Professional Documents
Culture Documents
741GX-M (1.0a)
741GX-M (1.0a)
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0a
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp. MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation. Other product names used in this manual are the properties of their respective owners and are acknowledged.
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system's manufacturer could void the user's authority to operate the equipment.
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
ii
TABLE OF CONTENTS
Preface Features Translations i v
CHAPTER 1
Introducing the Motherboard
1
1
Introduction.................................................................................................1 Features .....................................................................................................2 Choosing a Computer Case .......................................................................4 Motherboard Components ..........................................................................5
CHAPTER 2
Installing the Motherboard
7
7
Safety Precautions......................................................................................7 Quick Guide ................................................................................................7 Installing the Motherboard in a Case ..........................................................8 Checking Jumper Settings..........................................................................8 Setting Jumpers ............................................................................................... 8 Checking Jumper Settings ............................................................................... 9 Jumper Settings ............................................................................................... 9 Connecting Case Components .................................................................10 Front Panel Connector ....................................................................................12 Installing Hardware ...................................................................................13 Installing the Processor...................................................................................13 Installing Memory Modules ...........................................................................16 Installing a Hard Disk Drive/CD-ROM..........................................................17 Installing a Floppy Diskette Drive..................................................................18 Installing Add-on Cards..................................................................................19 Connecting Optional Devices .........................................................................21 Connecting I/O Devices ............................................................................23
CHAPTER 3
Using BIOS
24
24
About the Setup Utility ..............................................................................24 The Standard Configuration ...........................................................................24 Starting Setup .................................................................................................25 Updating the BIOS .........................................................................................26 Using BIOS ...............................................................................................27 Standard CMOS Features ...............................................................................27 Advanced BIOS Features ...............................................................................29 Advanced Chipset Setup.................................................................................32 Integrated Peripherals.....................................................................................34 Power Management Setup ..............................................................................38 iii
PNP/PCI Configurations.................................................................................41 PC Health Status.............................................................................................42 Frequency/Voltage Control.............................................................................43 Load Fail-Safe Defaults Option......................................................................44 Load Optimized Defaults Option....................................................................44 Set Supervisor/User Password........................................................................44 Save & Exit Setup Option ..............................................................................45 Exit Without Saving .......................................................................................45
CHAPTER 4
Using the Motherboard Software
46
46
About the Software CD-ROM ...................................................................46 Auto-installing under Windows 98/ME/2000/XP .......................................46 Running Setup ................................................................................................47 Manual Installation....................................................................................49 Utility Software Reference ........................................................................49
iv
Features Translations
Caractristiques
Processeur La carte mre utilise un Socket A de 462 broches AMD qui prend en charge un Bus Frontal (FSB) de 333/266/200 MHz, prenant en charge les CPU AMD Athlon XP/Sempron/Athlon /Duron avec FSB jusqu' 333 MHz. Le chipset sur cette carte mre comprend le chipset SiS741GX Northbridge combin avec le chipset SiS964L Southbridge. Le tableau ci-dessous explique brivement certaines des caractristiques avances du chipset. Chipset SiS741GX NB Caractristiques Supporte les CPU AMD Athlon XP/ Sempron/ Athlon / Duron CPU avec FSB jusqu 333MHz Supporte les DDR 333/266 SDRAM Compatible avec AGP 3.0 Universel (supporte la carte 1.5V AGP seulement) Supporte linterface AGP 8X/4X avec w/Fast Write Transaction Intgre un moteur 3D de haute qualit Supporte les registres de configuration de gestion dalimentation PCI pour prendre en charge le contrleur de coupure dalimentation ACPI Conforme aux spcifications PCI 2.3 Prend en charge les rseaux domestiques full duplex 10base-T, 100base-Tx, 1Mb/s & 10 Mb/s Conforme AC 97 v2.3 supportant 6 Chanaux de sortie haut-parleur AC 97 et Modem V.90 HSP Gestion d'Alimentation avance. (Exigences ACPI 2.0 et exigences APM 1.2)
Chipset
SiS964L SB
Les caractristiques cl supplmentaires incluent le support pour huit ports USB, contrleur Fast Ethernet MAC, interface AC 97, gestion dalimentation avance, contrleur DMA et contrleur de clavier intgrs. Mmoire Peut recevoir deux logements sans mmoire tampon en 2.5V de 184 broches Support de module mmoire DDR SDRAM jusqu 333/266 MHz Chaque logement supporte jusqu 1 Go avec une capacit maximum totale de 2 Go Cette carte mre inclut un logement AGP qui offre huit fois la bande passante des spcifications AGP dorigine. LAGP 3.0 (8X AGP) offre une amlioration significative de performances accompagne damliorations de fonctionnalits sur lAGP2.0. Cette interface reprsente lvolution naturelle de lAGP exis-
Graphiques
tante pour rpondre une demande toujours croissante dinterfaces graphiques en environnements de station de travail et de bureau. Audio Le codec Audio AC' 97 est conforme aux spcifications AC' 97 2.3 rpondant aux exigences PC2001 et supportant Sortie S/PDIF. Il possde aussi une mmoire tampon intgre et PLL interne. Les fonctionnalits comprennent le support du commutateur analogique pour sortie arrire (partage), la prise de ligne dentre (partage), centre basse (partage), et prise MIC la sortie audio 6 canaux. La carte mre est livre avec les options dextensions suivantes: Trois logements PCI 32 bits Un slot conforme AGP 3.0 avec vitesse 8X/4X (supporte la carte 1.5V AGP seulement) Un logement Communications Network Riser (CNR) (Interface AC 97 seulement) Deux connecteurs IDE supportant quatre lecteurs IDE Une interface de lecteur de disquette pouvant supporter 2 lecteurs de disquettes Cette carte mre supporte la matrise de bus Ultra DMA avec des vitesses de transfert de 33/66/100/133 Mo/sec. Le LAN Interne est un Fast Ethernet Phyceiver avec interface MII sur puce MAC. Il offre les fonctionnalits suivantes: Supporte linterface MII Supporte le fonctionnement en 10/100Mbps Supporte le fonctionnement en half/full duplex Fonctionnement en 3.3V avec signal 5V Fonctionnement faible consommation dnergie La carte mre possde un jeu complet de ports dE/S et de connecteurs: Deux ports PS/2 pour souris et clavier Un port srie (COM1) Un port VGA Un port parallle Quatre ports USB Un port LAN (optionnel) Prises audio pour microphone, ligne dentre et ligne de sortie Cette carte mre utilise Award BIOS qui permet aux utilisateurs de configurer de nombreuses fonctionnalits du systme comprenant les suivantes : Gestion dalimentation Alarmes de rveil Paramtres de CPU Synchronisation de CPU et de mmoire Le microprogramme peut aussi tre utilis pour dfinir les paramtres pour les vitesses dhorloges de diffrents processeurs.
Options dExtensions
E/S Intgres
Microprogramme BIOS
Certaines spcifications matrielles et lments de logiciels peuvent tre modifis sans avertissement.
vi
Funktionen
Prozessor Das Motherboard ist mit einem AMD 462-Pin Sockel ausgestattet, dass 333/266/200 MHz Front Side Bus (FSB) und AMD Athlon XP/Sempron/Athlon/Duron CPU mit FSB bis zu 333 MHz untersttzt. Der Chipsatz dieses Motherboards verfgt ber die SiS741GX Northbridge, die mit der SiS964L Southbridge verbunden ist In der untenstehenden Tabelle werden einige der fortschrittlichen Funktionen des Chipsatzes kurz vorgestellt: Chipsatz SiS741GX NB Funktionen Untersttzt AMD Athlon XP/ Sempron /Athlon / Duron CPU mit FSB bis zu 333MHz Untersttzt DDR 333/266 SDRAM Entspricht Universal AGP v3.0 (untersttzt nur 1.5V AGP Interface) Untersttzt AGP 8X/4X-Interface mit Fast Write-Abwicklung Hochwertiger 3D-Engine integriert Untersttzung PCI-Power-ManagementKonfigurationsregister zur Untersttzung eines ACPI Power Down-Controllers Kompatibel mit der PCI 2.3-Spezifikation Untersttzung fr Vollduplex 10base-T, 100base-Tx, 1Mb/Sek. & 10 Mb/Sek. HomeNetworking Kompatibel mit AC 97 v2.3; Untersttzung fr sechst Kanle fr AC 97Lautsprecherausgnge sowie fr ein V.90 HSP-Modem Advanced Power Management (ACPI 2.0Anforderungen und APM 1.2-Anforderungen)
Chipsatz
SiS964L SB
Zustzliche Schlsseleigenschaften umfassen die Untersttzung fr acht USB-Anschlsse, Fast Ethernet MAC Controller, AC 97Interface, Advanced Power Management, integrierter DMA Controller und Tastatur Controller. Speicher Nimmt zwei ungepufferte 2.5V 184-Pin Steckpltze auf Untersttzt DDR bis zu 333/266 MHz SDRAMSpeichermodul Jeder Steckplatz untersttzt bis zu 1 GB mit einer maximalen Gesamtkapazitt von bis zu 2 GB Das Motherboard enthlt einen AGP-Steckplatz mit der achtfachen Bandbreite der ursprnglichen AGP-Spezifikation. AGP 3.0 (8XAGP) bietet gegenber AGP2.0 eine erhebliche Leistungssteigerung und verbesserte Features. Dieses Interface stellt die natrliche Weiterentwicklung des bestehenden AGP dar, um den stetig anwachsenden Anforderungen an die Grafikschnittstellen innerhalb der Workstations und DesktopUmgebungen gerecht zu werden. Der AC 97 Audio-Codec entspricht der AC 97 2.3Spezifikation welche die PC2001-Anforderungen erfllt und
Grafik
Audio
vii
S/PDIF Ausgang untersttzt. Er verfgt ber einen eingebauten Puffer und internes PLL. Weitere Eigenschaften umfassen einen Analog-Schalter fr den Hinterausgang (geteilt), Line-In Anschluss (geteilt), Center/Bass (geteilt) und einen Mikrophonstecker fr 6 Kanal Audioausgabe. Expansion Options Das Mainboard bietet die folgenden Erweiterungsoptionen: Drei 32-bit PCI-Steckpltze Eine nach AGP 3.0-geme Schlitzeinrichtung mit einer Geschwindigkeit von 8X/4X (untersttzt nur 1.5V AGP Interface) Einen Steckplatz fr Communications Network Riser (CNR) (nur AC 97-Interface) Zwei IDE-Stecker, die vier IDE- Vorrichtungen Eine Diskettenlaufwerk-Schnittstelle welche 2 FDDVorrichtungen untersttzen kann Dieses Motherboard untersttzt Ultra DMA Bus-Mastering mit bertragungsraten von 33/66/100/133 MB/s. Der Integriertes LAN ist ein Fast Ethernet Phyceiver mit einem MII-Interface und einem MAC-Chip. Er hat folgende Funktionen: Untersttzung fr MII-Interface Untersttzung fr 10/100 Mbps/Sek.-Betrieb Untersttzung fr Halb-/Vollduplexbetrieb 3.3 Volt-Betrieb mit 5 Volt-Signalen Geringer Stromverbrauch beim Betrieb Das Mainboard verfgt ber einen kompletten Satz von I/OSchnittstellen und Anschlssen: Zwei PS/2-Schnittstellen fr Maus und Tastatur Eine serielle Schnittstelle (COM1) Eine VGA Schnittstelle Eine parallele Schnittstelle Vier USB-Schnittstellen Eine LAN-Schnittstelle (optional) Audiobuchsen fr Mikrofon, Line-in und Line-out Dieses Mainboard setzt das Award BIOS ein, mit dem der Anwender viele Systemeigenschaften selbst konfigurieren kann, einschlielich der folgenden: Energieverwaltung Wake-up-Alarm CPU-Parameter CPU und Speichertiming Mit der Firmware knnen auch die Parameter fr verschiedene Prozessortaktgeschwindigkeiten eingestellt werden.
Integrierte I/O
BIOS-Firmware
Bestimmte Hardwarespezifikationen und Teile der Softwareausstattung knnen ohne weitere Ankndigung abgendert werden.
viii
Caratteristiche
Processore La scheda madre utilizza una presa A a 462 pin AMD che supporta un Front Side Bus (FSB) da 333/266/200 MHz, compatibile con CPU AMD Athlon XP/Sempron/Athlon/Duron con FSB fino a 333 MHz. Il chipset composto dai chipset Northbrigde SiS741GX e Southbridge SiS964L. La tabella sottostante presenta una panoramica delle funzioni avanzate del chipset: Chipset SiS741GX NB Caratteristiche Vengono supportate le CPU AMD Athlon XP/Sempron/Athlon / Duron con FSB fino a 333MHz Supporta DDR 333/266 SDRAM Compliant with Universal AGP 3.0 (supporta solo l'interfaccia 1.5V AGP) Supporta l'interfaccia AGP 8X/4X con Funzione Transizione Fast Write Motore 3D integrato di altissima qualit Supporto per la gestione Risparmio Energia PCI garantendo la compatibilit con i controller ACPI Conforme allo standard PCI 2.3 Supporto home networking full duplex per 10base-T, 100base-Tx, 1Mb/s & 10 Mb/s Conforme allo standard AC 97 v2.3 garantendo il supporto a 6 Canali dele uscite speaker AC 97 e modem HSP-Modem V.90 Gestione avanzata per il risparmio energetico. (requisiti ACPI 2.0 e APM 1.2)
Chipset
SiS964L SB
Altre caratteristiche fondamentali sono: supporto per otto porte USB, controller Fast Ethernet MAC, interfaccia AC 97, Gestione avanzata per il risparmio energetico , controller DMA controller integrato e controller tastiera. Memoria Presenta due slot a 184 pin 2.5 V unbuffered Supporta un modulo di memoria SDRAM con DDR fino a 333/266 Mhz Ciascun slot supporta fino a 1 GB per una capacit totale massima di 2 GB La scheda madre include uno slot AGP che fornisce otto volte la larghezza di banda delle specifiche AGP originarie. Lo standard AGP 3.0 (8XAGP) garantisce prestazioni significativamente superiori oltre ad altri miglioramenti rispetto allo standard AGP2.0. Questa interfaccia rappresenta la naturale evoluzione dell'AGP esistente ed in grado di soddisfare le sempre maggiori aspettative del mercato nel campo delle interfacce grafiche, sia in ambiente workstation che in ambiente desktop. Il codec Audio AC97 conforme alla specifica AC 97 2.3 che soddisfa i requisiti PC2001 e supporta Uscita S/PDFI. Inoltre ha una memoria tampone interna e PLL interno. Le
Grafica
Audio
ix
caratteristiche includono supporto per interruttore analogico sulluscita posteriore (condivisa), il jack di ingresso linea (condiviso), centrale/bassi (condivisi), e jack MIC per fornire unuscita a 6 canali audio. Opzioni di espansione La scheda madre presenta le seguenti opzioni di espansione: Tre slot PCI 32 bit Uno slot compatibile con lo standard AGP 3.0 8X/4X (supporta solo l'interfaccia 1.5V AGP) Una slot Communications e Network Riser (CNR) (solo interfaccia AC 97) Due connettori IDE che supportano quattro grado IDE Uninterfaccia per la gestione dei drive in grado si supportare 2 FDD La scheda madre supporta il bus mastering Ultra DMA con transfer rate 33/66/100/133 MB/sec. La scheda LAN integrato una periferica Fast Ethernet dotata di interfaccia MII per chip MAC. dotata delle seguenti caratteristiche: Dotata di interfaccia MII Supporto 100/10 Mbps Supporto Half e Full Duplex Funzionamento a 3.3V con segnale a 5V Basso consumo energetico La scheda madre dotata da una serie completa di porte e connettori I/O: Due porte PS/2 per tastiera e mouse Una porta seriale (COM1) Una porta VGA Una porta parallela Quattro porte USB Una porta LAN (opzionale) Jack audio per microfono, ingresso linea e uscita linea Questa scheda madre adotta un BIOS Award che permette agli utenti di configurare le caratteristiche principali del sistema, inclusi: Gestione energia Allarmi wake up Parametri CPU Temporizzazione CPU e memoria Il firmware pu anche essere usato per impostare i parametri per diverse velocit di clock.
Inizializza I/O
Firmware BIOS
Alcune specifiche hardware ed elementi software sono soggetti a variazioni senza preavviso.
Caractersticas
Procesador La placa principal usa un AMD 462-pin Receptculo A que soporta el Bus de Lado Frontal (Front Side Bus/FSB) de 333/266/200 MHz, soporta una CPU AMD Athlon XP/Sempron /Athlon/Duron con FSB hasta 333 MHz. El chipset en esta placa principal incluye la SiS741GX Northbridge combinado con el chipset SiS964L Southbridge. La tabla abajo explica algunas de las caractersticas avanzadas del chipset: Chipset SiS741GX NB Caractersticas Soporta las CPUs AMD Athlon XP/Sempron/ Athlon / Duron con FSB hasta 333MHz Soporta DDR 333/266 SDRAM Conforme con Universal AGP 3.0 (soporta interfaz 1.5V AGP solamente) Soporta la interfaz AGP 8X/4X c/ Transaccin de Escritura Rpida Procesador 3D de alta calidad incorporado Soporta los registros de configuracin de administracin de suministro PCI para soportar el controlador de apagado ACPI Conforme con la especificacin PCI 2.3. Soporta la red de trabajo residencial de duplex completo 10base-T, 100base-Tx, 1Mb/s & 10 Mb/s. Conforme con AC 97 v2.3 que soporta 6 Canales de salidas de altoparlante AC 97 y V.90 HSP-Mdem Administracin de Suministro Avanzada. (Requisitos de ACPI 2.0 y de APM 1.2)
Chipset
SiS964L SB
Caractersticas claves adicionales incluyen soporte para ocho puertos USB, controlador Fast Ethernet MAC, Interfaz AC 97, Administracin de Suministro Avanzada, controlador DMA integrado y controlador de teclado. Memoria Acomoda dos ranuras 2.5V 184-pin sin buffer Soporta DDR hasta mdulo de memoria 333/266 MHz SDRAM Cada ranura soporta hasta 1 GB con una capacidad mxima total de 2 GB Esta placa principal incluye una ranura AGP que provee ocho veces la ancha de banda de la especificacin de AGP original. El AGP 3.0 (8XAGP) ofrece un aumento significativo en rendimiento junto con mejoramientos de caracterstica para AGP2.0. Esta interfaz representa la evolucin natural del AGP existente para satisfacer las crecientes demandas enfocadas en las interfaces de grficas dentro de los ambientes de estacin de trabajo y sobremesas. El codec de sonido AC 97 es conforme con la especificacin AC 97 2.3, que satisface los requisitos de PC2001 y soporta S/PDIF Out. Tambin tiene un buffer incorporado y PLL
Grficas
Audio
xi
interno. Las caractersticas incluyen soprte para el interruptor analgico para salida trasera (compartir), la clavija de entrada de lnea (compartir), centro/bajo (compartir), y clavija MIC para exportar sonido de 6 canales. Opciones de Expansin La placa principla viene con las sigtes. opciones de expansin: Tres ranuras 32-bit PCI Una ranura con conformidad de AGP 3.0 con las velocidades 8X/4X (soporta interfaz 1.5V AGP solamente) Una ranura de Communications Network Riser (CNR) (Intrefaz AC 97 solamente) Dos conectores IDE que soportan cuatro dispositivos IDE Una interfaz de unidad de disco floppy que soporta 2 dispositivos FDD Esta placa principal soporta mastering de bus Ultra DMA con ndices de transferencia de 33/66/100/133 MB/seg. El LAN Abordo es un Fast Ethernet Phyceiver con interfaz MII para el chip MAC. Provee las sigtes. caractersticas: Soporta Interfaz MII Soporta operacin 10/100Mbps Soporta operacin medio/full duplex Operacin 3.3V con seal 5V Bajo consumo de operacin La placa principal tiene un juego completo de puertos y conectores I/O: Dos puertos PS/2 para ratn y teclado Un puerto serial (COM1) Un puerto VGA Un puerto paralelo Cuatro puertos USB Un puerto LAN (optativo) Clavijas de sonido para micrfono, entrada y salida de lnea Esta placa principal usa AwardI BIOS que habilita los usuarios a configurar muchas caractersticas de sistema que incluyen las sigtes.: Administracin de energa Alarmas despertadoras Parmetros de CPU Sincronizacin de CPU y de Memoria El firmware tambin se puede usar para configurar parmetros para diferentes velocidades de reloj.
I/O Integrado
Firmware de BIOS
Algunas especificaciones de hardware e tems de software son sujetos a cambio sin previo aviso.
xii
333/266/200 MHz(FSB)AMD 462Socket A 333 MHz FSBAMD Athlon XP/Sempron/Athlon/Duron CPU SiS741GX Northbridge SiS964L Southbridge SiS741GX NB 333 MHz FSBAMD Athlon XP/Sempron /Athlon/Duron CPU DDR 333/266 SDRAM AGP 3.0(1.5V AGP ) AGP 8X/4X 3D PCIACPI SiS964L SB PCI 2.3 10base-T100base-Tx 1Mb/ & 10 Mb/ AC 97 v2.3 6 AC 97 V.90 HSP- APM (ACPI 2.0 APM 1.2 ) 8USBMAC AC 97 DMA 22.5V184 DDR 333/266 MHz SDRAMDDR 1 GB2 GB
xiii
AC 97 AC 97 2.3 PC2001S/PDIF Out PLL () ()/ ()6 MIC : 332PCI 1AGP (1.5V AGP) (CNR) (AC 97) 2IDE 4 IDE 12 FDD
33/66/100/133 MB/Ultra DMA LAN () LAN Fast Ethernet Phyceiver MACMII MII 10/100Mbps / 5V3.3V
BIOS
xiv
333/266/200 MHz Front Side Bus (FSB) AMD 462 A , AMD XP/// CPU FSB 333 MHz . SiS741GX Northbridge SiS964L Southbridge . . SiS741GX NB FSB 333MHz AMD XP/// CPU DDR 333/266 SDRAM Universal AGP 3.0 (1.5V AGP ) AGP 8X/4X w/ Fast Write Transaction 3D ACPI PCI SiS964L SB PCI 2.3 10base-T,100base-Tx, 1Mb/s 10Mb/s 6 AC 97 V.90 HSP AC 97 v2.3 (ACPI 2.0 APM 1.2 ) 8 USB , MAC , AC 97 , , DMA . 2 unbuffered 2.5V 184 DDR 333/266 MHz SDRAM 1 GB . 2 GB
AGP 8 AGP . AGP 3.0 (8XAGP) AGP2.0 . AGP . AC 97 AC 97 2.2 PC2001 S/PDIF Out . PLL , - (), (), / (), 6 MIC . : 32 PCI 3
xv
8X/4X AGP 3.0 1 (1.5V AGP ) Communications Network Riser (CNR) 1 (AC 97 ) 4 2 IDE 2 FDD 1
33/66/100/133 MB/sec Ultra DMA bus mastering . LAN ( ) LAN MAC MII Phyceiver : I/O BIOS MII 10/100Mbps half/full 5V 3.3V PS/2 2 1 (COM1) VGA 1 1 USB 4 LAN 1 ( ) ,
I/O :
xvi
333/266/200 MHz AMD 462Socket A333MHzFSBAMD Athlon XP/Sempron/Athlon/Duron CPU SiS741GXSiS964L . SiS741GX NB AMD Athlon XP/Sempron/ Athlon/ Duron CPU FSB333MHz DDR 333/266 SDRAM AGP 3.0(1.5) AGP 8X/4X 3D PCIACPI SiS964L SB PCI 2.3 10base-T100base-Tx 1Mb/ & 10 Mb/(home networking) AC 97 v2.3 6AC 97 V.90 HSP- (ACPI 2.0 APM 1.2 ) 8USB,MAC , AC 97,DMA 22.5v 184 DDR 333/266 MHz SDRAM 1GB2GB
AGPAGP8 AGP 3.0 (8XAGP) AGP2.0 AGP AC 97/AC 97 2.3 PC2001S/PDIF / PLL ()()center/bass() 6 : 332PCI 1 AGP 3.0 8X/4X (1.5 ) 1(Communications Network Riser, CNR) (AC 97) 2IDE4IDE
xvii
1 2 FDD
Ultra DMA 33/66/100/ 133 MB/sec LAN () LAN Phyceiver MAC MII : BIOS MII 10/100Mbps / 3.3V5V 2 PS/2 1(COM1) 1VGA 1 4USB 1LAN()
BIOS
xviii
AMD 462-pin Socket A 333/266/200 MHz (FSB) FSB 333 MHz AMD Athlon XP/ Sempron/Athlon/Duron CPU SiS741GX SiS964L SiS741GX NB FSB 333MHz AMD Athlon XP/Sempron/Athlon / Duron CPU DDR 333/266 SDRAM AGP 3.0 1.5V AGP AGP 8X/4X 3D PCI ACPI SiS964L SB PCI 2.3 10base-T100base-Tx1Mb/s & 10 Mb/s AC 97 v2.3 AC 97 6 V.90 HSP-Modem ACPI 2.0 APM 1.2 8- USB MAC AC 97 DMA 2 2.5V 184 pin 333/266 MHz DDR SDRAM 1 GB 2 GB
AGP AGP 8 AGP 3.0 (8xAGP) AGP2.0 AGP AC' 97 Audio AC 97 2.3 PC2001 S/PDIF Out PLL / 6 MIC 3 32 PCI 1 8X/4X AGP 3.0 1.5V AGP 1 (CNR) AC 97 2 IDE 4 IDE 1 2
xix
133 MB/sec Onboard LAN Onboard LAN Phyceiver MAC MII I/O BIOS MII 10/100Mbps / 3.3V 5V 2 PS/2 1 (COM1) 1 VGA 1 4 USB 1 LAN CPU CPU
I/O
Award BIOS
xx
Chapter 1
Introduction
Thank you for choosing 741GX-M motherboard. This motherboard is designed to fit the advanced AMD processors in the 462-pin package. This motherboard is based on micro-ATX form factor featuring the SiS741GX Northbridge and SiS964L Southbridge chipsets. It accommodates AMD Athlon XP / Sempron / Athlon / Duron Processors supporting Front Side Bus (FSB) up to 333 / 266 / 200 MHz. In addition, the motherboard has 2 built-in 184-pin DIMM slots, and the main memory is expandable to a maximum of 2GB. The SiS741GX Northbridge chipset features an AGP 8X bridge and a DDR333 Memory controller, supporting AMD Athlon XP / Sempron / Athlon / Duron processors with FSB up to 333MHz. While the SiS964L Southbridge chipset provides eight USB 2.0 ports, 6-channels audio speaker compliant with AC 97 v2.3 specification, IDE channels PIO mode 0, 1, 2, 3, 4 and Ultra DMA 133/100/66/33. This high performance motherboard is intended to give customers a high quality, multimedia solution and state-of-the-art technology. It provides a complete set of I/O ports, such as dual channel IDE interfaces, a floppy controller, a serial port, a VGA port, an EPP/ECP capable bi-directional parallel port connector, four USB (Universal Serial Bus) connectors, LAN port, a PS/2 keyboard and mouse connector, and audio jacks for microphone, line-in, lineout. One AGP slot (support 1.5V AGP interface only), three PCI local bus slots and one CNR (Communication and Networking Riser) slot providing expandability for add-on peripheral cards.
Features
Processor The motherboard uses an AMD 462-pin Socket A that supports 333/266/200 MHz Front Side Bus (FSB), supporting AMD Athlon XP/Sempron/Athlon/Duron CPU with FSB up to 333 MHz. The chipset on this motherboard includes the SiS741GX Northbridge combine with SiS964L Southbridge chipset. The table below briefly explains some of the chipsets advanced features. Chipset SiS741GX NB Features Supprots AMD Athlon XP/Sempron/Athlon/ Duron CPU with FSB up to 333 MHz Supports DDR 333/266 DDR SDRAM Compliant with Universal AGP 3.0 (support 1.5V AGP interface only) Supports AGP 8X/4X Interface w/ Fast Write Transaction Built-in a high quality 3D engine Supports PCI power management configuration registers for supporting ACPI power down controller Compliant with PCI 2.3 specification Supports full duplex 10base-T, 100base-Tx, 1 Mb/s & 10 Mb/s Home Networking Compliant with AC 97 v2.3 supporting 6 Channels of AC 97 speaker outputs and V.90 HSP-Modem Advanced Power Management (ACPI 2.0 requirements and APM 1.2 requirements)
Chipset
SiS964L SB
Additional key features include support for eight USB ports, Fast Ethernet MAC controller, AC 97 interface, advanced power management, integrated DMA controller and keyboard controller. Memory Accommodates two unbuffered 2.5V 184-pin slots Supports DDR up to 333/266 MHz SDRAM memory module Each slot supports up to 1 GB with a total maximum capacity of 2 GB This motherboard includes an AGP slot that provides eight times the bandwidth of the original AGP specification. The AGP 3.0 (8X AGP) offers a significant increase in performance along with feature enhancements to AGP2.0. This interface represents the natural evolution from the existing AGP to meet the ever-increasing demands placed on the graphic interfaces within the workstation and desktop environments.
Graphics
Audio
The AC 97 Audio codec is compliant with the AC 97 2.3 specification that meets the PC2001 requirements and supports S/PDIF Out. It also has a built-in buffer and internal PLL. Features include support for analog switch for rear-out (share), the line-in jack (share), center/bass (share), and MIC jack to output 6 channels audio. The motherboard comes with the following expansion options: Three 32-bit PCI slots One AGP 3.0 compliant slot with 8X/4X speed (supports 1.5V AGP Interface only) A Communications Network Riser (CNR) slot (AC 97 interface only) Two IDE connectors which support four IDE devices One floppy disk drive interface which can support 2 FDD devices This motherboard supports Ultra DMA bus mastering with transfer rates of 33/66/100/133 MB/sec. The onboard LAN is a Fast Ethernet Phyceiver with MII interface to MAC chip. It provides the following features: Support MII interface Support 10/100Mbps operation Support half/full duplex operation 3.3V operation with 5V signal Low operation power consumption The motherboard has a full set of I/O ports and connectors: Two PS/2 ports for mouse and keyboard One serial port (COM1) One VGA port One parallel port Four USB ports One LAN port (optional) Audio jacks for microphone, line-in and line-out This motherboard uses Award BIOS that enables users to configure many system features including the following: Power management Wake-up alarms CPU parameters CPU and memory timing The firmware can also be used to set parameters for different processor clock speeds.
Expansion Options
Integrated I/O
BIOS Firmware
Some hardware specifications and software items are subject to change without prior notice.
Motherboard Components
This concludes Chapter 1. The next chapter explains how to install the motherboard.
Chapter 2
Safety Precautions
Follow these safety precautions when installing the motherboard: Wear a grounding strap attached to a grounded device to avoid damage from static electricity. Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard. Leave components in the static-proof bags they came in. Hold all circuit boards by the edges. Do not bend circuit boards.
Quick Guide
This Quick Guide suggests the steps you can take to assemble your system with the motherboards. The following table provides a reference for installing specific components:
Locating Motherboard Components Installing the Motherboard in a Case Setting Jumpers Installing Case Components Installing the CPU Installing Memory Installing a HDD and CD-ROM Drive Installing an FDD Installing Add-on Cards Connecting Options Connecting Peripheral (I/O) Devices Go to page 5 Go to page 8 Go to page 8 Go to page 10 Go to page 13 Go to page 16 Go to page 17 Go to page 18 Go to page 19 Go to page 21 Go to page 23
Most system cases have mounting brackets installed in the case, which correspond to the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.
Ensure that your case has an I/O template that supports the I/O ports and expansion slots on your motherboard.
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.
The illustrations below show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is OPEN. This illustration shows a 3-pin jumper. Pins 1 and 2 are SHORT.
Short
Open
1 2 3
Jumper Settings
Jumper JP1 Type 3-pin Description Clear CMOS 1-2: Normal 2-3: Clear CMOS Before clearing CMOS, make sure to turn off the system.
JP3 3-pin BIOS Protect 1-2: Disable 2-3: Enable
Setting (default)
JP1
JP3
2.
3.
4.
5. 6.
10
S0 Light
S1 Blinking
S3 Blinking
S4/S5 Dark
11
Pin 1 3 5 7 9
Signal
HD_LED_P HD_LED_N RST_SW_N RST_SW_P RSVD
Function
Hard disk LED (positive) Hard disk active LED (negative) Reset Switch Reset Switch Reserved
Pin 2 4 6 8 10
Signal
FP PWR/SLP FP PWR/SLP PWR_SW_P PWR_SW_N NC
Function
MSG LED [dual color or single color (+)] MSG LED [dual color or single color (-)] Power Switch Power Switch No pin
Hard Drive Activity LED Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector. Power / Sleep / Message Waiting LED Connecting pins 2 and 4 to a single- or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication. Reset Switch Supporting the reset function requires connecting pins 5 and 7 to a momentary-contact switch that is normally open. When the switch is closed, the board resets and runs POST. Power Switch Supporting the power on/off function requires connecting pins 6 and 8 to a momentary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal debounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal. 12
This motherboard has a Socket 462 processor socket. When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.
13
Step 1
Step 2
Step 3
Step 4
Orient the CPU so the odd corner matches the odd corner of the socket. With the lever in an upright position, gently place the CPU on the socket; make sure that all pins line up with the socket holes. When pins are aligned, the CPU should seat itself in the socket. Apply very light pressure to ensure the CPU is evenly seated. Push the lever down and ensure it latches firmly. Note: Remember to apply thermal grease on top of the CPU.
14
1.
2.
Secure the two retention clips on either side of the fan/heatsink unit onto the Socket 462 base.
3.
Connect the CPU Cooling Fan power cable connector to the CPUFAN connector.
15
Refer to the following to install the memory modules. 1. This motherboard supports unbuffered DDR SDRAM only.
2. 3.
Push the latches on each side of the DIMM slot down. Align the memory module with the slot. The DIMM slots are keyed with notches and the DIMMs are keyed with cutouts so that they can only be installed correctly.
4. 5.
Check that the cutouts on the DIMM module edge connector match the notches in the DIMM slot. Install the DIMM module into the slot and press it firmly down until it seats correctly. The slot latches are levered upwards and latch on to the edges of the DIMM.
6.
16
IDE2: Secondary IDE The second drive on this controller must be set to slave mode. The configuration is the same as IDE1.
You must orient the cable connector so that the pin 1 (color) edge of the cable corresponds to the pin 1 of the I/O port connector.
IDE devices have jumpers or switches that are used to set the IDE device as MASTER or SLAVE. Refer to the IDE device users manual. When installing two IDE devices on one cable, ensure that one device is set to MASTER and the other device is set to SLAVE. The documentation of your IDE device explains how to do this. 17
About UltraDMA
This motherboard supports UltraDMA 66/100/133. UDMA is a technology that accelerates the performance of devices in the IDE channel. To maximize performance, install IDE devices that support UDMA and use 80-pin IDE cables that support UDMA 66/100/133.
You must orient the cable connector so that the pin 1 (color) edge of the cable corresponds to the pin 1 of the I/O port connector.
18
AGP Slot
The AGP slot is used to install 3D graphics adapter that supports the 8X AGP card which is also backward compatible with 4X AGP card. The slot is keyed to support only the latest 1.5-volt AGP cards. PCI slots are used to install expansion cards that have the 32-bit PCI interface. This slot is used to insert CNR cards with Modem and Audio functionality.
Note: Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.
19
3.
Secure the metal bracket of the card to the system case with a screw.
Note: For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.
20
21
Note: Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hang-up.
22
PS/2 Mouse PS/2 Keyboard LPT1 Serial Port (COM1) VGA Port Audio Ports
Use the upper PS/2 port to connect a PS/2 pointing device. Use the lower PS/2 port to connect a PS/2 keyboard. Use LPT1 to connect printers or other parallel communications devices. Use the COM ports to connect serial devices such as mice or fax/modems. Connect your monitor to the VGA port. Use the three audio ports to connect audio devices. The first jack is for stereo line-in signal. The second jack is for stereo line-out signal. The third jack is for microphone. Connect an RJ-45 jack to the LAN port to connect your computer to the Network. Use the USB ports to connect USB devices.
23
Chapter 3
Using BIOS
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options. This chapter provides explanations for Setup Utility options.
24
Starting Setup
The BIOS is immediately activated when you first turn on the computer. The BIOS reads system configuration in CMOS RAM and begins the process of checking out the system and configuring it through the power-on self test (POST). When these preliminaries are finished, the BIOS seeks an operating system on one of the data storage devices (hard drive, floppy drive, etc.). The BIOS launches the operating system and hands control of system operations to it. During POST, you can start the Setup program in one on two ways: 1. 2. By pressing Del immediately after switching the system on, or By pressing Del or pressing Ctrl+Alt+Esc when the following message appears briefly at the bottom of the screen during POST: TO ENTER SETUP BEFORE BOOT PRESS DEL KEY
If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the RESET button on the system case. You may also restart by simultaneously pressing Ctrl+Alt+Del. If you do not press the keys at the correct time and the system does not boot, an error message appears and you are again asked to:
25
3. 4. 5.
6.
Error Message
7.
Type the filename of the new BIOS in the File Name to Program text box. Follow the onscreen directions to update the motherboard BIOS.
26
8.
When the installation is complete, remove the floppy diskette from the diskette drive and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten.
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>. Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information. Some options (marked with a triangle ) lead to submenus that enable you to change the values for the option. Use the cursor arrow keys to scroll through the items in the submenu. In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a triangle .
27
IDE HDD Auto-Detection Press <Enter> while this item is highlighted to prompt the Setup Utility to automatically detect and configure an IDE device on the IDE channel. Note: If you are setting up a new hard disk drive that supports LBA mode, more than one line will appear in the parameter box. Choose the line that lists LBA for an LBA drive. IDE Primary/Secondary Master/Slave (Auto) Leave this item at Auto to enable the system to automatically detect and configure IDE devices on the channel. If it fails to find a device, change the value to Manual and then manually configure the drive by entering the characteristics of the drive in the items described below. Refer to your drive's documentation or look on the drive casing if you need to obtain this information. If no device is installed, change the value to None. Note: Before attempting to configure a hard disk drive, ensure that you have the configuration information supplied by the manufacturer of your hard drive. Incorrect settings can result in your system not recognizing the installed hard disk. Access Mode This item defines ways that can be used to access IDE hard disks such as LBA (Large Block Addressing). Leave this value at Auto and the system will automatically decide the fastest way to access the hard disk drive. Press <Esc> to return to the Standard CMOS Setup screen. 28
Video (EGA/VGA)
This item defines the video mode of the system. This motherboard has a builtin VGA graphics system; you must leave this item at the default value.
31
AGP Aperture Size (128MB) This item defines the size of the aperture if you use an AGP graphics adapter. It refers to a section of the PCI memory address range used for graphics memory. We recommend that you leave this item at the default value. AGP Fast Write Support (Disabled) This item controls the AGP bus Fast Write capability. Fast Write allows the AGP device to act like a PCI device. This allows it to skip the main memory and directly access the data that improves the AGP read performance. 32
AGP Data Transfer Rate (Auto) You can select the AGP device data transfer rate capability. Press <Esc> to return to the Advanced Chipset Setup screen.
Dual Display Support (Disabled) This item allows you to enable the Dual Display support. VGA Share Memory Size (32 MB) This item allows you to select the shared memory size for VGA usage. Graphics Engin Clock (133 MHz) This item reports the Graphics Engine Clock setting information to VGA BIOS. We recommend that you leave this item at the default value. Press <Esc> to return to the Advanced Chipset Setup screen.
33
Integrated Peripherals
These options display items that define the operation of peripheral components on the system's input/output ports.
Internal PCI/IDE (Both) Use these items to enable or disable the internal PCI IDE channels that are integrated on the motherboard. IDE Primary/Secondary Master/Slave PIO (Auto) Each IDE channel supports a master device and a slave device. These four items let you assign which kind of PIO (Programmed Input/Output) is used by IDE devices. Choose Auto to let the system auto detect which PIO mode is best, or select a PIO mode from 0-4. 34
Primary/Secondary Master/Slave UltraDMA (Auto) This option allows you to enable or disable UltraDMA support (if available) for the two IDE devices (Master and Slave drives) attached to that particular IDE channel. Normally, you should leave it as Auto and let the BIOS auto-detect if the drive supports UltraDMA. If it does, the proper UltraDMA transfer mode will be enabled for that drive, allowing it to burst data at up to 100MB/s. You should only disable it for troubleshooting purposes. Note: Setting this to Auto does not enable the UltraDMA or any of the slower DMA mode for IDE devices that do not support UltraDMA. Also, in order for any of those DMA modes to work (including UltraDMA modes), you will have to enable DMA transfer via the OS. IDE DMA Transfer Access (Enabled) This item allows you to enabled the transfer access of the IDE DMA. IDE Burst Mode (Enabled) This option, when enabled will instruct the system to send every write transaction to the write buffer. Burstable transactions then burst onto the PCI bus and nonburstable transactions do not. Press <Esc> to return to the Integrated Peripherals screen.
SIS USB Controller (Enabled) This item enables the USB controller. Leave this at the default Enabled if you want to connect USB devices to your computer. USB Ports Number (6 Ports) This item enables you to determine the number of USB ports. USB 2.0 Support (Enabled) Enable this item if your system supports USB 2.0 35
USB Legacy Support (Enabled) Use this item to enable or disable support for legacy USB devices. Setting to Auto allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. USB Mouse Support (Disabled) Enable this item if you plan to use a mouse connected through the USB port in a legacy operating system (such as DOS) that does not support Plug and Play. SIS AC 97 AUDIO (Enabled) This option allows you to control the onboard AC 97 audio. Disable this item if you are going to install a PCI audio add-on card. SIS S/W Modem (Enabled) This option allows you to control the onboard S/W modem. Disable this item if you are going to install an external modem. Onboard LAN Device (Enabled) This option allows you to control the onboard LAN device. Onboard LAN Boot ROM (Disabled) Use this item to enable and disable the booting from the onboard LAN or a network add-in card with a remote boot ROM installed. Press <Esc> to return to the Integrated Peripherals screen.
Onboard FDC Controller (Enabled) Select Enabled if your system has a floppy disk controller (FDB) installed on the system board and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field.
36
Onboard Serial Port 1 (3F8/IRQ4) This option is used to assign the I/O address and interrupt request (IRQ) for onboard serial port 1 (COM1). Onboard Parallel Port (378/IRQ7) This option is used to assign the I/O address and interrupt request (IRQ) for the onboard parallel port. Parallel Port Mode (ECP) Enables you to set the data transfer protocol for your parallel port. There are four options: SPP (Standard Parallel Port), EPP (Enhanced Parallel Port), ECP (Extended Capabilities Port) and ECP+EPP. SPP allows data output only. Extended Capabilities Port (ECP) and Enhanced Parallel Port (EPP) are bi-directional modes, allowing both data input and output. ECP and EPP modes are only supported with EPP- and ECP-aware peripherals. ECP Mode Use DMA (3) When the onboard parallel port is set to ECP mode, the parallel port can use DMA 3 or DMA 1. Press <Esc> to return to the Integrated Peripherals screen.
37
Wake Up Calls
If the system is suspended, or has been powered down by software, it can be resumed by a wake up call that is generated by incoming traffic to a modem, a LAN card, a PCI card, or a fixed alarm on the system realtime clock.
PM Wake Up Events
This item opens a submenu that enables you to set events that will resume the system from a power saving mode. Scroll to this item and press <Enter> to view the following screen:
IRQ [3-7, 9-15], NMI (Enabled) This option determines whether any activity for IRQ 3-7/9-15 will cause the system to wake from a power saving mode. IRQ 8 Break Suspend (Disabled) Determines whether the system will monitor IRQ 8 activity and wake the system from a power saving mode when IRQ 8 is activated.
39
Resume By Ring (Disabled) An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) awakens the system from a soft off state. MACPME Power Up Control (Disabled) Use this item to enable MAC activity to wakeup the system from a power saving mode. Resume By PCI PME (Enabled) This item specifies whether the system will be awakened from power saving modes when activity or input signal of the specified hardware peripheral or component is detected. Power Up by Alarm (Disabled) When set to Enabled, the following three fields become available: Month Alarm, Day of Month, and Time Alarm Upon arrival of the alarm time, it will instruct the system to wake up. When set to 0 (zero) for the day of the month, the alarm will power on your system every day at the specified time. **Reload Global Timer Events** These fields determine which events waken the system from power saving mode. Primary/Secondary IDE (Disabled) When this item is enabled, the system power will resume the system from a power saving mode if there is any activity on primary or secondary IDE channels 0 and 1. FDD, COM, LPT Port (Disabled) When this item is enabled, the system will restart the power-saving timeout counters when any activity is detected on the floppy disk drive, serial ports, or the parallel port. PCI PIRQ [A-D]# (Disabled) When this item is enabled, any activity from one of the listed devices wakes up the system. Press <Esc> to return to the Power Management Setup screen.
40
PNP/PCI Configurations
This section describes configuring the PCI bus system. PCI (Peripheral Component Interconnect) is a system, which allows I/O devices to operate at speeds nearing CPUs when they communicate with own special components. All the options describes in this section are important and technical and it is strongly recommended that only experienced users should make any changes to the default settings.
PC Health Status
On motherboards that support hardware monitoring, this item lets you monitor the parameters for critical voltages, critical temperatures, and fan speeds.
42
Frequency/Voltage Control
This item enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.
43
45
Chapter 4
Note: If the opening screen doesn't appear, double-click the file "setup.exe" in the root directory. 46
Setup Tab
Setup Browse CD Click the Setup button to run the software installation program. Select from the menu which software you want to install. The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support CD. Before installing the software from Windows Explorer, look for a file named README.TXT, INSTALL.TXT or something similar. This file may contain important information to help you install the software correctly. Some software is installed in separate folders for different operating systems, such as DOS, WIN NT, or WIN98/95. Always go to the correct folder for the kind of OS you are using. To install the software, execute a file named SETUP.EXE or INSTALL.EXE by double-clicking the file and then following the instructions on the screen. Exit The Exit button closes the Auto Setup window.
Application Tab
Lists the software utilities that are available on the CD.
Read Me Tab
Displays the path for all software and drivers available on the CD.
Running Setup
Follow these instructions to install device drivers and software for the motherboard: 1. Click Setup. The installation program begins:
47
Note: The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing. The motherboard identification is located in the upper left-hand corner. 2. Click Next. The following screen appears:
3. 4.
Check the box next to the items you want to install. The default options are recommended. Click Next run the Installation Wizard. An item installation screen appears:
5.
Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation.
48
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard. Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder. If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.
WinFlash Utility
The Award WinFlash utility is a Windows version of the DOS Award BIOS flash writer utility. The utility enables you to flash the system BIOS stored on a Flash Memory chip on the motherboard while in a Windows environment. This utility is currently available for WINXP\ME\2000\98SE. To install the WinFlash utility, run WINFLASH.EXE from the following directory: \UTILITY\WINFLASH 1.51
PC-CILLIN
The PC-CILLIN software program provides anti-virus protection for your system. This program is available for Windows 2000/ME/98SE/XP and Windows NT. Be sure to check the readme.txt and install the appropriate anti-virus software for your operating system. We strongly recommend users to install this free anti-virus software to help protect your system against viruses.