Professional Documents
Culture Documents
AV-20N81
AV-16N81
AV-16N81G
SERVICE MANUAL
COLOUR TELEVISION
AV-21D81/VT
BASIC CHASSIS
CL-M
AV-20N81/VT
AV-16N81/VT
AV-16N81G/VT
[AV-20N81/VT]
[AV-16N81/VT] [AV-21D81/VT]
[AV-16N81G/VT ]
CONTENTS
SPECIFICATIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2
SAFETY PRECAUTIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 3
FEATURES・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・ 4
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
FUNCTIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・ 5
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
MAIN DIFFERENCE LIST ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・ 7
SPECIFIC SERVICE INSTRUCTIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・ 8
SERVICE ADJUSTMENTS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・ 17
PARTS LIST ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・ 33
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
★ OPERATING INSTRUCTIONS
★ STANDARD CIRCUIT DIAGRAM ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・ 2-1
・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
SPECIFICATIONS
CONTENT
ITEM
AV-21D81/VT AV-20N81/VT AV-16N81/VT /AV-16N81G/VT
UHF 471.25MHz~863.25MHz
2 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
SAFETY PRECAUTIONS
1. The design of this product contains special hardware, many 9. Isolation Check
circuits and components specially for safety purposes. For (Safety for Electrical Shock Hazard)
continued protection, no changes should be made to the original After re-assembling the product, always perform an isolation
design unless authorized in writing by the manufacturer. check on the exposed metal parts of the cabinet (antenna
Replacement parts must be identical to those used in the original terminals, video/audio input and output terminals, Control knobs,
circuits. Service should be performed by qualified personnel metal cabinet, screwheads, earphone jack, control shafts, etc.)
only. to be sure the product is safe to operate without danger of
electrical shock.
2. Alterations of the design or circuitry of the products should not be (1) Dielectric Strength Test
made. Any design alterations or additions will void the The isolation between the AC primary circuit and all metal parts
manufacturer's warranty and will further relieve the manufacturer exposed to the user, particularly any exposed metal part having a
of responsibility for personal injury or property damage resulting return path to the chassis should withstand a voltage of 3000V
therefrom. AC (r.m.s.) for a period of one second.
(. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance
3. Many electrical and mechanical parts in the products have rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated
special safety-related characteristics. These characteristics are 200V or more, for a period of one second.)
often not evident from visual inspection nor can the protection This method of test requires a test equipment not generally found
afforded by them necessarily be obtained by using replacement in the service trade.
components rated for higher voltage, wattage, etc. Replacement (2) Leakage Current Check
parts which have these special safety characteristics are Plug the AC line cord directly into the AC outlet (do not use a line
identified in the parts list of Service manual. Electrical isolation transformer during this check.). Using a "Leakage
components having such features are identified by shading Current Tester", measure the leakage current from each exposed
on the schematics and by ( ) on the parts list in Service metal part of the cabinet, particularly any exposed metal part
manual. The use of a substitute replacement which does not having a return path to the chassis, to a known good earth
have the same safety characteristics as the recommended ground (water pipe, etc.). Any leakage current must not exceed
replacement part shown in the parts list of Service manual may 0.5mA AC (r.m.s.).
cause shock, fire, or other hazards. However, in tropical area, this must not exceed 0.2mA AC
(r.m.s.).
4. Don't short between the LIVE side ground and ISOLATED z Alternate Check Method
(NEUTRAL) side ground or EARTH side ground when Plug the AC line cord directly into the AC outlet (do not use a line
repairing. isolation transformer during this check.). Use an AC voltmeter
Some model's power circuit is partly different in the GND. The having 1000 ohms per volt or more sensitivity in the following
difference of the GND is shown by the LIVE : () side GND, the manner. Connect a 1500: 10W resistor paralleled by a 0.15PF
ISOLATED(NEUTRAL) : () side GND and EARTH : () side AC-type capacitor between an exposed metal part and a known
GND. Don't short between the LIVE side GND and good earth ground (water pipe, etc.). Measure the AC voltage
ISOLATED(NEUTRAL) side GND or EARTH side GND and across the resistor with the AC voltmeter. Move the resistor
never measure with a measuring apparatus (oscilloscope etc.) connection to each exposed metal part, particularly any exposed
the LIVE side GND and ISOLATED(NEUTRAL) side GND or metal part having a return path to the chassis, and measure the
EARTH side GND at the same time. AC voltage across the resistor. Now, reverse the plug in the AC
If above note will not be kept, a fuse or any parts will be broken. outlet and repeat each measurement. Any voltage measured
must not exceed 0.75V AC (r.m.s.). This corresponds to 0.5mA
5. If any repair has been made to the chassis, it is recommended AC (r.m.s.).
that the B1 setting should be checked or adjusted (See However, in tropical area, this must not exceed 0.3V AC (r.m.s.).
ADJUSTMENT OF B1 POWER SUPPLY). This corresponds to 0.2mA AC (r.m.s.).
6. The high voltage applied to the picture tube must conform with AC VOLTMETER
that specified in Service manual. Excessive high voltage can (HAVING 1000 :/V,
cause an increase in X-Ray emission, arcing and possible OR MORE SENSITIVITY)
component damage, therefore operation under excessive high
voltage conditions should be kept to a minimum, or should be
prevented. If severe arcing occurs, remove the AC power
immediately and determine the cause by visual inspection 0.15μF AC-TYPE
(incorrect installation, cracked or melted high voltage harness,
poor soldering, etc.). To maintain the proper minimum level of PLACE THIS PROBE
soft X-Ray emission, components in the high voltage circuitry ON EACH EXPOSED
including the picture tube must be the exact replacements or 1500 : 10W METAL PART
alternatives approved by the manufacturer of the complete GOOD EARTH GROUND
product.
No.51902 3
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
FEATURES
z New chassis design enables use of an interactive on-screen control.
z Wide range voltage (Rated 110V~240V,Operated 90V~260V) AC power input.
z With AUDIO / VIDEO INPUT & OUTPUT terminal.
z MUTING button can reduce the audio level to zero instantly.
z Functional remote control to operate TV set (for channel select, volume control, power ON/OFF, etc.) from a distance.
z I2C bus control utilizes single chip ICs for IF, V/C, VSM PRESET.
z By means of AUTO PROGRAM, the TV stations can be selected automatically and the TV channels can also be rearranged automatically.
z Built-in AI ECO (ECONOMY, ECOLOGY) sensor.
In accordance with the brightness in a room, the brightness and / or contrast of the picture can be adjusted automatically to make the
optimum picture which is easy on the eye.
z Built - in ON TIMER, RETURN + & CHILD LOCK.
IC201
VIDEO/CHROMA TU001
DECORDER TUNER
IC702
MEMORY
IC701
SCL1/SDA1
SCL2/SDA2 MICRO
COMPUTER
4 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
FUNCTIONS
■ FRONT PANEL
① MENU buttons
② CHANNEL -/+ buttons
③ VOLUME -/+ buttons
④ ECO sensor
⑤ REMOTE CONTROL sensor
( AV-21D81 )
⑥ ON TIMER lamp
AV-20N81
AV-16N81/AV-16N81G
⑦ POWER lamp
⑧ MAIN POWER button
⑨ A/V INPUT terminal
AV-20N81
AV-16N81/AV-16N81G
⑨ ① ② ③ ④ ⑤ ⑥ ⑦ ⑧
■ REAR TERMINAL
① ANT Terminal
② ② VIDEO INPUT Terminal
④ ③ VIDEO OUTPUT Terminal
①
⑤ ④ AUDIO LEFT INPUT Terminal
⑥ ⑤ AUDIO RIGHT INPUT Terminal
⑦ ⑥ AUDIO LEFT OUTPUT Terminal
No. 51902 5
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
① DISPLAY key
②MENU key
MENU ▲/▼ key
MENU -/+ key
③ LIVE SPATIAL key
④ CHANNEL -/+ key
⑤ SOUND SYSTEM key
⑥ COLOUR SYSTEM key
⑦ TV / VIDEO key
⑧ PICTURE MODE key
⑨ CHANNEL SCAN key
⑩ RETURN+ key
⑪ POWER key
⑫ VOLUME -/+key
⑬ MUTING key
⑭ NUMBER (CH.) key
⑮ -/--key
⑯ OFF TIMER key
⑰ ECO SENSOR key
⑱ PICTURE BOOSTER key
6 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
Picture Tube Visible size: 51cm Visible size: 48cm Visible size: 38cm
measured diagonally measured diagonally measured diagonally
No. 51902 7
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
8 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
■ AV-21D81
FRONT CABI.
SPEAKER
C (×4)
(× )
CRT SOCKET
PWB
PW BOARD
(×4)
(× )
SPEAKER D
PWB
STOPPER
POWER
CORD
REAR
COVER
B (×2)
(× )
A (×7)
(× )
No. 51902 9
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER
1. Unplug the power plug.
2. As shown in figure, remove the 6 screws marked # and the
2 screws marked $ .
3. Withdraw the rear cover toward you.
10 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
■ AV-20N81
FRONT CABI.
SPEAKER
CRT SOCKET C
PWB (×
× 2)
PW BOARD
SPEAKER
C
(×
× 2)
POWER
CORD
REAR
COVER
B (×
× 2)
A (×
× 6)
No. 51902 11
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER
1. Unplug the power plug.
2. As shown in figure, remove the 5 screws marked # and the
2 screws marked $ .
3. Withdraw the rear cover toward you.
12 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
■ AV-16N81 / AV-16N81G
FRONT CABI.
SPEAKER
C (×
× 4)
CRT SOCKET
PWB
PW BOARD
SPEAKER
C
(×
× 4)
D
POWER
CORD PWB
STOPPER
REAR
COVER
B (×
× 2)
A (×
× 5)
No. 51902 13
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
REPLACEMENT OF MEMORY ICs
1. MEMORY ICs
This model uses memory ICs. This memory IC data are for proper operation of the video and deflection circuits.
When replacing memory ICs, be sure to use ICs written with the initial values of data.
SYSTEM CONSTANT-Ⅲ
Ⅲ
: SELECT
: OPERATE DISP : EXIT
Fig.2
14 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
SETTING OF SYSTEM CONSTANT SET
1. INCH 21 14 29 25 21
3. VIDEO INPUT 1 3 1
YES NO YES
4. ECO SENSOR
YES NO NO
9. TEXT
YES NO NO
10.COLOUR AUTO
E/V E
11.LANGUAGE E/V
MU MA MU
12.TUNER
YES NO NO
14.VNR
Table 1
Table 2
No. 51902 15
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
INITIAL SETTING VALUE OF SERVICE MENU
1. Adjustment of the SERVICE MENU is made on the basis of the initial setting values ; however, the new setting values which
set the screen in its optimum condition may differ from the initial setting.
2. Do not change the initial Setting Values of the Setting (Adjustment) items not listed In “ADJUSTMENT”.
2. V/C
RED
1. CUT OFF GREEN +00
BLUE
RED
2. DRIVE +00
BLUE
3. BRIGHT +03
4. CONT. -05
3. VSM PRESET
VSM preset
VSM mode BRIGHT STANDARD SOFT
Setting item
+19(AV-21D81/AV-20N81) +11(AV-21D81/AV-20N81)
CONT. SETTING VALUE +30
+24(AV-16N81/AV-16N81G) +17(AV-16N81/AV-16N81G)
+12(AV-21D81/AV-20N81)
SHARP SETTING VALUE +15
+10(AV-16N81/AV-16N81G)
16 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
SERVICE ADJUSTMENTS
BEFORE STARTING SERVICE ADJUSTMENT
1. There are 2 way of adjusting this TV: One is with the 7. Preparation for adjustment
REMOTE CONTROL UNIT and the other is the conventional Unless otherwise specified in the adjustment instructions, preset
method using adjustment parts and components. the following functions with the REMOTE CONTROL UNIT.
2. The adjustment with the REMOTE CONTROL UNIT is made User menu preset value
on the basis of the initial setting values. The setting values
MENU ITEM PRESET VALUE
which adjust the screen to its optimum condition may differ
from the initial setting values. PICTURE MODE (VSM) BRIGHT
3. Make sure that connection is correctly made to AC power
VNR OFF
source.
4. Turn on the power of the set and equipment before use, and TINT / COLOUR / BRIGHT /
SHARP / CONT. CENTER
start the adjustment procedures after waiting at least 30 minutes.
5. Unless otherwise specified, prepare the most suitable reception
BLUE BACK OFF
or input signal for adjustment.
6. Never touch any adjustment parts, which are not specified OFF TIMER OFF
in the list for this adjustment VRs, transforms, condensers,
ECO SENSOR OFF
etc.
AUTO SHUT OFF OFF
ADJUSTMENT ITEMS
Adjustment item
No. 51902 17
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
BASIC OPERATION OF SERVICE MENU
z The adjustment using SERVICE MENU
The following adjustment items use the SERVICE MENU in the series of the adjustment. The adjustments are made on the basis of the
initial setting values. The adjustment values which adjust the screen to the optimum condition can be different from the initial setting values.
With the SERVICE MENU, various settings can be made, and they are broadly classified in the following items of settings.
1.IF ・・・・・・・・・・・・・・・・・・・・・・・ Adjustment of the IF circuits.
2.V/C ・・・・・・・・・・・・・・・・・・・・・・ Adjustment of the VIDEO/CHROMA circuit.
3.VSM PRESET ・・・・・・・・・・・・ Adjustment of the initial setting values of VSM condition as STANDARD, SOFT and BRIGHT.
(VSM : Video Status Memory)
1.IF 2.V/C
[Exit from SERVICE MENU]
3.VSM PRESET
When complete the adjustment work, press the DISPLAY key to return to the
SERVICE MENU.
1-3 SELECT DISP : EXIT
And then press the DISPLAY key again, return to the normal screen.
***********
****** ***** ** .***
*** ** ****
** ** ***
[Select from SERVICE MENU]
In SERVICE MENU, press the number (1~3) key of the remote control unit, to select Fig.1
any of the adjustment items.
[Method of setting]
1. IF
[1. VCO]
① 1 Key・・・・・・・・・・・・・・・・・・ Select 1.IF.
② 1 Key・・・・・・・・・・・・・・・・・・ Select 1.VCO
③ The VCO (CW) screen will be displayed a allow mark when
the AFC voltage is at a certain level.
④ DISPLAY Key ・・・・・・・・・・ When this is pressed twice, you
will return to the SERVICE MENU. KEY ASSIGNMENT OF REMOTE CONTROL UNIT
18 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
SERVICE MENU FLOW CHART
*
*
*
.
*
*
VCO (CW) MHz
SERVICE MENU
IF
TOO HIGH
1.IF 2.V/C 1. VCO ABOVE REFERENCE
3.VSM PRESET BELOW REFERENCE
2. DELAY POINT
TOO LOW
*
*
AGC TAKE-OVER
Setting item
SUB MENU 2. V/C
1. CUTOFF (R/G/B)
2. DRIVE (R/B)
V/C PAL
3. BRIGHT
***
***
***
/ :SELECT BRIGHT
- / + : OPERATE DISP : EXIT CONT.
SHARP
No. 51902 19
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
ADJUSTMENT LOCATIONS
CRT SOCKET PWB (SOLDER SIDE)
TOP U
TP-47G TP-47B
TP-E
E1
F901
IC701
PW
IC702
MEMORY IC
DEG
S
IC201
S1 HV
TU001 VCO(CW)
T101
U
HVT
20 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
ADJUSTMENTS
B1 POWER SUPPLY
Measuring
Item instrument Test point Adjustment part Description
FOCUS ADJUSTMENT
Measuring
Item instrument Test point Adjustment part Description
IF CIRCUIT ADJUSTMENT
Measuring
Item instrument Test point Adjustment part Description
Adjustment Signal 1. VCO ●Please use signal generator which is correct proof about the
of VCO(CW) Generator T101
sending frequency.
(VCO.TRANSF.)
Remote 1. Input the PAL full colour bar (210.25MHz) signal.
control unit
2. Select 1.IF from the SERVICE MENU.
3. Press 1 key and select 1.VCO.
V
L
*
*
*
*
*
TOO HIGH
ABOVE REFERENCE
JUST REFERENCE
BELOW REFERENCE
TOO LOW
No. 51902 21
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
Measuring
Item instrument Test point Adjustment part Description
Adjustment Signal DELAY POINT 1. Input a black and white signal (colour off).
of DELAY generator (AGC TAKE-OVER) 2. Select 1. IF from the SERVICE MENU.
POINT Remote 3. Select 2. DELAY POINT by pressing the 2 key on the remote
(AGC) control unit control unit.
4. Set the setting values of the setting items as shown bellow table.
5. Then adjust the MENU - or + key until video noise disappears.
6. Turn to other channels and make sure that there are no
irregularities.
AGC TAKE-OVER
DELAY POINT
0~127 20
(AGC TAKE OVER)
22 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
VIDEO / CHROMA CIRCUIT ADJUSTMENT
The setting (adjustment) using the REMOTE CONTROL UNIT is made on the basis of the initial setting values.
The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
Do not change the initial setting values of the setting items not listed in “ADJUSTMENT”.
Measuring
Item instrument Test point Adjustment part Description
Adjustment Signal 1. CUT OFF (R) 1. Input a black and white signal (colour off).
of WHITE generator CUT OFF (G) 2. Select 2. V/C from the SERVICE MENU, then select 1. CUT
BALANCE Remote CUT OFF (B) OFF (R), (G) and (B) .
(Low light) control unit 3. Set each value to initial setting value with 4~9 keys of the
SCREEN VR remote control unit.
[IN HVT] 4. Press the 1 key of the remote control unit to show the single
horizontal line on screen.
5. Turn the SCREEN VR fully counter-clockwise, then slowly turn it
clockwise to where one of a red, blue or green colour is faintly
V/C PAL visible.
6. Use keys 4~9 of the remote control unit and adjust the other 2
***
***
***
1. CUTOFF (R)
(G) colours which except the appeared colour to where the single
(B) horizontal line appears white.
50Hz 7. Turn the SCREEN VR to where the single horizontal line glows
/ :SELECT faintly.
- / + : OPERATE DISP : EXIT
8. Press the 2 key to turn off the single horizontal line.
9. Press the DISPLAY key twice to return to the normal screen.
CUTOFF OFF
(H.LINE OFF) 1 2 3
CUTOFF ON
(H.LINE ON) G.CUTOFF( ▲ )
4 5 6
R. CUTOFF( ▲ ) B. CUTOFF( ▲ ) Variable Initial setting
R. DRIVE( ▲ ) B. DRIVE( ▲ ) Adjustment item range value
7 8 9
R. CUTOFF( ▼ ) B. CUTOFF( ) -128~+127
R +00
▲
R. DRIVE( ▼ ) B. DRIVE( )
▲
Adjustment Signal 2. DRIVE (R) 1. Input a black and white signal (colour off).
of WHITE generator DRIVE (B) 2. Select 2. V/C from the SERVICE MENU.
BALANCE Remote 0. Select 2. DRIVE (R) / (B) with MENU ▼/▲ key, and set each
(High light) control unit value to initial setting value with 4 and 7 or 6 and 9 keys of the
remote control unit.
4. Use the keys 4 and 7 or 6 and 9 to produce a white screen
5. Press the DISPLAY key twice to return to the nomal screen.
V/C PAL
**
**
**
2. DRIVE (R)
(B)
Variable Initial setting
Adjustment item range value
50Hz
/ :SELECT
R -128~+127 +00
- / + : OPERATE DISP : EXIT 2. DRIVE
B -128~+127 +00
No. 51902 23
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
Measuring
Item instrument Test point Adjustment part Description
NTSC 4.43 COLOUR When NTSC 3.58 adjustment completed, NTSC 4.43 will be
automatically set at the respective values.
24 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
Measuring
Item Test point Adjustment part Description
instrument
Model Voltage(W-G)
AV-21D81/VT +5V
AV-20N81/VT +7V
AV-16N81/VT +7V
AV-16N81G/VT +7V
SECAM COLOUR 1. Input a SECAM full field colour bar signal (75% white).
2. Set the initial setting value of SECAM COLOUR with the MENU
- or + key.
3. Adjust SECAM COLOUR to bring the value of (A) in the
illustration to the values as shown given billow.
Voltage difference between (W) and (G))
Model Voltage(W-G)
AV-21D81/VT +7V
AV-20N81/VT +10V
AV-16N81/VT +13V
AV-16N81G/VT +13V
NTSC 3.58 COLOUR 1. Input a NTSC 3.58 full field colour bar signal (75% white).
2. Set the initial setting value of NTSC 3.58 COLOUR with the
MENU - or + key.
3. Adjust NTSC 3.58 COLOUR to bring the value of (A) in the
illustration to the values as shown given billow.
(Voltage difference between (W) and (G))
Model Voltage(W-G)
AV-21D81/VT +5V
AV-20N81/VT +7V
AV-16N81/VT +8V
AV-16N81G/VT +8V
NTSC 4.43 COLOUR When NTSC 3.58 is set, NTSC 4.43 will be automatically set at the
respective values.
No. 51902 25
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
Measuring
Item instrument Test point Adjustment part Description
Remote NTSC 3.58 TINT 1. Input a NTSC 3.58 full field colour bar signal (75% white).
control unit 2. Select 2. V/C from SERVICE MENU.
3. Select 6. TINT with the MENU ▼/▲ key.
4. Set the initial setting value of NTSC 3.58 with the MENU - or
+ key.
5. If you cannot get the best tint with the initial setting value, make
fine adjustment until you get the best tint.
NTSC 4.43 TINT When NTSC 3.58 is set, NTSC 4.43 will be automatically set at the
respective values.
Model Voltage(W-G)
AV-21D81/VT +5V
AV-20N81/VT +7V
AV-16N81/VT +8V
AV-16N81G/VT +8V
NTSC 4.43 TINT When NTSC 3.58 is set, NTSC 4.43 will be automatically set at the
respective values.
26 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
Measuring
Item Test point Adjustment part Description
instrument
R-Y ( ▲ )
4 5 6
B-Y ( ▲ )
R-Y ( )
▲
7 8 9
B-Y ( )
▲
Adjustment Signal 35 PIN (R-Y) 7. BLACK [Method of adjustment using measuring instrument]
of BLACK generator 36 PIN (B-Y) OFFSET
OFFSET IC-301 ON 1. Receive a SECAM COLOUR bar signal (full field colour bar
(R-Y) ***
(SECAM)Ⅱ
Ⅱ Oscilloscope MAIN PWB 75% white).
(B-Y) *** 2. Select 2. V/C from SERVICE MENU.
Remote 3. Select 7. BLACK OFFSET with the FUNCTION UP/DOWN key.
control unit
4. Connect the oscilloscope between 35 pin of IC-301 and TP-E
().
5. By using 4 and 7 keys of the remote control, adjust the BLACK
[R-Y] OFFSET (R-Y) so that it becomes the waveform changes from
(a) to (b) shown in the figure.
6. Connect the oscilloscope between 36 pin of IC-301 and TP-E.
7. By using 6 and 9 keys of the remote control, adjust the BLACK
OFFSET (B-Y) so that it becomes the waveform changes from
(c) to (d) shown in the figure.
8. If the picture is not the best with the adjusted picture, make fine
(a) (b) adjustment until you get the best picture.
9. Press the MENU key and memorize the setting value.
[B-Y]
(c) (d)
No. 51902 27
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
Measuring
Item instrument Test point Adjustment part Description
Screen size
Screen Picture
size size
92% 100%
H H'
Fig.2
28 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
Measuring
Item instrument Test point Adjustment part Description
Adjustment Signal 12. V LIN. ● When the vertical linearity has been deteriorated
of V LIN. & generator 13. V. S-CR remarkably, perform the following steps.
V. S-CR Remote 10. Input a cross-hatch signal.
control unit
11. Select 12. V LIN. with the MENU ▼/▲ key.
12. Set the initial setting value of 12. V LIN. with the MENU - / +
key.
TOP 13. Select 13. V. S-CR with the MENU ▼/▲ key.
14. Set the initial setting value of 13. V. S-CR with the MENU - / +
key.
15. Adjust 12. V LIN. and 13. V. S-CR so that the spaces of each
CENTER
line as shown in Fig.3 on TOP, CENTER and BOTTOM
become uniform.
.
BOTTOM Make sure that the adjustment is properly done on the screen of
Fig.3 60Hz mode.
[NOTE]
z Adjust to make both 50Hz & 60Hz are the same v. size and
fine straight line.
z When adjust again, adjust 50Hz mode first.
z When adjust in 60Hz mode, only 60Hz mode is adjust.
Measuring
Item Test point Adjustment part Description
instrument
Setting of Remote TINT 1. Select 3. VSM PRESET from the SERVICE MENU.
VSM control unit COLOUR 2. Select BRIGHT with the PICTURE MODE key.
PRESET BRIGHT 3. Adjust the MENU ▼/▲ and MENU - or + key to bring the set
CONT. values of TINT ~ SHARP to the values shown in the below
SHARP table.
4. Respectively select the VSM PRESET mode for SOFT and
STANDARD, and make similar adjustment as in 3 above.
x VSM PRESET
TINT
COLOUR
TINT +15 ← ←
BRIGHT COLOUR +15
CONT.
← ←
SHARP BRIGHT +15 ← ←
/ :SELECT +19(AV-21D81) +11(AV-21D81)
- / + : OPERATE DISP : EXIT +19(AV-20N81) +11(AV-20N81)
CONT +30
+24(AV-16N81) +17(AV-16N81)
+24(AV-16N81G) +17(AV-16N81G)
+12(AV-21D81)
+12(AV-20N81)
SHARP +15 ← +10(AV-16N81)
+10(AV-16N81G)
No. 51902 29
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
PURITY / CONVERGENCE ADJUSTMENT
PURITY ADJUSTMENT
WEDGE
DEFLECTION
2. Loosen the retainer screw of the deflection yoke.
YOKE
CRT
4. Input a green raster signal from the signal generator, and turn 46
the screen to green raster.
P/C
5. Move the deflection yoke backward. MAGNETS
y P/C MAGNETS
6. Bring the long lug of the purity magnets on the short lug and
P : PURITY MAGNET
position them horizontally. (Fig.2) 4 : 4 POLES (convergence magnets)
6 : 6 POLES (convergence magnets)
7. Adjust the gap between two lugs so that the GREEN RASTER Fig.1
will come into the center of the screen. (Fig.3)
8. Move the deflection yoke forward, and fix the position of the
deflection yoke so that the whole screen will become green.
9. Insert the wedge to the top side of the deflection yoke so that it
will not move.
PURITY MAGNETS
Short lug
12. Input red and blue raster signals, and make sure that purity is
Bring the long lug over the short lug
properly adjusted.
and position them horizontally.
Fig.2
CENTER
Fig.3
30 No. 51902
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
Fig.1
(FRONT VIEW )
Fig.2
● After adjustment, fix the wedge at the original position. (FRONT VIEW )
Fasten the retainer screw of the deflection yoke.
Fix the 6 magnets with glue. GREEN GREEN
RED BLUE BLUE RED
RED
GREEN
BLUE
BLUE
GREEN
RED
Fig.3
No. 51902 31
AV-21D81
AV-20N81
AV-16N81
AV-16N81G
SELF CHECK FUNCTIONS
1. Outline
This model has self check functions given below. When an abnormality has been detected, the SUB POWER is turned off and the LED
flashes to inform of the failure. An abnormality is detected by the signal input state of the control line connected to the microcomputer.
Over-current protection An over-current on the LOW B The main microcomputer When an abnormality has been
line is detected. detects the possible abnormality detected, the SUB-POWER is
at 30-msec. intervals and judges turned off. While the SUB-
the results in every 16 time. Of POWER is being turned off, the
the 16 times, if NG is detected power key of the remote
more than 9 times, it is judged controller is not operational until
that there is an abnormality the power code is taken out and
put in again.
Detection of SUB-
an POWER
abnormality OFF
[ Indication by LED ]
Item LED flashing intervals Priority of detection
② CRT NECK protection / X-ray protection Slowly (at about 0.5sec.) intervals 2
[NOTE]
X-RAY : There are some different types of models with and without X-RAY PROTECTION.
LED : There are some kinds of LEDs. In the models equipped with LEDs flash (turn on and off) simultaneously. In the models with one
of the above LEDs, the LED flashes.
32 No. 51902
VICTOR COMPANY OF JAPAN, LIMITED
HOME AV NETWORK BUSINESS UNIT 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama, Kanagawa-prefecture, 221-8528, Japan