Professional Documents
Culture Documents
Design of Doubly Reinforced Beam Under Floor Slab (B11 & B01)
Design of Doubly Reinforced Beam Under Floor Slab (B11 & B01)
1. DATA Clear span (lx) Width of support fck fy 2. PRIMERY DIAMENSIONS Assume d = = = 162.5mm = = = = 3.9m 200mm 20N/mm2 415N/mm2
provide Effective depth (d) Over all depth (D) Breadth = = = 170mm 170+30 = 200mm 200
3.EFFECTIVE SPAN CALCULATION As per clouse 22.2 of IS 456-2000 Effective span (lx) L+d = = C/C distance = = 3.9+0.17 4.07 3.9+0.2 4.1
Provide Effective span 4. LOAD CALCULATION Dead load of slab = Weathering Live load = = =
= 4.07m
1x0.125x25
3.125 KN/m2 0.5 KN/m2 0.75 KN/m2 = 4.375 KN/m2 =6.29754.375 = 27.56 KN/m
Total load acting on slab Load per meter run on the beam
Total load
Design load
MU1
= = =
Ast1
= = Ast2 = = = Total Ast = = = Min Ast ` = = = Max Ast = = = Provide 28mm dia. bars, 3 163.85mm2 0.04bD 0.04X200X440 3520mm2 1979.8 mm2 Ast1+ Ast2 765.7+1979.8 2745.7 mm2 2042.3 mm2
No. of bars
= =
provide 5nos. of 28mm dia. as tensile reinforcement Using 28mm dia. bars as compression reinforcement No. of bars = = = Provide Asc = = 3.31 4
4 x 615.44 2461.76mm2
provide 4nos. of 28mm dia. as compression reinforcement 8. CHECK FOR SHEAR Shear force (Vu) = = = 222.96 KN Nominal shear stress ( ) = = = % of steel = = 4 2.78 N/mm2
3.84%
0.28 N/mm2
Hence,
>
>
Then shear reinforcement is designed Design of shear reinforcement (Vus) = = = Using 6mm dia. 2 legged vertical stirrups Asv Spacing (Sv) = = = = As per cl. 26.5.1.5 of IS 456-2000 Maximum spacing = = = As per cl. 26.5.1.6 of IS 456-2000 spacing = = = 5 103.74mm 0.75d 0.75 x 400 300mm 103.74mm 113.04 mm2 Vu 222.96- (0.8X200X400) 157.36 KN
Max spacing
= = =
Min spacing
= = = 510.16mm
provide 6mm dia. 4 legged vertical stirrups @ 100mm c/c 8. CHECK FOR DEVELOPMENT LENGTH M R is offered by 3nos. of 20mm dia. bars M1 = = = vu As per clause 26.2.3.3 of IS 456:2000 Ld < [1.3 ] + L0 = 0.87 fy Ast [d ] ]
Assuming bearing for 200 mm straight length beyond can be of support = = L0 = = = = Here 20 80mm 80 + Anchorage value @ 900 80 + 8 80 + (8 X 20) 240 mm = 6 [1.3 X ] + 240
[ 1.3 ] + L0
1728.71mm
940 mm