Professional Documents
Culture Documents
PPTP Server
1) We need to add the Poptop repository to our system so we'll do a "rpm -Uvh http://poptop.sourceforge.net/yum/stable/fc7/pptp-release-current.
noarch.rpm".
2) Let's install the pptp daemon "yum install pptpd"
3) "nano /etc/pptpd.conf" to open the configuration file.
4) we remove the # before "bcrelay eth1" and configure the last 2 lines (local-ip and remote-ip) to be the wanted ip ranges
5) "nano /etc/ppp/chap-secrets" and we add a new user "newuser pptpd password *"
6) "service pptpd start" and your pptp server is online!
PPTP Client
1) We need to add the Poptop repository to our system so we'll do a "rpm -Uvh http://poptop.sourceforge.net/yum/stable/fc7/pptp-release-current.
noarch.rpm".
2) "yum install pptp"
3)
Disconnect VPN
#!/bin/sh
killall -TERM pppd
Options.pptp
Server
Server
###############################################################################
#ms-wins 10.0.0.4
# Add an entry to this system's ARP [Address Resolution Protocol]
# table with the IP address of the peer and the Ethernet address of this
# system. This will have the effect of making the peer appear to other
# systems to be on the local ethernet.
# (you do not need this if your PPTP server is responsible for routing
# packets to the clients -- James Cameron)
proxyarp
# Normally pptpd passes the IP address to pppd, but if pptpd has been
# given the delegate option in pptpd.conf or the --delegate command line
# option, then pppd will use chap-secrets or radius to allocate the
# client IP address. The default local IP address used at the server
# end is often the same as the address of the server. To override this,
# specify the local IP address here.
# (you must not use this unless you have used the delegate option)
#10.8.0.100
# Logging
# Enable connection debugging facilities.
# (see your syslog configuration for where pppd sends to)
debug
# Print out all the option values which have been set.
# (often requested by mailing list to verify options)
#dump
# Miscellaneous
# Create a UUCP-style lock file for the pseudo-tty to ensure exclusive
# access.
lock
# Disable BSD-Compress compression
nobsdcomp
# Disable Van Jacobson compression
# (needed on some networks with Windows 9x/ME/XP clients, see posting to
# poptop-server on 14th April 2005 by Pawel Pokrywka and followups,
# http://marc.theaimsgroup.com/?t=111343175400006&r=1&w=2 )
novj
novjccomp
# turn off logging to stderr, since this may be redirected to pptpd,
# which may trigger a loopback
nologfd
# put plugins here
# (putting them higher up may cause them to sent messages to the pty)
Client
Client
###############################################################################
# $Id: options.pptp,v 1.3 2006/03/26 23:11:05 quozl Exp $
#
# Sample PPTP PPP options file /etc/ppp/options.pptp
# Options used by PPP when a connection is made by a PPTP client.
# This file can be referred to by an /etc/ppp/peers file for the tunnel.
# Changes are effective on the next connection. See "man pppd".
#
# You are expected to change this file to suit your system. As
# packaged, it requires PPP 2.4.2 or later from http://ppp.samba.org/
# and the kernel MPPE module available from the CVS repository also on
# http://ppp.samba.org/, which is packaged for DKMS as kernel_ppp_mppe.
###############################################################################
# Lock the port
lock
# Authentication
# We don't need the tunnel server to authenticate itself
noauth
# We won't do PAP, EAP, CHAP, or MSCHAP, but we will accept MSCHAP-V2
# (you may need to remove these refusals if the server is not using MPPE)
refuse-pap
refuse-eap
refuse-chap
refuse-mschap
# Compression
# Turn off compression protocols we know won't be used
nobsdcomp
nodeflate
# Encryption
# (There have been multiple versions of PPP with encryption support,
# choose which of the following sections you will use. Note that MPPE
# requires the use of MSCHAP-V2 during authentication)
#
# Note that using PPTP with MPPE and MSCHAP-V2 should be considered
# insecure:
# http://marc.info/?l=pptpclient-devel&m=134372640219039&w=2
# https://github.com/moxie0/chapcrack/blob/master/README.md
# http://technet.microsoft.com/en-us/security/advisory/2743314
# http://ppp.samba.org/ the PPP project version of PPP by Paul Mackarras
# ppp-2.4.2 or later with MPPE only, kernel module ppp_mppe.o
# If the kernel is booted in FIPS mode (fips=1), the ppp_mppe.ko module
# is not allowed and PPTP-MPPE is not available.
# {{{
# Require MPPE 128-bit encryption
#require-mppe-128
# }}}
# http://mppe-mppc.alphacron.de/ fork from PPP project by Jan Dubiec
# ppp-2.4.2 or later with MPPE and MPPC, kernel module ppp_mppe_mppc.o
# {{{
# Require MPPE 128-bit encryption
#mppe required,stateless
# }}}