Professional Documents
Culture Documents
HSM
Keyless Taper-Grip Bushing supplied as standard in popular AGMA bore sizes and in metric. Optional keyed hollow bore is also available.
Breather Plug With integral sealing washer and built-in non-return valve.
Gears Helical, Involute form, alloy steels, gas carburized and hardened, shaved and honed (profile ground on selected sizes) insuring low noise emission. The hunting tooth principle adopted to insure maximum working life.
Shafts Machined from alloy steels and precision ground on journals, gear seatings and extensions. Tolerances and keyways conform to international standards.
Additional Case Lugs Eliminate the need for critical tightening of torque arm bolts. Control position of standard torque arm mounting to within recommended limits. Rubberized End Caps Self-sealing intermediate cover plates, to standard ISO housing dimensions. Drain Plugs With integral sealing washer. Backstops (anti-run back device) available on all units as an add-on option.
HSM Shaft Mount Speed Reducers are shipped without oil. Before running they should be filled with an appropriate amount of the correct lubricant as shown in the tables.
Table 4. Approximate Oil Quantity (gallons) Required for Mounting Positions
Unit Size Approximate Capacity (gallons) Ratio = 5:1 Mounting Position 1 107C 115D 203E 207F 215G 307H 315J 407S 415K 507L 608M 0.13 0.21 0.32 0.66 0.87 1.08 1.51 2.88 4.02 2 0.13 0.24 0.45 0.69 0.85 1.40 2.27 4.86 5.73 3 0.13 0.21 0.37 0.63 0.85 1.08 1.56 3.59 6.66 4 0.16 0.26 0.48 0.66 0.87 1.53 2.27 4.86 5.47 1 0.11 0.18 0.26 0.61 0.79 1.00 1.43 2.40 3.36 5.94 9.51 Ratio = 14:1, 20:1 and 25:1 Mounting Position 2 0.16 0.24 0.48 0.69 0.85 1.45 2.25 4.33 5.73 9.11 13.2 3 0.13 0.21 0.37 0.63 0.85 1.11 1.56 3.33 4.15 13.7 20.9 4 0.16 0.24 0.42 0.58 0.85 1.35 2.19 4.07 5.07 7.13 11.9
Lubrication
Filter plug
Level plug
Drain plug
Units are fitted with filter, level and drain plugs generally in the position shown.
Recommended Lubricants
Table 5. Mineral Oil
5:1 RATIO REDUCERS Ambient Temp. F 0-100 RPM 101-200 RPM 201-400 RPM 0-20 RPM 14, 20 & 25:1 RATIO REDUCERS 21-50 RPM 51-120 RPM 0-50 RPM 51-80 RPM
107C-407S 107C-407S
14 to 40 41 to 80 81 to 105
Note: Do not use E.P. mineral oils other than those recommended when using a backstop.
Taper-Grip Bushing
Table 1. Taper-Grip Bushing Screw Torques SM-Shaft Mount Size 107C 115D 203E 207F 215G 307H 315J 407S 415K 507L 608M Original Taper-Grip Bushing Screw Torque Nm 31 31 51 51 128 245 245 245 245 245 245 lb. ft. 23 23 37.5 37.5 94 180 180 180 180 180 180 New STEEL Taper-Grip Bushing Screw Torque Nm 50 55 75 140 250 300 300 300 250 250 250 lb. ft. 37 41 56 104 185 223 223 223 185 185 185 Table 2. Shaft Tolerances Shaft Dia. 3/4 - 1 1/8 1 3/16 - 2 2 1/16 - 3 1/8 3 3/16 - 4 3/4 4 13/16 - 6 1/2 Tolerance +0 -.005 +0 -.006 +0 -.007 +0 -.008 +0 -.009
Standard
Taper-Grip