Professional Documents
Culture Documents
Revision Record
Refer to the portion indicated by change bar in each section.
Also refer to the reasons in table below.
Version
Issue date
Note
Version 0.9
Version 1.0
Table of Contents
6.1 CE Mode Overview.....................................................................................................6-1
6.1.1 Functions of the Control Panel in the CE Mode.............................................................................. 6-1
6.1.2 How To Enter the CE Mode ............................................................................................................ 6-2
6.1.3 Overview of the CE Mode Operation .............................................................................................. 6-2
6.1.4 How to Exit the CE Mode................................................................................................................ 6-3
6.1.5 Menu Tree....................................................................................................................................... 6-4
6.1.6 CE Mode Functions Overview ........................................................................................................ 6-8
6.9 Information................................................................................................................6-52
6.9.1 Scan Counter ................................................................................................................................ 6-52
After entering the CE mode, use the buttons displayed on the touch panel and messages in the display for
operation.
[ ]:
Moves upward one by one. Pressing this at the top of the list will return to the bottom.
[ ]:
Moves downward one by one. Pressing this at the bottom of the list will return to the top.
[ ]:
Moves the cursor to the left by one.
[ ]:
Moves the cursor to the right by one.
[OK] button :
Press the [OK] button to confirm the selection or execute the processing.
[<--] (Back) button :
Press the [<--] (Back) button to cancel the selection or stop the processing.
Gyrfalcon Service Manual Version 1.0
6-1
Hold down the [4], [5], and [6] buttons and turn on the power of the printer.
Diag Password.
Press the [2] button twice, and then press the [5] button once.
CE Mode
* Printer Diag
FAX/Scanner Diag
Please wait.
To execute the diagnosis for other items, press the [<--] (Back) button until the screen returns to the item to
evaluate.
If any error occurs while in the diagnosis or in the middle of selecting parameter values, an error message will
appear and the processing will stop.
To cancel the error message and return to the menu screen, press the [<--] (Back) button or the [OK] button.
6-2
Return to the top level of Printer Diag or Fax/Scanner Diag, and use the [ ] or [ ] button until
the [Complete] appears, and then press the [OK] button.
(e.g.: To exit the CE mode from Printer Diag, display the message below.)
Printer Diag
Complete
Complete
Complete
Complete
Complete?
Press the [OK] button again, and the printer will exit the CE mode and re-start (same as the
power on).
6-3
3ULQWHU'LDJ
$OO7HVW
(66'LDJ
)ODVK5207HVW
((35207HVW
'5$07HVW
0$&3+<7HVW
$6,&7HVW
,277HVW
86%+RVW7HVW
57&7HVW
7(670RGH
6LQJOH6WHS
*HW'HYLFH,QIR
H00&7HVW
1)&7HVW
,27'LDJ
'LJLWDO,QSXW
'LJLWDO2XWSXW
1906HWWLQJV
526([SRVXUH
190(GLW
6DYH190WR(66
/RDG190IURP(66
'HZ3UHYHQWLRQ
$7&0RGH
3ULQW,QIR
&RQILJ3DJH
3ULQW6HWWLQJV
,QVWDOODWLRQ6HW
6HUYLFH7DJ
6HULDO1R
+H['XPS
7RQH&RUUHFWLRQ
3L[HO&RXQWHU
&RQILJXUDWLRQ
'LS6ZLWFK
'LS6ZLWFK
'LS6ZLWFK
'LS6ZLWFK
3ULQW&RXQWHU
3ULQW6HUYLFH
&RS\6HUYLFH
)$;6HUYLFH
6FDQ6HUYLFH
&RXQWHU&RS\0WR%
&RXQWHU&RS\%WR0
7KLVLWHPLVGLVSOD\HGRQO\ZKHQWKH
190EDFNXSGDWDKDVEHHQVWRUHGE\
H[HFXWLQJ>6DYH190WR(66@
=D$.$
6-4
190,QLW
-2%/2*,QLW
'HYLFH'DWD,QLW
1)&5)0RGH
7HVW3ULQW
7HVW3DW>,27@
*UDGDWLRQ
3DUDPHWHU
5HJL
/LIH
6ORZ6FDQ.WR3
)DVW6FDQ6PS03)
)DVW6FDQ6PS7UD\
)DVW6FDQ6PS7UD\
)DVW6FDQ'XS03)
)DVW6FDQ'XS7UD\
)DVW6FDQ'XS7UD\
)XVLQJ39
)XVLQJ+HDWWLPH
7UDQV8QLW39
'UXP39
'UXP7KLFNQHVV
:DVWH)XOO&RXQW
7RQHU'LVS7LPH
7RQHU3L[HO
7RQHU*DV*DXJH
3ULQW
&RPSOHWH
7KLVLWHPLVGLVSOD\HGRQO\ZKHQWKHRSWLRQDOWUD\LVLQVWDOOHG
=D$.$
6-5
)D[6FDQQHU'LDJ
$OO7HVW
%RDUG7HVW
)D[0HPRU\7HVW
)D[)ODVK:57HVW
05$0:57HVW
,)7HVW
)D[&DUG,)7HVW
$)(6HULDO,)7HVW
,,7,)7HVW
$6,&7HVW
$6,&,-$&7HVW
$6,&-%,*7HVW
5HOD\6LJQDO7HVW
5HOD\7HVW
+RRN7HVW
6LQJOH7RQH6HQG
'70)6HQG
'LDO3XOVH6HQG
5LQJ%DFN7RQH
'DWD6HQG
/LQH9ROWDJH
/LQH&XUUHQW
,QIRUPDWLRQ
6FDQ&RXQWHU
6FDQQHU0DLQWHQDQFH
:KLWH%DODQFH
$XWR$GMXVW)%
$XWR$GMXVW'$')
6KDGLQJ3DUDPHWHU
&RHII)%5('
&RHII)%*5((1
&RHII)%%/8(
&RHII)%*5$<
&RHII'$')5('
&RHII'$')*5((1
&RHII'$')%/8(
&RHII'$')*5$<
7DUJHW5('
7DUJHW*5((1
7DUJHW%/8(
7DUJHW*5$<
5HJLVWUDWLRQ3DUDP
5HJL)%/HDG
5HJL)%6LGH
5HJL'$')/HDG)URQW
5HJL'$')6LGH)URQW
5HJL'$')/HDG%DFN
5HJL'$')6LGH%DFN
5HJL'$')/HDG)URQW'XS
$XWR5HJLVWUDWLRQ
6HQVRU3DUDPHWHU
6-6
=D$.$
9HUWLFDO6FDQ0DJ
7HVW3DWWHUQ
0DJ)%&2/25
0DJ)%*5$<
0DJ'$')&2/25
0DJ'$')*5$<
3DWWHUQ1R
,,7,2&KHFN
+RPH3RV6HQVRU
7UD\6HQVRU
)HHG6HQVRU
'$')&RYHU6HQVRU
'$'))HHG6HQVRU
)%&RYHU6HQVRU
/DPS
)%0RWRU
'$')0RWRU
'$')6ROHQRLG
6FDQ&RXQWHU&OHDU
&RXQWHU&OHDU)%
&RXQWHU&OHDU'$')
&DUULDJH'ULYHB
3DUDPHWHU
$OO&OHDU
%DFN8S'DWD
8VHU&OHDU
6\VWHP&OHDU
8VHU 6\VWHP&OHDU
6\VWHP'DWD,QLW
'RFXPHQW&OHDU
&RPSOHWH
=D$.$
6-7
ESS Diag
Description
See
All Test
6.2.1
FlashROM Test
6.2.2
EEPROM Test
6.2.3
DRAM Test
6.2.4
MAC+PHY Test
6.2.5
ASIC Test
6.2.6
IOT Test
6.2.7
6.2.8
RTC Test
6.2.9
eMMC Test
6.2.10
NFC Test
6.2.11
Digital Input
6.3.1
Digital Output
6.3.2
NVM Edit
IOT Diag
Print Info
SaveNVM to
NVM
ESS
Settings
LoadNVM from
ESS
6.3.3
Loads all the NVM information in the ESS NVM into the
IOT.
ROS Exposure
6.3.4
Dew Prevention
6.3.5
ATC Mode
Sets whether to enable the ATC (Automatic Toner Control) empty detection mode.
6.3.6
Config Page
6.4.1
Print Settings
6.4.2
6-8
Installation Set
Service Tag
Serial No.
HexDump
Tone Correction
(IOT tone correction)
Pixel Counter
Configuration
Print
Counter
Print Service
Copy Service
FAX Service
Scan Service
Complete
See
6.5
Counter Copy M to B
Counter Copy B to M
NVM Init
Initializes NVM.
NFC RF Mode
Gradation
Prints the pattern containing patches of different densities ranging from 0 through 100%. (ESS built-in test pattern)
Regi
6.7.1
Life
6.7.2
6.7.3
Complete
6.1.4
Test Print
Parameter
Description
6-9
6.6
All Test
Fax
Memory Test
SRAM W/R
Test
6.8.1
6.8.2
6.8.3
ASIC Test
6.8.4
Relay/
Signal
Test
Relay Test
Hook Test
Single Tone
Send
DTMF Send
Dial Pulse
Send
Ring Back
Tone
Data Send
Specifies the speed and pattern for checking data forwarding (no pattern for V.34)
Line Voltage
Line Current
Parameter
See
I/F Test
Board Test
(Board
Diag)
Scanner
Maintenance
Description
6.8.5
6.9.1
White Balance
6.10.1
Shading Parameter
6.10.2
Registration Param.
6.10.3
Auto Registration
6.10.4
Sensor Parameter
6.10.5
6.10.6
Test Pattern
6.10.7
6.10.8
6.10.9
Carriage Drive_100
6.10.10
6-10
6.11
Backup
Data
Complete
Description
All Clear
User Clear
Sysytem Clear
User&Sysytem Clear
Document Clear
Complete
6-11
See
6.12
6.1.4
Error
CHECK OK
*** Error
Note
***: Displays the name of the test ended in error.
(Flash ROM / EEPROM / DRAM / ASIC / IOT)
Procedure
1
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
CE Mode
* Printer Diag
FAX/Scanner Diag
Printer Diag
ESS Diag
Printer Diag
ESS Diag
ESS Diag
All Test
All Test
Start
6-12
All Test
Processing
All Test
CHECK OK
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
ESS Diag
Error
CHECK OK
Error
CHECK OK
6-13
Error
CHECK OK
Error
CHECK OK
MAC+PHY ERROR
Error
CHECK OK
ASIC CHECK NG
6-14
Error
CHECK OK
IOT ERROR
TEST MODE
Description
TEST J
TEST K
TEST SE0
Keeps SE0 state for the DownStream port of the Host Controller.
TEST PACKET
Repeatedly sends the test packet form the DownStream port of the
Host Controller.
TEST ENABLE
NOTE
To complete the test mode, restart the printer.
6-15
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Printer Diag
ESS Diag
ESS Diag
All Test
Use the [ ] button to select [USB Host Test], and press the [OK] button.
ESS Diag
USB Host Test
Use the [ ] button to select [Single Step], and press the [OK] button.
Single Step
Address: 000
Single Step
Address: 002
Cursor
7
Single Step
DATA IN
Single Step
Address: 002
Press the [OK] button to obtain data from the device specified.
6-16
Single Step
CHECK OK
10
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
ESS Diag
11
6-17
Error
CHECK OK
RTC ERROR
Error
CHECK OK
eMMC ERROR
Error
CHECK OK
NFC ERROR
6-18
Link
Component
010
200
010
201
010
202
041
300
041
301
042
200
042
201
071
100
071
101
071
102
Regi Sensor
071
103
Exit Sensor
071
116
071
200
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [IOT Diag], and press the [OK] button.
Printer Diag
IOT Diag
IOT Diag
Digital Input
6-19
IOT Diag
Digital Input
Digital Input
010 - 200
OFF
Digital Input
041-300
OFF
Digital Input
041-300 L 00
Open and shut the front cover to check that the display changes as shown below.
Cover Open
Cover Close
Digital Input
041-300 H 00
Digital Input
041-300 L 01
Digital Input
041-300
OFF
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
IOT Diag
10
6-20
NOTE
Except for 010-001, 042-001, 042-002, and 042-003, set LVPS 24V (041-001) to ON (EXEC). Otherwise,
the component does not operate.
Link
010
001
Fusing Relay
041
001
042
001
042
002
042
003
LVPS Fan
061
001
071
001
071
002
071
003
071
004
071
005
071
006
Regi Clutch
071
007
071
008
071
009
071
010
071
011
071
018
093
001
093
002
Component
6-21
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [IOT Diag], and press the [OK] button.
Printer Diag
IOT Diag
IOT Diag
Digital Input
Use the [ ] button to select [Digital Output], and press the [OK] button.
IOT Diag
Digital Output
Digital Output
010-001 READY
To set LVPS 24V to On, use the [ ] or [ ] button and select [041-001].
Digital Output
041-001 READY
Digital Output
041-001 EXEC
To carry on checking the operation of Main Motor (Half), do not press the [<--] (Back) button. Use
the [ ] or [ ] button to display [071-002].
Digital Output
071-002 EXEC
Digital Output
071-002 EXEC
6-22
To carry on checking the operation of Regi Clutch, do not press the [<--] (Back) button. Use the
[ ] or [ ] button to display [071-010].
Digital Output
071-006 READY
10
Digital Output
071-006 EXEC
11
Press the [<--] (Back) button to stop the Regi Clutch operation.
Digital Output
071-006 READY
12
To stop the Main Motor (Half) operation, use the [ ] button to select [071-002], and then press
the [<--] (Back) button.
Digital Output
071-002 READY
13
To set LVPS 24V to Off, use the [ ] button and select [041-001], and then press the [<--] (Back)
button.
Digital Output
041-001 READY
14
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
IOT Diag
15
6-23
742
746
746
746
746
Link
516
020
NVM Name
Toner discharge
mode switch
021
Electrostatic
memory action
mode switch
022
Pre-exposure
mode
026
ATC empty
detection switch
Range
0, 1
0, 1
0, 1
0, 1
0, 1
Default
Value
Description
6-24
NVM Read and Write (NVM Edit) is for changing settings peculiar to the device, and therefore requires
you a precise attention, otherwise you might lose the essential setting of the printer or give the printer an
unrecoverable failure.
Procedure
1
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [IOT Diag], and press the [OK] button.
Printer Diag
IOT Diag
IOT Diag
Digital Input
Use the [ ] button to select [NVM Settings], and press the [OK] button.
IOT Diag
NVM Settings
NVM Settings
NVM Edit
Cursor
7
6-25
742-516
+00000000001*
008-002
Number NG
742-516
+00000000011*
Cursor
Press the [OK] button to start writing the new NVM value.
742-516
+0000000001
10
NVM Edit
Please Wait
11
NVM Settings
NVM Edit
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
IOT Diag
12
6-26
NOTE
If the IOT NVM information has never been changed using [Edit NVM}, [Save NVM to ESS] cannot be executed.
Procedure
1
Enter the CE mode to select [IOT Diag] > [NVM Settings], and press the [OK] button.
(See "6.1.2 How To Enter the CE Mode".)
IOT Diag
NVM Settings
NVM Settings
NVM Edit
Use the [ ] button to select [SaveNVM to ESS], and press the [OK] button.
NVM Settings
SaveNVM to ESS
SaveNVM to ESS
OK?
SaveNVM to ESS
Processing
SaveNVM to ESS
Saved
Press the [<--] (Back) button to return to the [Printer Diag] screen, and then exit the CE mode.
(See "6.1.4 How to Exit the CE Mode".)
6-27
Do not execute "NVM Loading" unless "NVM Saving" has been executed. Doing so will damage PWBA
MCU.
Procedure
1
Enter the CE mode to select [IOT Diag] > [NVM Settings], and press the [OK] button.
(See "6.1.2 How To Enter the CE Mode".)
IOT Diag
NVM Settings
NVM Settings
NVM Edit
Use the [ ] button to select [Initialize Slave], and press the [OK] button.
NVM Settings
LoadNVM from ESS
Press the [<--] (Back) button to return to the [Printer Diag] screen, and then exit the CE mode.
(See "6.1.4 How to Exit the CE Mode".)
6-28
Confirm that the [Printer Diag] is selected, and press the [OK] button.
Use the [ ] button to select [IOT Diag], and press the [OK] button.
Printer Diag
IOT Diag
IOT Diag
Digital Input
Use the [ ] button to select [ROS Exposure], and press the [OK] button.
IOT Diag
ROS Exposure
ROS Exposure
Auto Correct
Auto Correct
OK?
Auto Correct
Processing
Auto Correct
Corrected
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
IOT Diag
6-29
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [IOT Diag], and press the [OK] button.
Printer Diag
IOT Diag
IOT Diag
Digital Input
Use the [ ] button to select [Dew Prevention], and press the [OK] button.
IOT Diag
Dew Prevention
Dew Prevention
OFF *
Use the [ ] or [ ] button to switch to ON or OFF, and press the [OK] button.
Dew Prevention
ON
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
IOT Diag
6-30
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [IOT Diag], and press the [OK] button.
Printer Diag
IOT Diag
IOT Diag
Digital Input
Use the [ ] button to select [ATC Mode], and press the [OK] button.
IOT Diag
ATC Mode
ATC Mode
OFF*
Use the [ ] or [ ] button change the ON/OFF setting, and press the [OK] button for confirmation.
ATC Mode
ON
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
IOT Diag
6-31
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [Print Info], and press the [OK] button.
Printer Diag
Print Info
Print Info
Config Page
Print Info
Config Page
Config Page
Ready
Config Page
Processing
Config Page
Ready
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
Print Info
6-32
6-33
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [Print Info], and then select the [OK] button.
Printer Diag
Print Info
Print Info
Config Page
Use the [ ] button to select [Print Settings], and press the [OK] button.
Print Info
Print Settings
Print Settings
Ready
Print Settings
Processing
Print Settings
Ready
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
Print Info
6-34
Range
Description
Service Tag
7 digits
Serial No.
9 digits
HexDump
ON,OFF
ON,OFF
0-100%
Pixel Counter
Dip Switch 0
Configuration
Dip Switch 1
B/W
B/W print counter
B/W Backup
Backup B/W print counter
B/W Error
B/W print error counter
Displays the number of auto-recoveries performed when the value of the B/W print
counter is different from that of the Backup B/
W print counter.
B/W
B/W copy counter
B/W Backup
Backup B/W copy counter
Displays the number of auto-recoveries performed when the value of the B/W copy
counter is different from that of the Backup B/
W copy counter.
Dip Switch 2
Dip Switch 3
Print Counter
(Print Service)
Print Counter
(Copy Service)
B/W Error
B/W copy error counter
6-35
Range
Description
B/W
Monochrome fax reception
counter
B/W Backup
Monochrome fax reception counter backup
B/W Error
Monochrome fax reception
error counter
Displays the number of auto-recoveries performed when the number of the FAX received
is different from the count backup.
SMB/FTP
SMB/FTP counter
Email
Email counter
SMB/FTP Backup
SMB/FTP counter backup
Email Backup
Email counter backup
SMB/FTP Error
SMB/FTP error counter
Displays the number of auto-recoveries performed when the number of SMB/FTP count is
different from the count backup.
Email Error
Email error counter
Displays the number of auto-recoveries performed when the number of E-mail count is
different from the count backup.
Counter Copy B to M
NVM Init
Initializes NVM
(ESS NVM all delete ( = 0 clear))
Print Counter
(FAX Service)
Print Counter
(Scan Service)
Counter Copy M to B
6-36
Range
Description
Error Log
Jam Log
Job Log
FW Parameter
NET Parameter
Auditron/PV
MRAM Adrs
FAX Log
eMMC
Erase Complete
Normal-end.
NFC RF Mode
ON,OFF
6-37
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [Installation Set], and press the [OK] button.
Printer Diag
Installation Set
Installation Set
Service Tag
Use the [ ] button to select [SerialNo.], and press the [OK] button.
Installation Set
SerialNo.
Serial No.
000000000 *
Serial No.
000000000 *
Serial No.
000000001
Cursor
Installation Set
SerialNo.
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
Installation Set
6-38
Confirm that [Printer Diag] is selected, and press the [OK] button.
Use the [ ] button to select [Test Print], and press the [OK] button.
Printer Diag
Test Print
Test Print
TestPat600 [IOT]
Use the [ ] button to select [Gradation], and press the [OK] button.
Test Print
Gradation
Gradation
Ready
Gradation
Processing
Gradation
Ready
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
Test Print
6-39
ZaS060601AA
6-40
6.6.3 Gradation
The Gradation (ESS built-in test pattern) prints the broken border patterns with the density of 0 to 100%.
ZaS060602AA
6-41
Regi
Range
Description
Slow Scan K to P
-15 to +15
-15 to +15
Displays or changes the registration adjustment values of Fast Scan Smp MPF (MSI).
-15 to +15
Displays or changes the registration adjustment values of Fast Scan Smp Tray 1
(Standard Tray).
-15 to +15
Displays or changes the registration adjustment values of Fast Scan Smp Tray 2
(Optional Tray).
-15 to +15
Displays or changes the registration adjustment values of Fast Scan Dup MPF (MSI).
-15 to +15
Displays or changes the registration adjustment values of Fast Scan Dup Tray 1
(Standard Tray).
-15 to +15
Displays or changes the registration adjustment values of Fast Scan Dup Tray 2
(Optional Tray).
Procedure
The following procedure explains how to change the registration value using [Fast Scan Smp MPF] as an
example.
1
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [Parameter], and press the [OK] button.
Printer Diag
Parameter
Parameter
Regi
6-42
Parameter
Regi
Regi
SlowScan KtoP
Use the [ ] button to select [FastScanSmp MPF], and press the [OK] button.
FastScanSmp MPF
0 *
Regi
FastScanSmp MPF
Use the [ ] or [ ] button to change the value, and press the [OK] button.
FastScanSmp MPF
-2
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
Parameter
6-43
Life
Description
Fusing PV
Fusing Heattime
Trans Unit PV
Drum PV
Drum Thickness
Toner Pixel
Procedure
The following procedure describes how to change the life counter value of Fusing Heattime as an example.
1
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [Parameter], and press the [OK] button.
Printer Diag
Parameter
Parameter
Regi
Use the [ ] button to select [Life], and press the [OK] button.
Parameter
Life
Life
Fusing PV
Use the [ ] button to select [Fusing Heattime], and press the [OK] button.
Life
Fusing Heattime
Fusing Heattime
Reading
6-44
Fusing Heattime
38
To initialize the life counter value of Fusing Heattime, press the [<--] (Back) button to return to the
level immediately previous to the level where you displayed the value, use the [ ] button to
select [Initialize], and then select the [OK] button.
Fusing Heattime
Reading
Fusing Heattime
Initialize
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
Parameter
6-45
When you print the parameter list, check that the Tray 1 contains A4 paper (Only A4 paper is supported). If
the parameter list is printed on the paper of other than A4, some part of the image might be lost.
The printer will display [Processing] and suspend the parameter list from printing, if the paper size other
than A4 is set as the default paper tray setting.
In this case, switch off the printer once, and on again, specify A4 for the paper tray setting, enter the CE
mode, and then print the list.
Procedure
1
Confirm that the [Printer Diag] is selected, and then press the [OK] button.
Use the [ ] button to select [Parameter], and then press the [OK] button.
Printer Diag
Parameter
Parameter
Regi
Use the [ ] button to select [Print], and press the [OK] button.
Parameter
Print
Print Parameter
Ready
Print Parameter
Processing
Print Parameter
Ready
Press the [<--] (Back) button to return to the [Printer Diag] screen.
Printer Diag
Parameter
6-46
Error
CHECK OK
Note
***: Displays the name of the test ended in error.
(Fax Flash W/R / SRAM W/R / Fax Card I/F / AFE Serial I/F /
IIT I/F/ ASIC IJAC / ASIC JBIG)
Error
CHECK OK
Note
***: Displays the name of the test ended in error.
(Fax Flash W/R / SRAM W/R)
Error
CHECK OK
Note
***: Displays the name of the test ended in error.
(Fax Card I/F / AFE Serial I/F / IIT I/F)
6-47
Note
Normal
Error
CHECK OK
Relay Toggle
Test
Relay Set Test
Hook Test
Hook Toggle
Test
Hook Set Test
Range
Description
0150 - 9999
ON, OFF
0150 - 9999
ON, OFF
0Hz
400Hz
462Hz
1080Hz
1100Hz
1300Hz
Single Tone
Send
1500Hz
1650Hz
1850Hz
2100Hz
500Hz
600Hz
900Hz
1000Hz
DTMF Send
DTMF Continuous
0 - 9, A - D, *, #
DTMF
Individually
16 digits
(each digit 0 - 9,
A - D, *, #)
6-48
Range
DP10 Individually
10 digits
(each digit: 0 - 9)
DP20 Individually
10 digits
(each digit: 0 - 9)
Description
Sends the multiple digits dial pulse (10pps)
signal.
Sends the multiple digits dial pulse (20pps)
signal.
Sends the data specified with speed and pattern (no pattern for V.34).
5 patterns
5 patterns
5 patterns
5 patterns
V.34 33600bps
V.34 31200bps
V.34 28800bps
V.34 26400bps
V.34 24000bps
V.34 21600bps
V.34 19200bps
V.34 31200bps
V.34 16800bps
V.34 14400bps
V.34 12000bps
V.34 9600bps
Data Send
V.34 7200bps
V.34 4800bps
V.34 2400bps
V.29 9600bps
V.29 7200bps
V.29 4800bps
V.27ter 4800bps
V.27ter 2400bps
V.21 300bps
V.17 14400bps
V.17 12000bps
V.17 9600bps
V.17 7200bps
Line Voltage
Line Current
6-49
Use the [ ] button to select [Fax/Scanner Diag], and press the [OK] button.
Fax/Scanner Diag
Board Test
Board Test
All test
Use the [ ] button to select [Relay/Signal Test], and press the [OK] button.
Board Test
Relay/Signal Test
Relay/Signal Test
Relay Test
Use the [ ] button to select [DTMF Send], and press the [OK] button.
Relay/Signal Test
DTMF Send
DTMF Send
DTMF Continuous
DTMF Continuous
DTMF:0
Use the [ ] or [ ] button to change the value and then press the [OK] button to start sending
the signal.
DTMF Continuous
DTMF:5
Now Sending Signal
DTMF Continuous
DTMF:5
DTMF Continuous
DTMF:5
6-50
Press the [<--] (Back) button to return to the [Fax Scanner Diag] screen.
Fax/Scanner Diag
Board Test
10
6-51
6.9 Information
6.9.1 Scan Counter
Displays the scan counter value.
Procedure
1
Use the [ ] button to select [Fax/Scanner Diag], and press the [OK] button.
Use the [ ] button to select [Information], and press the [OK] button.
Fax/Scanner Diag
Information
Information
Scan Counter
Scan Counter
FB: 0x00000001
DADF:0x00000002
Press the [<--] (Back) button to return to the [Fax Scanner Diag] screen.
Fax/Scanner Diag
Information
6-52
Item
Normal
Error
Auto Adjust(FB)
Adjust OK
Auto Adjust(DADF)
Adjust OK
Range
Description
Coeff FB RED
Coeff FB GREEN
Coeff FB BLUE
4 digits (hexadecimal)
(each digit 0 - 9, A - F)
Coeff FB GRAY
Coeff DADF RED
Coeff DADF GREEN
Coeff DADF BLUE
4 digits (hexadecimal)
(each digit 0 - 9, A - F)
2 digits (hexadecimal)
(each digit 0 - 9, A - F)
Target GRAY
6-53
Range
Description
Regi FB Lead
Regi FB Side
Regi DADF Lead (Front)
Regi DADF Side (Front)
Range
Auto Registration
Description
Enables or disables the auto registration adjustment feature.
ON, OFF
Range
Description
6-54
Range
Description
2 digits (hexadecimal)
(each digit 0 - 9, A - F)
Mag FB COLOR
Mag FB GRAY
Mag DADF COLOR
Mag DADF GRAY
Range
Description
Sensor Status
Description
ON or OFF
6-55
Set ON
Set OFF
Forward
FB Motor
Now Driving
Check NG
Reverse
Forward
DADF Motor
Now Driving
Check NG
Reverse
DADF
Solenoid
Description
Error
Set ON
Set OFF
Check OK
Sensor Status
6-56
Error
Abnormal End
Use the [ ] button to select [Fax/Scanner Diag], and press the [OK] button.
Use the [ ] button to select [Parameter], and press the [OK] button.
Parameter
Chain Link: 101-001
Value(Hex): B5
Fax/Scanner Diag
Parameter
Cursor
4
Change the Chain Link number, and press the [OK] button.
Use the [ ] and [ ] buttons to move the cursor to right and left.
Use the [ ] and [ ] buttons to increase or decrease the value where the cursor is placed.
Press the [OK] button, and the Chain Link number changed will appear.
Parameter
Chain Link: 101-007
Value(Hex): B5
Cursor
5
Parameter
Chain Link: 101-007
Value(Hex): *43
6
Press the [<--] (Back) button to return the [Fax Scanner Diag] screen.
Fax/Scanner Diag
Parameter
6-57
Factory
Default
Note
0-255
128
SYS002 _DEF_SCN_START
_LINE
0-255
128
840
SYS003 _DEF_SCN_MAG_
C
Scanner Magnification
(Color)
0-255
128
840
SYS101 _DEF_SCN_MAG_
G
Scanner Magnification
(Gray)
0-255
128
840
004
SYS_DEF_SCN_CARRIGE_POS
0-60
840
005
SYS_DEF_ADF_START_DOT
0-255
128
840
008
SYS_DEF_ADF_START_DOT2
0-255
128
840
006
SYS_DEF_ADF_START_LINE
0-255
159
840
009
SYS_DEF_ADF_START_LINE2
0-255
153
840
007
SYS_DEF_ADF_MAG_C
0-255
144
840
102
SYS_DEF_ADF_MAG_G
0-255
144
700
003
SYS_DEF_FBC2_CLR_R
065535
36213
0 - 2^16-1
700
004
SYS_DEF_FBC2_CLR_G
065535
37734
0 - 2^16-1
700
005
SYS_DEF_FBC2_CLR_B
065535
36786
0 - 2^16-1
700
006
SYS_DEF_FBC2_MONO
37636
0 - 2^16-1
700
007
065535
36874
0 - 2^16-1
700
008
37813
0 - 2^16-1
700
009
065535
37159
0 - 2^16-1
700
010
065535
38557
0 - 2^16-1
Parameter
Chain
Link
840
SYS001 _DEF_SCN_START
_DOT
840
Name
6-58
0 - 60
Factory
Default
0-255
240
0 - 255
SYS_DEF_ASTGT_CLR_G
0-255
240
0 - 255
103
SYS_DEF_ASTGT_CLR_B
0-255
240
0 - 255
700
104
SYS_DEF_ASTGT_MONO
240
0 - 255
700
700
106
700
107
700
108
700
109
700
110
SYS_DEF_ADFC2_MONO_DW
950
100
IIT_AFE_REG_VER
SION
Parameter
Chain
Link
700
101
SYS_DEF_ASTGT_CLR_R
700
102
700
SYS_DEF_IIT_AUTOREG
SYS_DEF_AD-
FC2_CLR_R_DW
SYS_DEF_AD-
FC2_CLR_G_DW
SYS_DEF_AD-
FC2_CLR_B_DW
Name
Note
0-10
0 mm - 10 mm
0,1
0: Enable
1: Disable
065535
31402
065535
32085
065535
32358
065535
31948
0,1
0:M0-1
1:M0-1mod
950
101
IMAGE_PREPRM_THROUGH1
0-255
192
bit0 0: AFE
bit1 1: Shading Correction
bit2 2: GAP Correction
bit3 3: Mirror Processing
bit4 4: Masking Processing
bit5 5: White Balance
Machine Difference
Correction
bit6 6: Lamp Initial Start
Up Attribute Correction
bit7 7: ADF Lamp Time
Variation Attribute Correction
950
102
IMAGE_PREPRM_THROUGH2
0-255
6-59
950
Link
103
Parameter
Name
Range
950
104
950
950
6-60
0-255
0-255
0-255
Factory
Default
Note
Link
Parameter
950
107 DIAG_IMG_PATH
950
108
950
Name
Range
Factory
Default
Note
0 = Normal Operation
1 = Raw Image Output
1
2 = Raw Image Output
2
3 = 1 Dot Grid Output
4 = Vertical Gradation
Output
5 = Horizontal Gradation Output
6 = Solid Color Output
7 = Lamp On Silent
Image Output
8 = Lamp Off Silent
Image Output
9 = Shading Memory
Silent Image Output
10 = FXIF Test
11 = Patch Pattern
12 = AFE: Maximum
Transient Status
13 = AFE: Lamp
14 = AFE: Fixed Data
Output
0-255
DIAG_IMG03_GRID
_SIZE
01023
200
109
DIAG_IMG04_GRADATION
1-255
10
950
110
DIAG_IMG05_GRADATION
1-255
10
Horizontal Gradation
Step
950
111 DIAG_IMG06_R_LV
0-255
128
950
112 DIAG_IMG06_G_LV
0-255
128
950
113 DIAG_IMG06_B_LV
0-255
128
950
065535
950
065535
950
116
DIAG_IMG09_TEMP
Reserve
950
117 DIAG_IMG11_R_LV
790
308 FAX_DEF_CL
0,1
0: Standard
1: Fine
2: Super Fine
3: Photo
790
304 FAX_DEF_RESO
6-61
0-3
Factory
Default
0-2
0: Text
1: Text & Photo
2: Photo
-3-+3
-3 (Lighter3) - +3
(Darker3)
FAX_DEF_DELAY_H
0-23
21
0 h - 23 h
307
FAX_DEF_DELAY_M
0-59
0 min - 59 min
701
006
SYS_SET_FAX_TRANS
SystemSetting Sent/Unsent
Report
0-2
0: Do Not Deliver
1: Deliver Upon Error
2: Always Deliver
701
007
SYS_SET_FAX_BROAD
SystemSetting Broadcast
Report
0-2
0: Do Not Deliver
1: Deliver Upon Error
2: Always Deliver
701
008
SYS_SET_FAX_PROTOCOL
SystemSetting Protocol
Monitor
0-2
0: Do Not Deliver
1: Deliver Upon Error
2: Always Deliver
790
305
FAX_SET_SD_HEAD
0,1
0: Do Not Record
1: Record
825
200
FAX_COVER_NOTE
0,1
0: Disable
1: Enable
701
FAX_SET_COUN001
TRY
cFax
Cntry
Unkn
own
821
205 FAX_SET_CL_FAX
821
FAX_SET_DUS403
CARD_SIZE
821
407
821
Parameter
Name
Chain
Link
790
302
FAX_DEF_ORIG_TYPE
790
301
FAX_DEF_DENSITY
790
306
790
Note
cFaxCntryUnite Unknown
dStates
0,1
0: Disable
1: Enable
0-2
0: New Page
1: Cut Without New
Page
2: Auto Reduce
FAX_SET_DUP_PRT
0,1
0: 1 Sided
1: 2 Sided
411
SYS_SET_FAX_ACT
0,1
0: No Auto Delivery
1: Always Deliver
825
002
FAX_SET_LINE_TYPE
0,1
0: PSTN
1: PBX
825
003
FAX_SET_DIAL_TYPE
0-2
0: PB
1: DP (10PPS)
2: DP (20PPS)
6-62
825
Link
Parameter
006 FAX_SET_DRPD
Name
Range
Factory
Default
Note
0-7
0: Disable
1: Pattern1
2: Pattern2
3: Pattern3
4: Pattern4
5: Pattern5
6: Pattern6
7: Pattern7
0: For Tel Only
1: For Fax Only
2: Switch Tel/Fax
3: Switch Ans/Fax
4: DRPD Mode
825
014
FAX_SET_RCV_MODE
0-4
825
017
FAX_SET_AT_TELFAX
FaxSetting AutoAnswerTel
/ Fax Call Time
0-255
0 - 255 sec
825
018
FAX_SET_AT_ANSFAX
0-255
0 - 255 sec
825
019 FAX_SET_AT_FAX
FaxSetting AutoAnswer
Fax Call Time
0-255
0 - 255 sec
825
031 FAX_SET_RESND
0-5
0 - 5 times
825
032 FAX_SET_REDIAL
0-13
0 - 13 times
825
034
FAX_SET_INT_REDIAL
1-15
1 - 15 min
825
035
FAX_SET_INT_TIMER
FaxSetting Communication
Interval Timer
3-255
3 - 255 sec
825
054
FAX_SET_HOOK_THRESH
825
060 FAX_SET_DM_PRE
FaxSetting DM Prevent
Feature
825
FAX083
_SET_RING_VOL
825
096
825
Lower
Normal
Higher
0,1
0: Do Not Prevent
1: Prevent
0-3
0: OFF
1: Min
2: Middle
3: Max
FaxSetting Remote
Receive
0,1
0: Disable
1: Enable
FAX097 _SET_RMT_RCV_T
ONE1
FaxSetting Remote
Receive Tone 1st Digit
0-9
825
FAX098 _SET_RMT_RCV_T
ONE2
FaxSetting Remote
Receive Tone 2nd Digit
0-9
825
102
FAX_SET_PREFIX_SET
0,1
825
103
FAX_SET_PREFIX_NUM
FAX_SET_RMT_RCV
6-63
0: Do Not Add
1: Add
UINT8*5
Chain
Link
825
FAX_SET_LINE_602
MONI
825
635
FAX_SET_CAPAB_ECM
Name
Range
Factory
Default
Note
0-3
0: OFF
1: Min
2: Middle
3: Max
0,1
0: Disable
1: Enable
825
701
0-4
0 :2400
1: 4800
2: 9600
3: 14400
4: 33600
701
10
FAX_SET_FOWD_SET
0,2
0: Do Not Transfer
2: Always Transfer
701
11
FAX_SET_FOWD_PRT
0,1
0: Do Not Print
1: Print
701
12
FAX_SET_FWD_ERR_PRT
0,1
0: Do Not Print
1: Print
820
001
DIAG_DIALLING_TYPE
Dial Type
0-2
821
101
DIAG_SYS_MACHINE_MODE
Operation Mode
0,1
821
201
DIAG_CONTINUE_ILLEGAL
821
202
DIAG_THRESH_MEMRX
0-100
821
203
DIAG_THRESH_RXPRINT
Transit to Immediate
Receive
0-99
821
204
DIAG_THRESH_MEMTX
0-100
821
206
DIAG_THRESH_COLOR_FAX_RX
0-2
821
207
DIAG_THRESH_GC_START
0-99
6-64
Name
Range
Chain
Link
821
401
DIAG_PAGE_MARGIN
0-127
821
406
DIAG_COLOR_RX_PAGE_LIMIT
0-64
701
009
DIAG_SEL_OPP_NAME
790
401
DIAG_G3M_RX_RESO
0-128
821
412
DIAG_PAGE_MARGIN_REDUCTION
0-127
825
001 DIAG_NCU_TYPE
825
004
DIAG_DP_RELAY_DELAY
0-255
825
005
DIAG_DRPD_ENABLE
0,1
825
013
DIAG_DIS_DP_20PPS
0,1
825
015
DIAG_CNG_DETECT_TIME
0-255
0-255
NCU Type
0,1
0,1
825
016
DIAG_AUTO_ANSWER_TIME
825
025
DIAG_RING_CYCLE_MIN
0-255
825
026
DIAG_RING_CYCLE_MAX
8-255
825
027
DIAG_SELECT_DIALTONE
0-3
825
028
DIAG_BUSYTONE_FREQ
0-4
825
029
DIAG_BUSYTONE_PATTERN
0-8
825
030
DIAG_BUSYTONE_DETECTION
0,1
825
DIAG_NUM033 BER_OF_REDIAL_MAX
0-255
825
036
DIAG_CAPAB_NUM_CHECK
0,1
6-65
Factory
Default
Note
0: Name of Recipient
Channel (to be displayed when an individual protocol is used.)
1: Phone Number
0x00: Normal
0x80: R8x3.85
Link
Parameter
Name
825
037
DIAG_NUM_CHECK_TIMER
1-255
825
045
DIAG_DAA_REG73
0
RingThreshold
0-255
825
046
DIAG_DAA_REG73
1
Complex
0-2
825
047
DIAG_DAA_REG73
3
DCCurve
0-4
825
048
DIAG_DAA_REG73
4
Rmake
825
049
DIAG_DAA_REG74
F
FastEdgePulseDial
825
050 DIAG_DAA_MODE
825
062
825
Range
Factory
Default
Note
0-255
0,1
0-255
DIAG_NUM_DIAL_PULSE
0-2
063
DIAG_PB_TONE_TIME
PB Transmission Time
0-255
825
064
DIAG_PB_INTERDIGIT
PB Pause Time
0-255
825
065
DIAG_PB_ATT_LEVEL
4-15
825
066
DIAG_PB_LEVEL_SUB
0-15
825
067
DIAG_MAKE_10PPS
1-106
825
068
DIAG_BREAK_10P
PS
1-106
825
069
DIAG_MAKE_20PPS
1-106
825
070
DIAG_BREAK_20P
PS
1-106
825
071
DIAG_DP_INTERDIGIT
0-255
825
0-255
825
073 DIAG_BLIND_TIME
0-255
825
DIAG_TIME_TO_074 DETECT_DIALTONE
0-255
825
079
DIAG_ONHOOK_DETECT_TIME
10255
825
080
DIAG_OFFHOOK_DETECT_TIME
15255
6-66
Name
Range
Factory
Default
Note
Chain
Link
825
DIAG_OFFHOOK_081 DETECT_TIME_RING
825
DIAG_EX_RING084 ER_FREQ_ON_TIME
825
DIAG_EX_RING085 ER_FREQ_OFF_TIME
825
086
DIAG_EX_RINGER_ON_T1
5-250
825
087
DIAG_EX_RINGER_OFF_T2
5-250
825
088
DIAG_EX_RINGER_ON_T3
5-250
825
089
DIAG_EX_RINGER_OFF_T4
5-250
825
090
DIAG_DIS_DIALTONE_PSTN
0,1
825
DIAG_MANU092 AL_CED_START_TIME
0-255
825
093
0-255
825
DIAG_MANU094 AL_CNG_START_TIME
0-255
825
099
DIAG_RING_ON_JUDGE
0-255
825
100
DIAG_RING_OFF_JUDGE
0-255
825
101
DIAG_RING_OFFMAX
0-255
825
103
DIAG_PREFIX_NUM_1
0-255
825
104
DIAG_PREFIX_NUM_2
PrefixDial Number2
0-255
825
105
DIAG_PREFIX_NUM_3
PrefixDial Number3
0-255
825
106
DIAG_PREFIX_NUM_4
PrefixDial Number4
0-255
825
107
DIAG_PREFIX_NUM_5
PrefixDial Number5
0-255
825
108
DIAG_SIDAA_MANUAL_CALIBRATION
DIAG_CNG_SEND_
START_TIME
6-67
15255
0,1
Name
Range
Chain
Link
825
110
825
DIAG_DIAL111 TONE_ONOFFPTN_MIN
0-255
825
DIAG_DIAL112 TONE_ONOFFPTN_MAX
8-255
825
201
DIAG_NCU_COUNTRY_RELAY
0,1
825
202
DIAG_DAA_REG73
2
FastEdgePulseDial2
0,2
825
203
DIAG_DAA_REG_E
MI
825
601
DIAG_LINE_MONITOR_ENABLE
0,1
825
604
DIAG_CED_DETECT_TIMER
25255
825
666
DIAG_MANUAL_CNG_SIGNAL
0,1
825
605
DIAG_CNG_STOP_
SELECT
0,2
825
608
DIAG_RTN_TX_RATE
0-100
825
609
DIAG_RTN_TX_LINE
0-255
825
610
DIAG_G3M_CALL_T1_TIMER
0-255
825
611
DIAG_G3M_TX_T1_TIMER
0-255
825
612
DIAG_G3M_RX_T1_TIMER
0-255
825
613
DIAG_G3M_T2_TIMER
T2 Timer Value
0-255
825
614
DIAG_G3M_T3_TIMER
T3 Timer Value
0-255
825
615
DIAG_G3M_AUTO_T4_TIMER
Auto Send/Receive T4
Timer Value
0-255
825
616
DIAG_G3M_MAN_T
4_TIMER
Manual Send/Receive T4
Timer Value
0-255
825
617
DIAG_G3M_IVL_TIMER
0-255
DIAG_DIS_DIALTONE_PATTERN
6-68
Factory
Default
Note
0,1
0-255
Name
Range
Chain
Link
825
618
DIAG_G3M_FSK_CHK_TIMER
0-255
825
619
DIAG_ITUT_PIX_DELAY
0-255
825
620
825
621
DIAG_G3M_NSF_DIS_TIME
NSF/DIS Transmission
Time
0-3
825
622
DIAG_G3M_TX_MODEM_SPEED
Communication Mode
Upon Sending (Speed)
0-5
825
623
DIAG_G3M_RX_MODEM_SPEED
Communication Mode
Upon Receiving (Speed)
0-5
825
625
DIAG_G3M_DIS_IG
NORE_NO
825
626
DIAG_G3M_TSI_CI
G_MODE
0-2
825
627
DIAG_G3M_WITH_
CSI
CSI Send
0,1
825
628
DIAG_G3M_FTT_FALLBACK
0-2
825
629
DIAG_G3M_TCF_CHECK
0,1
825
630
0-3
825
631
DIAG_G3M_RX_CABLE_EQU
0-4
825
632
DIAG_G3M_TAP_H
OLD
TAP HOLD
0,1
825
633
DIAG_G3M_V29_E
PT
EP Tone
0,1
825
634
DIAG_EXTENDED_DIS_DTC
0-10
825
636
DIAG_G3M_CTC_N
O
ECM/CTC Transmission
Times
0-7
825
637
DIAG_G3M_T5_TIMER
0-255
825
638
DIAG_G3M_EQM_4
8
0-127
825
639
DIAG_G3M_EQM_7
2
0-127
825
640
DIAG_G3M_EQM_9
6
0-127
6-69
0-255
0-255
Factory
Default
Note
Link
Parameter
Name
825
641
DIAG_G3M_EQM_1
20
0-127
825
642
DIAG_G3M_EQM_1
44
0-127
825
643
0-127
825
644
0-127
825
DIAG_G3M_V34_645 MAX_SYMBOL_RATE
825
646
825
DIAG_G3M_V34_S
647 YM_RATE_ENABLE1
825
648
825
Range
0-5
1-14
0-61
DIAG_G3M_V34_BI
T_RATE_ENABLE1
0-255
649
DIAG_G3M_V34_BI
T_RATE_ENABLE2
0-63
825
650
DIAG_G3M_V34_CTRL_BIT_RATE
825
DIAG_G3M_V34_BI
653 T_RATE_THRESHOLD
825
655
825
DIAG_G3M_V34_MAX_BIT_RATE
Note
0,1
0-255
DIAG_G3M_V8_TE
_TIME
V8Te Time
0-255
656
DIAG_G3M_V34_CC_TIMER
5-255
825
657
DIAG_G3M_V34_SHIFT_G3
0,1
825
658 DIAG_CAPAB_V34
V34 Capability
0,1
825
659
DIAG_ANSAM_SEND_TIME
825
660
DIAG_ANSAM_START_TIME
22255
825
661
DIAG_G3M_TX_CODING
0-3
825
662
DIAG_G3M_RX_CODING
0-3
825
664
DIAG_RX_GAIN_ADJUSTMENT
0-255
6-70
Factory
Default
1-255
Name
Range
Chain
Link
825
665
DIAG_G3M_V34_FRAME_SIZE
825
667
DIAG_TONE_TX_ATT
0-15
825
668 DIAG_RX_ATT
Incoming Level
0-3
825
669
DIAG_SAVE_ERROR_RX_DATA
0,1
825
673
DIAG_DFAULT_JBIG_LRLTWO
0,1
825
DIAG_EX702 TEL_HOOK_THRESH_0
0-255
825
DIAG_EX703 TEL_HOOK_THRESH_1
0-255
825
DIAG_EX704 TEL_HOOK_THRESH_2
0-255
825
DIAG_CAPAB_EX705 TEL_HOOK_SUPPLEMENT
0,1
825
10-20
950
DIAG_FOR001 GET_ERROR_SECRET
0-255
950
002
950
DIAG_PMQA003 T_BOARD_SECRET
950
004
DIAG_DONT_DEL_
TXFILE
0,1
950
005
DIAG_DONT_PR_R
CVFILE
0,1
950
006
DIAG_MON_SPEED_38400
0,1
950
007
DIAG_COMM_TIME_MEASURE
0,1
950
008
DIAG_WITHOUT_ICM
0,1
950
009
DIAG_COMM_PARAM
0,1
DIAG_CODE_CHECK_SECRET
Note
0,1
0-255
0-255
6-71
Factory
Default
0: Disable
1: Enable
Name
Range
Factory
Default
Note
Chain
Link
950
010 DIAG_EQM_READ
0,1
950
011
DIAG_AGCVAL_READ
0,1
950
DIAG_FAX012 COM_DEBUG_INFO
950
013
DIAG_G3M_V8_SHIFT_G3
0,1
950
014
DIAG_SERIMON_RX_ENABLE
0,1
950
015
DIAG_CODEC_DEBUG_DISP
0,1
950
016
DIAG_WARMBOOT_DISABLE
0,1
950
017
DIAG_FORCED_POLLING
0,1
950
018
DIAG_REMOTE_DIAG
0,1
950
019 DIAG_ECM_RX_64
0,1
950
020 DIAG_ECM_TX_64
0,1
950
021 DIAG_SELECT_LN
0-2
950
022
DIAG_CAPAB_FULLCOLOR
950
118
DIAG_FREQ_DETECT_LEVEL
825
DIAG_AN708 SWER_DELAY_MINIMUM
0-255
0: Disable
1 - 255 sec
825
DIAG_AN709 SWER_DELAY_MAXIMUM
0-255
0: Disable
1 - 255 sec
825
710 DIAG_DIS_DP
825
DIAG_FAX707 LINE_TEST_VOLTAGETHRESH
0,1
0,1
Frequency Detect Level
(For Filter)
6-72
0-3
0: Allow DP
1: Restrict DP
0,1
10-50
10 - 50
1Step/1V
Item
Description
All Clear
User Clear
System Clear
User&System Clear
System Data Init
Document Clear
System
User&
System
SW Bug History
Diag History
Local ID G3
Local Name
TX Header Logo
System Counter
Email Subject
Email Text
Calling Table
6-73
Document
System
Data
All
Data
All
User
System
User&
System
Document
Substitute Queue
Document Number
System
Data
Procedure
The following procedure explains how to clear the data using [User Clear] as an example.
1
Use the [ ] button to select [Fax/Scanner Diag], and press the [OK] button.
6-74
Use the [ ] button to select [BackUp Data], and press the [OK] button.
Fax/Scanner Diag
BackUp Data
BackUp Data
All Clear
Use the [ ] button to select [User Clear], and press the [OK] button.
BackUp Data
User Clear
User Clear
Ready
User Clear
Processing
User Clear
Complete
Press the [<--] (Back) button to return to the [BackUp Data] screen.
BackUp Data
User Clear
Press the [<--] (Back) button to return to the [Fax Scanner Diag] screen.
Fax/Scanner Diag
BackUp Data
6-75
6-76