FINAL
Examination Paper
(COVER PAGE)
Session : September 2008
Programme : Diploma in Civil Engineering
Course EGC272 : Steel Design
Date of Examination 30" October, 2008
Time 11,00am till 1.00pm Reading Time : _Nil
Duration 2. Hours
Special Instructions
This paper consists of SIX (6) questions. Answer any FOUR (4) questions in the answer booklet |
provided. All questions carry equal marks.
Materials permitted
Non- programmable calculator
Materials provided
BS5950: Part 1: 1990, Section Tables and Deflection Formulae
Examiner(s) Engr. Cheah Beng Khoon
Moderator : Assoc Prof Dr Ir Abdul Khalim Abdul RashidINTI INTERNATIONAL UNIVERSITY COLL
DIPLOMA IN CIVIL ENGINEERING PROGRA\
EGC272 : STEEL DESIGN
EGC272(F) / Page 1 of 6
EGE,
MMB
FINAL EXAMINATION : SEPTEMBER 2008 SESSION
This paper consists of SIX (6) questions. Answer any FOUR (4) questions in the answer
booklet provided. All questions carry equal marks. All steel sei
and bolts are Grade 4.6 to BS 4190. Welds are to BS 5135
Is
el
dimensions are in millimetres unless otherwise stated,
Question 1
are Grade 43 to BS 4360
‘lectrodes to BS 639. All
For the inverted ‘fee’ section shown in Figure QI below, determine the following sectional
properties ..
(a) centroidal (x-x ) axis
(6) equal area (x-x ) axis
(c) second moment of area about the °x-x" axis
(4) second moment of area about the ‘y-y" axis
(ec) radius of gyration about the x-x axis
(0) elastic modulus about the x-x axis top and bottom
() plastic modulus about the x-x axis
300
Figure Qi
(marks)
(2 marks)
(4 marks)
(4 marks)
G marks)
(4 marks)
(6 marks)EGC272(F) / Page 2 of 6
ion 2
(@) Provide sket
of bridge tru
to illustrate the differei
ween a Parker, a Pratt and a Petit type
(3 marks)
(b) Ignoring the self weight of all members in the pin jointed truss shown in Figure Q2(b)
below, determine whether a 250x250L104 is suitable for use as member ‘e-g* when
subjected to the given loads at the nodes. Consider all connections as welded.
(22 marks)
4000 |, #000 4000
Figure Q2(b)
|. 3000
3000°272(F) / Page 3 of 6
Question 3
(2) What is a castellated beam, a compound beam and a crane beam? Use sketches to
illustrate your answer
G marks)
(b) Check if'a fully restrained 457x152UB60 is satisfactory in BENDING, SHEAR and
DEFLECTION when used as beam ‘8/J-K” in Figure Q3(b) below.
(22 marks)
live load = 6 kNA>
all clebs = 2OOmm thick , Bs 24 kny*
oN beams = 457x1S2UB60
Sire protectun = O-2 kaif Of beam
{rey
OX I ; 1:
/
t
a
3 : '
9o \ \
S
d
\
t
( !
J t
@v.—1 T a I erent et
\ \
\ ’
\
} !
eee rey ;
o ‘ (
: \
5000 S000
é 4 4
@ Figme 36) @ PLAN Cuts.) @EGC272(F) / Page 4 of 6
Question 4
(2) What is the mein structural difference betw
nd slender cola
(2 marks)
(6) Can a 203x203UC46 be used for ground floor column ‘K/8? of the double storey
building shown in Figure Q3(b) previously? The elevation of this building is shown in
Figure Q4(b) below. The given live load applies at every level.
(23 marks)
Slat
roof
| pisced live loed = 6 ENA,
5 aN claks = 200mm» tlk
3 Boone 2 DA krYa®
2
| fist — Sie proofing Fur beeme
Sees FO ancl ‘Colamad = O-2 bag
all beams 46e
| 457x152 uk60
3| all columar ere
in 20? x 207 UC46
|
ground
Sited | Flooe
a TAN
SECTION K-% CNS)
Figure Q4(b)BGC272(F) / Page 5 of 6
Question
(2) What are the 2 main types of bolts?
(2 marks)
(b) Is the bolted double angle “tee” connection shown in Figure Q5(b) below capable of
supporting a tensile dead load of 222KN plus a tensile live load of 333KN?
(23 marks)
both eagles
ISox7S JL 24-8
all beHs = MzO
cover plete.
55ux 1G0%12 thk
splice plete
SSURISS X10 4ok Pee
SECTION CN-TS:)
ELEVATION Cure.)
Figure Q5(b)EGC272(F) / Page 6 of 6
Question 6
(@) — What are the 2 main types of welds?
(2 marks)
{b) Design the welded bracket connection shown in Figure Q6(b) below based on the
assumption that rotation occurs first about the ‘x/-x/’ and then about the ‘x2-x2’ axis,
State which design method gives the more economical solution.
(23 marks)
“i E px!
| 2 3
- ae
i 127x716 UB 13” ,
71S 2K 1S2UCIB--~
FRONT view RIGHT VIEW
CNcTS.) CNTs.)
Figure Q6(b)
- THE END
£GC292(F)'Cheah Beng Koen 100908 povns