Professional Documents
Culture Documents
The setup
The setup is very simple, just an ordinary trafo connected to a battery switched with a 2n3055
transistor controlled by compute interface. The secondary of the trafo is connected to a
capacitor thought a diode 1n4007.
The capacitor is discharged into a load using a SCR controlled with this circuit
http://postimage.org/image/asizfh44f/.
The reference voltage to control the previous circuit is delivered for the secondary of the trafo.
Experimental results
First changing the frequency and register the current input and DC voltage on secondary more
diode. All voltage are measured with a digital multimeter
V in
(V)
6
6
6
6
6
6
6
6
dutycycle
50
50
50
50
50
50
50
50
freq.
Hz
30
35
40
45
50
55
60
65
I in (A)
0,43
0,48
0,52
0,57
0,61
0,65
0,64
0,6
Vout
voltimeter
30
33
38
41
45
50
52
53
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
70
75
85
95
100
110
120
140
150
180
230
250
300
350
400
500
700
1200
2000
0,57
0,55
0,52
0,51
0,51
0,52
0,55
0,64
0,68
0,83
1,05
1,12
1,3
1,46
1,6
1,83
2,23
2,8
3,28
54
55
57
60
61
64
68
75
77
80
84
85
88
90
92
92
89
74
50
Vout vs freq
100
80
60
40
20
0
0
200
400
600
800
1000
1200
1400
1600
1800
2000
1400
1600
1800
2000
Iin vs freq
3,5
3
2,5
2
1,5
1
0,5
0
0
200
400
600
800
1000
1200
Vout vs Iin
100
80
60
40
20
0
0
0,5
1,5
2,5
3,5
Now I use always the half diode-plug by Hector Perez in the follows setups.
Next I change the frequency and I register the DC voltage on the capacitor with the multimeter
and with a shunt, so the load impedance equal to zero. The capacitor here is always 2.2uF.
V in
(V)
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
freq. (Hz)
30
40
45
50
55
60
65
70
75
80
100
110
120
150
200
270
320
380
450
530
600
650
duty
cycle
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
I in (A)
0,4
0,51
0,55
0,6
0,66
0,73
0,79
0,85
0,9
0,95
1,13
1,2
1,29
1,47
1,7
1,9
1,97
2,05
2,14
2,21
2,27
2,33
Vcap voltimeter
(V)
60
35
29
20
12
8
7
6
4
3,5
0,8
0,2
0,48
1,1
1,2
0,2
0,7
1,3
1,8
2,4
2,7
2,85
load
cap
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
6
6
6
6
6
1000
1100
1200
1400
2000
50
50
50
50
50
2,57
2,64
2,76
2,8
3
3
2,6
4
3,5
4,9
shunt
shunt
shunt
shunt
shunt
2.2 u
2.2 u
2.2 u
2.2 u
2.2 u
Vcap vs freq
80
60
40
20
0
0 100 200 300 400 500 600 700 800 900 10001100120013001400150016001700180019002000
I in vs freq
4
3
2
1
0
0
200
400
600
800
1000
1200
1400
1600
1800
2000
Next I fix the frequency and change the capacitance values of the capacitor. I think the best
value is 222nF were the half resonance happens and the joules collected are maximum.
V in
freq.
6
6
6
6
6
6
6
6
6
150
150
150
150
150
150
150
150
150
duty
cycle
50
50
50
50
50
50
50
50
50
load
I in
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
shunt
1,85
1,54
1,24
1,03
1
0,92
0,87
0,86
0,85
Vcap
voltimeter
0,2
1,2
1,9
18
24
42
45
45,5
46
cap
10u
2,2u
1u
500n
330n
220n
100n
68n
39n
At last I put a 12V 21W car bulb instead the shunt and tried analyze the shine with my eyes.
V in
freq.
6
6
6
6
6
150
150
150
150
150
duty
cycle
50
50
50
50
50
load
I in
1,7
1,31
1,09
0,99
0,96
Conclusions
I pretend get more power on the output that what I put in.
I will be very grateful for yours answers, ideas and opinions
Vcap
voltimeter
10
25
33
40
40
cap
BRILHO
10u
2,2u
1u
500n
330n
X
more
X (again)
less
nothing