Professional Documents
Culture Documents
Book 1 of 12: Part 1 Structural steel calculation (02ME-5400) C03-001 Structural design calculation (02ME-5400) Wrong content, Vendor to update approved one Lifting calculation section can be excluded
PLEASE FIND ATTACHED FILE FOR REPLACEMENT. Structural steel calculation (01ME-5300) C03-002 Structural design calculation (01ME-5300) Wrong content, Vendor to update approved one Lifting calculation section can be excluded
PLEASE FIND ATTACHED FILE FOR REPLACEMENT Doc C06-001 Vessel Design Calculation (02ME-5400) Design calculation for Utility Gas Scrubber (02V-5420) Design calculation for Utility Gas Filter/ Coalescer (02V-5430A) Design calculation for Utility Gas Filter/ Coalescer (02V-5430B) Doc No.: DC12118-08 Design calculation for Instrument Gas Filter (02V-5440) Design calculation for Fuel Gas Heater (01H-5310)
THESE DOCUMENTS ARE ALREADY APPROVED (CODE 1) by MES. THERE SHOULD NOT BE ANY CHANGES/REVISE ON THESE DOCUMENTS. AND ALSO, THESE DESIGN DOCUMENTS ARE REVIEWD BY APPLIED ENGINEERING QC AND BV MALAYSIA. Book 2 of 12: Doc C06-001 Vessel Design Calculation (01ME-5300) Design calculation for Fuel Gas Scrubber (01V-5320) Design calculation for Fuel Gas Filter (01V-5330A) Design calculation for Fuel Gas Filter (01V-5330B)
Page 1 of 5
Doc C06-003 Instrument Gas Cooler Design Calculation (02ME-5400) SAME AS ABOVE REPLY.
Doc C13-001 HST&HSD Equipment Sizing Calculation (01ME-5300 & 02ME-5400) Heater datasheet: vendor to attach in Mechanical equipment datasheet (G08-001)
PLEASE FIND ATTACHED. Book 7 of 12: Section P: Part 7 Site acceptance test (SAT) and offshore commissioning procedures/ HST 01ME-5300 It is SAT report. Vendor to attach cover page to sign Vendor to attach SAT procedure separately
PLEASE FIND ATTACHED 02ME-5400 It is SAT report. Vendor to attach cover page to sign Vendor to attach SAT procedure separately
PLEASE FIND ATTACHED Part 13: Vessel detail drawing (02ME-5400) Vendor to refer comment on Book 11 of 12 (Section P: Manufacturers data report by Applied Eng). These drawings shall be same
THESE DRAWINGS ARE FABRICATION SHOP DRAWINGS; THEY ARE USED FOR FABRICATION AND AS-BUILT ENDORESED BY APPLIED ENGINEERING. THESE DRAWINGS CANNOT BE THE SAME AS FINAL CODE 1 APPROVAL DRAWINGS. Part 14: Vessel detail drawing (01ME-5300 instead of 02ME-5300) Vendor to refer comment on Book 9, 10 of 12 (Section P: Manufacturers data report by Applied Eng). These drawings shall be same
THESE DRAWINGS ARE FABRICATION SHOP DRAWINGS; THEY ARE USED FOR FABRICATION AND AS-BUILT ENDORESED BY APPLIED ENGINEERING. THESE DRAWINGS CANNOT BE THE SAME AS FINAL CODE 1 APPROVAL DRAWINGS.
Page 2 of 5
Book 8 of 12: D29-002 Valve list It is not approved document. Vendor to attach approved one
PLEASE FIND ATTACHED. G15-002 HSD Instrument Datasheet Wrong content (Instrument list?)
XXXX M01-001 Operation and Maintenance manual (01ME-5300) Vendor to revise as per comment on document No.M01-001 Rev A
PLEASE FIND ATTACHED. M01-002 Operation and Maintenance manual (02ME-5400) Vendor to revise as per comment on document No.M01-002 Rev A
PLEASE FIND ATTACHED. Book 9 of 12: Section P: Manufacturers data report by Applied Eng Fuel Gas Scrubber 01V-5320 Refer to C06-001 (Heat treatment requirement for head (Doc No.: DC12118-02 Page No.13). Vendor to revise drawing IA-1202-FGC-ME-VSD-201 (Vessel detail, nameplate drawing) to reflect Heat treatment requirement for HEAD.
THERE IS NO HEAT TREATMENT REQUIREMENT ON DC12118-02 PAGE 13 PLEASE VERIFY. Book 10 of 12: Section P: Manufacturers data report by Applied Eng Fuel Gas Filter/ Coalescer 01V-5330A
THESE DRAWINGS ARE FABRICATION SHOP DRAWINGS; THEY ARE USED FOR FABRICATION AND AS-BUILT ENDORESED BY APPLIED ENGINEERING. THESE DRAWINGS CANNOT BE THE SAME AS FINAL CODE 1 APPROVAL DRAWINGS. Fuel Gas Filter/ Coalescer 01V-5330B
THESE DRAWINGS ARE FABRICATION SHOP DRAWINGS; THEY ARE USED FOR FABRICATION AND AS-BUILT ENDORESED BY APPLIED ENGINEERING. Page 3 of 5
THESE DRAWINGS CANNOT BE THE SAME AS FINAL CODE 1 APPROVAL DRAWINGS. Fuel Gas Heater 01H-5310
THESE DRAWINGS ARE FABRICATION SHOP DRAWINGS; THEY ARE USED FOR FABRICATION AND AS-BUILT ENDORESED BY APPLIED ENGINEERING. THESE DRAWINGS CANNOT BE THE SAME AS FINAL CODE 1 APPROVAL DRAWINGS.
Book 11 of 12: Section P: Manufacturers data report by Applied Eng Utility Gas Scrubber 02V-5420 Vessel detail drawing is not approved drawing as Document D20-001. Vendor to replace approved one.
THESE DRAWINGS ARE FABRICATION SHOP DRAWINGS; THEY ARE USED FOR FABRICATION AND AS-BUILT ENDORESED BY APPLIED ENGINEERING. THESE DRAWINGS CANNOT BE THE SAME AS FINAL CODE 1 APPROVAL DRAWINGS. Refer to C06-001 (Heat treatment requirement for head ((Doc No.: DC12118-06 Page No.13). Vendor to revise drawing IA-1201-FGC-ME-VSD-101 (Vessel detail, nameplate drawing) to reflect Heat treatment requirement for HEAD.
Material name [Normalized] SA516 70 for Cylinder (Doc No.: DC12118-06 Page No.05)? No Normalized mil cert for item 21 in Material verification records 02V-5420? Vendor to correct all effected document if any (MDR, Material verification record, drawing)
THESE DOCUMENTS ARE ALREADY APPROVED (CODE 1). THERE SHOULD NOT BE ANY CHANGES/REVISE ON THESE DOCUMENTS.
Vessel detail drawing is not approved drawing as Document D20-001 RevI. Vendor to replace approved one.
Material name [Normalized] SA516 70 for Cylinder (Doc No.: DC12118-07 Page No.05)???. No Normalized mil cert for item 14 in Material verification records 02V5430A? Vendor to correct all effected document if any (MDR, Material verification record, drawing)
Refer to C06-001 (Heat treatment requirement for head (Doc No.: DC12118-07 Page No.12). Vendor to revise drawing IA-1201-FGC-ME-VSD-102 (Vessel detail, nameplate drawing) to reflect Heat treatment requirement for HEAD.
SAME AS ABOVE FEEDBACK. Book 12 of 12: Section P: Manufacturers data report by Applied Eng (continue) Utility Gas Filter 02V-5430B Same comment as 02V-5430A
Instrument Gas Filter/ Coalescer 02V-5440 In drawing IA-Y1201-FGC-ME-VSD-104 (SHT 1 OF 4): Vendor to update elevation for nozzle K1B 75mm as approved vessel detail drawing D20-001 Rev I
Page 5 of 5