Professional Documents
Culture Documents
Certificate Number
Report Reference
Issue Date
Issued to:
20121009-MH14882
MH14882-20121009
2012-OCTOBER-09
3M Company
3M Center
St. Paul, MN 55144
United States
Component Visibility Marking Materials
See Addendum Page 2
Have been investigated by UL in accordance with the
Standard(s) indicated on this Certificate.
Only those products bearing the UL Recognized Component Marks for the U.S. and Canada should be
considered as being covered by UL's Recognition and Follow-Up Service and meeting the appropriate U.S. and
Canadian requirements.
The UL Recognized Component Mark for the U.S. generally consists of the manufacturers identification and
catalog number, model number or other product designation as specified under Marking for the particular
Recognition as published in the appropriate UL Directory. As a supplementary means of identifying products that
have been produced under ULs Component Recognition Program, ULs Recognized Component Mark:
, may
be used in conjunction with the required Recognized Marks. The Recognized Component Mark is required when
specified in the UL Directory preceding the recognitions or under Markings for the individual recognitions. The
UL Recognized Component Mark for Canada consists of the UL Recognized Mark for Canada:
and the
manufacturers identification and catalog number, model number or other product designation as specified under
Marking for the particular Recognition as published in the appropriate UL Directory.
Recognized components are incomplete in certain constructional features or restricted in performance
capabilities and are intended for use as components of complete equipment submitted for investigation rather
than for direct separate installation in the field. The final acceptance of the component is dependent upon its
installation and use in complete equipment submitted to UL LLC.
Look for the UL Recognized Component Mark on the product.
Page 1 of 3
CERTIFICATE OF COMPLIANCE
Certificate Number
Report Reference
Issue Date
20121009-MH14882
MH14882-20121009
2012-OCTOBER-09
This is to certify that representative samples of the product as specified on this certificate were tested according
to the current UL requirements.
The following trim materials may be used to meet the minimum requirements for visibility marking materials per NFPA 19712013 and CAN/CGSB 155.1-2001:
Trim
Scotchlite 9587
Scotchlite 9687
Scotchlite 9586
Scotchlite 9686
Scotchlite 8986 NFPA
Scotchlite 8987 NFPA
Minimum
Width (in.)
Description
2
2
The following trim materials may only be used as accessory visibility markings since they do not meet the minimum
requirements for fluorescence per NFPA 1971-2013 or CAN/CGSB 155.1-2001:
Trim
Scotchlite 9587
Scotchlite 9687
Scotchlite 9586
Scotchlite 9686
Scotchlite 8935
Scotchlite 8940
Scotchlite 8735
Scotchlite 9740
Width (in.)
Description
Retroreflective
Fluorescent
<3
<3
Any
Any
Any
Any
Reflective Silver
Reflective Silver
Reflective Silver
Reflective Silver
Y
Y
Y
Y
N
N
N
N
All trim materials meet the minimum requirements for NFPA 1977-2011, NFPA 1951-2013, CAN/CGSB 155.22-1997, and
CAN/CGSB 155.20-2000.
Page 2 of 3
CERTIFICATE OF COMPLIANCE
Certificate Number
Report Reference
Issue Date
20121009-MH14882
MH14882-20121009
2012-OCTOBER-09
Title
Standard on Protective Ensembles for Structural Fire Fighting and Proximity Fire Fighting
Standard on Protective Ensembles for Technical Rescue Incidents
Standard on Protective Clothing and Equipment for Wildland Fire Fighting
Standard on Firefighters Protective Clothing for Protection Against Heat and Flame
Standard on Fireline Workwear for Forest Firefighters
Standard on Workwear for Protection Against Hydrocarbon Flash Fire
Page 3 of 3
Edition
2013
2013
2011
2001
1997
2000