Professional Documents
Culture Documents
Design of Saddle Support For Horizontal Pressure Vessel
Design of Saddle Support For Horizontal Pressure Vessel
International Journal of Mechanical, Aerospace, Industrial, Mechatronic and Manufacturing Engineering Vol:8, No:12, 2014
International Science Index, Mechanical and Mechatronics Engineering Vol:8, No:12, 2014 waset.org/Publication/9999835
1967
scholar.waset.org/1999.8/9999835
International Science Index, Mechanical and Mechatronics Engineering Vol:8, No:12, 2014 waset.org/Publication/9999835
E
Y
7750
192
260
Material
SA516 Gr70
0.3
1
M
= Q A (1
1+
QL
4
1+
R2 H
2 A L )
4 H
3 L
2 (R 2 H 2 )
(
1+
L2
4 H
A
L
3 L
428.64 mm
152.00 cm
203.20 mm
176.00 mm
1200
421.28mm
1407.17 kgf/cm2
1407.17 kgf/cm2
(1.00)
(1.00)
1549 kgf
16 mm
16 mm
16 mm
M1 = 1549 20.32 (1
= 113.3kgf m
2
M2 =
1549 152
4
1+ 2 (
(
428.64 421.28
2
152
4 421.28
1+
3 152
)
4
20.32
152
= 117.4kgf m
1968
scholar.waset.org/1999.8/9999835
P R
2 t
1 =
8 .4 5 4 2 8 .6 4
1 1 7 .4
= 1 2 1 .6 1 kg f / cm 2
4 2 8 .6 4 2 1 4 .7 2
2 1 4 .7 2
International Science Index, Mechanical and Mechatronics Engineering Vol:8, No:12, 2014 waset.org/Publication/9999835
2 t
8.45 428.64
2 =
=
2
Rm t
117.4
= 124.32 kgf / cm
2 14.72
428.64 14.72
3 =
P R
2 t
8.45 428.64
2 14.72
1
2
113.3
428.64 2 14.72
= 124.32 kgf / cm 2
4 =
P R
2 t
8.45 428.64
2 14.72
R
113.3
1
2
m
= 121.66 kgf / cm
428.64 14.72
( L 2
4
L +
H
3
A )
1549 (152 2 20 . 32 )
4
152 +
421 . 28
3
= 828 . 7 kgf
1969
scholar.waset.org/1999.8/9999835
Sr.
No.
International Science Index, Mechanical and Mechatronics Engineering Vol:8, No:12, 2014 waset.org/Publication/9999835
1
2
3
4
TABLE II
COMPARISON OF STRESSES
Manual
ANSYS
Stress Location
Scl
Result
Result
and Type
(kgf/cm2)
(kgf/cm2)
1
Scl 10
121.61
110.63
2
Scl 6
124.32
107.47
3
Scl 1
124.32
113.59
4
Scl 9
121.61
109.21
Allowable
Stress
(kgf/cm2)
1407.17
1407.17
1407.17
1407.17
VII. CONCLUSION
APPENDIX
1970
scholar.waset.org/1999.8/9999835
International Science Index, Mechanical and Mechatronics Engineering Vol:8, No:12, 2014 waset.org/Publication/9999835
= Poisson Ratio
Rm = radius of the pressure vessel, mm.
L = length of the P.V. from tangent to tangent line, mm.
A = distance between saddle Centre and tangent line, mm.
b = width of the base plate, mm.
t = thickness of shell, mm.
Q = Maximum reaction load at the saddle, kgf or N.
1, 2 = Longitudinal stresses in the shell at top and bottom of mid
span, kgf/cm2 .
3, 4= Longitudinal stress at top and bottom of saddle, kgf/cm2.
M1 = Maximum longitudinal bending moment at the saddle, N-m or
kgf-m.
M2 = Maximum longitudinal bending moment between the saddle
supports, N-m or kgf-m.
= angle of contact of saddle with shell, degree.
E1 = Joint efficiency
Circ. = Circumferential
REFERENCES
[1]
1971
scholar.waset.org/1999.8/9999835