Professional Documents
Culture Documents
1 2006 Avalon
1 2006 Avalon
ES37
TERMINALS OF ECM
1. SFI SYSTEM
B45
B46
B47
D41
A24
G035613E15
HINT: The standard normal voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated. The check results should be compared with the standard normal voltage for that pair of terminals, listed in the STD Voltages column. The illustration above can be used as a reference to identify the ECM terminal locations.
Symbols (Terminal No.) +B (A24-1) - E1 (B47-1) +B2 (A24-2) - E1 (B47-1) BATT (A24-3) - E1 (B47-1) Wiring Colors L - BR R - BR B - BR Terminal Descriptions Power source of ECM Power source of ECM Battery (for measuring the battery voltage and for the ECM memory) Vent valve operation signal (built into pump module) Vacuum pump operation signal (built into pump module) Vacuum pump operation signal (built into pump module) Power source of ETCS throttle motor EFI relay operation signal Ignition switch signal C/OPEN relay operation signal (fuel pump control) Stop light switch signal Stop light switch signal Stop light switch signal (opposite to STP terminal) Stop light switch signal (opposite to STP terminal) ACC relay control signal Accelerator pedal position sensor signal (for engine control) Conditions Ignition switch on (IG) Ignition switch on (IG) Always STD Voltages 9 to 14 V 9 to 14 V 9 to 14 V
ES
W - BR
9 to 14 V
G - BR
0 to 3 V
G - BR
Vacuum pump ON
9 to 14 V
+BM (A24-7) - E1 (B47-1) MREL (A24-8) - E1 (B47-1) IGSW (A24-9) - E1 (B47-1) FC (A24-10) - E1 (B47-1) STP (A24-15) - E1 (B47-1) STP (A24-15) - E1 (B47-1) ST1- (A24-16) - E1 (B47-1) ST1- (A24-16) - E1 (B47-1) ACCR*2 (A24-17) - E1 (B47-1) VPA (A24-18) - EPA (A24-20)
V - BR V - BR Y - BR O - BR W - BR W - BR GR - BR GR - BR B - BR W - LG
Always Ignition switch on (IG) Ignition switch on (IG) Ignition switch on (IG) Brake pedal depressed Brake pedal released Ignition switch on (IG), Brake pedal depressed Ignition switch on (IG), Brake pedal released Cranking Ignition switch on (IG), Accelerator pedal fully released
9 to 14 V 9 to 14 V 9 to 14 V 9 to 14 V 7.5 to 14 V Below 1.5 V Below 1.5 V 7.5 to 14 V Below 1.5 V 0.5 to 1.1 V
ES38
Symbols (Terminal No.) VPA (A24-18) - EPA (A24-20)
R - L-B
1.2 to 2.0 V
R - L-B
3.4 to 5.0 V
LG - W
0.5 to 1.1 V
ES
LG - W
2.6 to 4.5 V
L-B - R
1.2 to 2.0 V
L-B - R
3.4 to 5.0 V
V-W P - BR B - LG
L - L-B
4.5 to 5.0 V
BR - BR
Always
Below 1 Pulse generation (see waveform 11) 10 to 16 V 6.6 to 10.1 V 4.5 to 7.1 V 2.3 to 4.0 V Below 1 V Below 1 V 10 to 14 V Pulse generation (see waveform 8) Below 3.0 V
W - BR
Idling Ignition switch on (IG) CANCEL switch ON SET/COAST switch ON RES/ACC switch ON Main switch ON Ignition switch on (IG) Cruise control main switch ON MODE switch ON MODE switch OFF Ignition switch on (IG), Rotate driving wheel slowly Ignition switch on (IG)
B - BR
CCHG*3
(D41-4) - E1 (B47-1)
Y - BR
Distance control switch signal Vehicle speed signal from combination meter Malfunction Indicator Lamp (MIL) operation signal Malfunction Indicator Lamp (MIL) operation signal Airbag sensor assembly CAN communication circuit CAN communication circuit Earth (ground) circuit of ECM
GR - BR
W (D41-30) - E1 (B47-1)
R - BR
W (D41-30) - E1 (B47-1)
R - BR
Idling
F/PS (D41-32) - E1 (B47-1) CANH (D41-33) - CANL (D41-34) CANL (D41-34) - CANH (D41-33) E1 (B47-1) - Body ground
R - BR G-W W-G BR - -
Idling with warm engine Ignition switch off Ignition switch off Always
ES39
STD Voltages
9 to 14 V
Idling
P/S pressure switch signal Starter relay operation signal Starter relay operation signal Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) Camshaft timing Oil Control Valve (OCV) operation signal (Intake side) Variable Valve Timing (VVT) sensor signal (Intake side) Variable Valve Timing (VVT) sensor signal (Intake side) Crankshaft position sensor signal Crankshaft position sensor signal Variable Valve Timing (VVT) sensor signal (Exhaust side) Variable Valve Timing (VVT) sensor signal (Exhaust side) Variable Valve Timing (VVT) sensor signal (Exhaust side) Variable Valve Timing (VVT) sensor signal (Exhaust side) Camshaft timing Oil Control Valve (OCV) operation signal (Exhaust side)
9 to 14 V 9 to 14 V 9 to 14 V
ES
L-B - BR
BR - L-B
L-Y
Y-L
P-L
Idling
Pulse generation (see waveform 5) Pulse generation (see waveform 5) Pulse generation (see waveform 5) Pulse generation (see waveform 5) Pulse generation (see waveform 5) Pulse generation (see waveform 5) Pulse generation (see waveform 5) Pulse generation (see waveform 5)
G-R
Idling
B-W W-B
Idling Idling
R-L
Idling
L-R
Idling
W-B
Idling
B-W
Idling
W-R - B-W
ES40
Symbols (Terminal No.)
G-R - W-L
L-P
Idling
R-G
Idling
B-W - W-R
ES
OE2- (B47-32) - OE2+ (B47-27) W-L - G-R HT1B (B45-1) - E1 (B47-1) HT2B (B46-5) - E1 (B47-1) HT1B (B45-1) - E1 (B47-1) HT2B (B46-5) - E1 (B47-1) ACM (B45-3) - E1 (B47-1) R - BR R - BR R - BR R - BR G - BR
Below 3.0 V 9 to 14 V
9 to 14 V
W - W-B
Pulse generation (see waveform 10) Pluse generation (see waveform 9) Below 1 V Below 1 V
B - W-B
E02 (B45-6) - Body ground E01 (B45-7) - Body ground IGT1 (B45-8) - E1 (B47-1) IGT2 (B45-9) - E1 (B47-1) IGT3 (B45-10) - E1 (B47-1) IGT4 (B45-11) - E1 (B47-1) IGT5 (B45-12) - E1 (B47-1) IGT6 (B45-13) - E1 (B47-1) GE01 (B45-17) - E1 (B47-1) OX1B (B45-18) - E2 (B45-28) OX2B (B46-33) - E2 (B45-28) VTA2 (B45-19) - E2 (B45-28)
Always Always
Idling
Shielded earth (ground) circuit of throttle drive motor Heated oxygen sensor signal Throttle position sensor signal (for sensor malfunction detection) Throttle position sensor signal (for sensor malfunction detection) Throttle position sensor signal (for engine control) Throttle position sensor signal (for engine control) Engine coolant temperature sensor signal Intake air temperature sensor signal
Always With engine speed at 2,500 rpm for 2 minutes after warming up Ignition switch on (IG), Accelerator pedal fully released Ignition switch on (IG), Accelerator pedal fully depressed Ignition switch on (IG), Throttle valve fully closed Ignition switch on (IG), Throttle valve fully open Idling, Engine coolant temperature 80C (176F) Idling, Intake air temperature 20C (68F)
L-B - W
4.5 to 5.0 V
VTA1 (B45-20) - E2 (B45-28) VTA1 (B45-20) - E2 (B45-28) THW (B45-21) - E2 (B45-28) THA (B45-22) - E2 (B45-28)
ES41
STD Voltages 4.5 to 5.0 V
W - BR
4.5 to 5.0 V
W - BR
Idling
P - BR W - BR
W-R - BR
Always Idling, Shift lever position P or N, A/C switch OFF Ignition switch on (IG)
Below 1 V
ES
R - W-R
0.5 to 3.0 V
L - BR
9 to 14 V
PRG (B45-34) - E1 (B47-1) PRG (B45-34) - E1 (B47-1) HA2A (B46-1) - E05 (B46-6) HA2A (B46-1) - E05 (B46-6) HA1A (B46-2) - E04 (B46-7) HA1A (B46-2) - E04 (B46-7) ME01 (B46-3) - E1 (B47-1) E03 (B46-4) - E1 (B47-1) HT2B (B46-5) - E1 (B47-1) HT1B (B45-1) - E1 (B47-1) HT2B (B46-5) - E1 (B47-1) HT1B (B45-1) - E1 (B47-1) E05 (B46-6) - E1 (B47-1) E04 (B46-7) - E1 (B47-1) STAR (B46-8) - E1 (B47-1) STAR (B46-8) - E1 (B47-1) EKN2 (B46-20) - KNK2 (B46-21) KNK2 (B46-21) - EKN2 (B46-20) A1A+ (B46-22) - E1 (B47-1) A1A+ (B46-22) - E1 (B47-1) A2A+ (B46-23) - E1 (B47-1) A2A+ (B46-23) - E1 (B47-1)
G - BR G - BR B - W-B B - W-B L - W-B L - W-B W-B - BR W-B - BR R - BR R - BR R - BR R - BR W-B - BR W-B - BR W-R - BR W-R - BR G-R R-G BR - BR BR - BR P - BR P - BR
Ignition switch on (IG) Idling Idling Ignition switch on (IG) Idling Ignition switch on (IG) Always Always Idling Ignition switch on (IG) Always Always Ignition switch on (IG), Shift lever position P or N Ignition switch on (IG), Shift lever position other than P or N With engine speed at 4,000 rpm after warming up With engine speed at 4,000 rpm after warming up Ignition switch on (IG) Ignition switch on (IG) Ignition switch on (IG) Ignition switch on (IG)
9 to 14 V Pulse generation (see waveform 7) Below 3.0 V 9 to 14 V Below 3.0 V 9 to 14 V Below 1 V Below 1 V Below 3.0 V 9 to 14 V Below 1 V Below 1 V Below 3.0 V 9 to 14 V Pulse generation (see waveform 4) Pulse generation (see waveform 4) 3.3 V*1 3.0 V*1 3.3 V*1 3.0 V*1
ES42
Symbols (Terminal No.) EKNK (B46-28) - KNK1 (B46-29) KNK1 (B46-29) - EKNK (B46-28) A1A- (B46-30) - E1 (B47-1) A1A- (B46-30) - E1 (B47-1) A2A- (B46-31) - E1 (B47-1) A2A- (B46-31) - E1 (B47-1) OX2B (B46-33) - E2 (B45-28) OX1B (B45-18) - E2 (B45-28)
ES
: The ECM terminal voltage is constant regardless of the output voltage from the sensor. *2 : With Smart Key system *3 : With Dynamic Radar Cruise Control system
5 V/DIV
*1
(a) WAVEFORM 1 (1) Camshaft timing Oil Control Valve (OCV) operation signal
ECM Terminal Names Between OC1+ and OC1- , OC2+ and OC2- , OE1+ and OE1- , or OE2+ and OE25 V/DIV, 1 msec./DIV Idling
Ground
1 msec./DIV
A093229E14
HINT: The wavelength becomes shorter as the engine rpm increases. (b) WAVEFORM 2 (1) Heated oxygen sensor signal
ECM Terminal Names Tester Ranges Conditions Between OX1B and E2, or OX2B and E2 0.2 V/DIV, 200 msec./DIV Engine speed is maintained at 2,500 rpm for 2 minutes after sensor is warmed up
0.2 V/DIV
HINT: In the DATA LIST, item O2S B1S2 shows the ECM input values from the heated oxygen sensor. (c) WAVEFORM 3 (1) Fuel injector operation signal
ECM Terminal Names Tester Ranges Conditions Between #10 (to 60) and E01 30 V/DIV, 20 msec./DIV Idling
30 V/DIV
Ground
20 msec./DIV
ES43
Ground
Conditions
1 msec./DIV
A085286E30
HINT: The wavelength becomes shorter as the engine rpm increases. The waveforms and amplitudes displayed differ slightly depending on the vehicle. (e) WAVEFORM 5 (1) Variable Valve Timing (VVT) sensor signal (1) (2) Crankshaft position sensor signal (2)
ECM Terminal Names (1) Between VV1+ and VV1- , VV2+ and VV2-, EV1+ and EV1-, or EV2+ and EV2(2) Between NE+ and NE5 V/DIV, 20 msec./DIV Idling
5 V/DIV
(2) NE (1) VV1 or EV1 VV2 or EV2 20 msec./DIV (Idling)
ES
HINT: The wavelength becomes shorter as the engine rpm increases. (f) WAVEFORM 6 (1) Igniter IGT signal (from ECM to igniter) (1) (2) Igniter IGF signal (from igniter to ECM) (2)
(1) Between IGT (1 to 6) and E1 (2) Between IGF1 and E1 2 V/DIV, 20 msec./DIV Idling
2 V/DIV (1)
Ground
(2)
Ground 20 msec./DIV
G035664E06
HINT: The wavelength becomes shorter as the engine rpm increases. (g) WAVEFORM 7 (1) Purge VSV for EVAP system operation signal
ECM Terminal Names Tester Ranges Conditions Between PRG and E1 10 V/DIV, 50 msec./DIV Idling
10 V/DIV
Ground
50 msec./DIV
G042964E01
HINT: If the waveform is not similar to that shown in the illustration, check the waveform again after idling for 10 minutes or more.
ES44
2 V/DIV
Ground
20 msec./DIV
A093224E14
HINT: The wavelength becomes shorter as the vehicle speed increases. Depending on the vehicle, the output waveform voltage may rise to 12 V if influenced by optionally installed systems. (i) WAVEFORM 9 (1) Throttle drive motor operation signal (positive terminal)
Between M+ and ME01 5 V/DIV, 1 msec./DIV Idling with warm engine
ES
5 V/DIV
Ground 1 msec./DIV
A093274E16
HINT: The duty ratio varies depending on the throttle actuator operation. (j) WAVEFORM 10 (1) Throttle drive motor operation signal (negative terminal)
Between M- and ME01 5 V/DIV, 1 msec./DIV Idling with warm engine
5 V/DIV
Ground 1 msec./DIV
A093275E15
HINT: The duty ratio varies depending on the throttle actuator operation. (k) WAVEFORM 11 (1) Engine speed signal
ECM Terminal Names Tester Ranges Conditions Between TACH and E1 5 V/DIV, 10 msec./DIV Idling
5 V/DIV
Ground
10 msec./DIV
ES45
(l)
5 V/DIV
Ground
500 msec./DIV
A093227E06
ES