrower. Setting range (default) Scanner left margin: 0.0 +10.0 (2.5) Scanner leading edge margin: 0.0 +10.0 (4.0) Scanner right margin: 0.0 +10.0 (4.0) Scanner trailing edge margin: 0.0 +10.0 (3.0) Changing the value by one moves the margin by 0.5 mm for all.
Scanner leading edge margin (3 2.5 mm) Ejection direction (reference) Scanner left margin (2.5+1.5 mm) 2.0 Scanner right margin (2.5+1.5 mm) 2.0
End
Figure 1-6-60
1-6-32
Service Manual
Y102911-6
Figure 1-6-61
5. Remove the screw and detach the connector and then remove the drum unit from copier. 6. Replace the drum unit and refit all the removed parts.
Connector
Drum unit
Figure 1-6-62
Y102911-6
Service Manual
1-6-33
(2) Detaching and refitting the drum separation claws Follow the procedure below to replace the drum separation claws. Procedure 1. Remove the drum unit (see page 1-6-33). 2. Push the drum separation claws with the minus driver from the top of the corner hole and remove the claws. 3. Replace the drum separation claws and refit all the removed parts.
Drum unit
Coner hole
Figure 1-6-63
1-6-34
Service Manual
Y102911-6
(3) Detaching and refitting the main charger unit Follow the procedure below to replace the main charger unit. Procedure 1. Open the front cover. 2. While lifting the main charger unit toward the upper right, remove the unit from the copier. 3. While pressing the main charger release lever in the direction indicated by the arrow at the removal stopper position to release the removal stopper, remove the main charger unit from the copier. 4. Replace the main charger unit and refit all the removed parts.
Figure 1-6-64
Y102911-6
Service Manual
1-6-35
Developing unit
Figure 1-6-65
1-6-36
Service Manual
Y102911-6
Figure 1-6-66
3. Detach the fitting portions located on the front and rear and then remove the transfer roller from the paper conveying unit. 4. Replace the transfer roller and refit all the removed parts.
Transfer roller
Fitting portion
Fitting portion
Figure 1-6-67
Y102911-6
Service Manual
1-6-37
Figure 1-6-68a
Front left cover 2
3. Remove the screw and then remove the front left cover 2.
Screw
Figure 1-6-68b
4. Remove the screw and detach the two connectors and then remove the fixing unit from copier. 5. Replace the fixing unit and refit all the removed parts.
Connectors
Fixing unit
Figure 1-6-69
1-6-38
Service Manual
Y102911-6
(2) Detaching and refitting the press roller Follow the procedure below to replace the press roller. Procedure 1. Remove the fixing unit (see page 1-6-38). 2. Remove the two screws and then separate the fixing right unit and left unit.
Fixing right unit
Figure 1-6-70
3. Remove the three screws holding the press roller guide from fixing right unit.
Figure 1-6-71
4. Remove the press roller from the fixing right unit. 5. Replace the press roller and refit all the removed parts.
Press roller
Figure 1-6-72
Y102911-6
Service Manual
1-6-39
(3) Detaching and refitting the fixing heater M and S Follow the procedure below to replace the fixing heater M and S. Procedure 1. Remove the fixing unit and separate the fixing right unit and left unit (see page 1-6-38, 39). 2. Remove the two screws holding each of the fixing heater M and S on the front and rear of the fixing left unit.
Fixing heater S Fixing heater S
Fixing heater M
Fixing heater M
Figure 1-6-73
3. Pull out the fixing heater M and S from the fixing left unit. 4. Replace the fixing heater M and S, and refit all the removed parts.
Fixing heater M
Fixing heater S
Figure 1-6-74
1-6-40
Service Manual
Y102911-6
(4) Detaching and refitting the heat roller separation claws Follow the procedure below to replace the heat roller separation claws. Procedure 1. Remove the fixing unit and separate the fixing right unit and left unit (see page 1-6-38, 39). 2. Detach the fitting portions and then remove the heat roller guide from the fixing left unit.
Figure 1-6-75
3. Remove the heat roller separation claws from the fixing left unit. 4. Replace the heat roller separation claws and refit all the removed parts.
Figure 1-6-76
Y102911-6
Service Manual
1-6-41
(5) Detaching and refitting the heat roller Follow the procedure below to replace the heat roller. Procedure 1. Remove the fixing unit and separate the fixing right unit and left unit (see page 1-6-38, 39). 2. Remove the heat roller separation claws. (see page 1-6-41). 3. Pull out the heat roller bushing from the fixing left unit and then remove the heat roller. 4. Replace the heat roller and refit all the removed parts.
Heat roller
Figure 1-6-77
1-6-42
Service Manual
Y102911-6
(6) Detaching and refitting the fixing thermostat Follow the procedure below to replace the fixing thermostat. Procedure 1. Remove the fixing unit and separate the fixing right unit and left unit (see page 1-6-38, 39). 2. Remove the heat roller (see page 1-6-42). 3. Remove the two screws holding the fixing thermostat and then the thermostat. 4. Replace the fixing thermostat and refit all the removed parts.
Fixing thermostat
Figure 1-6-78
(7) Detaching and refitting the fixing thermistor Follow the procedure below to replace the fixing thermistor. Procedure 1. Remove the fixing unit and separate the fixing right unit and left unit (see page 1-6-38, 39). 2. Remove the heat roller (see page 1-6-42). 3. Remove the screw holding the fixing thermistor and then the thermistor. 4. Replace the fixing thermistor and refit all the removed parts.
Fixing thermistor
Figure 1-6-79
Y102911-6
Service Manual
1-6-43
Jumper switch
DIMM slot
Figure 1-7-1
Y102911-6
Service Manual
1-7-1
EEPROM
EEPROM
Figure 1-7-2
1-7-2
Service Manual
Y102911-6
1 Separation pulley 2 Forwarding pulley 3 Peper feed pulley 4 Bypass paper feed pulley 5 Bypass separation pad
6 Left registration roller 7 Right registration roller 8 Drawer lift 9 Registration switch (RSW) 0 Bypass paper width switch (BYPPWSW)
Y102911-6
Service Manual
2-1-1
RMPCB
RM
RM
EPCB
YC1-4
RM
YC2-1,2,4,5
YC4-4
RSW
DPCB
RSW PFCL
YC5-12 YC2-1
YC1-9 YC1-15
RSW
YC8-9 YC8-3
PFCL
PFCL
BYPPFSOL
BYPPFSOL
YC3-2
YC1-13
BYPPFCL
YC8-5
PSW
PSW BYPPWSW
YC6-2
YC1-16
PSW
BYPPWSW
YC8-2
BYPPWSW
YC5-9
YC1-10
YC8-8
PLSW
PLSW
YC22-1,2,4
2-1-2
Service Manual
Y102911-6
Primary feed
Primary feed
PFCL
RSW
RM 330 ms Dev.BIAS
Separation charging
290 ms
10 ms
Timing chart 2-1-1 Paper feed from the drawer (A4, single-sided copy) a: b: c: d: The paper feed clutch (PFCL) turns on to start primary paper feed. 430 ms after the paper feed clutch (PFCL) turns on, the registration switch (RSW) turns on. 105 ms after the registration switch (RSW) turns on, the paper feed clutch (PFCL) turns off. 150 ms after the paper feed clutch (PFCL) turns on, the registration motor (RM) turns on to start secondary paper feed. e: 550 ms after the registration motor (RM) turns on, the paper feed clutch (PFCL) turns off. f: 1900 ms after the registration motor (RM) turns on, the registration switch (RSW) turns off. At the same time, the paper feed clutch (PFCL) turns on to start primary paper feed of the second sheet. g: 320 ms after the registration switch (RSW) turns off, the registration motor (RM) turns off.
Y102911-6
Service Manual
2-1-3
1 Mirror 1 frame 2 Mirror 2 frame 3 Exposure lamp (EL) 4 Mirror 1 5 Mirror 2 6 Mirror 3 7 Image scanning unit (ISU) 8 CCD PCB (CCDPCB) 9 Laser scanner unit (LSU) 0 Scanner home position switch (SHPSW) ! Original detection switch (ODSW) @ Original size detection sensor (OSDS)
2-1-4
Service Manual
Y102911-6
(1) Original scanning The original image is illuminated by the exposure lamp (EL) and scanned by the CCD PCB (CCDPCB) in the image scanning unit via the three mirrors, the reflected light being converted to an electrical signal. The scanner and mirror frames travel to scan on the optical rails on the front and rear of the machine to scan from side to side. The speed of the mirror frames is half the speed of the scanner. When the DP is used, the scanner and mirror frames stop at the DP original scanning position to start scanning.
Original
INPCB SM YC1-1,6
EL ON
MPCB
YC17-1,6
YC16 -1,2,3,4
YC7-1YC7-7
YC1-1YC1-7 YC2-2
SM
OSDS
OSDS
PDN
ODSW
ODSW
PDPCB
SHPSW
SHPSW
Y102911-6
Service Manual
2-1-5
(2) Image printing The image data scanned by the CCD PCB (CCDPCB) is processed on the main PCB (MPCB) and transmitted as image printing data to the laser scanner unit (LSU). By repeatedly turning the laser on and off, the laser scanner unit forms a latent image on the drum surface.
Drum
1 Laser diode: Generates the laser beam which forms a latent image on the drum. 2 Collimator lens: Collimates the diffused laser beam emitted from the laser diode to convert it into a cylindrical beam. 3 Cylindrical lens: Shapes the collimated laser beam to suit the printing resolution. 4 Polygon mirror: Six-facet mirror that rotates at approximately 23619 rpm with each face reflecting the laser beam toward the drum for one main-direction scan. 5 Polygon motor: Drives the polygon mirror. 6 F lens: Corrects for non-linearity of the laser beam scanning speed on the drum surface, keeps the beam diameter constant and corrects for the vertical alignment of the polygon mirror to ensure that the focal plane of the laser beam is on the drum surface. 7 F lens: Corrects for non-linearity of the laser beam scanning speed on the drum surface, keeps the beam diameter constant and corrects for the vertical alignment of the polygon mirror to ensure that the focal plane of the laser beam is on the drum surface. 8 PD sensor mirror: Reflects the laser beam to the PD sensor to generate the main-direction (horizontal) sync signal. 9 Cylindrical correcting lens: Corrects for the deviation of the laser beam reflected by the PD sensor mirror to the PD sensor. 0 PD sensor: Detects the beam reflected by the PD sensor mirror, outputting a signal to the main PCB (MPCB) to provide timing for the main-direction sync signal.
2-1-6
Service Manual
Y102911-6
Less than 85 m
Figure 2-1-6
Scanning in the main direction is provided by the rotating polygon mirror, while scanning in the auxiliary direction is provided by the rotating drum, forming a static latent image on the drum. The static latent image of the letter A, for example, is formed on the drum surface as shown in Figure 2-1-7. Electrical charge is dissipated on the area of the drum surface irradiated by the laser. The focal point of the laser beam is moved line by line, and adjacent lines slightly overlap each other.
: laser beam is on
Figure 2-1-7
Y102911-6
Service Manual
2-1-7
1 Drum 2 Main charger unit 3 Main charger wire 4 Drum separation claw 5 Cleaning roller 6 Cleaning spiral 7 Cleaning blade 8 Cleaning lamp (CL)
2-1-8
Service Manual
Y102911-6
CL
CL
YC3-7,8
MC Grid
YC1-8 YC1-12
MHVADJC MHVDRN
YC9-9 YC9-5
Drum
ZENER PCB
HVTPCB
EPCB
Timing chart 2-1-2 Main charging section operation a: The drive motor (DM) turns on at the same time, the cleaning lamp (CL) turns on. b: 100 ms after the drive motor (DM) turns on, main charging starts. c: 840 ms after the exit switch (ESW) off, main charging is completed. d: The drive motor (DM) turns off at the same time, the cleaning lamp (CL) turns off.
Y102911-6
Service Manual
2-1-9
1 Developing unit 2 Developing roller 3 Doctor blade 4 Left developing spiral 5 Right developing spiral 6 Toner container 7 Toner container sensor (TCS) 8 Toner container detection switch (TCDSW)
2-1-10
Service Manual
Y102911-6
(1) Formation of magnetic brush The developing roller consists of a magnet roller with four poles and a sleeve roller. Rotation of the sleeve roller around the magnet roller entrains toner, which in turn forms a magnetic brush at pole N1 on the magnet roller. The height of the magnetic brush is regulated by the doctor blade; the developing result is affected by the position of the poles on the magnet roller and the position of the doctor blade. A developing bias voltage generated by the high-voltage PCB (HVTPCB) is applied to the developing roller to provide image contrast.
Doctor blade A 94 S2 86
N1
N2
Developing roller
100 S1
A: Distance between the doctor blade and developing roller; 0.3 0.05 mm
Drum DB
HVTPCB EPCB DB
OFS
OFS
YC3-14
TCDSW
TCDSW
YC22-5
YC8-10
Y102911-6
Service Manual
2-1-11
(2) Single component developing system This machine uses the single component developing system, and reversal processing is performed with a + charged drum (a-Si) and a + charged magnetic toner. With the single component developing system, toner is electrically charged by friction with the developing sleeve and + charged when it passes through the magnetic doctor blade. The toner that has passed through the magnetic doctor blade forms a uniform layer on the developing sleeve. When the toner layer comes to the location where the developing sleeve is the nearest to the drum, toner moves between the drum and the developing sleeve by an electric field of the magnetic pole. Then, when the developing sleeve rotates and passes through the nearest location to the drum, on the portion of the drum that has been exposed to light, toner is attracted toward the drum by potential difference between the developing bias and the drum surface and development is performed. On the other hand, on the portion of the drum that has not been exposed to light, toner is attracted toward the sleeve and development is not performed. When toner comes to an area where the gap between the drum and the developing sleeve is large, an electric field disappears and toner does not leave the developing sleeve. Development is complete.
Drum
Figure 2-1-13 Single component developing system Developing bias parameters For the bias to the developing sleeve, an alternating current (AC) is applied. Parameters for the developing bias are shown below. Vp-p: Difference between the maximum and the minimum of applied voltage 1.6 kV (fixed) Vf: Frequency Typically 2.7 kHz. This value varies depending on the preset value of the drive time and the environmental correction. (Can be adjusted with the maintenance item U101.) Duty: Ratio of time where + voltage is applied in a cycle Typically 45%. (Can be adjusted with the maintenance item U101.) Vdc: Developing shift bias potential 290 V Supplementation Vo: Drum surface potential on non-image area (area not exposed to light) VL: Drum surface potential on image area (area exposed to light)
Duty
Vo Vdc VL 0
Vp-p
Vf
2-1-12
Service Manual
Y102911-6
Figure 2-1-15 Transfer and separation sections 1 Transfer roller 2 Separation electrode 3 Drum separation claw 4 Drum
SC
Transfer roller TC
YC1-4 HVTPCB
Y102911-6
Service Manual
2-1-13
Primary feed
Primary feed
PFCL 1900 ms 430 ms RSW 150 ms RM 330 ms Dev.BIAS 320 ms 150 ms 430 ms
Timing chart 2-1-3 Transfer and separation sections operation a: 290 ms after the registration motor (RM) turns on to start secondary paper feed, separation charging starts. b: 10 ms after separation charging starts, transfer charging starts. c: 670 ms after the registration switch (RSW) turns off, transfer charging ends. d: 100 ms after transfer charging ends, separation charging ends.
2-1-14
Service Manual
Y102911-6
1 Left fixing unit 2 Right fixing unit 3 Press roller 4 Heat roller 5 Fixing heater M (FH-M) 6 Fixing heater S (FH-S) 7 Heat roller separation claw 8 Fixing thermostat (FTS)
FH-M YC21-7
EPCB
Y102911-6
CN3-12
Service Manual
YC21-8
FH-S
FTH
2-1-15
Warm-up control
Time
500 ms
On On
Off Off
On On
Off Off
On On
Figure 2-1-19 Fixing temperature system Warm-up control 1. 500 ms after the fixing heater S (FH-S) turns on, the fixing heater M (FH-M) turns on. 2. When the fixing temperature reaches preset temperature, both fixing heater S (FH-S) and fixing heater M (FH-M) turn off simultaneously. Ready state control 1. When the fixing temperature drops to the preset temperature, fixing heater S (FH-S) turns on, and after specified time, the heater turns off. 2. When fixing heater S (FH-S) turns off, fixing heater M (FH-M) turns on at the same time, and after specified time, the heater turns off. 3. The operation above is repeated to keep the fixing temperature to the preset temperature. * If a temperature more than or equal to the preset temperature + 20C/68F is detected, both fixing heater S (FH-S) and fixing heater M (FH-M) are turned off forcibly. (2) Fixing temperature control based on ambient temperature This machine performs fixing temperature control based on the ambient temperature.
Ambient temperature Lower than 15C/59F Higher than or equal to 15C/59F, lower than 20C/68F Higher than or equal to 20C/68F, lower than 31C/78.8F Higher than 31C/78.8F Fixing temperature (C) Reference value +10 Reference value +5 Reference value Reference value -5
2-1-16
Service Manual
Y102911-6
1 Feedshift guide 2 Exit roller 3 Exit pulley 4 Feedshift guide 5 Switchback roller 6 Switchback pulley 7 Exit switch (ESW) 8 Feedshift switch (FSSW)
EM
EM
YC14-1,2,3,4
ESW
ESW
YC15-2
FSSW
FSSW
EPCB YC15-3
Y102911-6
Service Manual
2-1-17
1 Duplex feed pulley 2 Upper duplex feed roller 3 Duplex feed pulley 4 Lower duplex feed roller 5 Duplex paper conveying switch (DPPCSW)
DPCB
EPCB
DUPPCSW
DUPPCSW
YC5-5
YC1-11
DUPPCSW
YC8-7
DUPFCL
DUPFCL
YC5-8
YC1-12
DUPFCL
YC8-6
2-1-18
Service Manual
Y102911-6
(1) Paper conveying operation in duplex copying Paper of which copying onto the reverse side is complete is conveyed to the switchback section, the exit motor switches from forward rotation to reverse rotation to switch the exit roller to reverse rotation, and the paper conveying direction is reversed. Paper that has been switched back is conveyed to the duplex unit via the exit roller and the switchback roller. Paper that has been conveyed to the duplex unit is conveyed to the paper feed section again by rotation of the upper duplex feed roller and the lower duplex feed roller and copying onto the front side is performed.
Exit roller
Switchback roller
Exit roller
Exit roller
Lower duplex feed roller Copying onto reverse side (forward rotation of exit motor) Switchback operation (reverse rotation of exit motor) Copying onto front side (forward rotation of exit motor)
Paper path
Figure 2-1-24
Y102911-6
Service Manual
2-1-19
5 6
7 4 10 9
11
Machine front
Engine PCB (EPCB) .................................... Controls the other PCBs, electrical components and optional devices. Main PCB (MPCB) ....................................... Controls the operation panel and laser scanner unit. Power source PCB (PSPCB) ....................... Generates +24 V DC and 5V DC; controls the fixing heater. High-voltage PCB (HVTPCB) ...................... Main charging. Generates high voltages for transfer and high voltages for separation. Inverter PCB (INPCB) .................................. Controls the exposure lamp. CCD PCB (CCDPCB) .................................. Reads the image off originals. Operation unit PCB (OPCB) ........................ Consists of the operation keys and display LEDs. Drawer PCB (DPCB) ................................... Controls the electrical components. APC PCB (APCPCB) ................................... Generates and controls the laser light. PD PCB (PDPCB) ........................................ Controls horizontal synchronizing timing of laser beam. Registration motor PCB (RMPCB) ............... Controls the registration motor.
Machine inside
Machine rear
Y102911-6
Service Manual
2-2-1
10
12
13
17
18
16
15
11
14
7
Machine front
Machine inside
Machine rear
*: Optional
2-2-2
Service Manual
Y102911-6
(3) Motors
3 4
5 1 6
Machine front
1. Drive motor (DM) ......................................... Drives the machine. 2. Scanner motor (SM) .................................... Drives the optical system. 3. Exit motor (EM) ............................................ Drives the exit section. 4. Cooling fan motor 1 (CFM1) ........................ Cools the machine interior. 5. Cooling fan motor 2 (CFM2) ........................ Cools the machine interior. 6. Polygon motor (PM) ..................................... Drives the polygon mirror. 7. Registration motor (RM) ............................... Drives the registration roller.
Machine inside
Machine rear
Y102911-6
Service Manual
2-2-3
6 5 7
8 1
Machine front
Figure 2-2-4 Other electrical components 1. 2. 3. 4. 5. 6. 7. 8. 9. Paper feed clutch (PFCL) ............................ Primary paper feed from the drawer. Bypass paper feed solenoid (BYPPFSOL) .. Primary paper feed from the bypass tray. Exposure lamp (EL) ..................................... Exposes originals. Cleaning lamp (CL) ...................................... Removes residual charge from the drum surface. Fixing heater M (FH-M) ................................ Heats the heat roller. Fixing heater S (FH-S) ................................. Heats the heat roller. Fixing thermostat (FTS) ............................... Prevents overheating in the fixing section. Drawer heater (DH)* .................................... Dehumidifies the drawer section. Duplex feed clutch (DUPFCL)* .................... Controls the drive of the duplex feed roller.
Machine inside
Machine rear
2-2-4
Service Manual
Y102911-6
F001 FG
C204
GND F003 DH1.LIVE DH2.LIVE DH1.OUT DH2.OUT Fixing heater control circuit SH.OUT MH.OUT Ficing heater ON/OFF circuit (TR001,TR002) PC004 PC005 Energy save control circuit S.HEATN M.HEATN AC detection circuit Overvoltage detection circuit (IC201) DC5V 3 terminal regulator (IC301) Zero-cross output circuit
+5V1
ZCROSS
PC003
SLEPN
The power source PCB (PSPCB) is a switching regulator that converts an AC input to generate 24 V DC and 5 V DC. It includes a rectifier circuit, a switching regulator circuit, a 24 V DC output circuit, a 5 V DC output circuit, overvoltage detection circuit, zero-cross circuit and a fixing heater control circuit. The rectifier circuit full-wave rectifies the AC input using the diode bridge D005. The smoothing capacitor (C008) smoothes out the pulsed current from the diode bridge. In the switching control circuit, PWM controller (IC001) turns the power MOSFET (Q006) on and off to switch the voltage induced in the primary coil of the transformer (T001). The 5 V DC output circuit rectifies and smoothes the voltage induced in the secondary coil of the transformer (T001) via diodes (D206) and smoothing capacitors (C204), and the output is controlled by the overvoltage detection circuit (IC201). For 5 V DC output, the PWM controller IC (IC001) of the switching control circuit changes the duty of the switching pulse width of the power MOSFET (Q006) via a photo coupler (PC001) based on the output voltage status to adjust the 5 V DC output. The 24 V DC output circuit rectifies and smoothes the voltage induced in the secondary coil of the transformer (T001) via diodes (D201) and smoothing capacitors (C102), and the output is controlled by the overvoltage detection circuit (IC201). The zero-cross circuit detects zero-crossing of the AC input voltage with the AC detection circuit and outputs the zero-cross signal (ZCROSS) from the zero-cross output circuit through the photo coupler (PC002). The fixing heater control circuit is divided into the sub-heater output (SH. OUT) and the main heater output (MH. OUT). When the control signals (S. HEATN and M. HEATN) input from the machine engine side show a low level, this circuit turns on the sub-heater and the main heater respectively by turning on the photo triac couplers (PC004 and PC005) with a zerocross circuit to turn on the triacs (TR001 and TR002) in the fixing heater ON/OFF circuit. The power-saving control circuit performs power-saving control by turning off the 24 V DC output in the 24 V DC output ON/ OFF switching circuit and controlling the switching control circuit and the AC detection circuit through the photo coupler (PC003) to decrease the switching frequency, stop the starting circuit in the switching control circuit, and stop the AC detection circuit when the sleep signal (SLEPN) input from the machine engine side is low. In addition, 5 V DC three-terminal Reg is connected to the back of the 24 V DC output ON/OFF switching circuit to output +5 V1, and this output stops when the sleep signal (SLEPN) is low.
Y102911-6
Service Manual
2-3-1
Q206
Q101
C104
1 1
C008 PC005 PC004 D005 C006 L004 TR001 TR002 3 L003 L001 C027 YC7 YC8 1 1 L012 F003 F002 C003 L013 F001 SW001 4 4 C017 T001 C102 Q006 C204 F201 IC301 C301 1 L102 D101
YC2
14
YC1
17 2
YC6
Connector Pin No. IL001 Connected to the AC power plug YC1 Connected to the engine PCB and left cover safety switch YC2 Connected to the engine PCB 1 2 3
Description
1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 10 11 12 13 14
+24 V1 NC +24 V2 +24 V4 P.GND S.GND +5 V +5 V S.GND +24 V2 S.GND ZCROSS SLEPN S.HEATN M.HEATN COUNTN P.GND P.GND +24 V1 +24 V1 +24 V
O I O O O I O I I I I O O O
24 V DC power supply for LCSSW Not used 24 V DC power supply 24 V DC power supply for EPCB Ground Ground 5 V DC power supply for EPCB 5 V DC power supply for EPCB Ground 24 V DC power supply Ground Zero-cross signal Power source sleep signal FH-S on/off FH-M on/off Counter control signal Ground Ground 24 V DC power supply for EPCB 24 V DC power supply for EPCB 24 V DC power supply for EPCB
2-3-2
Service Manual
Y102911-6
Connector Pin No. Signal YC5 1 +5 V1 2 NC Connected 3 +5 V3 to the front cover safety switch YC6 Connected to the fixing heater M/S YC7 Connected to the optional paper feeder YC8 Connected to the drawer heater* YC9 Connected to the optional paper feeder 1 2 3 H.LIVE MH.OUT MH.OUT
I/O O I
O O O
AC power supply for FH-M/S (LIVE) AC power supply for FH-M AC power supply for FH-S
1 2 3 4
DH2.LIVE NC NC DH2.OUT
O O
AC power supply for drawer heater of the paper feeder (LIVE) Not used Not used AC power supply for drawer heater of the paper feeder
1 2 3 4
DH1.LIVE NC NC DH1.OUT
O O
AC power supply for drawer heater (LIVE) Not used Not used AC power supply for drawer heater
1 2
+24 V4 P.GND
O -
Y102911-6
Service Manual
2-3-3
CCDPCB
12V
5V
EPCB
MPCB SBSY SDIR EGIRN RSTN EGSO SCKN EGSI PDMASKN OVSYNK OUTPEN PLGCLK ASIC
LSU PLGCLK PLGDR PLGRDYN OUTPEN VDATAN PDN SAMPLEN 5V1 24V4
2-3-4
Service Manual
Y102911-6
U4 1 YC7 U18 7 2 1
YC1 12 18 13 17
YC8 2 1
U5
1 2
U30
U32
U9
1 YC2
YC5
X1
YC3
U19
1 17 2 18
X4
12
U13
U20
U21
U8
YC4
X3
1 YS1
100
U7
U6
1 YS2
72
YC8
U24 U26
9 10
U27
U10
U12
Y102911-6
Service Manual
22
2-3-5
Connector Pin No. YC4 1 2 Connected 3 to the 4 operation 5 unit PCB 6 7 8 9 10 YC5 Connected to the operation unit PCB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1 2 3 4 5 6 7
Signal +5 V BUZERDRN SCAN7N SCAN6N SCAN5N SCAN4N SCAN3N SCAN2N SCAN1N SCAN0N LED0 LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 LED9 LED10 LED11 LED12 KEY0 KEY1 KEY2 KEY3 KEY4 +12 V OVSYNC RSTN EGRN SDIR SBSY PDMASKN EGSI SCKN EGSO PLGCLK S.GND OUTEPN +5 V +5 V +5 V S.GND S.GND S.GND +5 V3 P.GND +24 V PDN S.GND OUTPEN SAMPLEN VDON VDOP +5 V3
I/O O O O O O O O O O O O O O O O O O O O O O O O I I I I I I I I I I I I O O I O I I I I I I I O O O O O
Description 5 V DC power supply for OPCB OPCB buzer signal Key switch scan signal 7 Key switch scan signal 6 Key switch scan signal 5 Key switch scan signal 4 Key switch scan signal 3 Key switch scan signal 2 Key switch scan signal 1 Key switch scan signal 0 LED lighting selection signal 0 LED lighting selection signal 1 LED lighting selection signal 2 LED lighting selection signal 3 LED lighting selection signal 4 LED lighting selection signal 5 LED lighting selection signal 6 LED lighting selection signal 7 LED lighting selection signal 8 LED lighting selection signal 9 LED lighting selection signal 10 LED lighting selection signal 11 LED lighting selection signal 12 Key switch return signal 0 Key switch return signal 1 Key switch return signal 2 Key switch return signal 3 Key switch return signal 4 12 V DC power supply from EPCB Original scanning interval signal Reset signal Enginge communication EGRN signal Enginge communication SDIR signal Enginge communication SBSY signal Printing image interval signal Enginge serial communication transmission Enginge communication clock signal Enginge serial communication reception PM clock signal Ground Laser diode output signal 5 V DC power supply from EPCB 5 V DC power supply from EPCB 5 V DC power supply from EPCB Ground Ground Ground 5 V DC power supply from EPCB Ground 24 V DC power supply from EPCB Laser sync signal Ground Laser diode output signal Laser light signal Image differential signal (negative) Image differential signal (positive) 5 V DC power supply for APCPCB
2-3-6
Service Manual
Y102911-6
Signal CCDO CCDON CCDE CCDEN +5 V S.GND +12 V S.GND CCDCLK S.GND CCDCLKN S.GND RS S.GND CP S.GND SH S.GND
I/O I I O O O O O O O -
Description CCDPCB image scanning signal Ground CCDPCB image scanning signal Ground 5 V DC power supply for CCDPCB Ground 12 V DC power supply for CCDPCB Ground CCDCLK signal Ground CCDCLKN signal Ground CCDPCB RS signal Ground CCDPCB CP signal Ground CCDPCB SH signal Ground
Y102911-6
Service Manual
2-3-7
CFM1,2
FAN1N FAN1LOW FAN2N FAN2LOW
PSPCB
ILOCK ILOCKL SLEPN
HVTPCB
MHVDR THVDR SHVDR SHVISEL HVCLK (DB) MHVIADJ THVIADJ 24V4 5V
INPCB
LAMPN 24V1
DP
ORGTIM DOPSEL,DOPRDY DOPSI,DOPSO DOPSCLK
CL
ERASER 24V4
24V1
ISU
5V
24V1
5V
TONEEPY TONEFUL
Scanner unit
OPSWN ORGLSWN 5V2 5V2
ISU
CCDPCB
5V2
Duplex unit
24V1
12V 24V1
5V
EPCB MPCB
5V 3.3V 2.5V
Fixing unit
5V
SBSY SDIR EGIRN RSTN EGSO SCKN EGSI PDMASKN OVSYNK OUTPEN PLGCLK
CPU
24V4
ASIC
DM
MDMREMN MDMCLKN MDMRDY
RSW ESW
REGSWN EXTSWN
BYPPWSW
BPWSW BPPESW
PLSW PWSW
C1PLSW1N C1PLSW2N C1PLSW3N C1PWSWN C1PDSW 5V2
RM
RMENB RMLOW RMENB
LSU
PLGCLK PLGDR PLGRDYN OUTPEN VDATAN PDN SAMPLEN 5V1 24V4
24V4 5V
24V4
24V4 5V2
5V2
5V2
5V
2-3-8
Service Manual
Y102911-6
YC16 1 4
6 YC17 1
3 1 YC6 12
YC18 6
1
YC19 1
U13
YC4
13 YC15 1 4 1
U10
U9
U8
YC12
U6
YC5
U15 U12
U1 X1 1 YC1 YC2 4 YC13 22 YC23 1 1 7 4 2
U11
YC21
U16
14
4 YC20 1
U7
YC10
YC24
11
YC8
17
6 YC22 1
YC9
16
Y102911-6
Service Manual
YC11
YC7
15
YC3
YC14
2-3-9
Connector Pin No. 1 YC1 2 Connected 3 to the Main 4 PCB 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 YC2 Connected to the polygon motor, cleaning lamp, cooling fan motor 1, fixing thermister and overflow sensor YC4 Connected to the registration motor PCB YC6 Connected to the optional DP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 2 3 4 5 1 2 3 4 5 6 7 8 9 10 11 12
Signal +12 V OVSYNC RSTN EGRN SDIR SBSY PDMASKN EGSI SCKN EGSO PLGCLK S.GND OUTEPN +5 V +5 V +5 V S.GND S.GND S.GND +5 V3 P.GND +24 V PLGCLKN PLGRDYN PLGDRN PLGGND PLG +24 V4 ERASE +24 V4 ERASE2N ERASE1N FAN1DRN +24V1 THERMA +5 V THERMA TONEGND TONEFUL TONE +5 V2 +5 V RMLOW RMCLK RMENB S.GND ORGTIMN DOPRDY DOPSEL S.GND DOPCLK DOPSDI DOPSDO +5 V4 P.GND P.GND +24V1 +24V1
I/O O O O O O O O I I O I O O O O O O O I O O O O O O O O I I O O O O O I I O O I O O O O
Description 12 V DC power supply for MPCB Original scanning interval signal Reset signal Enginge communication EGRN signal Enginge communication SDIR signal Enginge communication SBSY signal Printing image interval signal Enginge serial communication reception Enginge communication clock signal Enginge serial communication transmission PM clock signal Ground Laser diode output signal 5 V DC power supply for MPCB 5 V DC power supply for MPCB 5 V DC power supply for MPCB Ground Ground Ground 5 V DC power supply for APCPCB/PDPCB Ground 24 V DC power supply for MPCB PM clock signal PM rotation sync signal PM on/off Ground 24 V DC power supply for PM 24 V DC power supply for CL CL on/off (2) CL on/off (1) CFM1 on/off 24 V DC power supply for CFM1 5 V DC power supply for FTH FTH analog signal Ground OFS on/off 5 V DC power supply for OFS 5 V DC power supply for RM RM Low signal Rm clock signal RM on/off Ground DP original scanning interval signal DP READY signal DP SEL signal Ground DP clock signal DP serial communication reception DP serial communication transmission 5 V DC power supply for DP Ground Ground 24 V DC power supply for DP 24 V DC power supply for DP
2-3-10
Service Manual
Y102911-6
Connector Pin No. YC7 1 2 Connected 3 to the drive 4 motor 5 6 7 YC8 Connected to the drawer PCB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 1 2
Signal +24V4 P.GND S.GND +5 V REM RDY CLK BPPESW C1PDSWN FCLTN +24V1 BPSOLN ICLTN IPPSWN BPWSW REGSWN TONEPY S.GND +5 V2 C1PWSWN HUMIDC HMCLK2 HMCLK1 TEMP HVCLK +5 V SHVISELN P.GND MHVDRN P.GND SHVDRN P.GND MHVADJ P.GND THVDRN +24 V4 THVADJ +24 V4 P.GND +24 V4 LOPSRDY LOPSEL2 LOPSEL1 LOPSEL0 LOPSCLK LOPSDI LOPSDO S.GND +5 V2 S.GND +5 V2 +24 V4 FAN2DRN
I/O O O O I O I I O O O O I I I I O I I O O I O O O O O O O O O O O I O O O O I O O O O O
Description 24 V DC power supply for DM Ground Ground 5 V DC power supply for DM DM on/off DM rotation sync signal DM clock signal BYPPSW on/off PSW on/off PFCL on/off 24 V DC power supply for DPCB BYPPFCL on/off DUPFCL on/off DUPPCSW on/off BYPPWSW on/off RSW on/off TCS on/off Ground 5 V DC power supply for DPCB PWSW on/off HUMSENS analog signal HUMSENS clock signal (2) HUMSENS clock signal (1) HUMSENS analog signal Developing bias clock signal 5 V DC power supply for HVTPCB Separation high-voltage switch siganl Ground Main charging high-voltage on/off Ground Separation high-voltage on/off Ground Main charging high-voltage adjust siganl Ground Transfer high-voltage on/off 24 V DC power supply for HVTPCB Transfer high-voltage adjust siganl 24 V DC power supply for HVTPCB Ground 24 V DC power supply for HVTPCB Paper feeder READY signal Paper feeder SEL2 signal Paper feeder SEL1 signal Paper feeder SEL0 signal Paper feeder clock signal Paper feeder serial communication reception Paper feeder serial communication transmission Ground 5 V DC power supply for the paper feeder Ground 5 V DC power supply for the paper feeder 24 V DC power supply for CFM2 CFM on/off
Y102911-6
Service Manual
2-3-11
Connector Pin No. YC13 1 2 Connected 3 to the key 4 counter YC14 Connected to the exit motor YC15 Connect to the exit switch and feedshift switch YC16 Connected to the scanner motor YC17 Connected to the inverter PCB YC18 Connected to the original detection switch and scanner home position switch YC19 Connected to the original size detection sensor YC20 Connected to the power source PCB YC21 Connected to the power source PCB 1 2 3 4 1 2 3 4
Signal +24 V1 KEYCN S.GND KEYENBN COMDA COMDNB COMDNA COMDB P.GND EXTSMN SEPSWN +5 V2
I/O O O I O O O O I I O
Description 24 V DC power supply for key counter Key counter count signal Ground Key counter set signal EM control signal (A) EM control signal (_B) EM control signal (_A) EM control signal (B) Ground ESW on/off FSSW on/off 5 V DC power supply for ESW/FSSW
1 2 3 4
O O O O
SM control signal (A) SM control signal (_B) SM control signal (_A) SM control signal (B)
1 2 3 4 5 6 1 2 3 4 5 6
LAMPN P.GND +24 V1 +24 V1 P.GND LAMPN +5 V2 HPSWN S.GND +5 V2 OPSWN S.GND
O O O O O I O I -
EL on/off Ground 24 V DC power supply for inverter PCB 24 V DC power supply for inverter PCB Ground EL on/off 5 V DC power supply for SHPSW SHPSW on/off Ground 5 V DC power supply for ODSW ODSW on/off Ground
1 2 3
+5 V2 ORGLSWN S.GND
O I -
1 2 3 4
I I
5 V DC power supply from PSPCB Ground Ground 24 V DC power supply from PSPCB
1 2 3 4 5 6 7 8
I I I O O
24 V DC power supply from PSPCB 24 V DC power supply from PSPCB 24 V DC power supply from PSPCB Ground Ground Not used FH-M on/off FH-S on/off
2-3-12
Service Manual
Y102911-6
Connector Pin No. YC21 9 10 Connected 11 to the 12 power 13 source PCB 14 YC22 Connected to the paper size length switch and toner container detection switch YC24 Connected to the registration motor PCB 1 2 3 4 5 6
Signal SLEPN ZCROSS S.GND +24 V2 S.GND +5 V3 C1PLSW3N C1PLSW2N S.GND C1PLSW1N TCONDET S.GND
I/O O O I I I I I I -
Description Power source sleep signal Zero-cross signal Ground LCSSW on/off Ground FCSSW on/off PLSW on/off PLSW on/off Ground PLSW on/off TCDSW on/off Ground
1 2 29
O -
Y102911-6
Service Manual
2-3-13
K10 K9 K8 K7 K6
+5V
K35 U1
10 6 1 11 7 2 13 8 4 15 20 24 16 21 25
YC1
+5V BUZERDRN SCAN7N SCAN6N SCAN5N SCAN4N SCAN3N SCAN2N SCAN1N SCAN0N
D2
1 1
D3
1
D4
1
D5
1
D6
1
D7
1
D8
e3 e2 e1 d3 d2 d1 c3 c2 c1 b3 b2 b1 a3 a2 a1
27 23 17 28 22 12 5 9 14 3 26 19 18
YC2
KEY4 KEY3 KEY2 KEY1 KEY0 LED12 LED11 LED10 LED9 LED8 LED7 LED6 LED5 LED4 LED3 LED2 LED1 LED0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
7 segment L37 L9 L8 L7 L6 L5 L18 L17 L16 L15 L14 L13 L3 L2 L1 L12 L11 L10 L27 L26 L25 L24 L23 L22 L21 L20 L19 L36 L35 L34 L33 L32 L31 L30 L29 L28 L75 L46 L45 L44 L43 L42 L41 L40 L39 L38 L55 L54 L53 L52 L51 L50 L49 L48 L47 L56 L64 L63 L62 L61 L60 L59 L58 L74 L73 L72 L71 L70 L69 L68 L67 L66 L65 LED
Figure 2-3-7 Operation unit PCB block diagram The operation unit PCB (OPPCB) consists of key switches, LEDs, 7 segment LED and buzer. The lighting of LEDs is determined by scan signals (SCAN0 to SCAN7) and LED lighting selection signals (LED0 to LED12) from the main PCB (MPCB). The key switches operated are identified by the scan signals (SCAN0 to SCAN7) and the return signals (KEY0 to KEY4). As an example, to light L1, the LED lighting selection signal (LED0) should be driven low in synchronization with a low level on the scan signal (SCAN0). LEDs can be lit dynamically by repeating such operations. As another example, if K1 is pressed, the corresponding key switch is turned on feeding the low level of the scan signal (SCAN0) back to the main PCB (MPCB) via the return signal (KEY0). The main PCB (MPCB) locates the position where the line outputting the scan signal and the line inputting the return signal cross, and thereby determines which key switch was operated.
2-3-14
Service Manual
Y102911-6
Y102911-6
L28 L56 L58 L47 L64 L63 K17 K19 K24 L44 L45 L46 L35 K11 K13 K14 K15 K10 L74 L73 L72 L71 L70 L69 K18 K25 K30 K34 K38 K29 K33 L68 K16 L29 L36 YC2 L65 K20 K22 YC1 L37 K21 K27 L66 K26 K31 L67 K35 K36 L27 L26 L25 L24 L23 K9 L59 L60 L61 L62 K12 L51 L50 L49 L48 L52 L53 L54 L55 L38 L39 L40 L41 L42 L43 L30 L31 L32 L33 L34 K23 K28 K32 K37 L75
L1 L2 L3
K1
K6
L4 L5
L13 L14
K2
K7
Service Manual
L6 L7
L15 L16
K3
K8
L8
L9
K4
K5
2-3-15
Connector Pin No. YC1 1 2 Connected 3 to the main 4 PCB 5 6 7 8 9 10 YC2 Connected to the main PCB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
Signal SCAN0N SCAN1N SCAN2N SCAN3N SCAN4N SCAN5N SCAN6N SCAN7N BUZERDRN +5 V KEY4 KEY3 KEY2 KEY1 KEY0 LED12 LED11 LED10 LED9 LED8 LED7 LED6 LED5 LED4 LED3 LED2 LED1 LED0
I/O I I I I I I I I I I O O O O O I I I I I I I I I I I I I
Description Key switch scan signal 0 Key switch scan signal 1 Key switch scan signal 2 Key switch scan signal 3 Key switch scan signal 4 Key switch scan signal 5 Key switch scan signal 6 Key switch scan signal 7 OPCB buzer signal 5 V DC power supply from MPCB Key switch return signal 4 Key switch return signal 3 Key switch return signal 2 Key switch return signal 1 Key switch return signal 0 LED lighting selection signal 12 LED lighting selection signal 11 LED lighting selection signal 10 LED lighting selection signal 9 LED lighting selection signal 8 LED lighting selection signal 7 LED lighting selection signal 6 LED lighting selection signal 5 LED lighting selection signal 4 LED lighting selection signal 3 LED lighting selection signal 2 LED lighting selection signal 1 LED lighting selection signal 0
2-3-16
Service Manual
Y102911-6
2-3-5
CCD PCB
CCDPCB Tr.AMP
The CCD PCB (CCDPCB) is equipped with a CCD sensor (U2) for original scanning. The clock signals for driving the CCD sensor (U2) are sent from the main PCB (MPCB), and then input to the CCD sensor (U2) via the clock driver (U1 and U3). Image signals are analog signals. Even- and odd-numbered pixels are output separately. These analog image signals are amplified in the transistors (TR1 to 4) and then transmitted to the analog signal processing circuit in the main PCB (MPCB).
Y102911-6
Service Manual
2-3-17
U2 YC1 U3 U4 U1
Signal S.GND SH S.GND CP S.GND RS S.GND CCDCLKN S.GND CCDCLK S.GND +12 V S.GND +5 V CCDEN CCDE CCDON CCDO
I/O I I I I I I I O O
Description Ground MPCB SH signal Ground MPCB CP signal Ground MPCB RS signal Ground CCDCLKN signal Ground CCDCLK signal Ground 12 V DC power supply from MPCB Ground 5 V DC power supply from MPCB Ground CCDPCB image scanning signal Ground CCDPCB image scanning signal
2-3-18
Service Manual
Y102911-6
Y102911-6
Scondary feed 250 ms Primary feed 105 ms Scondary feed 250 ms
1810 ms (20cpm machine) 1900 ms (16cpm machine)
Timing chart No. 1 Paper feed from drawer, single-side mode, original size A4/11" 81/2", two sheets
Primary feed
105 ms
PFCL
YC8-3
430 ms 430 ms
YC8-9 150 ms
RM
YC4-4
330 ms
Service Manual
290 ms 10 ms 670 ms 2020 ms
Dev.BIAS
290 ms
Transfer charging
YC9-11
ESW
YC15-2
2-4-1
Timing chart No. 2 Paper feed from drawer, single-side mode, original size A3/11" 17", two sheets
2-4-2
Scondary feed 1100 ms Primary feed 120 ms Scondary feed 1100 ms
2510 ms (20cpm machine) 2700 ms (16cpm machine)
Primary feed
120 ms
PFCL
YC8-3
2700 ms
434 ms 434 ms
RSW 320 ms
YC8-9
320 ms
RM
YC4-4
330 ms
330 ms
Service Manual
290 ms 290 ms
100 ms 10 ms 670 ms 2015 ms
Dev.BIAS
100 ms
10 ms
670 ms
Transfer charging
YC9-11
1800 ms
ESW
YC15-2
Y102911-6
Paper feed from optional first paper feeder, single-side mode, original size A4/11" 81/2", two sheets
Y102911-6
1740 ms 150 ms 290 ms 150 ms 290 ms 290 ms 100 ms 10 ms 670 ms 10 ms 2220 ms
Primary feed
200 ms
DPFCL1*
DDM1*
1740 ms
RSW
YC8-9
Service Manual
RM
YC4-4
Transfer charging
YC9-11
ESW
YC15-2
*: Optional
2-4-3
2-4-4
200 ms Scondary feed Scondary feed Primary feed 200 ms 1420 ms 1370 ms 150 ms 290 ms 150 ms 290 ms 100 ms 290 ms 10 ms 670 ms 10 ms 2220 ms
Paper feed from optional second paper feeder, single-side mode, original size A4/11" 81/2", two sheets
Primary feed
DPFCL2*
DDM2*
1420 ms
DFSW1*
DDM1*
1370 ms
RSW
YC8-9
Service Manual
RM
YC4-4
Transfer charging
YC9-11
ESW
YC15-2
*: Optional
Y102911-6
Y102911-6
Drive motor speed adjustment U053 Exp.1 (light) U053 test pattern 1-4-10 Adjusting the LSU print start timing U034 Exp.2 (light) U034 test pattern 1-6-14 Adjusting the LSU print start timing U034 Exp.1 (light) U034 test pattern 1-6-14 To make an adjustment for duplex copying, select exp.1 (flashing). Registration motor turning on timing (secondary paper feed start timing) U034 Exp.2 (light) U034 test pattern 1-6-12 Registration motor turning on timing (secondary paper feed start timing) U034 Exp.1 (light) U034 test pattern 1-6-12 To make an adjustment for duplex copying, select exp.1 (flashing). LSU illumination start timing U402 Exp.1 (light) U402 test pattern 1-6-15 LSU illumination end timing U402 Exp.3 (light) U402 test pattern 1-6-15
Adjusting order
Item
Image
Service Manual
Adjusting the leading edge registration of the bypass tray (printing adjustment)
2-4-5
2-4-6
Description Item No. Exposure indicator U402 Exp.2 (light) U402 test pattern 1-6-15 Original Page Remarks LSU illumination start/end timing Maintenance mode Data processing U065 Exp.1 (light) Test chart 1-6-28 No adjustment for copying using the DP. Original scanning speed U065 U070 Exp.2 (light) Test chart 1-6-28 1-4-13 U065: For copying an original placed on the contact glass. U070: For copying originals from the DP. Adjusting the original scan data (image adjustment) U067 U072 Test chart 1-6-31 1-4-15 U067: For copying an original placed on the contact glass. U072: For copying originals from the DP. 1-6-30 1-4-14 Original scan start timing U066 U071 Test chart U066: For copying an original placed on the contact glass. U071: For copying originals from the DP. Test chart 1-6-32 1-4-36 Adjusting the original scan data (image adjustment) U403 U404 Exp.2 (light) Exp.2 (light) U403: For copying an original placed on the contact glass. U404: For copying originals from the DP. Adjusting the original scan data (image adjustment) U403 U404 Exp.4 (light) Exp.4 (light) Test chart 1-6-32 1-4-36 U403: For copying an original placed on the contact glass. U404: For copying originals from the DP. U403 U404 Test chart 1-6-32 1-4-36 Adjusting the original scan data (image adjustment) Exp.1 (light) /Exp.3 (light) Exp.1 (light) /Exp.3 (light) U403: For copying an original placed on the contact glass. U404: For copying originals from the DP.
Adjusting order
Item
Image
Adjusting magnification of the scanner in the main scanning direction (scanning adjustment)
Adjusting magnification of the scanner in the auxiliary scanning direction (scanning adjustment)
Service Manual
Y102911-6
Y102911-6
When maintenance item U092 (Adjusting the scanner automatically) is run using the specified original (P/N 2A068020), the following adjustments are automatically made: Adjusting the scanner center line (U067) Adjusting the scanner magnification in the main scanning direction (U065) Adjusting the scanner leading edge registration (U066) Adjusting the scanner magnification in the auxiliary scanning direction (U065) Adjusting margins for reading an original on the contact glass (U403) When maintenance item U074 (Adjusting the DP automatically) is run using the specified original (P/N 2AC68241), the following adjustments are automatically made: Adjusting the DP magnification (U070) Adjusting the DP scanning timing (U071) Adjusting the DP center line (U072) Adjusting margins for DP original reading (U404)
Image quality
Enlargement/reduction
Lateral squareness
Margins
Service Manual
Specifications Copier: 0.8% Using DP: 1.5% Copier: 1.0% Using DP: 2.0% Copier: 1.5 mm/375 mm Using DP: 3.0 mm/375 mm A: 3.0 2.5 mm B: 3.0 2.5 mm C: 3.0 2.5 mm D: 3.0 2.5mm Drawer: 2.5 mm Bypass: 2.5 mm Duplex copying: 2.5 mm Drawer: 1.5 mm or less Bypass: 1.5 mm or less Duplex copying: 2.0 mm or less Drawer: 2.0 mm Bypass: 2.0 mm Duplex copying: 3.0 mm
2-4-7
2-4-8
Service Manual
Y102911-6
Maintenance part/location Paper feed pulley Separation pulley Forwarding pulley Bypass paper feed pulley Bypass separation pad Left registration roller Right registration roller Registration cleaner Trans guide film
Method Clean or replace Clean or replace Clean or replace Clean or replace Clean or replace Clean or replace Clean Clean or replace Check or replace -
Maintenance cycle
Clean with the alcohol. Clean with the alcohol. Clean with the alcohol. Clean with the alcohol. Clean with the alcohol.
Clean with alcohol or a dry cloth. Clean with alcohol or a dry cloth. Vacuum.
Points and cautions Clean with alcohol and then a dry cloth. Clean with alcohol and then a dry cloth. Clean with alcohol and then a dry cloth only if vertical black lines appear on the copy image. Clean with alcohol and then a dry cloth only if vertical black lines appear on the copy image. Clean with alcohol and then a dry cloth only if vertical black lines appear on the copy image. Clean with alcohol and then a dry cloth only if vertical black lines appear on the copy image. Replace if an image problem occurs or after the exposure lamp does not turn on. Check noise and shifting and then apply scanner rail grease EM-50E. Clean with alcohol or a dry cloth.
Page
Clean
Lens
Clean
Reflector
Clean
Exposure lamp
Clean or replace
1-6-17
Optical rail
Grease
Clean
Maintenance cycle
Points and cautions Vaccum or clean with a dry cloth. Clean with the equipped brush.
Page 1-6-37
Y102911-6
Service Manual
2-4-9
Maintenance cycle
Page 1-6-36
Page 1-6-33
Maintenance part/location Fixing unit Heat roller Press roller Heat roller separation
Maintenance cycle
Points and cautions Replace if the problem occurs. Clean with alcohol. Clean with alcohol. Clean with alcohol. Replace if it is being lacking, deformed or rubbing.
Maintenance part/location Exit roller Exit pulley Switchback roller Switchback pulley
Maintenance cycle
Points and cautions Clean with alcohol or a dry cloth. Clean with alcohol or a dry cloth. Clean with alcohol or a dry cloth. Clean with alcohol or a dry cloth.
Page
Section Covers
Method Clean
Page
Section Other
Page
2-4-10
Service Manual
Y102911-6
Y102911-6
Service Manual
2-4-11
8
INPCB EL SM 1/2 3/4 5/6
12 11 10 9 8 7 6 5 4 3 2 1
1 2 3 4
YC3
YC16
YC8
YC2 BK LAMPN/PGND +24V1/+24V1 PGND/LAMPN SGND 3 ORGLSWN 2 +5V2 1 YC6 +5V4 SGND 8 4 8 4 1 2 3 YC5
YC17
KMDET 1 NO 2 KMDREQ 3 KMACK 4 KMRXD 5 SGND 6 KMTXD 7 SGND 8 SGND 9 SGND 10 +5V 11 +5V 12
YC7
1 2 3 4 5 6 7
OE LB YW PK GN BE GY
7 6 5 4 3 2 1
YC1
3 2 1
YC2
3 2 1
1 2 3
1 2 3
1 2 NC 3 NC 4
1 2 NC 3 NC 4
YC8
YC7
YC9
1 +24V1 2 PGND
BPPE SW C1PDSWN FCLTN +24V1 BPSOLN ICLTN IPPSWN BPWSW REGSWN TONEPY SGND +5V2 C1PWSWN HUMIDC HMCLK2 HMCLK1 TEMP
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
WE WE WE WE
WE WE WE WE WE WE WE
YC1
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
1 NC 2 NC 3 4 5 6
DH (OPTION)
BK BE RD WE
1 2 3 4 5 6 7
1 2 3 1 2 3 4 B1 B2 B3 B4 B5 B6 A1 A2 A3 A4 A5 A6 A7
1 2 3
BYPPCSW
Y102911-6
CCDPCB OPTION KMAS (ONLY JAPAN) 1 2 3 LAMP N.C. LAMP
A
YC19 WE WE WE 3 2 1 WE WE WE 3 2 1 YC6 YC1 OPCB
OSDS
B
GY SCAN0N/SCAN1N SCAN2N/SCAN3N SCAN4N/SCAN5N SCAN6N/SCAN7N BUZERDRN/+5V MPCB EPCB
18/17 16/15 14/13 12/11 10/9 8/7 6/5 4/3 2/1 YC1 1/2 3/4 5/6 7/8 9/10 22/21 20/19 18/17 16/15 14/13 12/11 10/9 8/7 6/5 4/3 2/1 22/21 20/19 18/17 16/15 14/13 12/11 10/9 8/7 6/5 4/3 2/1 +24V/PGND +5V3/SGND SGND/SGND +5V/+5V +5V/OUTEPN SGND/PLGCLK EGSO/SCKN EGSI/PDMASKN SBSY/SDIR EGRN/RSTN OVSYNC/+12V DOPSDI DOPSDO DOPCLK DOPSEL DOPRDY ORGTIMN 6 7 5 3 2 1 PGND 9 PGND 10 +24V1 11 +24V1 12
1/2 3/4 5/6 7/8 9/10 11/12 13/14 15/16 17/18 YC4 10/9 8/7 6/5 4/3 2/1
6 7 5 3 2 1 9 10 11 12
WE WE WE WE WE WE WE WE WE WE WE
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
C
PDPCB APCPCB
ODSW
3 2 1
4 5 6
GY GY GY
3 2 1
3 2 1 YC1 YC4
SHPSW
YC2
D
LSU WE WE WE PM 1 2 3 4 5 3R CL 1G 5 4 3 2 1 WE WE WE WE WE RD BK GN 1 2 3 4 5 1 2 3 CFM1 1 2
YC3
5 4 3 2 1
GY GY GY GY GY
1 2 3 4 5
7 6 5 4 3
1 2 3 4 5
5 4 3 2 1
RM
YC15 +5V2 4 SEPSWN 3 EXTSWN 2 GND 1 GY GY GY GY 9 10 11 12 FAN1DRN +24V1 THERMA+5V THERMA YC14
BK BK BK BK
1 2 3 4
ESW FSSW
E
1 2 2 1 OFS B W R BK WE RDWE
1 2 3
3 2 1
GY GY GY
4 3 2 1
EM
Service Manual
F
FCSSW OE FTH FH-S WE WE FH-M BK FTS 3 2 1 WE WE BK OE YC5 1 2 3 +5V1 NC +5V3 YC6 3 SH.OUT 2 1 MH.OUT PSPCB H.LIVE
DM
GY GY GY GY GY GY GY
1 2 3 4 5 6 7
+24V +24V1 +24V1 PGND PGND COUNTN MHEATN SHEATN SLEPN ZCROSSC SGND +24V2 SGND +5V3
14 13 12 11 10 9 8 7 6 5 4 3 2 1 YC1
GY GY GY GY GY GY GY GY GY GY GY GY GY GY
1 2 3 4 5 6 7 8 9 10 11 12 13 14
+24V +24V1 +24V1 PGND PGND COUNTN MHEATN SHEATN SLEPN ZCROSSC SGND +24V2 SGND +5V3
CFM2
G
AC IN
YC9
YC1
MSW
OR BE BE RD RD LIVE FGND COM +5V SGND PGND +24V4 +24V2 NC +24V1 7 6 5 4 3 2 1 RD LCSSW
+24V4/RCLTN 16/15 +24V4/THVADJ 14/13 +24V4/THVDRN 12/11 PGND/MHVADJC 10/9 PGND/SHVDRN 8/7 PGND/MHVDRN 6/5 PGND/SHVISELN 4/3 +5V/HVCLKC 2/1 YC22 YC8
1 2 3 4
BK BK BK BK
4 3 2 1
PLSW
ZENER PCB
H I J 8 7
11 10 9 8 7 6 5 4 3 2 1
+5V2 SGND +5V2 SGND LOPSDO LOPSDI LOPSCLK LOPSEL0 LOPSEL1 LOPSEL2 LOPSRDY
TCONDET 5 SGND 6
BK BK
2 1
TCDSW
YC5
NC NC NC +5V2 IPPSWN SGND +24V4 ICLTN LOWER PAPER FEEDER (OPTION) DPCB LOWER PAPER FEEDER (OPTION)
1 2 3 4 5 6 7 8
13 12 11 10 9 8 7 6
GY GY GY GY GY
1 2 3 4 5
5 4 3 2 1
1 2
1 2
5 4
GY GY
1 2
2 1
BYPPWSW
+5V2 11 REGSWN 12 SGND 13 1 2 3 1 2 3 WE WE WE 3 2 1 YC2 3 +5V2 2 C1PDSWN 1 SGND YC4 TCS B W R BK WE RDWE 1 2 3 3 2 1 SGND TONEPY +5V2
3 2 1
GY GY GY
1 2 3
1 2 3
RSW
PFCL
BYPPFSOL
2-4-12
UPDATING STATUS
DATE
PAGES UPDATED
PAGES
CODE
03/2004
1st EDITION
221
Y102911-6