Professional Documents
Culture Documents
RE 22045/05.08
Replaces: 02.03
1/14
Type M-.SED
Size 10
Component series 1X
Maximum operating pressure 350 bar [5076 psi]
Maximum flow 40 l/min [10.6 USgpm]
H4666
Table of contents
Features
Ordering code
Mating connectors
Function, section, symbols
Features
1
2, 3
3
4, 5
Technical data
Characteristic curves
Performance limit
General notes
Unit dimensions
8
9 to 13
Throttle insert
13
13
2/14
Bosch Rexroth AG
M-.SED
Hydraulics
RE 22045/05.08
Ordering code
M
SED 10
1X 350 C
=3
=4
3 main ports
4 main ports
Poppet valve
= 10
Size 10
3
Main ports
A
a
= UK
= CK
P T
A
Symbols
a
P T
A B
a
=D
=Y
P T
A B
a
P T
= available
Component series 10 to 19
(10 to 19: unchanged installation and connection dimensions)
= 1X
= 350
=C
DC voltage 24 V
DC voltage 205 V
DC voltage 96 V
For further ordering code for other voltages, see page 6
= G24
= G205 1)
= G96
AC voltage mains
(permissible voltage
tolerance 10%)
Nominal voltage of DC
voltage solenoid when
operated with AC voltage
Ordering
code
110 V - 50/60 Hz
96 V
G96
120 V - 60 Hz
110 V
G110
230 V - 50/60 Hz
205 V
G205
1)
In the case of an individual connection, a large mating connector with integrated rectifier may be used (separate order).
2)
RE 22045/05.08
M-.SED
Bosch Rexroth AG
Hydraulics
K4
3/14
No code =
V =
No code =
P=
B12 =
B15 =
B18 =
B20 =
B22 =
No code =
QMAG24 =
QMBG24 =
Electrical connection
Without mating connector
Individual connection with component plug to DINEN175301-803
For further electrical connections, see RE08010
K4 2) =
N9 =
No code =
Valve
side
Color
Without circuitry
With rectifier
12 240 V
Grey
R901017010
Black
R901017011
a/b
Black
R901017022
R901017025
R901017026
4/14
Bosch Rexroth AG
M-.SED
Hydraulics
RE 22045/05.08
Directional valves of type M-.SED are direct operated directional poppet valves with solenoid actuation. They control the
start, stop and direction of flow and basically consist of housing (1), solenoid (2), valve seats (7) and (11) and closing element (4).
Symbols
Variant UK
Variant CK
P T
b
P T
1
5
"a"
T
2
11
1
Type M-3SED 10 CK1X/350CG24N9K4
11
RE 22045/05.08
M-.SED
Hydraulics
5/14
Bosch Rexroth AG
Attention!
To avoid pressure intensification when single-rod cylinders are used, the annulus area of the cylinders must be
connected to A.
The use of the Plus-1-Plate and the seat arrangement offer
the following options:
Variant D
Variant Y
A B
A B
a
a
P T
P T
Transitional position:
When the main valve is operated, closing element (4) is
shifted against spring (5) and pressed onto seat (7). This
closes port T, while P, A and B are briefly connected.
Operated position:
P is connected to A. Because the pump pressure acts via A
onto the large area of control spool (8), ball (9) is pressed
onto seat (12). In this way, B is connected to T, and P to A.
Ball (9) in the Plus-1-Plate has a positive spool overlap.
2
6
1
11
b
5
7
Schematic illustration (starting position)
4
9
11
8
10
P
Plus-1Plate
T
B
P
10 9 12
6/14
Bosch Rexroth AG
M-.SED
Hydraulics
RE 22045/05.08
Technical data (for applications outside these parameters, please consult us!)
General
Weight
Installation orientation
Optional
Hydraulic
Maximum operating pressure
Maximum flow
Hydraulic fluid
Viscosity range
Class 20/18/15 3)
Electrical
Type of voltage
V
Available voltages 4)
DC voltage
AC voltage
% 10
Power consumption
W 30
Duty cycle
% 100
ON
OFF
temperature 5)
1) Suitable
2) Suitable
3) The
4) Special
5) Due
voltages on request
ms 20 to 50
5 to 25 (without rectifier)
30 to 50 (with rectifier)
1/h 15000
IP 65 with mating connector mounted and locked
C [F] 150 [302]
When establishing the electrical conection, properly
connect the protective earth conductor (PE ).
RE 22045/05.08
M-.SED
Hydraulics
7/14
Bosch Rexroth AG
[250]
22
20
18
16
[200]
14
12
[150]
[100]
[50]
[319]
[300]
10
8
6
4
[319]
[300]
[250]
20
18
16
[200]
14
12
[150]
[100]
[50]
2
[0]
22
10
8
6
4
2
[0] [1]
10
15
20
25
30
35
[0]
40
[0] [1]
10
3 A to T
P to B
2 A to T
10
8
[100]
[80]
[60]
[40]
[20]
[0]
2
0
12
18
35
40
4 B to T
P to A
Throttle insert
[5076]
12
30
[120]
25
1 P to A
[140]
20
[174]
[160]
15
24
30
36
42
[4500]
[4000]
[3500]
[3000]
[2500]
[2000]
[1500]
[1000]
350
B12
300
B18
B15
B20
250
200
B22
150
100
[500]
50
[0]
12
18
24
30
36
42
[0] [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11]
[0] [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11]
8/14
Bosch Rexroth AG
M-.SED
Hydraulics
RE 22045/05.08
Flow in
l/min
[USgpm]
350
[5076]
350
[5076]
40
[10.6]
350
[5076]
350
[5076]
350
[5076]
40
[10.6]
350
[5076]
350
[5076]
350
[5076]
40
[10.6]
350
[5076]
350
[5076]
350
[5076]
40
[10.6]
350
[5076]
350
[5076]
350
[5076]
350
[5076]
350
[5076]
350
[5076]
350
[5076]
Symbol
Remark
2-way circuit
A
UK
b
With a 2/2-way circuit, port
P or T must be plugged
by the customer!
P T
A
CK
a
P T
3-way circuit
A
UK
a
P T
A
CK
4-way circuit
P T
A B
D
a
P T
A B
a
P T
pP/pA/pB
40
[10.6]
pP/pA/pB
40
[10.6]
40
[10.6]
40
[10.6]
Attention!
Please observe the general notes below!
The performance limit was established when the solenoid had reached the operating temperature, at 10% undervoltage and no
precharging of the tank.
General notes
Poppet valves can be used according to the symbols and the
assigned operating pressures and flows (see Performance
limits above).
To ensure reliable operation, the following points must
strictly be observed:
Poppet valves feature a negative spool overlap, that is, during the switching process, a certain amount of leakage oil is
produced. However, this process takes place within such a
short time so that it is irrelevant in nearly all applications.
The specified maximum flow must not be exceeded (if required, install throttle insert for limiting the flow, see page 13)!
Plus-1-Plate:
When using the Plus-1-Plate (4/2 directional function), observe the following lower operating values:
pmin = 8 bar [116psi], qV > 3 l/min [0.8 USgpm].
RE 22045/05.08
M-.SED
Bosch Rexroth AG
Hydraulics
102,5 [4.04]
[1.28-0.0197]
65-0,5 [2.56-0.0197]
32,5-0,5
30 [1.18]
96,7 [3.81]
max. 6 [0.236]
15
15
[0.59]
[0.59]
6,4 [0.252]
11 [0.433]
83 [3.27] (79,5 [3.13])
2.1
2.2
69 [2.72]
11
7,5 [0.295]
45 [1.77]
F1
F2
B
TA
TB
F4
F3
6
For explanation of items, see 13.
Valve mounting screws (separate order)
4 hexagon socket head cap screws
ISO 4762 - M6 x 40 - 10.9-flZn-240h-L
Friction coefficient total = 0.09 to 0.14,
tightening torque MT = 12.5 Nm [9.2 ft-lbs] Nm 10%,
Material no. R913000058
Subplates to data sheet RE 45054
(separate order)
G 66/01 (G3/8)
G 67/01 (G1/2)
8,5 [0.33]
1.1
10
74 [2.91]
63+1 [2.48+0.0394]
[1.99] 50,5
12
0,01/100
[0.0004/4.0]
Rzmax 4
Required surface quality
of valve mounting face
9/14
10/14
Bosch Rexroth AG
M-.SED
Hydraulics
RE 22045/05.08
[0.59]
6,4 [0.252]
11 [0.433]
[0.79]
8,5 [0.33]
45 [1.77]
63+1 [2.48+0.0394]
B
TA
10
F2
A
TB
F4
F3
1.2
11
F1
2.2
69 [2.72]
7,5 [0.295]
50,5 [1.99]
20
2.1
G 66/01 (G3/8)
G 67/01 (G1/2)
96,7 [3.81]
max. 6 [0.236]
30 [1.18]
[1.28-0.0197]
65-0,5 [2.56-0.0197]
32,5-0,5
102,5 [4.04]
15
15
[0.59]
12
0,01/100
[0.0004/4.0]
Rzmax 4
Required surface quality
of valve mounting face
RE 22045/05.08
M-.SED
Bosch Rexroth AG
Hydraulics
102,5 [4.04]
[1.28-0.0197]
65-0,5 [2.56-0.0197]
48 [1.89]
12
6,4 [0.252]
11 [0.433]
[0.47]
1.1
9
32,5-0,5
30 [1.18]
96,7 [3.81]
max. 6 [0.236]
15
15
[0.59]
[0.59]
2.1
2.2
74 [2.91]
80 [3.15]
13
69 [2.72]
7,5 [0.295]
11
45 [1.77]
F1
F2
B
TA
TB
F4
63
10
8,5 [0.33]
50,5
+1 [2.48+0.0394]
[1.99]
F3
13
0,01/100
[0.0004/4.0]
Rzmax 4
Required surface quality
of valve mounting face
11/14
12/14
Bosch Rexroth AG
M-.SED
Hydraulics
RE 22045/05.08
[0.59]
96,7 [3.81]
max. 6 [0.236]
6,4 [0.252]
11 [0.433]
1.2
[0.47]
9
8
13
12
48 [1.89]
30 [1.18]
[1.28-0.0197]
65-0,5 [2.56-0.0197]
32,5-0,5
102,5 [4.04]
15
15
[0.59]
80 [3.15]
2.1
69 [2.72]
7,5 [0.295]
45 [1.77]
63+1 [2.48+0.0394]
B
TA
TB
F3
G 66/01 (G3/8)
G 67/01 (G1/2)
10
F2
F4
2.2
11
F1
50,5 [1.99]
20
8,5 [0.33]
[0.79]
13
0,01/100
[0.0004/4.0]
Rzmax 4
Required surface quality
of valve mounting face
RE 22045/05.08
M-.SED
Hydraulics
Bosch Rexroth AG
13/14
Attention!
On 3/2 directional poppet valves, ports B and TB
are provided as blind countersink.
On 4/2 directional poppet valves, port TB is provided as blind countersink.
Throttle insert
The use of a throttle insert is required when, due to the given operating conditions, flows can occur during the switching processes, which exceed the performance limit of the
valve.
Examples:
Accumulator operation,
14/14
Bosch Rexroth AG
Hydraulics
M-.SED
RE 22045/05.08
Notes
Bosch Rexroth AG
Hydraulics
Zum Eisengieer 1
97816 Lohr am Main, Germany
Phone +49 (0) 93 52 / 18-0
Fax
+49 (0) 93 52 / 18-23 58
documentation@boschrexroth.de
www.boschrexroth.de
This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It
may not be reproduced or given to third parties without its consent.
The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does
not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural
process of wear and aging.
RE 22045/05.08
M-.SED
Hydraulics
Bosch Rexroth AG
15/14
Notes
Bosch Rexroth AG
Hydraulics
Zum Eisengieer 1
97816 Lohr am Main, Germany
Phone +49 (0) 93 52 / 18-0
Fax
+49 (0) 93 52 / 18-23 58
documentation@boschrexroth.de
www.boschrexroth.de
This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It
may not be reproduced or given to third parties without its consent.
The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does
not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural
process of wear and aging.
16/14
Bosch Rexroth AG
Hydraulics
M-.SED
RE 22045/05.08
Notes
Bosch Rexroth AG
Hydraulics
Zum Eisengieer 1
97816 Lohr am Main, Germany
Phone +49 (0) 93 52 / 18-0
Fax
+49 (0) 93 52 / 18-23 58
documentation@boschrexroth.de
www.boschrexroth.de
This document, as well as the data, specifications and other information set forth in it, are the exclusive property of Bosch Rexroth AG. It
may not be reproduced or given to third parties without its consent.
The data specified above only serve to describe the product. No statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does
not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural
process of wear and aging.