Professional Documents
Culture Documents
c. Effectivity
d. Separability clause
12. Section 7 states that the Board is vested with the authority
to: Adopt an official __________ of the Board.
a. logo
c. Avatar
b. icon
d. Seal
13. The compensation and allowances of the Board is
comparable to that being received by the Chairman and
members of existing regulatory boards under the
Commission as provided for in the __________.
a. Civil Service
c. RA 1992
b. DBM
d. Gen Appropriations
Act
14. Each member of the Board shall take the/a __________ prior
to the assumption of office.
a. panel interview from the Appointment committee
b. board exam
c. proper oath
d. none of these
15. How much or what fine is required for any person who
shall violate any provision or any rules, regulations, the
Code of Ethics and the Code of Technical Standards of
Practice promulgated under RA 9292?
a. Not less than Php100,000.00 nor more than Php 1M
or by imprisonment of not less than 6 months nor
more than 6 year
b. Php100,000.00 to Php 1M or 6 yrs imprisonment or
both, in the discretion of the court
c. Not less than Php100,000.00 nor more than
Php 1M
or by imprisonment of not less than 6
months nor
more than 6 years, or both, in the discretion
of the
court
d. none of these
16. The Board and the __________ shall correct and rate the
licensure examination papers
a. Commission
c. IECEP
b. APO
d. none of these
17. According to section 2-Statement of Policy, the state shall
therefore develop and nurture competent, virtuous,
productive, and __________ PECE, ECE, and ECTs
a. God-fearing
c. versatile
b. religious
d. well-rounded
18. Within __________ years after the effectivity of RA 9292, the
Board shall issue Certificate of Registration and Professional
Identification Cards without examination to all applicants
for registration as Electronics Technicians who comply to all
the requirements stated in section 20.
a. 3 (three)
c. 7 (seven)
b. 5 (five)
d. none of these
19. With reference to prob 22, all submittals/documents shall
be accompanied by a certification from __________
registered PECEs vouching for the integrity, technical
capability and good moral character of the applicant.
a. at least 3
c. 5
b. 3
d. none of these
Vgy
t
P = work /time,
Substituting all values, we get for V
746W 8hx3600s / h
3
kg / m 3 9.8m / s 2 20m
1x10
1.1x10 2 m 3
V=
Since 1 m3 = 103 L, then V = 1.1 x 105L.
22. As provided in ACT 3846, the construction of a radio station
shall begin only when
a. A personnel of NTC has conveyed through
telephone that the application has already been
approved.
b. the firm applying for the construction permit has
submitted to the NTC its application for the same.
c. the technical documents has already been signed
and sealed by the PECE.
d. The NTC has already issued a Permit to
construct.
23. As provided in RA7925, a VAS provider needs to secure a
franchise if
a. it is offered by a telecommunications entity whose
proceeds of utility operations are not crosssubsidized.
b. it does not discriminate other service providers
against rates.
c. it is offered by a telecommunications entity that
uses a separate book of accounts for VAS.
d. it puts up its own network.
1 i
= F(P/F, i%, n)
P F
SOLUTION
F A
i
0.15
ieff 1
1 15.86%
4
b.P4,000
d. P6,000
SOLUTION
SOLUTION
X + Y 200
X + Y 400
X,Y0
b. Max Profit = PhP 10X +PhP 5Y
Subject to:
X + Y 200
4X + Y 400
X,Y0
SOLUTION
CO P53,000 P1,500 P54,500
C L P5,000
d
P54,500 P5,000
P3,668
F / A,6.5%,10
= (1500kg)(72km/hr)2 (1000m/km)2
(2)(1kg-m/N-sec2 )(3000 sec/hr)2
= 300,000 J or 300 kJ
= (5kg)(9.75m/sec2)(100m
(1kg-m/N-sec 2)
Fg = mg
k
= 5(9.75)
1
= 4875 J
= 48.75 N
H = mCpT = 1.36kg/s(1.0062kNm/kgK)(388.75-277.59K) =
152. kJ/s
F 27,000lb
lb
70. The proportional limit is the value of stress on the stressstrain diagram curve at which the curve first deviates from a
straight line.
a. Proportional limit
b. Elastic limit
c. Yield point
d. Tensile point
71. It is the value of stress on the stress-strain curve at which
the material has deformed plastically; that is, it will no longer
return to its original size and shape after removing the load.
a. Proportional limit
b. Elastic limit
c. Yield point
d. Tensile point
81. It is
a.
b.
c.
d.
82. It is
a.
b.
c.
d.
10,000 N
500MPa
20 x10 6 m 2
84. Assume that a 25-mm diameter rivet joins the plates that
are each 125 mm wide. The allowable stresses are 130 MPa for
bearing in the plate material and 65 MPa for shearing of the
rivet. Determine the minimum thickness of each plate.
a. 10MPa
b. 20MPa
c. 30MPa
d.
40Mpa
PL
AE
P ( 2m)
AE
0.8 10 3 m
0.95 10 3
P (3)
(40mm) 2 300G 4 [(52mm) 2 ( 40mm) 2 ]150G
P 160.57kN
P
dt
P
t
d b
31.91kPa
(25mm)130 M
t 9.82mm
t
V
2
4 d
65M
V
(25mm) 2
V P 31.91kN
88. A steel rod 3.5m long is secured between two walls. If the
load on the rod is zero at 30C, compute the stress when the
temperature drops to -30C. The cross sectional area of the rod
is 1200mm2, =11.7um/(mC), and E=200Gpa
a. 110MPa
b. 120MPa
c. 130MPa
d. 140Mpa
LT
PL
E
AE
TE (11.7 )(30 30)( 200G )
PL
LT
140.4 MPa
AE
T
P
A
31.91kNkN
[125mm 8mm 25mm 8mm]
39.89 MPa
D
2t
(450mm)
2(25mm)
16.67 MPa
150 MPa
12 x10 6
32
JG
13k (6)
4 x
4
180 (32d ) 85 x10 9
d 107.57 mm
c.
170mm
pD
4t
p (4 12in )
4(4 / 17in )
p 176.47 psi
FEU(GEAS THERMODYNAMICS)
9000
d.
175mm
Qconvection hA(Ts T f )
W
(1.2m 2 )(33 22)C
m 2 C
= 66W
=5
4
Qradiation (Ts4 Tsurr
)
= 0.95(5.67 x108
W
)(1.2m 2 )[(33 274)4 (22 273)4 ]K 4
m4 K 4
= 77.2W
Qtotal 66W 77.2W 143.2W 143.2 J / s
TL
(40 273) K
1
0.6415(64.15%)
TH
(600 273) K
Q 700kJ
kJ
1.75
T 400 K
K
W (110kPa)(0.8m 3 ) ln(
0.2
1kJ
)(
) 122kJ
0.8 1kPa m 3
105kPa(5 x6 x7 m 3 )
PV
256.1g
R ' T 0.287 m 3 kPa
( 27 273K )
/ kg K
Q H 92 MJs
Q L 45 MJs
QL
45
1
0.5109 (51.09%)
QH
92
Qlost Qgain
Qbrass Qwater
2lb (C )( 212 F 41.2 F ) 5lb (1
COP
C 0.091
Btu
)( 41.2 F 35F )
lb F
Btu
lb F
300kJ / min
1kW
(
) 1.67
3kW
60kJ / min
Q mct
Q 0.8kg(0.6
0.5m
kJ
(4.18
)(T2 25C ) 0
m3
kg C
0.001 kg
cal
)(78.3 15)C
g C
Q 30kcal
T2 25.6C
117. A rigid tank contains a hot fluid that is cooled while being
stirred by a paddle wheel. Initially, the internal energy of the
fluid is 850kJ. During the cooling process, the fluid loses 550kJ
of heat, and the paddle wheel does 200kJ of work on the fluid.
Determine the final energy of the fluid. Neglect the energy
stored in the paddle wheel.
a.500kJ
b. 550 kJ
c. 600kJ
d. 650 kJ
Q U W
200kJ (U 2 850kJ ) 550kJ
mT 1 mT
P
P
T 1 T
13.73
29.92
0.081x 273K 1 x 233K
lb
2 0.044 3
ft
U 2 500kJ
W nRT ln
V2
J
1 .5
3mol (8.317
)(320 K ) ln
9612.9 J 9.61kJ
V1
mol K
5
Q kAt
T
Btu
(9 2
L
ft hr
= 22,680 Btu
F
in
)( 2 ft 2 )( 24 hr )
300 90
4
F
in
TUP(GEAS PHYSICS)
124. Suppose that energy Q is required to accelerate a car
from rest to v, neglecting friction. How much added energy
would be required to increase the speed from v to 2v?
a.Q
b.2Q
c. 3Q
d.4Q
Using the energy equation W=KE2 KE1
Q = 0.5mv2 0 - condition 1
W = 0.5m(2v)2 0.5mv2 - condition 2
W=2mv2 0.5mv2 = 3(0.5mv2) = 3Q
125. Suppose you want to store 1.00 J of electric potential
energy in a volume of 1.00 m3 in vacuum. What is the
magnitude of the required electric field?
a. 0.475 MV/m
b. 0.336MV/m
c. 0.225TV/m
d. 0.113TV/m
u=1.00J/1.00m3 = 1.00J/m3
E=
2(1.00)
2u
=
o
o
a=60o
then
r =60o
r =a
, hence if
(c)
n=
633
=
=1.335
o 474
vr =
vr =
v a+ v b
v v
1+ a 2 b
c
0.900 c+ 0.700 c
=0.982c
( 0.9 ) ( 0.7 ) c 2
1+
c2
(d)
a. Torque
c. Axial forces
148. A steel rod 2.5 m long is secured between two walls. If the
load on the rod is zero at 20 degree Celsius, compute the
stress when the temperature drops to -20 degrees Celsius. The
cross-sectional are if the rod is 1200 sq. mm, coefficient of
linear expansion = 11.7 um/(m-deg.C), and E = 200 GPa.
Assume that the walls are rigid.
a. 69.3 MPa
b. 96.3 MPa
c. 93.6 MPa
d. 69.3 MPa
= (200x10^9)(11.7x10^-6)(20 - -20) = 93.6x10^6 Pa
= 93.6 MPa
149. Determine the maximum shearing stress in a helical steel
spring composed of 20 turns of 20 mm-diamter wire on a mean
radius of 80 mm when tha spring is supporting a load of 2 kN.
Use G = 83 GPa.
a. 110.6 MPa
b. 112.3 MPa
c. 120.6 MPa
d. 134.6 MPa
m = 80/10 = 8
= [16(2000)(0.08) / (0.02)^3]x{[4(8)-1]/[4(8)-4] +
(0.615/8)}
= 120.6 Mpa
150. Determine the elongation in a helical steel spring
composed of 20 turns of 20 mm-diamter wire on a mean radius
of 80 mm when tha spring is supporting a load of 2 kN. Use G
= 83 GPa.
a. 87.9 mm
b. 78.9 mm
c. 98.7 mm
d. 89.7
mm
= 64(2000)(0.08^3)(20) / [(83x10^9)(0.02^4)]
= 98.7 mm
151. These are components of the total resistance to sliding
the portion to one side of the exploratory section past the
other.
b. Bending moment
d. Shear forces
a.
Solid
b.
Gas
c.
Solid
d.
Gas
gas
solid
liquid
liquid
+
1
b.
c.
+
2
d.
c. Limiting principle
d. Uncertainty principle
O2
O2
at STP?
a. 1.2moles
b. 1.4moles
c. 2.0moles
d. 2.8moles
169. At STP, 1 mole will occupy 22.4L
170. The properties of solution include all of the following
except that
a. It is homogeneous mixture if it has been well stirred
b. Dissolved particles will settle out upon stirring
c. It is clear and transparent with particles too small to be seen
d. Dissolved particles will pass through a piece of filter paper