Professional Documents
Culture Documents
Abstract
Well testing operations are an essential component in reservoir characterization process. In deepwater
environments where rig costs are high, operating safely and cost efficiently is important. As a result, many
operators are constantly searching for more efficient and cost effective ways to test their reservoirs. The
use of newly developed tools and technologies is necessary to deal with the challenges of efficiency and
effectiveness while at the same time, safely optimizing the operational sequences, improving decision
making with real-time information and reducing rig costs, without sacrificing data quality.
Designed specifically for testing operations, the single trip downhole tools with real-time bottomhole
data enabled by wireless acoustic telemetry address those challenges. This technology eliminates unnecessary trips compared with a conventional drillstem test (DST) in deepwater environments. Furthermore,
real-time bottomhole data aid processes such as test design optimization and real-time well test interpretation and help to ensure that data are sufficient for the purpose of reservoir characterization prior to
ending the test.
This paper summarizes the benefits of using the new generation of downhole reservoir testing tools.
These tools were used in deepwater environments in West Africa and Brazil. The well testing operation
was performed in a single trip, saving 3 days of rig time compared with the time required for a traditional
DST with a permanent packer. Data acquired during the test were transmitted to secure servers, and were
available in real-time for remotely located decision makers. The improved communication and collaboration between offshore and office, resulted in a short decision-making time cycle. The team performed
pressure transient analysis on downhole data during the well test, turning the raw data into knowledge.
This helped to confirm that sufficient data had been acquired for reservoir characterization; thus, the test
duration was shortened while still meeting all test objectives. In summary, the operator was able to
perform a safe and cost-effective well test operation in a deepwater environment.
Introduction
Before initiating the development of oil and gas fields, the operator evaluates the project economics.
During the initial exploration and appraisal stages a large quantity of information is collected to reduce
uncertainties and determine if the hydrocarbon field is a strong financial undertaking. During the drilling
phase and until the end of well testing operations, operators are seeking best practices and efficient
technologies to help guarantee safe operations and economical viability of the project.
SPE-176782-MS
Well testing is an important operation, which has a significant impact on the project economics. During
a well test, temporary completions or drillstem test (DST) tools are used in an attempt to flow the well
to the surface. At the surface, various types of equipment are used to control, measure, sample and finally
dispose of the fluids. The information gathered during a DST is essential for reservoir characterization and
the determination of permeability, skin, and subseismic boundaries. Following reservoir characterization,
well deliverability will be identified and a production and completion strategy will be selected for
development wells.
Downhole tools used for well testing consist of four main components: a packer, a downhole dual valve
(tester and circulating valves), pressure and temperature recorders and a fluid sampler. The packer isolates
the formation, the tester valve opens and closes the well downhole, and the fluid sampler obtains clean
and representative reservoir fluid samples, downhole gauges records pressures and temperatures. There
are numerous additional tools for safety and other operational needs. DST tool components have been
developed to ensure safe operations, acquire accurate data and perform cost-effective tests.
SPE-176782-MS
SPE-176782-MS
SPE-176782-MS
pressure and temperature at the same point in the crystal. This unique feature dramatically reduces thermal
effects and provides the most accurate pressure measurements available. The fourth component is an
inline independent reservoir fluid sampling tool (Sooklal et al, 2014; Ratchinsky et al, 2014).
Figure 2From left to right, isolation system (packer body and seal assembly), downhole dual valve, quartz gauges and donwhole
inline fluid sampler
The backbone of these downhole tools is a wireless acoustic telemetry system, which is a network of
repeaters clamped onto the tubing (Fig. A3, Appendix A), which uses an acoustic wave generated in the
pipe (tubing) to transmit the information. Each repeater can transmit or receive an acoustic signal (Fig.
A4, Fig. A5, Appendix A). The digital information is acoustically conveyed from one repeater to another
both up or downhole. In the bottomhole assembly, the network interfaces with either downhole pressure
gauges for real-time bottomhole data acquisition or with downhole tools, such as a tester valve, circulating
valve, firing head or fluid sampler to issue command and verify tool status. The systems modular design
provides the operator with flexibility when choosing features to enable via the wireless telemetry. For
example, the operator can enable gauges and sampler wirelessly but operate the dual valve by a pressure
pulse. All of the tools are equipped with conventional backup control.
These advanced downhole tools resolve many of the challenges associated with traditional DST tools.
The isolation system acts like a permanent packer in deepwater environment, but only requires a single
trip; eliminating unnecessary trips. The wireless telemetry acquires downhole pressure and temperature in
real-time allowing for real-time well test interpretation and optimizing the flow duration and build-up
periods during a test. Compared with conventional pressure activated samplers, wirelessly activated
sampling has several advantages. First, wireless sampling is not limited by pressure window requirements
for rupture discs; therefore, adding flexibility on the number of samples to be captured. Second, when
samplers have been fired and the reservoir fluid has been captured, confirmation is sent by acoustic signal
to the surface, a feature not available using previous sampling technology. Third, the use of wireless
telemetry can help to confirm whether the tester or circulating valves have operated correctly by checking
the downhole pressure above and below the valves. Prior to the development of wireless telemetry, it was
necessary to run wireline or coil tubing to verify whether downhole valves were open or closed.
SPE-176782-MS
The single trip downhole tools enabled by wireless telemetry was selected, as the most efficient way
of testing in a deepwater environment. The modular design facilitated the selection of downhole gauges
enabled by wireless telemetry to provide real-time downhole data. The other downhole components were
to be pressure activated.
The well test was perforated underbalanced, after which an initial flow period and shut-in were
performed to identify initial reservoir pressure. Following this operation, a well cleanup was carried out
to remove the drilling induced damage and the well was shut-in to identify preliminary permeability, skin
and reservoir pressures using pressure transient analysis. Finally, a main flow period on several choke
sizes was performed to estimate inflow performance and confirm pressure transient analysis results during
a main buildup period. Reservoir fluid samples were taken during a sampling flow period and the
maximum flow rate was measured at a later time during the test.
Data acquired during the test were transmitted to secure servers, and made available in real-time for
remotely located decision makers (Fig. A6, Appendix A). Real-time collaborative testing platform
software was used for graphical visualization, providing an integrated view of surface and downhole data
to the support team. This software improved communication and collaboration between offshore and
office, resulting in a short time cycle for decision making. The downhole quartz gauges enabled by
wireless telemetry transmitted data successfully throughout the test duration. The real-time availability of
bottomhole pressure data enabled real-time verification that the underbalance condition before perforation
was correct and confirmed that perforation had been achieved successfully (Fig. A7, Appendix A).
Furthermore, whenever downhole tools were operated, it was possible to confirm whether the tools had
been activated successfully by monitoring downhole pressures (Fig. A8, Appendix A). The productivity
index could also be monitored in real-time (Fig. A9, Appendix A). The downhole data during buildup
periods, was used to conduct pressure transient analysis. During the shut-in after the cleanup flow period,
in less than 10 hours it was already clear that derivative achieved infinite acting radial flow (Fig. 3).
Turning raw data into knowledge during the test allowed for optimizing the well test design in real-time.
The planned 48 hours for final buildup was not necessary and buildup time was reduced, while achieving
the same results for well test interpretation. The total time for the well test was shortened by 28 hours,
without sacrificing data quality (Table 2). When the test was completed and the downhole quartz gauges
Table 2The planned test design versus actual test optimized during well test
were retrieved to the surface, memory data from the quartz gauge were compared with the real-time data,
which had been used for interpretation during the test. A comparison of log-log plots was used to optimize
the durations of buildup times for both sets of data showed a good quality match between the real-time
and the retrieved memory data, validating the decisions made during the operation (Fig. 3).
SPE-176782-MS
Figure 3Log-log plot. Green is the memory data, red is the real-time data
Conclusion
Since the early days of DST operations, development of downhole tools has been optimized to make well
testing operations safer and more efficient and to acquire accurate data for reservoir characterization.
There have been several major milestones in the development history of downhole tools. The mechanically activated tools were improved by introduction of pressure activated tools, after which low pressure
pulse activated tools became the industry standard for DST operations. Currently, the major breakthrough
in the development of DST tools is wireless acoustic telemetry enabled tools.
The new generation of downhole tools operated by wireless acoustic telemetry allows for the isolation,
control, measurement and sampling of a reservoir fluid during a single trip and also provides real-time
bottomhole data. The wireless telemetry allows for transmitting real-time bottomhole data to members of
the operators reservoir engineering team, allowing the team to perform pressure transient analysis on
downhole data during the well test. The reservoir engineers in various locations were able to collaboratively make decisions, manage wellbore events, and refine the test sequence in real-time.
These advanced downhole tools have proved to be an efficient method for performing DST. Using
these acoustically enabled tools, it was possible to achieve the following:
Data transmitted by the acoustic wireless telemetry system brought light to reservoir features during the
well testing operation and ensured all necessary data were acquired to perform a successful test before
pulling the DST string out of the hole.
The use of single trip downhole tools allowed eliminating unnecessary trips. In addition, the availability of real-time bottomhole data enabled the test duration to be optimized, while ensuring all testing
objectives were met.
Acknowledgement
The authors wish to thank the Schlumberger well testing team and especially Marcelo Gandra Braz,
Ifeanyi Nwagbogu, Vladimir Konovalov, Pramod Kumar, Stephane Vannuffelen for their great contribution and support in the publication.
SPE-176782-MS
References:
McLeod, C., Mitchell, S., Guimard, A. et alet al. 1979. Surface Read-Out of DST Data in Real Time.
Presented at the 11th Annual Offshore Technology Conference, Houston, Texas, 30 April 30 3
May. OTC 3458.
Maizeret P.D, Keidel C., Nwagbogu I. et alet al. 2014. A Step Change in Deepwater Test Operations
with Downhole Wireless Telemetry. Presented at IADC/SPE Drilling Conference and Exhibition,
Fort Worth, Texas, USA, 4 6 March. IADC/SPE 167996.
Sooklal A., Walden C., Ennaifer A. et alet al. 2014. Step Change in Well Testing Operations. Oilfield
Review (Autumn): 3241
Ratchinsky M. Sooklal A., Walden C. et alet al. 2014. Wireless-enabled downhole tools aid deepwater
well test. E&P (4): 76 79.
SPE-176782-MS
Appendix A
10
SPE-176782-MS
SPE-176782-MS
11
12
SPE-176782-MS
Figure A4 The network of repeaters. Two repeators installed in each node supply horizontal redundancy (one is always on stand-by).
The vertical redundancy is provided by repeaters able to communicate twice the normal spacing between repeaters.
SPE-176782-MS
13
Figure A6 Real-time data transmission from the rig to remote server using global connectivity, collaboration, and information service.
Real-time collaborative testing platform software enables performing pressure transient analysis using Kappa, nodal analysis using
steady-state multiphase flow simulator to check pressure/volume/temperature properties of the fluid against the equation of state
using the PVTi industry-reference reservoir simulator
Figure A7Downhole pressure is underbalanced before perforation and clear indication of perforation could be observed